forksand
/
marlin-lulzbot-laser
1
1
Fork 0
Code Issues Pull Requests Releases Wiki Activity

merge from the branch bkubicek/Marlin/zalmmerge

Browse Source
master
Bernhard Kubicek 13 years ago
parent d7c4f0780b
commit 00674af3a8
20 changed files with 4067 additions and 3869 deletions
Show Stats Download Patch File Download Diff File

463
Marlin/Configuration.h
Unescape View File

@ -1,220 +1,243 @@
#ifndef CONFIGURATION_H
#define CONFIGURATION_H
//#define DEBUG_STEPS
// BASIC SETTINGS: select your board type, thermistor type, axis scaling, and endstop configuration
//// The following define selects which electronics board you have. Please choose the one that matches your setup
// MEGA/RAMPS up to 1.2 = 3,
// RAMPS 1.3 = 33
// Gen6 = 5,
// Sanguinololu 1.2 and above = 62
// Ultimaker = 7,
#define MOTHERBOARD 7
//#define MOTHERBOARD 5
//// Thermistor settings:
// 1 is 100k thermistor
// 2 is 200k thermistor
// 3 is mendel-parts thermistor
// 4 is 10k thermistor
// 5 is ParCan supplied 104GT-2 100K
// 6 is EPCOS 100k
// 7 is 100k Honeywell thermistor 135-104LAG-J01
#define THERMISTORHEATER_1 3
#define THERMISTORHEATER_2 3
#define THERMISTORBED 3
//#define HEATER_1_USES_THERMISTOR
//#define HEATER_2_USES_THERMISTOR
#define HEATER_1_USES_AD595
//#define HEATER_2_USES_AD595
// Select one of these only to define how the bed temp is read.
//#define BED_USES_THERMISTOR
//#define BED_USES_AD595
#define HEATER_CHECK_INTERVAL 50
#define BED_CHECK_INTERVAL 5000
//// Endstop Settings
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
const bool ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
// For optos H21LOB set to true, for Mendel-Parts newer optos TCST2103 set to false
// This determines the communication speed of the printer
//#define BAUDRATE 250000
#define BAUDRATE 115200
//#define BAUDRATE 230400
// Comment out (using // at the start of the line) to disable SD support:
// #define ULTRA_LCD //any lcd
#define LCD_WIDTH 16
#define LCD_HEIGHT 2
//#define ULTIPANEL
#ifdef ULTIPANEL
//#define NEWPANEL //enable this if you have a click-encoder panel
#define SDSUPPORT
#define ULTRA_LCD
#define LCD_WIDTH 20
#define LCD_HEIGHT 4
#endif
//#define SDSUPPORT // Enable SD Card Support in Hardware Console
const int dropsegments=5; //everything with this number of steps will be ignored as move
//// ADVANCED SETTINGS - to tweak parameters
#include "thermistortables.h"
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
#define X_ENABLE_ON 0
#define Y_ENABLE_ON 0
#define Z_ENABLE_ON 0
#define E_ENABLE_ON 0
// Disables axis when it's not being used.
#define DISABLE_X false
#define DISABLE_Y false
#define DISABLE_Z false
#define DISABLE_E false
// Inverting axis direction
#define INVERT_X_DIR true // for Mendel set to false, for Orca set to true
#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true
#define INVERT_E_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
//// ENDSTOP SETTINGS:
// Sets direction of endstops when homing; 1=MAX, -1=MIN
#define X_HOME_DIR -1
#define Y_HOME_DIR -1
#define Z_HOME_DIR -1
#define min_software_endstops false //If true, axis won't move to coordinates less than zero.
#define max_software_endstops false //If true, axis won't move to coordinates greater than the defined lengths below.
#define X_MAX_LENGTH 210
#define Y_MAX_LENGTH 210
#define Z_MAX_LENGTH 210
//// MOVEMENT SETTINGS
#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
//note: on bernhards ultimaker 200 200 12 are working well.
#define HOMING_FEEDRATE {50*60, 50*60, 12*60, 0} // set the homing speeds
//the followint checks if an extrusion is existent in the move. if _not_, the speed of the move is set to the maximum speed.
//!!!!!!Use only if you know that your printer works at the maximum declared speeds.
// works around the skeinforge cool-bug. There all moves are slowed to have a minimum layer time. However slow travel moves= ooze
#define TRAVELING_AT_MAXSPEED
#define AXIS_RELATIVE_MODES {false, false, false, false}
#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
// default settings
#define DEFAULT_AXIS_STEPS_PER_UNIT {79.87220447,79.87220447,200*8/3,14} // default steps per unit for ultimaker
#define DEFAULT_MAX_FEEDRATE {160*60, 160*60, 10*60, 500000}
#define DEFAULT_MAX_ACCELERATION {9000,9000,150,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION 7000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts
#define DEFAULT_MINIMUMFEEDRATE 10 // minimum feedrate
#define DEFAULT_MINTRAVELFEEDRATE 10
// minimum time in microseconds that a movement needs to take if the buffer is emptied. Increase this number if you see blobs while printing high speed & high detail. It will slowdown on the detailed stuff.
#define DEFAULT_MINSEGMENTTIME 20000
#define DEFAULT_XYJERK 30.0*60
#define DEFAULT_ZJERK 10.0*60
// The watchdog waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature
//this enables the watchdog interrupt.
#define USE_WATCHDOG
//you cannot reboot on a mega2560 due to a bug in he bootloader. Hence, you have to reset manually, and this is done hereby:
#define RESET_MANUAL
#define WATCHDOG_TIMEOUT 4
//// Experimental watchdog and minimal temp
// The watchdog waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature
// If the temperature has not increased at the end of that period, the target temperature is set to zero. It can be reset with another M104/M109
//#define WATCHPERIOD 5000 //5 seconds
// Actual temperature must be close to target for this long before M109 returns success
//#define TEMP_RESIDENCY_TIME 20 // (seconds)
//#define TEMP_HYSTERESIS 5 // (C°) range of +/- temperatures considered "close" to the target one
//// The minimal temperature defines the temperature below which the heater will not be enabled
#define MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
// You should use MINTEMP for thermistor short/failure protection.
#define MAXTEMP 275
#define BED_MAXTEMP 150
/// PID settings:
// Uncomment the following line to enable PID support.
//#define SMOOTHING
//#define SMOOTHFACTOR 5.0
//float current_raw_average=0;
#define PIDTEMP
#ifdef PIDTEMP
//#define PID_DEBUG // Sends debug data to the serial port.
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104 sets the output power in %
#define PID_MAX 255 // limits current to nozzle
#define PID_INTEGRAL_DRIVE_MAX 255
#define PID_dT 0.10 // 100ms sample time
#define DEFAULT_Kp 20.0
#define DEFAULT_Ki 1.5*PID_dT
#define DEFAULT_Kd 80/PID_dT
#define DEFAULT_Kc 0
#endif // PIDTEMP
// extruder advance constant (s2/mm3)
//
// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTUDER_ADVANCE_K * cubic mm per second ^ 2
//
// hooke's law says: force = k * distance
// bernoulli's priniciple says: v ^ 2 / 2 + g . h + pressure / density = constant
// so: v ^ 2 is proportional to number of steps we advance the extruder
//#define ADVANCE
#ifdef ADVANCE
#define EXTRUDER_ADVANCE_K .3
#define D_FILAMENT 1.7
#define STEPS_MM_E 65
#define EXTRUTION_AREA (0.25 * D_FILAMENT * D_FILAMENT * 3.14159)
#define STEPS_PER_CUBIC_MM_E (axis_steps_per_unit[E_AXIS]/ EXTRUTION_AREA)
#endif // ADVANCE
#if defined SDSUPPORT
// The number of linear motions that can be in the plan at any give time.
#define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
#else
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer
#endif
#ifdef SIMPLE_LCD
#define BLOCK_BUFFER_SIZE 16 // A little less buffer for just a simple LCD
#endif
#endif
#ifndef CONFIGURATION_H
#define CONFIGURATION_H
//#define DEBUG_STEPS
// BASIC SETTINGS: select your board type, thermistor type, axis scaling, and endstop configuration
//// The following define selects which electronics board you have. Please choose the one that matches your setup
// MEGA/RAMPS up to 1.2 = 3,
// RAMPS 1.3 = 33
// Gen6 = 5,
// Sanguinololu 1.2 and above = 62
// Ultimaker = 7,
#define MOTHERBOARD 7
//#define MOTHERBOARD 5
//// Thermistor settings:
// 1 is 100k thermistor
// 2 is 200k thermistor
// 3 is mendel-parts thermistor
// 4 is 10k thermistor
// 5 is ParCan supplied 104GT-2 100K
// 6 is EPCOS 100k
// 7 is 100k Honeywell thermistor 135-104LAG-J01
#define THERMISTORHEATER_1 3
#define THERMISTORHEATER_2 3
#define THERMISTORBED 3
//#define HEATER_1_USES_THERMISTOR
//#define HEATER_2_USES_THERMISTOR
#define HEATER_1_USES_AD595
//#define HEATER_2_USES_AD595
// Select one of these only to define how the bed temp is read.
//#define BED_USES_THERMISTOR
//#define BED_USES_AD595
#define HEATER_CHECK_INTERVAL 50
#define BED_CHECK_INTERVAL 5000
//// Endstop Settings
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
const bool ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
// For optos H21LOB set to true, for Mendel-Parts newer optos TCST2103 set to false
// This determines the communication speed of the printer
//#define BAUDRATE 250000
#define BAUDRATE 115200
//#define BAUDRATE 230400
// Comment out (using // at the start of the line) to disable SD support:
// #define ULTRA_LCD //any lcd
#define ULTIPANEL
#ifdef ULTIPANEL
//#define NEWPANEL //enable this if you have a click-encoder panel
#define SDSUPPORT
#define ULTRA_LCD
#define LCD_WIDTH 20
#define LCD_HEIGHT 4
#else //no panel but just lcd
#ifdef ULTRA_LCD
#define LCD_WIDTH 16
#define LCD_HEIGHT 2
#endif
#endif
//#define SDSUPPORT // Enable SD Card Support in Hardware Console
const int dropsegments=5; //everything with this number of steps will be ignored as move
//// ADVANCED SETTINGS - to tweak parameters
#include "thermistortables.h"
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
#define X_ENABLE_ON 0
#define Y_ENABLE_ON 0
#define Z_ENABLE_ON 0
#define E_ENABLE_ON 0
// Disables axis when it's not being used.
#define DISABLE_X false
#define DISABLE_Y false
#define DISABLE_Z false
#define DISABLE_E false
// Inverting axis direction
#define INVERT_X_DIR true // for Mendel set to false, for Orca set to true
#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true
#define INVERT_E_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
//// ENDSTOP SETTINGS:
// Sets direction of endstops when homing; 1=MAX, -1=MIN
#define X_HOME_DIR -1
#define Y_HOME_DIR -1
#define Z_HOME_DIR -1
#define min_software_endstops false //If true, axis won't move to coordinates less than zero.
#define max_software_endstops false //If true, axis won't move to coordinates greater than the defined lengths below.
#define X_MAX_LENGTH 210
#define Y_MAX_LENGTH 210
#define Z_MAX_LENGTH 210
//// MOVEMENT SETTINGS
#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
//note: on bernhards ultimaker 200 200 12 are working well.
#define HOMING_FEEDRATE {50*60, 50*60, 12*60, 0} // set the homing speeds
//the followint checks if an extrusion is existent in the move. if _not_, the speed of the move is set to the maximum speed.
//!!!!!!Use only if you know that your printer works at the maximum declared speeds.
// works around the skeinforge cool-bug. There all moves are slowed to have a minimum layer time. However slow travel moves= ooze
#define TRAVELING_AT_MAXSPEED
#define AXIS_RELATIVE_MODES {false, false, false, false}
#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
// default settings
#define DEFAULT_AXIS_STEPS_PER_UNIT {79.87220447,79.87220447,200*8/3,14} // default steps per unit for ultimaker
#define DEFAULT_MAX_FEEDRATE {160*60, 160*60, 10*60, 500000}
#define DEFAULT_MAX_ACCELERATION {9000,9000,150,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION 7000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts
#define DEFAULT_MINIMUMFEEDRATE 10 // minimum feedrate
#define DEFAULT_MINTRAVELFEEDRATE 10
// minimum time in microseconds that a movement needs to take if the buffer is emptied. Increase this number if you see blobs while printing high speed & high detail. It will slowdown on the detailed stuff.
#define DEFAULT_MINSEGMENTTIME 20000
#define DEFAULT_XYJERK 30.0*60
#define DEFAULT_ZJERK 10.0*60
// The watchdog waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature
//this enables the watchdog interrupt.
#define USE_WATCHDOG
//you cannot reboot on a mega2560 due to a bug in he bootloader. Hence, you have to reset manually, and this is done hereby:
#define RESET_MANUAL
#define WATCHDOG_TIMEOUT 4
//// Experimental watchdog and minimal temp
// The watchdog waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature
// If the temperature has not increased at the end of that period, the target temperature is set to zero. It can be reset with another M104/M109
//#define WATCHPERIOD 5000 //5 seconds
// Actual temperature must be close to target for this long before M109 returns success
//#define TEMP_RESIDENCY_TIME 20 // (seconds)
//#define TEMP_HYSTERESIS 5 // (C°) range of +/- temperatures considered "close" to the target one
//// The minimal temperature defines the temperature below which the heater will not be enabled
#define MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
// You should use MINTEMP for thermistor short/failure protection.
#define MAXTEMP 275
#define BED_MAXTEMP 150
#define PIDTEMP
#ifdef PIDTEMP
/// PID settings:
// Uncomment the following line to enable PID support.
//#define SMOOTHING
//#define SMOOTHFACTOR 5.0
//float current_raw_average=0;
#define K1 0.95 //smoothing of the PID
//#define PID_DEBUG // Sends debug data to the serial port.
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104 sets the output power in %
#define PID_MAX 255 // limits current to nozzle
#define PID_INTEGRAL_DRIVE_MAX 255
#define PID_dT 0.1
//machine with red silicon: 1950:45 second ; with fan fully blowin 3000:47
#define PID_CRITIAL_GAIN 3000
#define PID_SWING_AT_CRITIAL 45 //seconds
#define PIDIADD 5
/*
//PID according to Ziegler-Nichols method
float Kp = 0.6*PID_CRITIAL_GAIN;
float Ki =PIDIADD+2*Kp/PID_SWING_AT_CRITIAL*PID_dT;
float Kd = Kp*PID_SWING_AT_CRITIAL/8./PID_dT;
*/
//PI according to Ziegler-Nichols method
#define DEFAULT_Kp (PID_CRITIAL_GAIN/2.2)
#define DEFAULT_Ki (1.2*Kp/PID_SWING_AT_CRITIAL*PID_dT)
#define DEFAULT_Kd (0)
#define PID_ADD_EXTRUSION_RATE
#ifdef PID_ADD_EXTRUSION_RATE
#define DEFAULT_Kc (5) //heatingpower=Kc*(e_speed)
#endif
#endif // PIDTEMP
// extruder advance constant (s2/mm3)
//
// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTUDER_ADVANCE_K * cubic mm per second ^ 2
//
// hooke's law says: force = k * distance
// bernoulli's priniciple says: v ^ 2 / 2 + g . h + pressure / density = constant
// so: v ^ 2 is proportional to number of steps we advance the extruder
//#define ADVANCE
#ifdef ADVANCE
#define EXTRUDER_ADVANCE_K .3
#define D_FILAMENT 1.7
#define STEPS_MM_E 65
#define EXTRUTION_AREA (0.25 * D_FILAMENT * D_FILAMENT * 3.14159)
#define STEPS_PER_CUBIC_MM_E (axis_steps_per_unit[E_AXIS]/ EXTRUTION_AREA)
#endif // ADVANCE
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, e.g. 8,16,32
#if defined SDSUPPORT
// The number of linear motions that can be in the plan at any give time.
#define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
#else
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer
#endif
#endif

