853497d403
schematics: replace 45F chip with 85F
7 years ago
b006a34b71
schematics: C54 22uF for 3V RTC battery
7 years ago
3996e140ef
schematics: kicad 5 load and save
7 years ago
7b88b3baf1
schematics: v1.8 adding capacitor for 2.5/3.3V
7 years ago
1911c0afe2
schematics: add capacitor near SDRAM
7 years ago
db50639a60
schematics: 4 22nF capacitors for 2.5/3.3V and 3.3V near J1 and J2 connector
7 years ago
ec8c012ebb
schematics: jumper for selectable 2.5V/3.3V J1 voltage
7 years ago
4ae602347e
schematics: power decoupling capactor near OLED
7 years ago
42e3255b7a
schematics: US2 diodes pull up/down 1.5k/15k
7 years ago
d95e2eab3d
schematics: 3 decoupling 22nF capacitors for SDRAM
7 years ago
2f3cc59274
schematics: adding mouser P/N
7 years ago
b205d52f4f
schematics: sprinkling 22nF decoupling capacitors under FPGA
7 years ago
a04b74cc61
schematics, footprints: micro usb cleanup
7 years ago
6079a51257
schematics: symbol for SDRAM copied from rescue to proper library
7 years ago
965d04d7d5
schematics: WIFI LED on GPIO5, route WIFI_GPIO5 and WIFI_GPIO17 to FPGA
7 years ago
804ac1c309
schematics: Add some PN's for the BOM
7 years ago
e81d05b68d
schematics: renaming pins J..+- to GP,GN..
7 years ago
5b7c755ee1
schematics: flip audio 0-3
7 years ago
3fa407e54f
schematics: use 12-bit dac instead of 8-bit
7 years ago
f4d7692c91
schematics: SD card symbol with 2 CD pins connected to GND
7 years ago
3915779e0c
schematics: part numbers and URLs of datasheets and manufacturers
...
of most chips and connectors. Small parts not done yet.
7 years ago
52814d6ae0
WIFI LED (blue) on schematics
7 years ago
7cebd0afa5
changing DAC resistors 100-820 ohm -> 150-1200 ohm
...
few 220 ohm resistors changed to 150 ohm to simplify BOM
7 years ago
050a70079a
move one audio-v pin from bank0 to bank7 so
...
now all audio jack pins are on bank7
7 years ago
0d71e508ae
analog: audio ring2 resistor DAC network connected to FPGA
...
copper infill is getting thin, so minimal-thickness traces
are used 0.127 mm
7 years ago
6d74bb29fc
PCB v1.7 fix wrong audio jack connection
7 years ago
ba4c8e8d22
PCB v1.6 SDRAM fully reworked
7 years ago
1ea88bda53
Adding pins to schematic symbols for all chips in unit "H" (SERDES)
...
Non-serdes chips need GND connection on unit "H".
"power" sheet now connects GND's at unit "H".
7 years ago
e4fc99887e
moving GND and VCC on schematics symbols to
...
common locations for planned PCB which
supports upgrade path for example
12F->25F->45F->85F and if possible ECP5U->ECP5UM
7 years ago
07de158d38
R56 for FT231X rev A,B,C workaround from TN140_FT231X Errata
7 years ago
bc4b88ee58
Micro SD: using SCHD3A0100
7 years ago
bab7ee607e
placeholder for 1.5k pullup for usb 1.0
7 years ago
f120d212d9
433 MHz onboard antenna (need to uncover copper infill layers)
7 years ago
0229a768ad
FPGA direct-to-pin Hackish USB transciver 27 ohm + 3.6 V zener
7 years ago
6d14ed8ff0
Placing DIP switch, but not yet connecting it to FPGA
8 years ago
37bb008e24
ADC connecting REF+/REF- and SPI
8 years ago
2ca8acc32d
ADC chip moved on top layer.
...
Connecting 8 analog lines to J2
and remaining VCC/GND
8 years ago
32836831ae
i2c of RTC connected to GPDI i2c
8 years ago
ee20b46f6d
connecting ADC substrate pad to GND
8 years ago
2153a220a0
schematic symbol for ADC MAX11123
...
small PCB traces cleanup
ADC chip placed on PCB but connected only to GND
8 years ago
be09416928
Add 27 ohm resistors in series with FTDI USB and readme update
8 years ago
278ac6b341
2.2uF for ESP-32 and gerber update
8 years ago
ee7d266543
Resistors for LEDs
8 years ago
18aef04f2c
JTAG header
8 years ago
b7500cc477
increasing thickness of power traces, moving clock
...
to a bank which is always at 3.3V
8 years ago
2a60828a99
schem. pullup 1.5k for USB 1.1 full speed mode
8 years ago
23b588ff16
Routing... 4 routes remaining
8 years ago
0f9d00f602
Buffer capacitor for SDRAM
8 years ago
1e5e0b01a6
connecting JTAG lines to FTDI serial lines RI DCD CTS DSR
...
as those pins are by default inputs and can be reconfigured as outputs
similar but not identical pinout as the one that works from ujprog
CBUS used to force-wakeup of the board from sleep state
2 LEDs to CBUS pins to display usb enumeration and activity status
8 years ago
d6fd30e59c
jumper to disable wifi module
8 years ago
davor