PCB for ULX3S FPGA R&D board. Fork Sand fork of https://github.com/emard/ulx3s https://www.forksand.com/
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
Emard 775c304aee
PCB: swap U4,U5, move via a bit away from switcher pad
7 years ago
doc doc short file on where to find info how to correctly prepare 7 years ago
footprints footprint sdram pin pitch increased 0.8 mm -> 0.8077 mm 7 years ago
pic pic update 7 years ago
plot gerbers update PCB v1.7.1 7 years ago
spice SPICE: increasing RC load constants to simulate delayed response 7 years ago
tools BOM CSV generation tool 7 years ago
.gitignore use new footprint for crystal oscillator 8 years ago
README.md schematics: text labels that enumerate differential pairs on 2.54mm connector 7 years ago
analog.bak schematics: part numbers and URLs of datasheets and manufacturers 7 years ago
analog.sch schematics: part numbers and URLs of datasheets and manufacturers 7 years ago
blinkey.bak schematics: part numbers and URLs of datasheets and manufacturers 7 years ago
blinkey.sch schematics: part numbers and URLs of datasheets and manufacturers 7 years ago
flash.bak schematics: using SOA008 and adding datasheet url to FTDI usbserial 7 years ago
flash.sch schematics: use SOA008 footprint for the SPI flash chip 7 years ago
fp-lib-table schematics: use SOA008 footprint for the SPI flash chip 7 years ago
gpdi.bak schematics: use SOA008 footprint for the SPI flash chip 7 years ago
gpdi.sch schematics: I2C SM8 footprint assigned 7 years ago
gpio.bak schematics: part numbers and URLs of datasheets and manufacturers 7 years ago
gpio.sch schematics: part numbers and URLs of datasheets and manufacturers 7 years ago
power.bak schematic power sheet: alternatives to AP3429/A, swap U4,U5 7 years ago
power.sch schematic power sheet: alternatives to AP3429/A, swap U4,U5 7 years ago
ram.bak schematics: part numbers and URLs of datasheets and manufacturers 7 years ago
ram.sch schematics: part numbers and URLs of datasheets and manufacturers 7 years ago
sdcard.bak schematics: part numbers and URLs of datasheets and manufacturers 7 years ago
sdcard.sch schematics: part numbers and URLs of datasheets and manufacturers 7 years ago
ulx3s-cache.lib schematics: change core voltage 1.2V->1.1V (RB1 changed 15k->18k) 7 years ago
ulx3s-rescue.lib open-close to check that everything loads fine 7 years ago
ulx3s.bak schematics: switching regulator alternatives 7 years ago
ulx3s.kicad_pcb PCB: swap U4,U5, move via a bit away from switcher pad 7 years ago
ulx3s.kicad_pcb-bak PCB: swap U4,U5, move via a bit away from switcher pad 7 years ago
ulx3s.pro cosmetix: LED D22 moved a bit left to be symmetrical 7 years ago
ulx3s.sch schematics: update inductor PN, swap L2 <-> L3 7 years ago
usb.bak schematics: update inductor PN, swap L2 <-> L3 7 years ago
usb.sch schematics: using SOA008 and adding datasheet url to FTDI usbserial 7 years ago
wifi.bak schematics: part numbers and URLs of datasheets and manufacturers 7 years ago
wifi.sch schematics: part numbers and URLs of datasheets and manufacturers 7 years ago

README.md

ULX3S PCB

This is work-in-progress place for putting some wishes of a small (94x51 mm) FPGA board.

ULX3S = University digital logic Learning eXtensible board release 3 with SDRAM, Successor of ULX2S.

kicad ulx3s.pro

Schematics is mostly complete. PCB routing is mostly complete too.