252
Marlin/EEPROM.h → Marlin/EEPROMwrite.h
Unescape View File

@ -1,123 +1,129 @@
#include "planner.h"
#include "temperature.h"
//======================================================================================
template <class T> int EEPROM_writeAnything(int &ee, const T& value)
{
const byte* p = (const byte*)(const void*)&value;
int i;
for (i = 0; i < sizeof(value); i++)
EEPROM.write(ee++, *p++);
return i;
}
//======================================================================================
template <class T> int EEPROM_readAnything(int &ee, T& value)
{
byte* p = (byte*)(void*)&value;
int i;
for (i = 0; i < sizeof(value); i++)
*p++ = EEPROM.read(ee++);
return i;
}
//======================================================================================
#define EEPROM_OFFSET 100
#define EEPROM_VERSION "V04" // IMPORTANT: Whenever there are changes made to the variables stored in EEPROM
// in the functions below, also increment the version number. This makes sure that
// the default values are used whenever there is a change to the data, to prevent
// wrong data being written to the variables.
// ALSO: always make sure the variables in the Store and retrieve sections are in the same order.
void StoreSettings() {
char ver[4]= "000";
int i=EEPROM_OFFSET;
EEPROM_writeAnything(i,ver); // invalidate data first
EEPROM_writeAnything(i,axis_steps_per_unit);
EEPROM_writeAnything(i,max_feedrate);
EEPROM_writeAnything(i,max_acceleration_units_per_sq_second);
EEPROM_writeAnything(i,acceleration);
EEPROM_writeAnything(i,retract_acceleration);
EEPROM_writeAnything(i,minimumfeedrate);
EEPROM_writeAnything(i,mintravelfeedrate);
EEPROM_writeAnything(i,minsegmenttime);
EEPROM_writeAnything(i,max_xy_jerk);
EEPROM_writeAnything(i,max_z_jerk);
#ifdef PIDTEMP
EEPROM_writeAnything(i,Kp);
EEPROM_writeAnything(i,Ki);
EEPROM_writeAnything(i,Kd);
#else
EEPROM_writeAnything(i,3000);
EEPROM_writeAnything(i,0);
EEPROM_writeAnything(i,0);
#endif
char ver2[4]=EEPROM_VERSION;
i=EEPROM_OFFSET;
EEPROM_writeAnything(i,ver2); // validate data
ECHOLN("Settings Stored");
}
void RetrieveSettings(bool def=false){ // if def=true, the default values will be used
int i=EEPROM_OFFSET;
char stored_ver[4];
char ver[4]=EEPROM_VERSION;
EEPROM_readAnything(i,stored_ver); //read stored version
// ECHOLN("Version: [" << ver << "] Stored version: [" << stored_ver << "]");
if ((!def)&&(strncmp(ver,stored_ver,3)==0)) { // version number match
EEPROM_readAnything(i,axis_steps_per_unit);
EEPROM_readAnything(i,max_feedrate);
EEPROM_readAnything(i,max_acceleration_units_per_sq_second);
EEPROM_readAnything(i,acceleration);
EEPROM_readAnything(i,retract_acceleration);
EEPROM_readAnything(i,minimumfeedrate);
EEPROM_readAnything(i,mintravelfeedrate);
EEPROM_readAnything(i,minsegmenttime);
EEPROM_readAnything(i,max_xy_jerk);
EEPROM_readAnything(i,max_z_jerk);
#ifndef PIDTEMP
float Kp,Ki,Kd;
#endif
EEPROM_readAnything(i,Kp);
EEPROM_readAnything(i,Ki);
EEPROM_readAnything(i,Kd);
ECHOLN("Stored settings retreived:");
}
else {
float tmp1[]=DEFAULT_AXIS_STEPS_PER_UNIT;
float tmp2[]=DEFAULT_MAX_FEEDRATE;
long tmp3[]=DEFAULT_MAX_ACCELERATION;
for (int i=0;i<4;i++) {
axis_steps_per_unit[i]=tmp1[i];
max_feedrate[i]=tmp2[i];
max_acceleration_units_per_sq_second[i]=tmp3[i];
}
acceleration=DEFAULT_ACCELERATION;
retract_acceleration=DEFAULT_RETRACT_ACCELERATION;
minimumfeedrate=DEFAULT_MINIMUMFEEDRATE;
minsegmenttime=DEFAULT_MINSEGMENTTIME;
mintravelfeedrate=DEFAULT_MINTRAVELFEEDRATE;
max_xy_jerk=DEFAULT_XYJERK;
max_z_jerk=DEFAULT_ZJERK;
ECHOLN("Using Default settings:");
}
ECHOLN("Steps per unit:");
ECHOLN(" M92 X" <<_FLOAT(axis_steps_per_unit[0],3) << " Y" << _FLOAT(axis_steps_per_unit[1],3) << " Z" << _FLOAT(axis_steps_per_unit[2],3) << " E" << _FLOAT(axis_steps_per_unit[3],3));
ECHOLN("Maximum feedrates (mm/s):");
ECHOLN(" M203 X" <<_FLOAT(max_feedrate[0]/60,2)<<" Y" << _FLOAT(max_feedrate[1]/60,2) << " Z" << _FLOAT(max_feedrate[2]/60,2) << " E" << _FLOAT(max_feedrate[3]/60,2));
ECHOLN("Maximum Acceleration (mm/s2):");
ECHOLN(" M201 X" <<_FLOAT(max_acceleration_units_per_sq_second[0],0) << " Y" << _FLOAT(max_acceleration_units_per_sq_second[1],0) << " Z" << _FLOAT(max_acceleration_units_per_sq_second[2],0) << " E" << _FLOAT(max_acceleration_units_per_sq_second[3],0));
ECHOLN("Acceleration: S=acceleration, T=retract acceleration");
ECHOLN(" M204 S" <<_FLOAT(acceleration,2) << " T" << _FLOAT(retract_acceleration,2));
ECHOLN("Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum xY jerk (mm/s), Z=maximum Z jerk (mm/s)");
ECHOLN(" M205 S" <<_FLOAT(minimumfeedrate/60,2) << " T" << _FLOAT(mintravelfeedrate/60,2) << " B" << _FLOAT(minsegmenttime,2) << " X" << _FLOAT(max_xy_jerk/60,2) << " Z" << _FLOAT(max_z_jerk/60,2));
#ifdef PIDTEMP
ECHOLN("PID settings:");
ECHOLN(" M301 P" << _FLOAT(Kp,3) << " I" << _FLOAT(Ki,3) << " D" << _FLOAT(Kd,3));
#endif
}
#ifndef __EEPROMH
#define __EEPROMH
#include "planner.h"
#include "temperature.h"
#include <EEPROM.h>
#include "Marlin.h"
#include "streaming.h"
//======================================================================================
template <class T> int EEPROM_writeAnything(int &ee, const T& value)
{
const byte* p = (const byte*)(const void*)&value;
int i;
for (i = 0; i < (int)sizeof(value); i++)
EEPROM.write(ee++, *p++);
return i;
}
//======================================================================================
template <class T> int EEPROM_readAnything(int &ee, T& value)
{
byte* p = (byte*)(void*)&value;
int i;
for (i = 0; i < (int)sizeof(value); i++)
*p++ = EEPROM.read(ee++);
return i;
}
//======================================================================================
#define EEPROM_OFFSET 100
#define EEPROM_VERSION "V04" // IMPORTANT: Whenever there are changes made to the variables stored in EEPROM
// in the functions below, also increment the version number. This makes sure that
// the default values are used whenever there is a change to the data, to prevent
// wrong data being written to the variables.
// ALSO: always make sure the variables in the Store and retrieve sections are in the same order.
void StoreSettings() {
char ver[4]= "000";
int i=EEPROM_OFFSET;
EEPROM_writeAnything(i,ver); // invalidate data first
EEPROM_writeAnything(i,axis_steps_per_unit);
EEPROM_writeAnything(i,max_feedrate);
EEPROM_writeAnything(i,max_acceleration_units_per_sq_second);
EEPROM_writeAnything(i,acceleration);
EEPROM_writeAnything(i,retract_acceleration);
EEPROM_writeAnything(i,minimumfeedrate);
EEPROM_writeAnything(i,mintravelfeedrate);
EEPROM_writeAnything(i,minsegmenttime);
EEPROM_writeAnything(i,max_xy_jerk);
EEPROM_writeAnything(i,max_z_jerk);
#ifdef PIDTEMP
EEPROM_writeAnything(i,Kp);
EEPROM_writeAnything(i,Ki);
EEPROM_writeAnything(i,Kd);
#else
EEPROM_writeAnything(i,3000);
EEPROM_writeAnything(i,0);
EEPROM_writeAnything(i,0);
#endif
char ver2[4]=EEPROM_VERSION;
i=EEPROM_OFFSET;
EEPROM_writeAnything(i,ver2); // validate data
ECHOLN("Settings Stored");
}
void RetrieveSettings(bool def=false){ // if def=true, the default values will be used
int i=EEPROM_OFFSET;
char stored_ver[4];
char ver[4]=EEPROM_VERSION;
EEPROM_readAnything(i,stored_ver); //read stored version
// ECHOLN("Version: [" << ver << "] Stored version: [" << stored_ver << "]");
if ((!def)&&(strncmp(ver,stored_ver,3)==0)) { // version number match
EEPROM_readAnything(i,axis_steps_per_unit);
EEPROM_readAnything(i,max_feedrate);
EEPROM_readAnything(i,max_acceleration_units_per_sq_second);
EEPROM_readAnything(i,acceleration);
EEPROM_readAnything(i,retract_acceleration);
EEPROM_readAnything(i,minimumfeedrate);
EEPROM_readAnything(i,mintravelfeedrate);
EEPROM_readAnything(i,minsegmenttime);
EEPROM_readAnything(i,max_xy_jerk);
EEPROM_readAnything(i,max_z_jerk);
#ifndef PIDTEMP
float Kp,Ki,Kd;
#endif
EEPROM_readAnything(i,Kp);
EEPROM_readAnything(i,Ki);
EEPROM_readAnything(i,Kd);
ECHOLN("Stored settings retreived:");
}
else {
float tmp1[]=DEFAULT_AXIS_STEPS_PER_UNIT;
float tmp2[]=DEFAULT_MAX_FEEDRATE;
long tmp3[]=DEFAULT_MAX_ACCELERATION;
for (int i=0;i<4;i++) {
axis_steps_per_unit[i]=tmp1[i];
max_feedrate[i]=tmp2[i];
max_acceleration_units_per_sq_second[i]=tmp3[i];
}
acceleration=DEFAULT_ACCELERATION;
retract_acceleration=DEFAULT_RETRACT_ACCELERATION;
minimumfeedrate=DEFAULT_MINIMUMFEEDRATE;
minsegmenttime=DEFAULT_MINSEGMENTTIME;
mintravelfeedrate=DEFAULT_MINTRAVELFEEDRATE;
max_xy_jerk=DEFAULT_XYJERK;
max_z_jerk=DEFAULT_ZJERK;
ECHOLN("Using Default settings:");
}
ECHOLN("Steps per unit:");
ECHOLN(" M92 X" <<_FLOAT(axis_steps_per_unit[0],3) << " Y" << _FLOAT(axis_steps_per_unit[1],3) << " Z" << _FLOAT(axis_steps_per_unit[2],3) << " E" << _FLOAT(axis_steps_per_unit[3],3));
ECHOLN("Maximum feedrates (mm/s):");
ECHOLN(" M203 X" <<_FLOAT(max_feedrate[0]/60,2)<<" Y" << _FLOAT(max_feedrate[1]/60,2) << " Z" << _FLOAT(max_feedrate[2]/60,2) << " E" << _FLOAT(max_feedrate[3]/60,2));
ECHOLN("Maximum Acceleration (mm/s2):");
ECHOLN(" M201 X" <<_FLOAT(max_acceleration_units_per_sq_second[0],0) << " Y" << _FLOAT(max_acceleration_units_per_sq_second[1],0) << " Z" << _FLOAT(max_acceleration_units_per_sq_second[2],0) << " E" << _FLOAT(max_acceleration_units_per_sq_second[3],0));
ECHOLN("Acceleration: S=acceleration, T=retract acceleration");
ECHOLN(" M204 S" <<_FLOAT(acceleration,2) << " T" << _FLOAT(retract_acceleration,2));
ECHOLN("Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum xY jerk (mm/s), Z=maximum Z jerk (mm/s)");
ECHOLN(" M205 S" <<_FLOAT(minimumfeedrate/60,2) << " T" << _FLOAT(mintravelfeedrate/60,2) << " B" << _FLOAT(minsegmenttime,2) << " X" << _FLOAT(max_xy_jerk/60,2) << " Z" << _FLOAT(max_z_jerk/60,2));
#ifdef PIDTEMP
ECHOLN("PID settings:");
ECHOLN(" M301 P" << _FLOAT(Kp,3) << " I" << _FLOAT(Ki,3) << " D" << _FLOAT(Kd,3));
#endif
}
#endif

