davor
|
32bd7673a8
|
schematics: v1.7.14
|
7 years ago |
|
davor
|
ea96ac0d18
|
schematics: use non-handsoldering footprints for all 22nF and 100nF capacitors
|
7 years ago |
|
davor
|
8ff6e0e20e
|
schematics update, setting L1,L2,L3 all the same PN
|
7 years ago |
|
davor
|
b535b7ccee
|
schematics: references for buttons on previous PCB v1.7
|
7 years ago |
|
davor
|
2f3cc59274
|
schematics: adding mouser P/N
|
7 years ago |
|
davor
|
b205d52f4f
|
schematics: sprinkling 22nF decoupling capacitors under FPGA
|
7 years ago |
|
davor
|
a04b74cc61
|
schematics, footprints: micro usb cleanup
|
7 years ago |
|
davor
|
6079a51257
|
schematics: symbol for SDRAM copied from rescue to proper library
|
7 years ago |
|
davor
|
7caf7a4f5f
|
schematics: v1.7.9 SD card hopfully connected properly to ESP32 SD_MMC
|
7 years ago |
|
davor
|
fd6a0d3a2a
|
schematics: bump version to v1.7.8
|
7 years ago |
|
davor
|
08e107ae65
|
schematics: detach SD card connection from ESP32, it won't
boot when this is connected.
|
7 years ago |
|
davor
|
f4d7692c91
|
schematics: SD card symbol with 2 CD pins connected to GND
|
7 years ago |
|
Emard
|
6cc027aed0
|
schematics: update inductor PN, swap L2 <-> L3
|
7 years ago |
|
Emard
|
380fcdf86a
|
schematic: newly created SOT96-1 used for NXP RTC
|
7 years ago |
|
Emard
|
a5a51a8f28
|
connected missing SD card pins to esp-32
|
7 years ago |
|
Emard
|
a135164670
|
increase schematic version to 1.7.1
|
7 years ago |
|
Emard
|
154645af07
|
on schematics write revision 1.7.0 to match similar
writing on PCB v1.7
|
7 years ago |
|
Emard
|
ba4c8e8d22
|
PCB v1.6 SDRAM fully reworked
|
7 years ago |
|
davor
|
e4fc99887e
|
moving GND and VCC on schematics symbols to
common locations for planned PCB which
supports upgrade path for example
12F->25F->45F->85F and if possible ECP5U->ECP5UM
|
7 years ago |
|
Emard
|
07de158d38
|
R56 for FT231X rev A,B,C workaround from TN140_FT231X Errata
|
7 years ago |
|
davor
|
2153a220a0
|
schematic symbol for ADC MAX11123
small PCB traces cleanup
ADC chip placed on PCB but connected only to GND
|
8 years ago |
|
Emard
|
be09416928
|
Add 27 ohm resistors in series with FTDI USB and readme update
|
8 years ago |
|
Emard
|
ee7d266543
|
Resistors for LEDs
|
8 years ago |
|
davor
|
b7500cc477
|
increasing thickness of power traces, moving clock
to a bank which is always at 3.3V
|
8 years ago |
|
davor
|
2a60828a99
|
schem. pullup 1.5k for USB 1.1 full speed mode
|
8 years ago |
|
davor
|
23b588ff16
|
Routing... 4 routes remaining
|
8 years ago |
|
davor
|
0f9d00f602
|
Buffer capacitor for SDRAM
|
8 years ago |
|
Davor
|
39dce76f0a
|
use new schem symbol
|
8 years ago |
|
davor
|
c297a5294f
|
adding 25 MHz oscillator and moving some parts around
|
8 years ago |
|
Davor
|
12e89e677a
|
connecting wifi, usbserial, oled, sd card
|
8 years ago |
|
Davor
|
a477fbd050
|
connecting flash config chip
|
8 years ago |
|
davor
|
85cb0b3f93
|
Placing 40-pin connectors side-by-side,
changing ft2232 to ft231x
|
8 years ago |
|
davor
|
4f3fabdb5f
|
oled updated on the schematic and PCB
|
8 years ago |
|
davor
|
6639abded3
|
add 4 mounting holes
|
8 years ago |
|
davor
|
f9ba6fa20b
|
chage ESP8266-12E to ESP32S
approximate (maybe incorrect) connections - need review
(programming esp from fpga, jtag, sd, chip enable)
|
8 years ago |
|
davor
|
7fd0f561fc
|
Add SPI flash chip
|
8 years ago |
|
davor
|
aa8fac622b
|
SD card to sperate "sdcard" sheet
small rearranging and comments
|
8 years ago |
|
davor
|
4b5faa4f58
|
eeprom for FT2232
|
8 years ago |
|
Davor
|
ddd08e597e
|
JTAG port to USB sheet
|
8 years ago |
|
Davor
|
17ba085b6f
|
audio jack to "analog" sheet
|
8 years ago |
|
Davor
|
af36200b80
|
add audio jack footprint
|
8 years ago |
|
Davor
|
c1205abfb4
|
Add 3V battery CR1225 holder footprint
|
8 years ago |
|
Davor
|
4a87d52a9d
|
allow FTDI to force power up of the board
|
8 years ago |
|
Davor
|
8ed3d57c66
|
Add wake on RTC and shutdown network
|
8 years ago |
|
Davor
|
133417070a
|
add RTC to power sheet
Moving wifi to separate sheet
|
8 years ago |
|
Davor
|
24e8015ff0
|
move usb to "usbserial" sheet and add ft2232 footprint
move sdram to "ram" sheet
create "wifi" sheet
|
8 years ago |
|
Davor
|
c95d2d7b18
|
GPDI to separate sheet
|
8 years ago |
|
Davor
|
e9c1620c89
|
Moving LEDs, OLED and buttons to "blinkey" sheet
|
8 years ago |
|
Davor
|
b20aaeb5c0
|
added SDRAM TSOP-54 package
|
8 years ago |
|
Davor
|
f6e596d4ee
|
add SDRAM chip (probably wrong footprint)
|
8 years ago |
