You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

121 lines
3.1 KiB

/**
* AZTEEG_X3_PRO (Arduino Mega) pin assignments
*/
#include "pins_RAMPS_13.h"
#undef FAN_PIN
#define FAN_PIN 6 //Part Cooling System
#define BEEPER 33
#define CONTROLLERFAN_PIN 4 //Pin used for the fan to cool motherboard (-1 to disable)
//Fans/Water Pump to cool the hotend cool side.
#define EXTRUDER_0_AUTO_FAN_PIN 5
#define EXTRUDER_1_AUTO_FAN_PIN 5
#define EXTRUDER_2_AUTO_FAN_PIN 5
#define EXTRUDER_3_AUTO_FAN_PIN 5
//
//This section is to swap the MIN and MAX pins because the X3 Pro comes with only
//MIN endstops soldered onto the board. Delta code wants the homing endstops to be
//the MAX so I swapped them here.
//
#ifdef DELTA
#undef X_MIN_PIN
#undef X_MAX_PIN
#undef Y_MIN_PIN
#undef Y_MAX_PIN
#undef Z_MIN_PIN
#undef Z_MAX_PIN
#define X_MIN_PIN 2
#define X_MAX_PIN 3
#define Y_MIN_PIN 15
#define Y_MAX_PIN 14
#define Z_MIN_PIN 19
#define Z_MAX_PIN 18
#endif
//
#ifdef Z_PROBE_ENDSTOP
//#undef Z_MIN_PIN
//#define Z_MIN_PIN 15
#define Z_PROBE_PIN 19
#endif
//
#define E2_STEP_PIN 23
#define E2_DIR_PIN 25
#define E2_ENABLE_PIN 40
#define E3_STEP_PIN 27
#define E3_DIR_PIN 29
#define E3_ENABLE_PIN 41
#define E4_STEP_PIN 43
#define E4_DIR_PIN 37
#define E4_ENABLE_PIN 42
#undef HEATER_1_PIN
#undef HEATER_2_PIN
#undef HEATER_3_PIN
#define HEATER_1_PIN 9
#define HEATER_2_PIN 16
#define HEATER_3_PIN 17
#define HEATER_4_PIN 4
#define HEATER_5_PIN 5
#define HEATER_6_PIN 6
#define HEATER_7_PIN 11
#undef TEMP_2_PIN
#undef TEMP_3_PIN
#define TEMP_2_PIN 12 // ANALOG NUMBERING
#define TEMP_3_PIN 11 // ANALOG NUMBERING
#define TEMP_4_PIN 10 // ANALOG NUMBERING
#define TC1 4 // ANALOG NUMBERING Thermo couple on Azteeg X3Pro
#define TC2 5 // ANALOG NUMBERING Thermo couple on Azteeg X3Pro
//
//These Servo pins are for when they are defined. Tested for usage with bed leveling
//on a Delta with 1 servo. Running through the Z servo endstop in code.
//Physical wire attachment was done on EXT1 on the GND, 5V, and D47 pins.
//
#undef SERVO0_PIN
#undef SERVO1_PIN
#undef SERVO2_PIN
#undef SERVO3_PIN
#ifdef NUM_SERVOS
#define SERVO0_PIN 47
#if NUM_SERVOS > 1
#define SERVO1_PIN -1
#if NUM_SERVOS > 2
#define SERVO2_PIN -1
#if NUM_SERVOS > 3
#define SERVO3_PIN -1
#endif
#endif
#endif
#endif
//LCD Pins//
#if defined(VIKI2) || defined(miniVIKI)
#define BEEPER 33
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 44
#define DOGLCD_CS 45
#define LCD_SCREEN_ROT_180
//The encoder and click button
#define BTN_EN1 22
#define BTN_EN2 7
#define BTN_ENC 39 //the click switch
#define SDSS 53
#define SDCARDDETECT 49
#define KILL_PIN 31
#endif
#ifdef TEMP_STAT_LEDS
#define STAT_LED_RED 32
#define STAT_LED_BLUE 35
#endif