582
Marlin/Makefile
Unescape View File

@ -1,274 +1,320 @@
TARGET = $(notdir $(CURDIR))
# CHANGE BELOW:
#~ INSTALL_DIR = /Applications/Arduino.app/Contents/Resources/Java
INSTALL_DIR = /home/bkubicek/software/arduino-0022
#~ PORT = /dev/cu.usbserial*
PORT = /dev/ttyACM0
# Get these values from:
# $(INSTALL_DIR)/hardware/boards.txt
# (arduino-0022/hardware/arduino/boards.txt)
# The values below are for the "Arduino Duemilanove or Nano w/ ATmega328"
# now for "Arduino Mega 2560"
UPLOAD_SPEED = 115200
UPLOAD_PROTOCOL = stk500v2
BUILD_MCU = atmega2560
BUILD_F_CPU = 16000000L
# getting undefined reference to `__cxa_pure_virtual'
#~ [http://www.arduino.cc/cgi-bin/yabb2/YaBB.pl?num=1254180518 Arduino Forum - Makefile]
#~ http://www.arduino.cc/playground/OpenBSD/CLI
#~ [http://arduino.cc/forum/index.php?topic=52041.0 A "simple" makefile for Arduino]
#~ [http://www.arduino.cc/cgi-bin/yabb2/YaBB.pl?num=1275488191 Arduino Forum - Configuring avr-gcc options in arduino IDE]
# found in /usr/lib/gcc/avr/4.3.5/cc1plus; fixed with -Wl,--gc-section
############################################################################
# Below here nothing should be changed...
ARDUINO = $(INSTALL_DIR)/hardware/arduino/cores/arduino
#
# Arduino 0022 Makefile
# Uno with DOGS102 Shield
#~ AVR_TOOLS_PATH = $(INSTALL_DIR)/hardware/tools/avr/bin
# in Ubuntu, avr-gcc is installed separate;
# only avrdude comes with the IDE
AVR_TOOLS_PATH = /usr/bin
AVR_DUDE_PATH = $(INSTALL_DIR)/hardware/tools
#
# written by olikraus@gmail.com
#
# Features:
# - boards.txt is used to derive parameters
# - All intermediate files are put into a separate directory (TMPDIRNAME)
# - Simple use: Copy Makefile into the same directory of the .pde file
#
# Limitations:
# - requires UNIX environment
# - TMPDIRNAME must be subdirectory of the current directory.
#
# Targets
# all build everything
# upload build and upload to arduino
# clean remove all temporary files (includes final hex file)
#
# History
# 001 28 Apr 2010 first release
# 002 05 Oct 2010 added 'uno'
#
#=== user configuration ===
# All ...PATH variables must have a '/' at the end
# Board (and prozessor) information: see $(ARDUINO_PATH)hardware/arduino/boards.txt
# Some examples:
# BOARD DESCRIPTION
# uno Arduino Uno
# atmega328 Arduino Duemilanove or Nano w/ ATmega328
# diecimila Arduino Diecimila, Duemilanove, or Nano w/ ATmega168
# mega Arduino Mega
# mini Arduino Mini
# lilypad328 LilyPad Arduino w/ ATmega328
BOARD:=mega
# additional (comma separated) defines
# -DDOGM128_HW board is connected to DOGM128 display
# -DDOGM132_HW board is connected to DOGM132 display
# -DDOGS102_HW board is connected to DOGS102 display
# -DDOG_REVERSE 180 degree rotation
# -DDOG_SPI_SW_ARDUINO force SW shiftOut
DEFS=-DDOGS102_HW -DDOG_DOUBLE_MEMORY -DDOG_SPI_SW_ARDUINO
# The location where the avr tools (e.g. avr-gcc) are located. Requires a '/' at the end.
# Can be empty if all tools are accessable through the search path
AVR_TOOLS_PATH:=/usr/bin/
# Install path of the arduino software. Requires a '/' at the end.
ARDUINO_PATH:=/home/bkubicek/software/arduino-0022/
# Install path for avrdude. Requires a '/' at the end. Can be empty if avrdude is in the search path.
AVRDUDE_PATH:=
# The unix device where we can reach the arduino board
# Uno: /dev/ttyACM0
# Duemilanove: /dev/ttyUSB0
AVRDUDE_PORT:=/dev/ttyACM0
# List of all libaries which should be included.
#EXTRA_DIRS=$(ARDUINO_PATH)libraries/LiquidCrystal/
#EXTRA_DIRS+=$(ARDUINO_PATH)libraries/Dogm/
#EXTRA_DIRS+=/home/kraus/src/arduino/dogm128/hg/libraries/Dogm/
#=== fetch parameter from boards.txt processor parameter ===
# the basic idea is to get most of the information from boards.txt
BOARDS_TXT:=$(ARDUINO_PATH)hardware/arduino/boards.txt
# get the MCU value from the $(BOARD).build.mcu variable. For the atmega328 board this is atmega328p
MCU:=$(shell sed -n -e "s/$(BOARD).build.mcu=\(.*\)/\1/p" $(BOARDS_TXT))
# get the F_CPU value from the $(BOARD).build.f_cpu variable. For the atmega328 board this is 16000000
F_CPU:=$(shell sed -n -e "s/$(BOARD).build.f_cpu=\(.*\)/\1/p" $(BOARDS_TXT))
# avrdude
# get the AVRDUDE_UPLOAD_RATE value from the $(BOARD).upload.speed variable. For the atmega328 board this is 57600
AVRDUDE_UPLOAD_RATE:=$(shell sed -n -e "s/$(BOARD).upload.speed=\(.*\)/\1/p" $(BOARDS_TXT))
# get the AVRDUDE_PROGRAMMER value from the $(BOARD).upload.protocol variable. For the atmega328 board this is stk500
# AVRDUDE_PROGRAMMER:=$(shell sed -n -e "s/$(BOARD).upload.protocol=\(.*\)/\1/p" $(BOARDS_TXT))
# use stk500v1, because stk500 will default to stk500v2
AVRDUDE_PROGRAMMER:=stk500v1
#=== identify user files ===
PDESRC:=$(shell ls *.pde)
TARGETNAME=$(basename $(PDESRC))
CDIRS:=$(EXTRA_DIRS) $(addsuffix utility/,$(EXTRA_DIRS))
CDIRS:=*.c utility/*.c $(addsuffix *.c,$(CDIRS)) $(ARDUINO_PATH)hardware/arduino/cores/arduino/*.c
CSRC:=$(shell ls $(CDIRS) 2>/dev/null)
CCSRC:=$(shell ls *.cc 2>/dev/null)
CPPDIRS:=$(EXTRA_DIRS) $(addsuffix utility/,$(EXTRA_DIRS))
CPPDIRS:=*.cpp utility/*.cpp $(addsuffix *.cpp,$(CPPDIRS)) $(ARDUINO_PATH)hardware/arduino/cores/arduino/*.cpp
CPPSRC:=$(shell ls $(CPPDIRS) 2>/dev/null)
#=== build internal variables ===
# the name of the subdirectory where everything is stored
TMPDIRNAME:=tmp
TMPDIRPATH:=$(TMPDIRNAME)/
AVRTOOLSPATH:=$(AVR_TOOLS_PATH)
OBJCOPY:=$(AVRTOOLSPATH)avr-objcopy
OBJDUMP:=$(AVRTOOLSPATH)avr-objdump
SIZE:=$(AVRTOOLSPATH)avr-size
CPPSRC:=$(addprefix $(TMPDIRPATH),$(PDESRC:.pde=.cpp)) $(CPPSRC)
COBJ:=$(CSRC:.c=.o)
CCOBJ:=$(CCSRC:.cc=.o)
CPPOBJ:=$(CPPSRC:.cpp=.o)
OBJFILES:=$(COBJ) $(CCOBJ) $(CPPOBJ)
DIRS:= $(dir $(OBJFILES))
DEPFILES:=$(OBJFILES:.o=.d)
# assembler files from avr-gcc -S
ASSFILES:=$(OBJFILES:.o=.s)
# disassembled object files with avr-objdump -S
DISFILES:=$(OBJFILES:.o=.dis)
LIBNAME:=$(TMPDIRPATH)$(TARGETNAME).a
ELFNAME:=$(TMPDIRPATH)$(TARGETNAME).elf
HEXNAME:=$(TMPDIRPATH)$(TARGETNAME).hex
AVRDUDE_FLAGS = -V -F
AVRDUDE_FLAGS += -C $(ARDUINO_PATH)/hardware/tools/avrdude.conf
AVRDUDE_FLAGS += -p $(MCU)
AVRDUDE_FLAGS += -P $(AVRDUDE_PORT)
AVRDUDE_FLAGS += -c $(AVRDUDE_PROGRAMMER)
AVRDUDE_FLAGS += -b $(AVRDUDE_UPLOAD_RATE)
AVRDUDE_FLAGS += -U flash:w:$(HEXNAME)
AVRDUDE = avrdude
#=== predefined variable override ===
# use "make -p -f/dev/null" to see the default rules and definitions
# Build C and C++ flags. Include path information must be placed here
COMMON_FLAGS = -DF_CPU=$(F_CPU) -mmcu=$(MCU) $(DEFS)
# COMMON_FLAGS += -gdwarf-2
COMMON_FLAGS += -Os
COMMON_FLAGS += -Wall -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums
COMMON_FLAGS += -I.
COMMON_FLAGS += -I$(ARDUINO_PATH)hardware/arduino/cores/arduino
COMMON_FLAGS += $(addprefix -I,$(EXTRA_DIRS))
COMMON_FLAGS += -ffunction-sections -fdata-sections -Wl,--gc-sections
COMMON_FLAGS += -Wl,--relax
COMMON_FLAGS += -mcall-prologues
CFLAGS = $(COMMON_FLAGS) -std=gnu99 -Wstrict-prototypes
CXXFLAGS = $(COMMON_FLAGS)
# Replace standard build tools by avr tools
CC = $(AVRTOOLSPATH)avr-gcc
CXX = $(AVRTOOLSPATH)avr-g++
AR = @$(AVRTOOLSPATH)avr-ar
# "rm" must be able to delete a directory tree
RM = rm -rf
#=== rules ===
# add rules for the C/C++ files where the .o file is placed in the TMPDIRPATH
# reuse existing variables as far as possible
$(TMPDIRPATH)%.o: %.c
@echo compile $<
@$(COMPILE.c) $(OUTPUT_OPTION) $<
$(TMPDIRPATH)%.o: %.cc
@echo compile $<
@$(COMPILE.cc) $(OUTPUT_OPTION) $<
$(TMPDIRPATH)%.o: %.cpp
@echo compile $<
@$(COMPILE.cpp) $(OUTPUT_OPTION) $<
$(TMPDIRPATH)%.s: %.c
@$(COMPILE.c) $(OUTPUT_OPTION) -S $<
$(TMPDIRPATH)%.s: %.cc
@$(COMPILE.cc) $(OUTPUT_OPTION) -S $<
$(TMPDIRPATH)%.s: %.cpp
@$(COMPILE.cpp) $(OUTPUT_OPTION) -S $<
$(TMPDIRPATH)%.dis: $(TMPDIRPATH)%.o
@$(OBJDUMP) -S $< > $@
.SUFFIXES: .elf .hex .pde
SRC = $(ARDUINO)/pins_arduino.c $(ARDUINO)/wiring.c \
$(ARDUINO)/wiring_analog.c $(ARDUINO)/wiring_digital.c \
$(ARDUINO)/wiring_pulse.c \
$(ARDUINO)/wiring_shift.c $(ARDUINO)/WInterrupts.c
# added applet/$(TARGET).cpp as in IDE 0022
CXXSRC = $(ARDUINO)/HardwareSerial.cpp $(ARDUINO)/WMath.cpp \
$(ARDUINO)/Print.cpp \
$(ARDUINO)/main.cpp
# applet/$(TARGET).cpp # no need, having a rule now for applet/$(TARGET).cpp.o
# added main.cpp, as in 0022
FORMAT = ihex
# Name of this Makefile (used for "make depend").
MAKEFILE = Makefile
# Debugging format.
# Native formats for AVR-GCC's -g are stabs [default], or dwarf-2.
# AVR (extended) COFF requires stabs, plus an avr-objcopy run.
DEBUG = stabs
OPT = 2
# Place -D or -U options here
#~ CDEFS = -DBUILD_F_CPU=$(BUILD_F_CPU)
#~ CXXDEFS = -DBUILD_F_CPU=$(BUILD_F_CPU)
# now called DF_CPU
CDEFS = -DF_CPU=$(BUILD_F_CPU) -DARDUINO=22
CXXDEFS = -DF_CPU=$(BUILD_F_CPU) -DARDUINO=22
# Place -I options here
CINCS = -I$(ARDUINO) -I$(INSTALL_DIR)/libraries/LiquidCrystal/ -I$(INSTALL_DIR)/libraries/EEPROM/
CXXINCS = -I$(ARDUINO)
# Compiler flag to set the C Standard level.
# c89 - "ANSI" C
# gnu89 - c89 plus GCC extensions
# c99 - ISO C99 standard (not yet fully implemented)
# gnu99 - c99 plus GCC extensions
CSTANDARD = -std=gnu99
CDEBUG = -g$(DEBUG)
# note that typically, IDE 0022 uses -w to suppress warnings (both in cpp and c)!
CWARN = -Wall
#~ CWARN = -w
# "-Wstrict-prototypes" is valid for Ada/C/ObjC but not for C++:
CCWARN = -Wstrict-prototypes
CTUNING = -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums
#CEXTRA = -Wa,-adhlns=$(<:.c=.lst)
# to eliminate pins_ardiuno warnings:
# http://arduino.cc/pipermail/developers_arduino.cc/2010-December/004005.html
# [http://www.arduino.cc/cgi-bin/yabb2/YaBB.pl?num=1254180518 Arduino Forum - Makefile]
#~ For building the objects files "-ffunction-sections -fdata-sections" was missing
#~ and the final avr-gcc call needs "-Wl,--gc-section".
CXSECTF = -fno-exceptions -ffunction-sections -fdata-sections
CFINALF = -Wl,--gc-section
CFLAGS = $(CDEBUG) $(CDEFS) $(CINCS) -O$(OPT) $(CWARN) $(CCWARN) $(CSTANDARD) $(CEXTRA)
# added CWARN also to .cpp
CXXFLAGS = $(CDEFS) $(CINCS) -O$(OPT) $(CWARN) $(CXSECTF)
#ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs
LDFLAGS = -lm
# Programming support using avrdude. Settings and variables.
AVRDUDE_PORT = $(PORT)
AVRDUDE_WRITE_FLASH = -U flash:w:applet/$(TARGET).hex