3D preview

TOP BOTTOM

Features

FPGA: Lattice ECP5 LFE5U-45F-6BG381C

USB: FTDI FT231XS (1Mbit JTAG and 3Mbit USB-serial)

GPIO: 56 pins (28 differential pairs), PMOD-friendly

RAM: 32MB SDRAM MT48LC16M16

Flash: 8MB SPI flash S25FL164 for FPGA config

Storage: Micro-SD slot

LEDs: 11 (8 blink-LEDs, 2 USB LEDs, 1 WiFi LED)

Buttons: 7 (4 direction, 2 fire, 1 power button)

Audio: 3.5 mm jack with 4 contacts (analog stereo + digital audio or composite video)

Video: GPDI connector with 3.3V-5V I2C bidirectional level shifter

Display: placeholder for 0.96-1.3" SPI OLED COLOR or B/W

WiFi+bluetooth: placeholder for ESP-32 (JTAG and serial over WiFi)

ADC: 8 channels, 12 bit, 1 MSa/s MAX11123

Power: 3 Switching voltage regulators: 1.2V, 2.5V, 3.3V

Clock: 25 MHz onboard, external differential clock input

Low power sleep: RTC clock wakeup, power button, 32768 Hz quartz and battery

GPDI is General Purpose Differential Interface, Electrically LVDS, mostly TMDS tolerant female receptacle more-or-less compatible with digital monitors/TVs

Todo

Make the prototype.

[x] Silkscreen Double outline for BGA chip
[x] Silkscreen do not write over the solder pads
[ ] Silkscreen BGA names on ESP32 placeholder and 2.54 mm headers
[x] Silkscreen JTAG signal names on 6-pin 2.54 mm header
[x] Silkscreen remove OLED outline
[x] Solder stop mask must go inbetween all SMD chip pads
[x] External differential clock input at J1_33 +/-
[ ] Thinner copper, more spacing to SDRAM-FPGA
[x] physically sprinkle VCC blocator capacitors under BGA
[ ] Values on silkscreen
[x] Dedicated antenna pin
[x] onboard 433 antenna
[x] 433 remove GND and silkscreen test point
[x] Resistors for LEDs
[x] Move USB LEDs from bottom to top side
[x] Improve SDRAM routing - use VIAs for closest pins
[x] Increase thickness of power lines (5V, 3.3V, 2.5V)
[x] Compile a f32c bitstream using the schematics
[x] Compile differential GPDI output
[x] Connect more lines from ESP-32 to FPGA
[x] Connect FPGA USB D+/D- with 1.5k pullup in USB 1.1 (full speed) mode
[x] FPGA USB add 27 ohm + 3.6 V zener
[x] Symmetrically place USB connectors left-right 
[ ] Jumpers to switch 2.5V/3.3V for left IO banks
[x] External JTAG header
[x] Move JTAG 2 mm left
[x] Move WiFi Disable jumper closer to the BTN1 (angled header)
[x] Sprinkle 2.2uF capacitors on power lines
[x] Spice simulation of power-up/shutdown network
[x] 27ohm D+/D- to FT231XS
[x] DIP switch (4 switches)
[x] MAX11123 ADC SPI
[x] I2C for RTC
[x] main usb connector on top side 
[ ] space screw to other parts
[x] move battery away from screw hole
[x] top layer GND fill
[x] R25 move away from oled screw hole
[ ] board cut off nothches inisde for space saving
[x] DIP switch to the right near RAM
[x] Move HDMI a bit closer to OLED
[x] 32768Hz oscillator footprint
[x] SD card footprint SCHD3A0100
[ ] SD use CD (card detect) contacts
[x] move USB 0.5-1mm more out
[x] DIP SW footprint correct
[x] AUDIO jack footprint fits
[x] AUDIO jack pin 4 (ring2) connected to 4-bit DAC
[x] BTN footprint too small
[x] SMPS jumpers default OFF for prototype testing
[x] FPGA DONE to ESP-32
[x] Diodes manual soldering
[x] R56: FT231X rev A,B,C TXDEN to GND
    workaround from TN140_FT231X Errata
[x] PCB for LFE5UM ready (some GND will change to
    VCC for Serdes power supply, see LFE5U->LFE5UM
    migration docs)
[x] Check GND/VCC for 45 and 85 packages,
    for example pin T11 is NC on 25U, GND on 85U and VCC ond 85UM