PCB for ULX3S FPGA R&D board. Fork Sand fork of https://github.com/emard/ulx3s https://www.forksand.com/
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
davor 2a6adff571
readme update (connect DONE pin to ESP32)
7 years ago
doc sdcard part numbers info 7 years ago
footprints ECP5 85E schematic footprint 7 years ago
pic pictures update from 3D preview 7 years ago
plot LED D19 was oriented wrong, now correct 7 years ago
spice SPICE: increasing RC load constants to simulate delayed response 7 years ago
tools BOM CSV generation tool 7 years ago
.gitignore use new footprint for crystal oscillator 8 years ago
README.md readme update (connect DONE pin to ESP32) 7 years ago
analog.bak LED D19 was oriented wrong, now correct 7 years ago
analog.sch placeholder for 1.5k pullup for usb 1.0 7 years ago
blinkey.bak LED D19 was oriented wrong, now correct 7 years ago
blinkey.sch LED D19 was oriented wrong, now correct 7 years ago
flash.bak LED D19 was oriented wrong, now correct 7 years ago
flash.sch using modified ECP5 footprint 7 years ago
fp-lib-table use new footprint for crystal oscillator 8 years ago
gpdi.bak LED D19 was oriented wrong, now correct 7 years ago
gpdi.sch using modified ECP5 footprint 7 years ago
gpio.bak LED D19 was oriented wrong, now correct 7 years ago
gpio.sch using modified ECP5 footprint 7 years ago
power.bak LED D19 was oriented wrong, now correct 7 years ago
power.sch using modified ECP5 footprint 7 years ago
ram.bak LED D19 was oriented wrong, now correct 7 years ago
ram.sch using modified ECP5 footprint 7 years ago
sdcard.bak LED D19 was oriented wrong, now correct 7 years ago
sdcard.sch update SD card power supply and gerbers 7 years ago
ulx3s-cache.lib using modified ECP5 footprint 7 years ago
ulx3s-rescue.lib using modified ECP5 footprint 7 years ago
ulx3s.bak LED D19 was oriented wrong, now correct 7 years ago
ulx3s.kicad_pcb LED D19 was oriented wrong, now correct 7 years ago
ulx3s.kicad_pcb-bak LED D19 was oriented wrong, now correct 7 years ago
ulx3s.pro using modified ECP5 footprint 7 years ago
ulx3s.sch schematic symbol for ADC MAX11123 8 years ago
usb.bak LED D19 was oriented wrong, now correct 7 years ago
usb.sch using modified ECP5 footprint 7 years ago
wifi.bak LED D19 was oriented wrong, now correct 7 years ago
wifi.sch placeholder for 1.5k pullup for usb 1.0 7 years ago

README.md

ULX3S PCB

This is work-in-progress place for putting some wishes of a small (94x51 mm) FPGA board.

Instead of describing in written, it is better explained when drawn in kicad:

kicad ulx3s.pro

Schematics is mostly complete. PCB routing is mostly complete too.

3D preview

TOP BOTTOM

Features

FPGA: Lattice ECP5 LFE5U-25F-6BG381C

USB: FTDI FT231XS (1Mbit JTAG and 3Mbit usbserial)

GPIO: All differential, PMOD-friendly

RAM: 32MB SDRAM MT48LC16M16

Flash: 8MB SPI flash S25FL164 for FPGA config

Storage: Micro-SD slot

LEDs: 10 (8 blink-LEDs, 2 USB leds)

Buttons: 7 (4 direction, 2 fire, 1 power button)

Audio: 3.5 mm stereo jack

Video: GPDI connector with 3.3V-5V I2C bidirectional level shifter

Display: placeholder for 0.96-1.3" SPI OLED COLOR or B/W

WiFi+bluetooth: placeholder for ESP-32 (JTAG and serial over WiFi possible)

ADC: 8 channels, 12 bit, 1 MSa/s MAX11123

Power: 3 Switching voltage regulators: 1.2V, 2.5V, 3.3V

Clock: 25 MHz onboard, external differential clock input

Low power sleep: RTC clock wakeup, power button, 32768 Hz quartz and battery

GPDI is General Purpose Differential Interface, Electrically LVDS, mostly TMDS tolerant female receptacle more-or-less compatible with digital monitors/TVs

Todo

Make the prototype.

[x] Silkscreen Double outline for BGA chip
[ ] Silkscreen do not write over the solder pads
[ ] Silkscreen BGA names on ESP32 placeholder and 2.54 mm headers
[x] Silkscreen JTAG signal names on 6-pin 2.54 mm header
[x] Silkscreen remove OLED outline
[x] Solder stop mask must go inbetween all SMD chip pads
[x] External differential clock input at J1_33 +/-
[ ] Thinner copper, more spacing to SDRAM-FPGA
[x] physically sprinkle VCC blocator capacitors under BGA
[ ] Values on silkscreen
[ ] Dedicated antenna pin
[ ] onboard 433 antenna (lower side, remove GND infill)
[x] Resistors for LEDs
[x] Move USB LEDs from bottom to top side
[ ] Improve SDRAM routing - use VIAs for closest pins
[x] Increase thickness of power lines (5V, 3.3V, 2.5V)
[x] Compile a f32c bitstream using the schematics
[x] Compile differential GPDI output
[x] Connect more lines from ESP-32 to FPGA
[x] Connect FPGA USB D+/D- with 1.5k pullup in USB 1.1 (full speed) mode
[x] FPGA USB add 27 ohm + 3.6 V zener
[x] Symmetrically place USB connectors left-right 
[ ] Jumpers to switch 2.5V/3.3V for left IO banks
[x] External JTAG header
[x] Move JTAG 2 mm left
[ ] Move WiFi Disable jumper above the buttons
[x] Sprinkle 2.2uF capacitors on power lines
[x] Spice simulation of power-up/shutdown network
[x] 27ohm D+/D- to FT231XS
[x] DIP switch (4 switches)
[x] MAX11123 ADC SPI
[x] I2C for RTC
[x] main usb connector on top side 
[ ] space screw to other parts
[x] move battery away from screw hole
[x] top layer GND fill
[x] R25 move away from oled screw hole
[ ] board cut off nothches inisde for space saving
[x] DIP switch to the right near RAM
[x] Move HDMI a bit closer to OLED
[x] 32768Hz oscillator footprint
[ ] SD card footprint wrong
[x] move USB 0.5-1mm more out
[x] DIP SW footprint correct
[x] AUDIO jack footprint fits
[ ] AUDIO jack pin 4 not connected
[x] BTN footprint too small
[ ] SMPS switcher jumpers for initial testing
[ ] DONE ČED (fpga programming)