AVRDUDE_FLAGS = -V -F \
-p $(BUILD_MCU) -P $(AVRDUDE_PORT) -c $(UPLOAD_PROTOCOL) \
-b $(UPLOAD_SPEED) -C $(INSTALL_DIR)/hardware/tools/avrdude.conf
# -b $(UPLOAD_SPEED) -C $(INSTALL_DIR)/hardware/tools/avr/etc/avrdude.conf
# Program settings
CC = $(AVR_TOOLS_PATH)/avr-gcc
CXX = $(AVR_TOOLS_PATH)/avr-g++
OBJCOPY = $(AVR_TOOLS_PATH)/avr-objcopy
OBJDUMP = $(AVR_TOOLS_PATH)/avr-objdump
AR = $(AVR_TOOLS_PATH)/avr-ar
SIZE = $(AVR_TOOLS_PATH)/avr-size
NM = $(AVR_TOOLS_PATH)/avr-nm
#~ AVRDUDE = $(AVR_TOOLS_PATH)/avrdude
AVRDUDE = $(AVR_DUDE_PATH)/avrdude
REMOVE = rm -f
MV = mv -f
# Define all object files.
# NOTE: obj files will be created in respective src directories (libraries or $(INSTALL_DIR));
# make clean deletes them fine
# note that srcs are in libraries or other directories;
# $(CXXSRC:.cpp=.o) will cause obj files to be in same loc as src files
#~ OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o)
# to change the output directory for object files;
# must change the obj list here!
# and then, match to corresponding rule somehow?
# or leave this - and parse in rule (auth automatic variable $(@F))?
# "Suffix Replacement"
OBJ = $(SRC:.c=.o) $(CXXSRC:.cpp=.o) $(ASRC:.S=.o)
# added - OBJ list, transformed into applet/
OBJT = $(addprefix applet/,$(notdir $(OBJ)))
ALLSRC = $(SRC) $(CXXSRC) $(ASRC)
# Define all listing files.
LST = $(ASRC:.S=.lst) $(CXXSRC:.cpp=.lst) $(SRC:.c=.lst)
# Combine all necessary flags and optional flags.
# Add target processor to flags.
ALL_CFLAGS = -mmcu=$(BUILD_MCU) -I. $(CFLAGS)
ALL_CXXFLAGS = -mmcu=$(BUILD_MCU) -I. $(CXXFLAGS)
ALL_ASFLAGS = -mmcu=$(BUILD_MCU) -I. -x assembler-with-cpp $(ASFLAGS)
# depended libraries of .pde need to be added from
# $(INSTALL_DIR)/libraries (TODO: and/or ~/sketchbook/libraries)
# grep for 'include', test if exists, add...
# note: prefix "a real tab character" http://www.delorie.com/djgpp/doc/ug/larger/makefiles.html
# $$ to escape $ for shell;
# note: must NOT put comments # inside bash execution;
# those would get removed by make; making shell see "EOF in backquote substitution"
# echo $$ix ; \
# 'shell' twice - for each subprocess! Backtick doesn't get expanded?
GREPRES:=$(shell for ix in $(shell grep include $(TARGET).pde | sed 's/.*[<"]\(.*\).h[>"].*/\1/'); do \
if [ -d $(INSTALL_DIR)/libraries/$$ix ] ; then \
LINCS="$$LINCS -I$(INSTALL_DIR)/libraries/$$ix" ;\
fi; \
done; \
echo $$LINCS)
# append includes:
CINCS += $(GREPRES)
CXXINCS += $(GREPRES)
# append library source .cpp files too (CXXSRC)
GREPRESB:=$(shell for ix in $(shell grep include $(TARGET).pde | sed 's/.*[<"]\(.*\).h[>"].*/\1/'); do \
if [ -d $(INSTALL_DIR)/libraries/$$ix ] ; then \
CPPSRCS="$$CPPSRCS $(INSTALL_DIR)/libraries/$$ix/*.cpp" ;\
fi; \
done; \
echo $$CPPSRCS)
CXXSRC += $(GREPRESB)
# added - only CXX obj from libraries:
CXXLIBOBJ = $(GREPRESB:.cpp=.o)
# Default target.
all: applet_files build sizeafter
build: elf hex
applet_files: $(TARGET).pde
# Here is the "preprocessing".
# It creates a .cpp file based with the same name as the .pde file.
# On top of the new .cpp file comes the WProgram.h header.
# At the end there is a generic main() function attached.
# Then the .cpp file will be compiled. Errors during compile will
# refer to this new, automatically generated, file.
# Not the original .pde file you actually edit...
test -d applet || mkdir applet
# @ supresses printout of the cmdline itself; so only the out of echo is printed
@echo ALL OBJT: $(OBJT)
@echo ALL CXXLIBOBJ: $(CXXLIBOBJ)
# echo '#include "WProgram.h"' > applet/$(TARGET).cpp
@echo "#include \"WProgram.h\"\nvoid setup();\nvoid loop();\n" > applet/$(TARGET).cpp
cat $(TARGET).pde >> applet/$(TARGET).cpp
# no more need to cat main.cpp (v0022) - now it is compiled in
# cat $(ARDUINO)/main.cpp >> applet/$(TARGET).cpp
elf: applet/$(TARGET).elf
hex: applet/$(TARGET).hex
eep: applet/$(TARGET).eep
lss: applet/$(TARGET).lss
sym: applet/$(TARGET).sym
# Program the device.
upload: applet/$(TARGET).hex
$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH)
# Display size of file.
HEXSIZE = $(SIZE) --target=$(FORMAT) applet/$(TARGET).hex
ELFSIZE = $(SIZE) applet/$(TARGET).elf
sizebefore:
@if [ -f applet/$(TARGET).elf ]; then echo; echo $(MSG_SIZE_BEFORE); $(HEXSIZE); echo; fi
sizeafter:
@if [ -f applet/$(TARGET).elf ]; then echo; echo $(MSG_SIZE_AFTER); $(HEXSIZE); echo; fi
# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
COFFCONVERT=$(OBJCOPY) --debugging \
--change-section-address .data-0x800000 \
--change-section-address .bss-0x800000 \
--change-section-address .noinit-0x800000 \
--change-section-address .eeprom-0x810000
coff: applet/$(TARGET).elf
$(COFFCONVERT) -O coff-avr applet/$(TARGET).elf $(TARGET).cof
extcoff: $(TARGET).elf
$(COFFCONVERT) -O coff-ext-avr applet/$(TARGET).elf $(TARGET).cof
.SUFFIXES: .elf .hex .eep .lss .sym
.elf.hex:
@$(OBJCOPY) -O ihex -R .eeprom $< $@
$(TMPDIRPATH)%.cpp: %.pde
@cat $(ARDUINO_PATH)hardware/arduino/cores/arduino/main.cpp > $@
@cat $< >> $@
@echo >> $@
@echo 'extern "C" void __cxa_pure_virtual() { while (1); }' >> $@
.PHONY: all
all: tmpdir $(HEXNAME) assemblersource showsize
ls -al $(HEXNAME) $(ELFNAME)
$(ELFNAME): $(LIBNAME)($(addprefix $(TMPDIRPATH),$(OBJFILES)))
$(LINK.o) $(COMMON_FLAGS) $(LIBNAME) $(LOADLIBES) $(LDLIBS) -o $@
$(LIBNAME)(): $(addprefix $(TMPDIRPATH),$(OBJFILES))
#=== create temp directory ===
# not really required, because it will be also created during the dependency handling
.PHONY: tmpdir
tmpdir:
@test -d $(TMPDIRPATH) || mkdir $(TMPDIRPATH)
#=== create assembler files for each C/C++ file ===
.PHONY: assemblersource
assemblersource: $(addprefix $(TMPDIRPATH),$(ASSFILES)) $(addprefix $(TMPDIRPATH),$(DISFILES))
#=== show the section sizes of the ELF file ===
.PHONY: showsize
showsize: $(ELFNAME)
$(SIZE) $<
#=== clean up target ===
# this is simple: the TMPDIRPATH is removed
.PHONY: clean
$(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@
.elf.eep:
-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
--change-section-lma .eeprom=0 -O $(FORMAT) $< $@
# Create extended listing file from ELF output file.
.elf.lss:
$(OBJDUMP) -h -S $< > $@
# Create a symbol table from ELF output file.
.elf.sym:
$(NM) -n $< > $@
# Link: create ELF output file from library.
# NOTE: applet/$(TARGET).cpp.o MUST BE BEFORE applet/core.a
# in the dependency list, so its rule runs first!
applet/$(TARGET).elf: $(TARGET).pde applet/$(TARGET).cpp.o applet/core.a
# $(CC) $(ALL_CFLAGS) -o $@ applet/$(TARGET).cpp -L. applet/core.a $(LDFLAGS)
# changed as in IDE v0022: link cpp obj files
@echo $$(tput bold)$$(tput setaf 2) $(CC) $$(tput sgr0) $(ALL_CFLAGS) $(CFINALF) -o $@ applet/$(TARGET).cpp.o $(CXXOBJ) -L. applet/core.a $(LDFLAGS)
@$(CC) $(ALL_CFLAGS) $(CFINALF) -o $@ applet/$(TARGET).cpp.o $(CXXOBJ) -L. applet/core.a $(LDFLAGS)
# added: cpp.o depends on cpp (and .pde which generates it)
# $< "first item in the dependencies list"; $@ "left side of the :"; $^ "right side of the :"
# http://www.cs.colby.edu/maxwell/courses/tutorials/maketutor/
applet/$(TARGET).cpp.o: applet/$(TARGET).cpp
@echo $$(tput bold) $(CXX) $$(tput sgr0) -c $(ALL_CXXFLAGS) $< -o $@
@$(CXX) -c $(ALL_CXXFLAGS) $< -o $@
#~ applet/core.a: $(OBJ)
#~ @for i in $(OBJ); do echo $(AR) rcs applet/core.a $$i; $(AR) rcs applet/core.a $$i; done
applet/core.a: $(OBJT)
@for i in $(OBJT); do echo $(AR) rcs applet/core.a $$i; $(AR) rcs applet/core.a $$i; done
# iterate through OBJ to find the original location; then build depending on source extension
# TODO: add handling of assembler files
applet/%.o:
@for iob in $(OBJ); do \
if [ "`basename $$iob`" = "`basename $@`" ]; then \
for ios in $(ALLSRC); do \
if [ "$${iob%%.*}" = "$${ios%%.*}" ]; then \
case $${ios##*.} in \
"cpp") \
echo "$$(tput bold)$$(tput setaf 1) $(CXX) $$(tput sgr0) -c $(ALL_CXXFLAGS) $$ios -o $@"; \
$(CXX) -c $(ALL_CXXFLAGS) $$ios -o $@;; \
"c") \
echo "$$(tput bold)$$(tput setaf 1) $(CC) $$(tput sgr0) -c $(ALL_CFLAGS) $$ios -o $@"; \
$(CC) -c $(ALL_CFLAGS) $$ios -o $@;; \
esac; \
fi; \
done; \
fi; \
done;
#~ # Compile: create object files from C++ source files.
#~ .cpp.o:
#~ $(CXX) -c $(ALL_CXXFLAGS) $< -o $@
#~ # Compile: create object files from C source files.
#~ .c.o:
#~ $(CC) -c $(ALL_CFLAGS) $< -o $@
#~ # Compile: create assembler files from C source files.
#~ .c.s:
#~ $(CC) -S $(ALL_CFLAGS) $< -o $@
#~ # Assemble: create object files from assembler source files.
#~ .S.o:
#~ $(CC) -c $(ALL_ASFLAGS) $< -o $@
#~ # Automatic dependencies
#~ %.d: %.c
#~ $(CC) -M $(ALL_CFLAGS) $< | sed "s;$(notdir $*).o:;$*.o $*.d:;" > $@
#~ %.d: %.cpp
#~ $(CXX) -M $(ALL_CXXFLAGS) $< | sed "s;$(notdir $*).o:;$*.o $*.d:;" > $@
# Target: clean project.
clean:
$(RM) $(TMPDIRPATH)
# Program the device.
# step 1: reset the arduino board with the stty command
# step 2: user avrdude to upload the software
.PHONY: upload
upload: $(HEXNAME)
stty -F $(AVRDUDE_PORT) hupcl
$(AVRDUDE) $(AVRDUDE_FLAGS)
# === dependency handling ===
# From the gnu make manual (section 4.14, Generating Prerequisites Automatically)
# Additionally (because this will be the first executed rule) TMPDIRPATH is created here.
# Instead of "sed" the "echo" command is used
# cd $(TMPDIRPATH); mkdir -p $(DIRS) 2> /dev/null; cd ..
DEPACTION=test -d $(TMPDIRPATH) || mkdir $(TMPDIRPATH);\
mkdir -p $(addprefix $(TMPDIRPATH),$(DIRS));\
set -e; echo -n $@ $(dir $@) > $@; $(CC) -MM $(COMMON_FLAGS) $< >> $@
$(TMPDIRPATH)%.d: %.c
@$(DEPACTION)
$(TMPDIRPATH)%.d: %.cc
@$(DEPACTION)
$(TMPDIRPATH)%.d: %.cpp
@$(DEPACTION)
# Include dependency files. If a .d file is missing, a warning is created and the .d file is created
# This warning is not a problem (gnu make manual, section 3.3 Including Other Makefiles)
-include $(addprefix $(TMPDIRPATH),$(DEPFILES))
$(REMOVE) applet/$(TARGET).hex applet/$(TARGET).eep applet/$(TARGET).cof applet/$(TARGET).elf \
applet/$(TARGET).map applet/$(TARGET).sym applet/$(TARGET).lss applet/core.a \
$(OBJT) applet/$(TARGET).cpp.o \
$(OBJ) $(LST) $(SRC:.c=.s) $(SRC:.c=.d) $(CXXSRC:.cpp=.s) $(CXXSRC:.cpp=.d)
.PHONY: all build elf hex eep lss sym program coff extcoff clean applet_files sizebefore sizeafter

