|
|
|
|
/**
|
|
|
|
|
* Marlin 3D Printer Firmware
|
|
|
|
|
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
|
|
|
*
|
|
|
|
|
* Based on Sprinter and grbl.
|
|
|
|
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
|
|
|
|
*
|
|
|
|
|
* This program is free software: you can redistribute it and/or modify
|
|
|
|
|
* it under the terms of the GNU General Public License as published by
|
|
|
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
|
|
|
* (at your option) any later version.
|
|
|
|
|
*
|
|
|
|
|
* This program is distributed in the hope that it will be useful,
|
|
|
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
|
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
|
|
|
* GNU General Public License for more details.
|
|
|
|
|
*
|
|
|
|
|
* You should have received a copy of the GNU General Public License
|
|
|
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
|
|
|
*
|
|
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
/**
|
|
|
|
|
* Gen7 Alfons3 board pin assignments
|
|
|
|
|
*
|
|
|
|
|
* These Pins are assigned for the modified GEN7 Board from Alfons3.
|
|
|
|
|
* Please review the pins and adjust them for your needs.
|
|
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
|
|
|
|
|
#error "Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu."
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#define BOARD_NAME "Gen7 Custom"
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Limit Switches
|
|
|
|
|
//
|
|
|
|
|
#define X_STOP_PIN 0
|
|
|
|
|
#define Y_STOP_PIN 1
|
|
|
|
|
#define Z_STOP_PIN 2
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Steppers
|
|
|
|
|
//
|
|
|
|
|
#define X_STEP_PIN 21 // different from standard GEN7
|
|
|
|
|
#define X_DIR_PIN 20 // different from standard GEN7
|
|
|
|
|
#define X_ENABLE_PIN 24
|
|
|
|
|
|
|
|
|
|
#define Y_STEP_PIN 23
|
|
|
|
|
#define Y_DIR_PIN 22
|
|
|
|
|
#define Y_ENABLE_PIN 24
|
|
|
|
|
|
|
|
|
|
#define Z_STEP_PIN 26
|
|
|
|
|
#define Z_DIR_PIN 25
|
|
|
|
|
#define Z_ENABLE_PIN 24
|
|
|
|
|
|
|
|
|
|
#define E0_STEP_PIN 28
|
|
|
|
|
#define E0_DIR_PIN 27
|
|
|
|
|
#define E0_ENABLE_PIN 24
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Temperature Sensors
|
|
|
|
|
//
|
|
|
|
|
#define TEMP_0_PIN 2 // Analog Input
|
|
|
|
|
#define TEMP_BED_PIN 1 // Analog Input (pin 34 bed)
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Heaters
|
|
|
|
|
//
|
|
|
|
|
#define HEATER_0_PIN 4
|
|
|
|
|
#define HEATER_BED_PIN 3 // (bed)
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Misc. Functions
|
|
|
|
|
//
|
|
|
|
|
#define SDSS 31 // SCL pin of I2C header || CS Pin for SD Card support
|
|
|
|
|
#define PS_ON_PIN 19
|
|
|
|
|
|
|
|
|
|
// A pin for debugging
|
|
|
|
|
#define DEBUG_PIN -1
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// LCD / Controller
|
|
|
|
|
//
|
|
|
|
|
#define BEEPER_PIN -1
|
|
|
|
|
|
|
|
|
|
// 4bit LCD Support
|
|
|
|
|
#define LCD_PINS_RS 18
|
|
|
|
|
#define LCD_PINS_ENABLE 17
|
|
|
|
|
#define LCD_PINS_D4 16
|
|
|
|
|
#define LCD_PINS_D5 15
|
|
|
|
|
#define LCD_PINS_D6 13
|
|
|
|
|
#define LCD_PINS_D7 14
|
|
|
|
|
|
|
|
|
|
// Buttons are directly attached
|
|
|
|
|
#define BTN_EN1 11
|
|
|
|
|
#define BTN_EN2 10
|
|
|
|
|
#define BTN_ENC 12
|
|
|
|
|
|
|
|
|
|
// RS485 pins
|
|
|
|
|
//#define TX_ENABLE_PIN 12
|
|
|
|
|
//#define RX_ENABLE_PIN 13
|
