davor
|
49bf3b64cc
|
PCB: silkscreen cosmetics, moving texts around for visibility
|
7 years ago |
|
davor
|
0671e14733
|
PCB: spacing RV2 RV3 away from 2.54 mm thru-holes
|
7 years ago |
|
davor
|
d5ec90d78f
|
PCB: separate RV2 RV3 for soldermask to enter inbetween
|
7 years ago |
|
davor
|
8f4e6ffc42
|
PCB: Q1, Q2 non-handsoldering footprint
|
7 years ago |
|
davor
|
d0275f9cef
|
PCB: USB diodes and jumpers with smaller (non-handsoldering) pads
|
7 years ago |
|
davor
|
a38926d559
|
PCB: moving C1, C21, C50 away from J1, J2 connectors
|
7 years ago |
|
davor
|
2e357a510c
|
PCB: 3D model of IDC 2.54mm headers
|
7 years ago |
|
Emard
|
ea89e1c3d9
|
PCB: battery holder 3D model in place
|
7 years ago |
|
davor
|
9196448978
|
PCB: 3D models for HDMI and audio jack
|
7 years ago |
|
davor
|
383913bf97
|
PCB: trac cosmetix
|
7 years ago |
|
davor
|
e13cab6d5f
|
PCB: moving US2 VIAs from under the footprint to the front of solder pads.
Better to avoid any chance of short circuit with connector shell.
|
7 years ago |
|
davor
|
be3ef7a678
|
PCB v1.8.9
|
7 years ago |
|
davor
|
78e398513c
|
PCB: track cosmetix around US2 and copper pour
|
7 years ago |
|
davor
|
46709c1772
|
PCB: 3D view replaced didoes with 0-ohm resistors
|
7 years ago |
|
davor
|
00ed12e81d
|
PCB v1.8.8
|
7 years ago |
|
Emard
|
9a1ce975d9
|
PCB v1.8.7: SD card rotated 180 deg
|
7 years ago |
|
Emard
|
5263a5dff5
|
PCB: unclutter silkscreen
|
7 years ago |
|
davor
|
e452e7a4aa
|
PCB: don't output fabrication layers, they don't look good.
Parts center positions should be used instead.
|
7 years ago |
|
davor
|
0938c3045e
|
PCB: silkscreen cosmetix around RTC
|
7 years ago |
|
davor
|
fe37b87904
|
PCB v1.8.6: fixing RTC time loss issue with RC network
|
7 years ago |
|
davor
|
02f9aad964
|
PCB: v1.8.5
|
7 years ago |
|
davor
|
0621a2dc9c
|
PCB: DIP Switch pulled up by 2.5/3.3V line, not fixed 3.3V
|
7 years ago |
|
davor
|
4fd3073327
|
PCB: GPDI1 was missing from fabrication output (attribute now set to "Surface mount")
|
7 years ago |
|
davor
|
581f70b0e1
|
PCB: U2 was missing from fabrication output (attribute now set to "Surface mount")
|
7 years ago |
|
davor
|
7e8f9fff2e
|
PCB: Remove R56 RV2 RV3 from fabrication output list (footprint attribute set to "Virtual")
|
7 years ago |
|
davor
|
db2a1e6d41
|
PCB: v1.8.4
|
7 years ago |
|
davor
|
d852596b60
|
PCB: joining differential track which had separated
|
7 years ago |
|
davor
|
73fe099a7c
|
PCB: move 5V track bit away from the edge
|
7 years ago |
|
davor
|
7357e8d9a2
|
PCB: join differential tracks that had separated
|
7 years ago |
|
davor
|
268a9fad91
|
PCB: trac cosmetix around GPDI GND
|
7 years ago |
|
davor
|
8727e4feed
|
PCB: redundand routing for buttons
|
7 years ago |
|
davor
|
19ebc2bfe1
|
PCB: trac cosmetix around SDRAM
|
7 years ago |
|
davor
|
85c17afe89
|
PCB: new inductors footprint and trac cosmetix around them
|
7 years ago |
|
davor
|
ea933eefe7
|
PCB: remove 3D models from resistors which should not be soldered
|
7 years ago |
|
davor
|
8f751545b2
|
PCB: reloaded with new U11 i2c schematic symbol
|
7 years ago |
|
davor
|
f3701f7f3e
|
PCB: J2 silkscreen labels
|
7 years ago |
|
davor
|
40e7ad7400
|
PCB: v1.8.3
|
7 years ago |
|
davor
|
a6d1e66dea
|
PCB: unclutter silkscreen and trac cosmetix
|
7 years ago |
|
davor
|
cd2c041273
|
PCB: resistor footprints changed, unclutter silkscreen again
|
7 years ago |
|
davor
|
7592c8a448
|
PCB: unclutter silkscreen (mostly done)
|
7 years ago |
|
Emard
|
81e30ee0f2
|
PCB: unclutter silkscreen (partially done)
|
7 years ago |
|
davor
|
e51217fa05
|
PCB: audio DAC resistors moved closer to each other
|
7 years ago |
|
davor
|
a3cbf3e2cc
|
PCB: re-run DRC
|
7 years ago |
|
davor
|
4dae36d912
|
PCB: silkscreen clean up battery markings
|
7 years ago |
|
davor
|
97010a4d39
|
PCB: add PIN1 dot to usbserial chip U6 FT231X
|
7 years ago |
|
davor
|
0e0680c05f
|
PCB: change voltage and wifi pin headers to vertical and
their respective 3D models keep horizontal
|
7 years ago |
|
davor
|
4c907b1887
|
PCB: update footprints for fixed voltage selector jumpers
|
7 years ago |
|
davor
|
285b688f98
|
PCB: gerbers don't output Adhes layers (currently they would be output as empty)
|
7 years ago |
|
davor
|
369fc1976e
|
PCB: oled LED 3D model purged from bak file
|
7 years ago |
|
davor
|
4a36e36213
|
PCB: removing unexistent 3D LED shape so 3D viewer no longer complains.
|
7 years ago |