165
Marlin/Marlin.h
Unescape View File

@ -1,83 +1,82 @@
#ifndef __MARLINH
#define __MARLINH
// Tonokip RepRap firmware rewrite based off of Hydra-mmm firmware.
// Licence: GPL
#include <WProgram.h>
#include "fastio.h"
#define ECHO(x) Serial << "echo: " << x;
#define ECHOLN(x) Serial << "echo: "<<x<<endl;
void get_command();
void process_commands();
void manage_inactivity(byte debug);
#if X_ENABLE_PIN > -1
#define enable_x() WRITE(X_ENABLE_PIN, X_ENABLE_ON)
#define disable_x() WRITE(X_ENABLE_PIN,!X_ENABLE_ON)
#else
#define enable_x() ;
#define disable_x() ;
#endif
#if Y_ENABLE_PIN > -1
#define enable_y() WRITE(Y_ENABLE_PIN, Y_ENABLE_ON)
#define disable_y() WRITE(Y_ENABLE_PIN,!Y_ENABLE_ON)
#else
#define enable_y() ;
#define disable_y() ;
#endif
#if Z_ENABLE_PIN > -1
#define enable_z() WRITE(Z_ENABLE_PIN, Z_ENABLE_ON)
#define disable_z() WRITE(Z_ENABLE_PIN,!Z_ENABLE_ON)
#else
#define enable_z() ;
#define disable_z() ;
#endif
#if E_ENABLE_PIN > -1
#define enable_e() WRITE(E_ENABLE_PIN, E_ENABLE_ON)
#define disable_e() WRITE(E_ENABLE_PIN,!E_ENABLE_ON)
#else
#define enable_e() ;
#define disable_e() ;
#endif
#define X_AXIS 0
#define Y_AXIS 1
#define Z_AXIS 2
#define E_AXIS 3
void FlushSerialRequestResend();
void ClearToSend();
void get_coordinates();
void prepare_move();
void kill(byte debug);
//void check_axes_activity();
//void plan_init();
//void st_init();
//void tp_init();
//void plan_buffer_line(float x, float y, float z, float e, float feed_rate);
//void plan_set_position(float x, float y, float z, float e);
//void st_wake_up();
//void st_synchronize();
void enquecommand(const char *cmd);
void wd_reset();
#ifndef CRITICAL_SECTION_START
#define CRITICAL_SECTION_START unsigned char _sreg = SREG; cli();
#define CRITICAL_SECTION_END SREG = _sreg;
#endif //CRITICAL_SECTION_START
extern float homing_feedrate[];
extern bool axis_relative_modes[];
void manage_inactivity(byte debug);
#endif
#ifndef __MARLINH
#define __MARLINH
// Tonokip RepRap firmware rewrite based off of Hydra-mmm firmware.
// Licence: GPL
#include <WProgram.h>
#include "fastio.h"
#define ECHO(x) Serial << "echo: " << x;
#define ECHOLN(x) Serial << "echo: "<<x<<endl;
void get_command();
void process_commands();
void manage_inactivity(byte debug);
#if X_ENABLE_PIN > -1
#define enable_x() WRITE(X_ENABLE_PIN, X_ENABLE_ON)
#define disable_x() WRITE(X_ENABLE_PIN,!X_ENABLE_ON)
#else
#define enable_x() ;
#define disable_x() ;
#endif
#if Y_ENABLE_PIN > -1
#define enable_y() WRITE(Y_ENABLE_PIN, Y_ENABLE_ON)
#define disable_y() WRITE(Y_ENABLE_PIN,!Y_ENABLE_ON)
#else
#define enable_y() ;
#define disable_y() ;
#endif
#if Z_ENABLE_PIN > -1
#define enable_z() WRITE(Z_ENABLE_PIN, Z_ENABLE_ON)
#define disable_z() WRITE(Z_ENABLE_PIN,!Z_ENABLE_ON)
#else
#define enable_z() ;
#define disable_z() ;
#endif
#if E_ENABLE_PIN > -1
#define enable_e() WRITE(E_ENABLE_PIN, E_ENABLE_ON)
#define disable_e() WRITE(E_ENABLE_PIN,!E_ENABLE_ON)
#else
#define enable_e() ;
#define disable_e() ;
#endif
#define X_AXIS 0
#define Y_AXIS 1
#define Z_AXIS 2
#define E_AXIS 3
void FlushSerialRequestResend();
void ClearToSend();
void get_coordinates();
void prepare_move();
void kill();
//void check_axes_activity();
//void plan_init();
//void st_init();
//void tp_init();
//void plan_buffer_line(float x, float y, float z, float e, float feed_rate);
//void plan_set_position(float x, float y, float z, float e);
//void st_wake_up();
//void st_synchronize();
void enquecommand(const char *cmd);
#ifndef CRITICAL_SECTION_START
#define CRITICAL_SECTION_START unsigned char _sreg = SREG; cli();
#define CRITICAL_SECTION_END SREG = _sreg;
#endif //CRITICAL_SECTION_START
extern float homing_feedrate[];
extern bool axis_relative_modes[];
void wd_reset() ;
#endif

