537e2229b6
schematics: swap U2,U9
7 years ago
5f15062265
schematics: comments on switcher parts corrected
7 years ago
95cb151b39
schematic power sheet: alternatives to AP3429/A, swap U4,U5
7 years ago
5384b84706
schematics: switching regulator alternatives
7 years ago
6cc027aed0
schematics: update inductor PN, swap L2 <-> L3
7 years ago
ce6120680b
schematics: I2C SM8 footprint assigned
7 years ago
380fcdf86a
schematic: newly created SOT96-1 used for NXP RTC
7 years ago
e641702054
schematics: start with tape and reel datasheet information
...
(currently done only for RTC)
7 years ago
3915779e0c
schematics: part numbers and URLs of datasheets and manufacturers
...
of most chips and connectors. Small parts not done yet.
7 years ago
020d7bdfa7
schematics: change core voltage 1.2V->1.1V (RB1 changed 15k->18k)
...
FPGA Chip in ULX3S is LFE5U-45F-6BG381C and it needs 1.1V.
5G chips like LFE5U5G-45F-6BG381C would need 1.2V
7 years ago
52814d6ae0
WIFI LED (blue) on schematics
7 years ago
4a35c95132
GPDI CEC add protection resistor R61 470 ohm
7 years ago
a5a51a8f28
connected missing SD card pins to esp-32
7 years ago
cca17d282d
open-close to check that everything loads fine
7 years ago
35b3a8b3dd
changing to 45F which is production device now
...
schem symbol 45F fixed typo T8->T7 (GND) and SERDES
7 years ago
154645af07
on schematics write revision 1.7.0 to match similar
...
writing on PCB v1.7
7 years ago
7cebd0afa5
changing DAC resistors 100-820 ohm -> 150-1200 ohm
...
few 220 ohm resistors changed to 150 ohm to simplify BOM
7 years ago
8e94190676
power up note and small cosmetics
7 years ago
050a70079a
move one audio-v pin from bank0 to bank7 so
...
now all audio jack pins are on bank7
7 years ago
6d74bb29fc
PCB v1.7 fix wrong audio jack connection
7 years ago
ba4c8e8d22
PCB v1.6 SDRAM fully reworked
7 years ago
bc41b3052d
move WIFI disable jumper closer to BTN1
7 years ago
220f575442
schematic "power" sheet and footprint cosmetics
7 years ago
1ea88bda53
Adding pins to schematic symbols for all chips in unit "H" (SERDES)
...
Non-serdes chips need GND connection on unit "H".
"power" sheet now connects GND's at unit "H".
7 years ago
d57b16519c
update (I hope) all chip units to 85F
...
add more GND vias
7 years ago
fffde2cf88
Additional GND for 85F chips
7 years ago
e4fc99887e
moving GND and VCC on schematics symbols to
...
common locations for planned PCB which
supports upgrade path for example
12F->25F->45F->85F and if possible ECP5U->ECP5UM
7 years ago
35598e53fb
FT231X workaround blues
7 years ago
06a8d751d9
Jumpers (default OFF) for 3 switcher voltages
7 years ago
bc4b88ee58
Micro SD: using SCHD3A0100
7 years ago
f3d84dbfdc
LED D19 was oriented wrong, now correct
7 years ago
bab7ee607e
placeholder for 1.5k pullup for usb 1.0
7 years ago
9cc436ce8c
Additional VCC 2.2uF blocking capacitors near the switching
...
power supply to form PI-filter with another 2.2uF near BGA
7 years ago
68a23c127c
set package SOD323 to all small diodes
7 years ago
aef23559d2
3D models for capacitors inductors transistors and some resistors
7 years ago
f32ace3adf
D15 schottky diode BAT54W package SOD323F
7 years ago
bcf94bafab
buttons footprints correct now
7 years ago
2ca8acc32d
ADC chip moved on top layer.
...
Connecting 8 analog lines to J2
and remaining VCC/GND
7 years ago
2153a220a0
schematic symbol for ADC MAX11123
...
small PCB traces cleanup
ADC chip placed on PCB but connected only to GND
7 years ago
278ac6b341
2.2uF for ESP-32 and gerber update
8 years ago
81b3ea5da0
adding minimal set of 3 2.2uF capacitor for 1.2V, 2.5V and 3.3V
8 years ago
ee7d266543
Resistors for LEDs
8 years ago
18aef04f2c
JTAG header
8 years ago
238ad770ce
moving USB LEDs on TOP layer
8 years ago
1a122bfc67
fully routed
8 years ago
0f9d00f602
Buffer capacitor for SDRAM
8 years ago
aeaf64f99c
connecting all BTNs except power BTN
8 years ago
dcbfda0556
Run DRC to update cupper fill zones
8 years ago
1e5e0b01a6
connecting JTAG lines to FTDI serial lines RI DCD CTS DSR
...
as those pins are by default inputs and can be reconfigured as outputs
similar but not identical pinout as the one that works from ujprog
CBUS used to force-wakeup of the board from sleep state
2 LEDs to CBUS pins to display usb enumeration and activity status
8 years ago
39dce76f0a
use new schem symbol
8 years ago
Emard