2466
Marlin/Marlin.pde
View File

File diff suppressed because it is too large Load Diff

10
Marlin/fastio.h
Unescape View File

@ -24,12 +24,12 @@
*/
/// Read a pin
#define _READ(IO) ((bool)(DIO ## IO ## _RPORT & MASK(DIO ## IO ## _PIN)))
#define _READ(IO) ((bool)(DIO ## IO ## _RPORT & MASK(DIO ## IO ## _PIN)))
/// write to a pin
#define _WRITE(IO, v) do { if (v) {DIO ## IO ## _WPORT |= MASK(DIO ## IO ## _PIN); } else {DIO ## IO ## _WPORT &= ~MASK(DIO ## IO ## _PIN); }; } while (0)
//#define _WRITE(IO, v) do { #if (DIO ## IO ## _WPORT >= 0x100) CRITICAL_SECTION_START; if (v) {DIO ## IO ## _WPORT |= MASK(DIO ## IO ## _PIN); } else {DIO ## IO ## _WPORT &= ~MASK(DIO ## IO ## _PIN); };#if (DIO ## IO ## _WPORT >= 0x100) CRITICAL_SECTION_END; } while (0)
#define _WRITE(IO, v) do { if (v) {DIO ## IO ## _WPORT |= MASK(DIO ## IO ## _PIN); } else {DIO ## IO ## _WPORT &= ~MASK(DIO ## IO ## _PIN); }; } while (0)
//#define _WRITE(IO, v) do { #if (DIO ## IO ## _WPORT >= 0x100) CRITICAL_SECTION_START; if (v) {DIO ## IO ## _WPORT |= MASK(DIO ## IO ## _PIN); } else {DIO ## IO ## _WPORT &= ~MASK(DIO ## IO ## _PIN); };#if (DIO ## IO ## _WPORT >= 0x100) CRITICAL_SECTION_END; } while (0)
/// toggle a pin
#define _TOGGLE(IO) do {DIO ## IO ## _RPORT = MASK(DIO ## IO ## _PIN); } while (0)
#define _TOGGLE(IO) do {DIO ## IO ## _RPORT = MASK(DIO ## IO ## _PIN); } while (0)
/// set pin as input
#define _SET_INPUT(IO) do {DIO ## IO ## _DDR &= ~MASK(DIO ## IO ## _PIN); } while (0)
@ -2556,4 +2556,4 @@ pins
#error pins for this chip not defined in arduino.h! If you write an appropriate pin definition and have this firmware work on your chip, please submit a pull request
#endif
#endif /* _ARDUINO_H */
#endif /* _ARDUINO_H */

10
Marlin/lcd.h
Unescape View File

@ -1,10 +0,0 @@
#ifndef __LCDH
#define __LCDH
#endif

1
Marlin/lcd.pde
Unescape View File

@ -1 +0,0 @@

18
Marlin/planner.cpp
Unescape View File

@ -381,13 +381,6 @@ void check_axes_activity() {
// calculation the caller must also provide the physical length of the line in millimeters.
void plan_buffer_line(float x, float y, float z, float e, float feed_rate) {
// The target position of the tool in absolute steps
// Calculate target position in absolute steps
long target[4];
target[X_AXIS] = lround(x*axis_steps_per_unit[X_AXIS]);
target[Y_AXIS] = lround(y*axis_steps_per_unit[Y_AXIS]);
target[Z_AXIS] = lround(z*axis_steps_per_unit[Z_AXIS]);
target[E_AXIS] = lround(e*axis_steps_per_unit[E_AXIS]);
// Calculate the buffer head after we push this byte
int next_buffer_head = (block_buffer_head + 1) & (BLOCK_BUFFER_SIZE - 1);
@ -400,6 +393,15 @@ void plan_buffer_line(float x, float y, float z, float e, float feed_rate) {
LCD_STATUS;
}
// The target position of the tool in absolute steps
// Calculate target position in absolute steps
//this should be done after the wait, because otherwise a M92 code within the gcode disrupts this calculation somehow
long target[4];
target[X_AXIS] = lround(x*axis_steps_per_unit[X_AXIS]);
target[Y_AXIS] = lround(y*axis_steps_per_unit[Y_AXIS]);
target[Z_AXIS] = lround(z*axis_steps_per_unit[Z_AXIS]);
target[E_AXIS] = lround(e*axis_steps_per_unit[E_AXIS]);
// Prepare to set up new block
block_t *block = &block_buffer[block_buffer_head];
@ -433,7 +435,7 @@ void plan_buffer_line(float x, float y, float z, float e, float feed_rate) {
unsigned long microseconds;
if (block->steps_e == 0) {
if(feed_rate<mintravelfeedrate) feed_rate=mintravelfeedrate;
if(feed_rate<mintravelfeedrate) feed_rate=mintravelfeedrate;
}
else {
if(feed_rate<minimumfeedrate) feed_rate=minimumfeedrate;

182
Marlin/planner.h
Unescape View File

@ -1,90 +1,92 @@
/*
planner.h - buffers movement commands and manages the acceleration profile plan
Part of Grbl
Copyright (c) 2009-2011 Simen Svale Skogsrud
Grbl is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
Grbl is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
*/
// This module is to be considered a sub-module of stepper.c. Please don't include
// this file from any other module.
#ifndef planner_h
#define planner_h
// This struct is used when buffering the setup for each linear movement "nominal" values are as specified in
// the source g-code and may never actually be reached if acceleration management is active.
typedef struct {
// Fields used by the bresenham algorithm for tracing the line
long steps_x, steps_y, steps_z, steps_e; // Step count along each axis
long step_event_count; // The number of step events required to complete this block
volatile long accelerate_until; // The index of the step event on which to stop acceleration
volatile long decelerate_after; // The index of the step event on which to start decelerating
volatile long acceleration_rate; // The acceleration rate used for acceleration calculation
unsigned char direction_bits; // The direction bit set for this block (refers to *_DIRECTION_BIT in config.h)
#ifdef ADVANCE
long advance_rate;
volatile long initial_advance;
volatile long final_advance;
float advance;
#endif
// Fields used by the motion planner to manage acceleration
float speed_x, speed_y, speed_z, speed_e; // Nominal mm/minute for each axis
float nominal_speed; // The nominal speed for this block in mm/min
float millimeters; // The total travel of this block in mm
float entry_speed;
float acceleration; // acceleration mm/sec^2
// Settings for the trapezoid generator
long nominal_rate; // The nominal step rate for this block in step_events/sec
volatile long initial_rate; // The jerk-adjusted step rate at start of block
volatile long final_rate; // The minimal rate at exit
long acceleration_st; // acceleration steps/sec^2
volatile char busy;
} block_t;
// Initialize the motion plan subsystem
void plan_init();
// Add a new linear movement to the buffer. x, y and z is the signed, absolute target position in
// millimaters. Feed rate specifies the speed of the motion.
void plan_buffer_line(float x, float y, float z, float e, float feed_rate);
// Set position. Used for G92 instructions.
void plan_set_position(float x, float y, float z, float e);
// Called when the current block is no longer needed. Discards the block and makes the memory
// availible for new blocks.
void plan_discard_current_block();
// Gets the current block. Returns NULL if buffer empty
block_t *plan_get_current_block();
void check_axes_activity();
extern unsigned long minsegmenttime;
extern float max_feedrate[4]; // set the max speeds
extern float axis_steps_per_unit[4];
extern long max_acceleration_units_per_sq_second[4]; // Use M201 to override by software
extern float minimumfeedrate;
extern float acceleration; // Normal acceleration mm/s^2 THIS IS THE DEFAULT ACCELERATION for all moves. M204 SXXXX
extern float retract_acceleration; // mm/s^2 filament pull-pack and push-forward while standing still in the other axis M204 TXXXX
extern float max_xy_jerk; //speed than can be stopped at once, if i understand correctly.
extern float max_z_jerk;
extern float mintravelfeedrate;
extern unsigned long axis_steps_per_sqr_second[NUM_AXIS];
#endif
/*
planner.h - buffers movement commands and manages the acceleration profile plan
Part of Grbl
Copyright (c) 2009-2011 Simen Svale Skogsrud
Grbl is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
Grbl is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
*/
// This module is to be considered a sub-module of stepper.c. Please don't include
// this file from any other module.
#ifndef planner_h
#define planner_h
#include "Configuration.h"
// This struct is used when buffering the setup for each linear movement "nominal" values are as specified in
// the source g-code and may never actually be reached if acceleration management is active.
typedef struct {
// Fields used by the bresenham algorithm for tracing the line
long steps_x, steps_y, steps_z, steps_e; // Step count along each axis
long step_event_count; // The number of step events required to complete this block
volatile long accelerate_until; // The index of the step event on which to stop acceleration
volatile long decelerate_after; // The index of the step event on which to start decelerating
volatile long acceleration_rate; // The acceleration rate used for acceleration calculation
unsigned char direction_bits; // The direction bit set for this block (refers to *_DIRECTION_BIT in config.h)
#ifdef ADVANCE
long advance_rate;
volatile long initial_advance;
volatile long final_advance;
float advance;
#endif
// Fields used by the motion planner to manage acceleration
float speed_x, speed_y, speed_z, speed_e; // Nominal mm/minute for each axis
float nominal_speed; // The nominal speed for this block in mm/min
float millimeters; // The total travel of this block in mm
float entry_speed;
float acceleration; // acceleration mm/sec^2
// Settings for the trapezoid generator
long nominal_rate; // The nominal step rate for this block in step_events/sec
volatile long initial_rate; // The jerk-adjusted step rate at start of block
volatile long final_rate; // The minimal rate at exit
long acceleration_st; // acceleration steps/sec^2
volatile char busy;
} block_t;
// Initialize the motion plan subsystem
void plan_init();
// Add a new linear movement to the buffer. x, y and z is the signed, absolute target position in
// millimaters. Feed rate specifies the speed of the motion.
void plan_buffer_line(float x, float y, float z, float e, float feed_rate);
// Set position. Used for G92 instructions.
void plan_set_position(float x, float y, float z, float e);
// Called when the current block is no longer needed. Discards the block and makes the memory
// availible for new blocks.
void plan_discard_current_block();
// Gets the current block. Returns NULL if buffer empty
block_t *plan_get_current_block();
void check_axes_activity();
extern unsigned long minsegmenttime;
extern float max_feedrate[4]; // set the max speeds
extern float axis_steps_per_unit[4];
extern long max_acceleration_units_per_sq_second[4]; // Use M201 to override by software
extern float minimumfeedrate;
extern float acceleration; // Normal acceleration mm/s^2 THIS IS THE DEFAULT ACCELERATION for all moves. M204 SXXXX
extern float retract_acceleration; // mm/s^2 filament pull-pack and push-forward while standing still in the other axis M204 TXXXX
extern float max_xy_jerk; //speed than can be stopped at once, if i understand correctly.
extern float max_z_jerk;
extern float mintravelfeedrate;
extern unsigned long axis_steps_per_sqr_second[NUM_AXIS];
#endif

2
Marlin/stepper.cpp
Unescape View File

@ -115,7 +115,7 @@ asm volatile ( \
#define ENABLE_STEPPER_DRIVER_INTERRUPT() TIMSK1 |= (1<<OCIE1A)
#define DISABLE_STEPPER_DRIVER_INTERRUPT() TIMSK1 &= ~(1<<OCIE1A)
static block_t *current_block; // A pointer to the block currently being traced
block_t *current_block; // A pointer to the block currently being traced
// Variables used by The Stepper Driver Interrupt
static unsigned char out_bits; // The next stepping-bits to be output

84
Marlin/stepper.h
Unescape View File

@ -1,40 +1,44 @@
/*
stepper.h - stepper motor driver: executes motion plans of planner.c using the stepper motors
Part of Grbl
Copyright (c) 2009-2011 Simen Svale Skogsrud
Grbl is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
Grbl is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
*/
#ifndef stepper_h
#define stepper_h
// Initialize and start the stepper motor subsystem
void st_init();
// Block until all buffered steps are executed
void st_synchronize();
// The stepper subsystem goes to sleep when it runs out of things to execute. Call this
// to notify the subsystem that it is time to go to work.
void st_wake_up();
// if DEBUG_STEPS is enabled, M114 can be used to compare two methods of determining the X,Y,Z position of the printer.
// for debugging purposes only, should be disabled by default
#ifdef DEBUG_STEPS
extern volatile long count_position[NUM_AXIS];
extern volatile int count_direction[NUM_AXIS];
#endif
#endif
/*
stepper.h - stepper motor driver: executes motion plans of planner.c using the stepper motors
Part of Grbl
Copyright (c) 2009-2011 Simen Svale Skogsrud
Grbl is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
Grbl is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
*/
#ifndef stepper_h
#define stepper_h
#include "planner.h"
// Initialize and start the stepper motor subsystem
void st_init();
// Block until all buffered steps are executed
void st_synchronize();
// The stepper subsystem goes to sleep when it runs out of things to execute. Call this
// to notify the subsystem that it is time to go to work.
void st_wake_up();
// if DEBUG_STEPS is enabled, M114 can be used to compare two methods of determining the X,Y,Z position of the printer.
// for debugging purposes only, should be disabled by default
#ifdef DEBUG_STEPS
extern volatile long count_position[NUM_AXIS];
extern volatile int count_direction[NUM_AXIS];
#endif
extern block_t *current_block; // A pointer to the block currently being traced
#endif

29
Marlin/temperature.cpp
Unescape View File

@ -90,14 +90,15 @@ void manage_heater()
float pid_input;
float pid_output;
if(temp_meas_ready == true) {
if(temp_meas_ready != true) //better readability
return;
CRITICAL_SECTION_START;
temp_meas_ready = false;
CRITICAL_SECTION_END;
#ifdef PIDTEMP
pid_input = analog2temp(current_raw[0]);
pid_input = analog2temp(current_raw[TEMPSENSOR_HOTEND]);
#ifndef PID_OPENLOOP
pid_error = pid_setpoint - pid_input;
@ -118,10 +119,13 @@ CRITICAL_SECTION_END;
temp_iState += pid_error;
temp_iState = constrain(temp_iState, temp_iState_min, temp_iState_max);
iTerm = Ki * temp_iState;
#define K1 0.95
//K1 defined in Configuration.h in the PID settings
#define K2 (1.0-K1)
dTerm = (Kd * (pid_input - temp_dState))*K2 + (K1 * dTerm);
temp_dState = pid_input;
#ifdef PID_ADD_EXTRUSION_RATE
pTerm+=Kc*current_block->speed_e; //additional heating if extrusion speed is high
#endif
pid_output = constrain(pTerm + iTerm - dTerm, 0, PID_MAX);
}
#endif //PID_OPENLOOP
@ -157,7 +161,7 @@ CRITICAL_SECTION_END;
previous_millis_bed_heater = millis();
#if TEMP_1_PIN > -1
if(current_raw[1] >= target_raw[1])
if(current_raw[TEMPSENSOR_BED] >= target_raw[TEMPSENSOR_BED])
{
WRITE(HEATER_1_PIN,LOW);
}
@ -167,7 +171,6 @@ CRITICAL_SECTION_END;
}
#endif
}
}
// Takes hot end temperature value as input and returns corresponding raw value.
// For a thermistor, it uses the RepRap thermistor temp table.
@ -428,15 +431,15 @@ ISR(TIMER0_COMPB_vect)
raw_temp_2_value = 0;
#ifdef MAXTEMP
#if (HEATER_0_PIN > -1)
if(current_raw[0] >= maxttemp) {
target_raw[0] = 0;
if(current_raw[TEMPSENSOR_HOTEND] >= maxttemp) {
target_raw[TEMPSENSOR_HOTEND] = 0;
analogWrite(HEATER_0_PIN, 0);
Serial.println("!! Temperature extruder 0 switched off. MAXTEMP triggered !!");
}
#endif
#if (HEATER_2_PIN > -1)
if(current_raw[2] >= maxttemp) {
target_raw[2] = 0;
if(current_raw[TEMPSENSOR_AUX] >= maxttemp) {
target_raw[TEMPSENSOR_AUX] = 0;
analogWrite(HEATER_2_PIN, 0);
Serial.println("!! Temperature extruder 1 switched off. MAXTEMP triggered !!");
}
@ -444,15 +447,15 @@ ISR(TIMER0_COMPB_vect)
#endif //MAXTEMP
#ifdef MINTEMP
#if (HEATER_0_PIN > -1)
if(current_raw[0] <= minttemp) {
target_raw[0] = 0;
if(current_raw[TEMPSENSOR_HOTEND] <= minttemp) {
target_raw[TEMPSENSOR_HOTEND] = 0;
analogWrite(HEATER_0_PIN, 0);
Serial.println("!! Temperature extruder 0 switched off. MINTEMP triggered !!");
}
#endif
#if (HEATER_2_PIN > -1)
if(current_raw[2] <= minttemp) {
target_raw[2] = 0;
if(current_raw[TEMPSENSOR_AUX] <= minttemp) {
target_raw[TEMPSENSOR_AUX] = 0;
analogWrite(HEATER_2_PIN, 0);
Serial.println("!! Temperature extruder 1 switched off. MINTEMP triggered !!");
}

113
Marlin/temperature.h
Unescape View File

@ -1,55 +1,58 @@
/*
temperature.h - temperature controller
Part of Marlin
Copyright (c) 2011 Erik van der Zalm
Grbl is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
Grbl is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
*/
#ifndef temperature_h
#define temperature_h
void manage_inactivity(byte debug);
void tp_init();
void manage_heater();
//int temp2analogu(int celsius, const short table[][2], int numtemps);
//float analog2tempu(int raw, const short table[][2], int numtemps);
float temp2analog(int celsius);
float temp2analogBed(int celsius);
float analog2temp(int raw);
float analog2tempBed(int raw);
#ifdef HEATER_USES_THERMISTOR
#define HEATERSOURCE 1
#endif
#ifdef BED_USES_THERMISTOR
#define BEDSOURCE 1
#endif
//#define temp2analogh( c ) temp2analogu((c),temptable,NUMTEMPS)
//#define analog2temp( c ) analog2tempu((c),temptable,NUMTEMPS
extern float Kp;
extern float Ki;
extern float Kd;
extern float Kc;
extern int target_raw[3];
extern int current_raw[3];
extern double pid_setpoint;
#endif
/*
temperature.h - temperature controller
Part of Marlin
Copyright (c) 2011 Erik van der Zalm
Grbl is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
Grbl is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
*/
#ifndef temperature_h
#define temperature_h
#include "Marlin.h"
#ifdef PID_ADD_EXTRUSION_RATE
#include "stepper.h"
#endif
void tp_init();
void manage_heater();
//int temp2analogu(int celsius, const short table[][2], int numtemps);
//float analog2tempu(int raw, const short table[][2], int numtemps);
float temp2analog(int celsius);
float temp2analogBed(int celsius);
float analog2temp(int raw);
float analog2tempBed(int raw);
#ifdef HEATER_USES_THERMISTOR
#define HEATERSOURCE 1
#endif
#ifdef BED_USES_THERMISTOR
#define BEDSOURCE 1
#endif
//#define temp2analogh( c ) temp2analogu((c),temptable,NUMTEMPS)
//#define analog2temp( c ) analog2tempu((c),temptable,NUMTEMPS
extern float Kp;
extern float Ki;
extern float Kd;
extern float Kc;
enum {TEMPSENSOR_HOTEND=0,TEMPSENSOR_BED=1, TEMPSENSOR_AUX=2};
extern int target_raw[3];
extern int current_raw[3];
extern double pid_setpoint;
#endif

180
Marlin/thermistortables.h
Unescape View File

@ -7,67 +7,67 @@
#define NUMTEMPS_1 61
const short temptable_1[NUMTEMPS_1][2] = {
{ 23*OVERSAMPLENR , 300 },
{ 25*OVERSAMPLENR , 295 },
{ 27*OVERSAMPLENR , 290 },
{ 28*OVERSAMPLENR , 285 },
{ 31*OVERSAMPLENR , 280 },
{ 33*OVERSAMPLENR , 275 },
{ 35*OVERSAMPLENR , 270 },
{ 38*OVERSAMPLENR , 265 },
{ 41*OVERSAMPLENR , 260 },
{ 44*OVERSAMPLENR , 255 },
{ 48*OVERSAMPLENR , 250 },
{ 52*OVERSAMPLENR , 245 },
{ 56*OVERSAMPLENR , 240 },
{ 61*OVERSAMPLENR , 235 },
{ 66*OVERSAMPLENR , 230 },
{ 71*OVERSAMPLENR , 225 },
{ 78*OVERSAMPLENR , 220 },
{ 84*OVERSAMPLENR , 215 },
{ 92*OVERSAMPLENR , 210 },
{ 100*OVERSAMPLENR , 205 },
{ 109*OVERSAMPLENR , 200 },
{ 120*OVERSAMPLENR , 195 },
{ 131*OVERSAMPLENR , 190 },
{ 143*OVERSAMPLENR , 185 },
{ 156*OVERSAMPLENR , 180 },
{ 171*OVERSAMPLENR , 175 },
{ 187*OVERSAMPLENR , 170 },
{ 205*OVERSAMPLENR , 165 },
{ 224*OVERSAMPLENR , 160 },
{ 245*OVERSAMPLENR , 155 },
{ 268*OVERSAMPLENR , 150 },
{ 293*OVERSAMPLENR , 145 },
{ 320*OVERSAMPLENR , 140 },
{ 348*OVERSAMPLENR , 135 },
{ 379*OVERSAMPLENR , 130 },
{ 411*OVERSAMPLENR , 125 },
{ 445*OVERSAMPLENR , 120 },
{ 480*OVERSAMPLENR , 115 },
{ 516*OVERSAMPLENR , 110 },
{ 553*OVERSAMPLENR , 105 },
{ 591*OVERSAMPLENR , 100 },
{ 628*OVERSAMPLENR , 95 },
{ 665*OVERSAMPLENR , 90 },
{ 702*OVERSAMPLENR , 85 },
{ 737*OVERSAMPLENR , 80 },
{ 770*OVERSAMPLENR , 75 },
{ 801*OVERSAMPLENR , 70 },
{ 830*OVERSAMPLENR , 65 },
{ 857*OVERSAMPLENR , 60 },
{ 881*OVERSAMPLENR , 55 },
{ 903*OVERSAMPLENR , 50 },
{ 922*OVERSAMPLENR , 45 },
{ 939*OVERSAMPLENR , 40 },
{ 954*OVERSAMPLENR , 35 },
{ 966*OVERSAMPLENR , 30 },
{ 977*OVERSAMPLENR , 25 },
{ 985*OVERSAMPLENR , 20 },
{ 993*OVERSAMPLENR , 15 },
{ 999*OVERSAMPLENR , 10 },
{ 1004*OVERSAMPLENR , 5 },
{ 1008*OVERSAMPLENR , 0 } //safety
{ 23*OVERSAMPLENR , 300 },
{ 25*OVERSAMPLENR , 295 },
{ 27*OVERSAMPLENR , 290 },
{ 28*OVERSAMPLENR , 285 },
{ 31*OVERSAMPLENR , 280 },
{ 33*OVERSAMPLENR , 275 },
{ 35*OVERSAMPLENR , 270 },
{ 38*OVERSAMPLENR , 265 },
{ 41*OVERSAMPLENR , 260 },
{ 44*OVERSAMPLENR , 255 },
{ 48*OVERSAMPLENR , 250 },
{ 52*OVERSAMPLENR , 245 },
{ 56*OVERSAMPLENR , 240 },
{ 61*OVERSAMPLENR , 235 },
{ 66*OVERSAMPLENR , 230 },
{ 71*OVERSAMPLENR , 225 },
{ 78*OVERSAMPLENR , 220 },
{ 84*OVERSAMPLENR , 215 },
{ 92*OVERSAMPLENR , 210 },
{ 100*OVERSAMPLENR , 205 },
{ 109*OVERSAMPLENR , 200 },
{ 120*OVERSAMPLENR , 195 },
{ 131*OVERSAMPLENR , 190 },
{ 143*OVERSAMPLENR , 185 },
{ 156*OVERSAMPLENR , 180 },
{ 171*OVERSAMPLENR , 175 },
{ 187*OVERSAMPLENR , 170 },
{ 205*OVERSAMPLENR , 165 },
{ 224*OVERSAMPLENR , 160 },
{ 245*OVERSAMPLENR , 155 },
{ 268*OVERSAMPLENR , 150 },
{ 293*OVERSAMPLENR , 145 },
{ 320*OVERSAMPLENR , 140 },
{ 348*OVERSAMPLENR , 135 },
{ 379*OVERSAMPLENR , 130 },
{ 411*OVERSAMPLENR , 125 },
{ 445*OVERSAMPLENR , 120 },
{ 480*OVERSAMPLENR , 115 },
{ 516*OVERSAMPLENR , 110 },
{ 553*OVERSAMPLENR , 105 },
{ 591*OVERSAMPLENR , 100 },
{ 628*OVERSAMPLENR , 95 },
{ 665*OVERSAMPLENR , 90 },
{ 702*OVERSAMPLENR , 85 },
{ 737*OVERSAMPLENR , 80 },
{ 770*OVERSAMPLENR , 75 },
{ 801*OVERSAMPLENR , 70 },
{ 830*OVERSAMPLENR , 65 },
{ 857*OVERSAMPLENR , 60 },
{ 881*OVERSAMPLENR , 55 },
{ 903*OVERSAMPLENR , 50 },
{ 922*OVERSAMPLENR , 45 },
{ 939*OVERSAMPLENR , 40 },
{ 954*OVERSAMPLENR , 35 },
{ 966*OVERSAMPLENR , 30 },
{ 977*OVERSAMPLENR , 25 },
{ 985*OVERSAMPLENR , 20 },
{ 993*OVERSAMPLENR , 15 },
{ 999*OVERSAMPLENR , 10 },
{ 1004*OVERSAMPLENR , 5 },
{ 1008*OVERSAMPLENR , 0 } //safety
};
#endif
#if (THERMISTORHEATER_1 == 2) || (THERMISTORHEATER_2 == 2) || (THERMISTORBED == 2) //200k bed thermistor
@ -100,35 +100,35 @@ const short temptable_2[NUMTEMPS_2][2] = {
#if (THERMISTORHEATER_1 == 3) || (THERMISTORHEATER_2 == 3) || (THERMISTORBED == 3) //mendel-parts
#define NUMTEMPS_3 28
const short temptable_3[NUMTEMPS_3][2] = {
{1*OVERSAMPLENR,864},
{21*OVERSAMPLENR,300},
{25*OVERSAMPLENR,290},
{29*OVERSAMPLENR,280},
{33*OVERSAMPLENR,270},
{39*OVERSAMPLENR,260},
{46*OVERSAMPLENR,250},
{54*OVERSAMPLENR,240},
{64*OVERSAMPLENR,230},
{75*OVERSAMPLENR,220},
{90*OVERSAMPLENR,210},
{107*OVERSAMPLENR,200},
{128*OVERSAMPLENR,190},
{154*OVERSAMPLENR,180},
{184*OVERSAMPLENR,170},
{221*OVERSAMPLENR,160},
{265*OVERSAMPLENR,150},
{316*OVERSAMPLENR,140},
{375*OVERSAMPLENR,130},
{441*OVERSAMPLENR,120},
{513*OVERSAMPLENR,110},
{588*OVERSAMPLENR,100},
{734*OVERSAMPLENR,80},
{856*OVERSAMPLENR,60},
{938*OVERSAMPLENR,40},
{986*OVERSAMPLENR,20},
{1008*OVERSAMPLENR,0},
{1018*OVERSAMPLENR,-20}
};
{1*OVERSAMPLENR,864},
{21*OVERSAMPLENR,300},
{25*OVERSAMPLENR,290},
{29*OVERSAMPLENR,280},
{33*OVERSAMPLENR,270},
{39*OVERSAMPLENR,260},
{46*OVERSAMPLENR,250},
{54*OVERSAMPLENR,240},
{64*OVERSAMPLENR,230},
{75*OVERSAMPLENR,220},
{90*OVERSAMPLENR,210},
{107*OVERSAMPLENR,200},
{128*OVERSAMPLENR,190},
{154*OVERSAMPLENR,180},
{184*OVERSAMPLENR,170},
{221*OVERSAMPLENR,160},
{265*OVERSAMPLENR,150},
{316*OVERSAMPLENR,140},
{375*OVERSAMPLENR,130},
{441*OVERSAMPLENR,120},
{513*OVERSAMPLENR,110},
{588*OVERSAMPLENR,100},
{734*OVERSAMPLENR,80},
{856*OVERSAMPLENR,60},
{938*OVERSAMPLENR,40},
{986*OVERSAMPLENR,20},
{1008*OVERSAMPLENR,0},
{1018*OVERSAMPLENR,-20}
};
#endif
#if (THERMISTORHEATER_1 == 4) || (THERMISTORHEATER_2 == 4) || (THERMISTORBED == 4) //10k thermistor

2
Marlin/ultralcd.h
Unescape View File

@ -153,4 +153,4 @@
#define BLOCK ;
#endif
#endif //ULTRALCD

3186
Marlin/ultralcd.pde
View File

File diff suppressed because it is too large Load Diff

64
README
Unescape View File

@ -1,7 +1,14 @@
This firmware is a mashup between Sprinter, grbl and many original parts.
This RepRap firmware is a mashup between Sprinter, grbl and many original parts.
(https://github.com/kliment/Sprinter)
(https://github.com/simen/grbl/tree)
Derived from Sprinter and Grbl by Erik van der Zalm.
Sprinters lead developers are Kliment and caru.
Grbls lead developer is Simen Svale Skogsrud.
It has been adapted to the Ultimaker Printer by:
Bernhard Kubicek, Matthijs Keuper, Bradley Feldman, and others...
Features:
- Interrupt based movement with real linear acceleration
- High steprate
@ -9,62 +16,49 @@ Features:
- Interrupt based temperature protection
- preliminary support for Matthew Roberts advance algorithm
For more info see: http://reprap.org/pipermail/reprap-dev/2011-May/003323.html
- Full endstop support
- Simple LCD support (16x2)
- SD Card support
- Provisions for Bernhard Kubicek's new hardware control console and 20x4 lcd
This firmware is optimized for Ultimaker's gen6 electronics (including the Ultimaker 1.5.x daughterboard and Arduino Mega 2560).
This firmware is optimized for gen6 electronics.
The default baudrate is 115200.
The default baudrate is 250000.
This gives less communication errors then regular baudrates.
========================================================================================
Configuring and compilation
Install the arduino software version 0018
Install the latest arduino software IDE/toolset (currently 0022)
http://www.arduino.cc/en/Main/Software
Install the sanguino software, version 0018
http://sanguino.cc/useit
Install Ultimaker's RepG 25 build
http://software.ultimaker.com
(or alternatively install Kliment's printrun/pronterface https://github.com/kliment/Printrun_)
Install pronterface
https://github.com/kliment/Printrun
Copy the Marlin firmware
https:/github.com/ErikZalm/Marlin
Copy the Ultimaker Marlin firmware
https:/github.com/bkubicek/Marlin
(Use the download button)
Start the arduino IDE.
Select Tools -> Board -> Sanguino
Select Tools -> Board -> Arduino Mega 2560
Select the correct serial port in Tools ->Serial Port
Open Marlin.pde
Change the printer specific setting in Configuration.h to the correct values.
The following values are the most important:
- float axis_steps_per_unit[].... // Set the correct steps / mm in the corresponding field
- const bool ENDSTOPS_INVERTING = false; // Change if only positive moves are executed
- #define INVERT_x_DIR true // Change if the motor direction is wrong
Click the Verify/Compile button
Click the Upload button
If all goes well the firmware is uploading
Start pronterface
Select the correct Serial Port. Type 250000 in the baudrate field.
Press the Connect button
===============================================================================================
Known issues
On some systems we get compilation errors.
This is caused by the "wiring_serial.c" and "wiring.c".
The simple fix is to delete these files but this may have a performance impact.
The best workaround is to move these files to sanguino directory.
(".../arduino-0018/hardware/Sanguino/cores/arduino/" on windows systems)
Start Ultimaker's Custom RepG 25
Make sure Show Experimental Profiles is enabled in Preferences
Select Sprinter as the Driver
Press the Connect button.
KNOWN ISSUES: RepG will display: Unknown: marlin x.y.z
That's ok. Enjoy Silky Smooth Printing.

69
README.md
Unescape View File

@ -0,0 +1,69 @@
WARNING: THIS IN A PROCESS OF HEAVY OVERWORKING.
DO NOT USE THIS ON YOUR MACHINE UNTIL FURTHER NOTICE!!!
===========================================
This RepRap firmware is a mashup between <a href="https://github.com/kliment/Sprinter">Sprinter</a>, <a href="https://github.com/simen/grbl/tree">grbl</a> and many original parts.
Derived from Sprinter and Grbl by Erik van der Zalm.
Sprinters lead developers are Kliment and caru.
Grbls lead developer is Simen Svale Skogsrud.
Some features have been added by and configuration has been added by:
Bernhard Kubicek, Matthijs Keuper, Bradley Feldman, and others...
Features:
- Interrupt based movement with real linear acceleration
- High steprate
- Look ahead (Keep the speed high when possible. High cornering speed)
- Interrupt based temperature protection
- preliminary support for Matthew Roberts advance algorithm
For more info see: http://reprap.org/pipermail/reprap-dev/2011-May/003323.html
- Full endstop support
- Simple LCD support (16x2)
- SD Card support
- Provisions for Bernhard Kubicek's new hardware control console and 20x4 lcd
This firmware is optimized for Ultimaker's gen6 electronics (including the Ultimaker 1.5.x daughterboard and Arduino Mega 2560).
The default baudrate is 115200.
========================================================================================
Configuring and compilation
Install the latest arduino software IDE/toolset (currently 0022)
http://www.arduino.cc/en/Main/Software
Install Ultimaker's RepG 25 build
http://software.ultimaker.com
(or alternatively install Kliment's printrun/pronterface https://github.com/kliment/Printrun_)
Copy the Ultimaker Marlin firmware
https:/github.com/bkubicek/Marlin
(Use the download button)
Start the arduino IDE.
Select Tools -> Board -> Arduino Mega 2560
Select the correct serial port in Tools ->Serial Port
Open Marlin.pde
Click the Verify/Compile button
Click the Upload button
If all goes well the firmware is uploading
Start Ultimaker's Custom RepG 25
Make sure Show Experimental Profiles is enabled in Preferences
Select Sprinter as the Driver
Press the Connect button.
KNOWN ISSUES: RepG will display: Unknown: marlin x.y.z
That's ok. Enjoy Silky Smooth Printing.

58
merging still needs.txt
Unescape View File

@ -0,0 +1,58 @@
files to compare manually:
planner.cpp
stepper.cpp
temperature.cpp
---
things that changed:
* planner.cpp
estimate_acc_distance now works with floats.
in calculate_trapezoid:for_block
long acceleration_rate=(long)((float)acceleration*8.388608) is gone
so is block_>acceleration_rate
void planner_reverse_pass:
some stuff I don't understand right now changed
in planner_forward_pass:
done: BLOCK_BUFFER_SIZE is now necessarily power of 2 (aka 8 16, 32). Inportant to document this somewhere.
no more inline in void plan_discard_current_block()
no more inline in plan_get_current_block()
in plan_buffer_line(...)
the long target[4]; and calculations of thoose should go after the while(block_buffer_tail==..). if the axis_steps_per_unit are changed from the gcode (M92) the calculation for the currently planned buffer move will be corrupt, because Target is calculated with one value, and the stuff afterwards with another. At least this solved the problem I had with the M92 E* changes in the code. Very sure about this, I took me 20min to find this as the solution for the bug I was hunting.
around if(feed_rate<minimumfeedrate) this only should be done if it is not a pure extrusion. I think there is a bug right now.
~line 447 blockcount=
not sure if this also works if the difference is negative, as it would happen if the ringbuffer runs over the end and start at 0.
~line 507 tmp_aceleration. not sure whats going on, but a lot changed.
* stepper.cpp
~214: if (busy) should be a echoln, maybe
~331: great, The Z_M_PIN checks are in :)
*temperature.cpp
done: enum for heater, bed,
manage_heater() is seriously different.
done: if tem_meas_ready ==true->!true+return?
done #define K1 0.95 maybe in the configuration.h?
semi-done: PID-C checking needed. Untested but added.
----
still needed to finish the merge, before testin!
manage_heater
ISR
movement planner
TODO:
remove traveling at maxpseed
remove Simplelcd
remove DEBUG_STEPS?
block_t
pid_dt ->0.1 whats the changes to the PID, checking needed
----
second merge saturday morning:
done: PID_dt->0.1
Write Preview
Loading…
Cancel
Save