diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index 51141fc3c..cba6f9fb6 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -137,7 +137,7 @@ #if ENABLED(Z_DUAL_STEPPER_DRIVERS) // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper. - // That way the machine is capable to align the bed during home, since both Z steppers are homed. + // That way the machine is capable to align the bed during home, since both Z steppers are homed. // There is also an implementation of M666 (software endstops adjustment) to this feature. // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed. // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2. @@ -335,8 +335,8 @@ // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT // we don't have a big font for Cyrillic, Kana //#define USE_BIG_EDIT_FONT - - // If you have spare 2300Byte of progmem and want to use a + + // If you have spare 2300Byte of progmem and want to use a // smaller font on the Info-screen uncomment the next line. //#define USE_SMALL_INFOFONT #endif // DOGLCD @@ -347,10 +347,10 @@ //#define USE_WATCHDOG #if ENABLED(USE_WATCHDOG) -// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. -// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. -// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. -//#define WATCHDOG_RESET_MANUAL + // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. + // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. + // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. + //#define WATCHDOG_RESET_MANUAL #endif // @section lcd @@ -389,7 +389,7 @@ #define MM_PER_ARC_SEGMENT 1 #define N_ARC_CORRECTION 25 -const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement +const unsigned int dropsegments = 5; //everything with less than this number of steps will be ignored as move and joined with the next movement // @section temperature @@ -461,7 +461,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st #endif /******************************************************************************\ - * enable this section if you have TMC26X motor drivers. + * enable this section if you have TMC26X motor drivers. * you need to import the TMC26XStepper library into the arduino IDE for this ******************************************************************************/ @@ -470,60 +470,60 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_TMCDRIVER #if ENABLED(HAVE_TMCDRIVER) -//#define X_IS_TMC + //#define X_IS_TMC #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps - -//#define X2_IS_TMC + + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps - -//#define Y_IS_TMC + + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps - -//#define Y2_IS_TMC + + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms - #define Y2_MICROSTEPS 16 //number of microsteps - -//#define Z_IS_TMC + #define Y2_MICROSTEPS 16 //number of microsteps + + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps - -//#define Z2_IS_TMC + + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps - -//#define E0_IS_TMC + + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps - -//#define E1_IS_TMC + + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms - #define E1_MICROSTEPS 16 //number of microsteps - -//#define E2_IS_TMC + #define E1_MICROSTEPS 16 //number of microsteps + + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms - #define E2_MICROSTEPS 16 //number of microsteps - -//#define E3_IS_TMC + #define E2_MICROSTEPS 16 //number of microsteps + + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms - #define E3_MICROSTEPS 16 //number of microsteps + #define E3_MICROSTEPS 16 //number of microsteps #endif /******************************************************************************\ - * enable this section if you have L6470 motor drivers. + * enable this section if you have L6470 motor drivers. * you need to import the L6470 library into the arduino IDE for this ******************************************************************************/ @@ -532,69 +532,66 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_L6470DRIVER #if ENABLED(HAVE_L6470DRIVER) -//#define X_IS_L6470 + //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps - #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall - -//#define X2_IS_L6470 + + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps - #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - -//#define Y_IS_L6470 + + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps - #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall - -//#define Y2_IS_L6470 - #define Y2_MICROSTEPS 16 //number of microsteps - #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + + //#define Y2_IS_L6470 + #define Y2_MICROSTEPS 16 //number of microsteps + #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off - #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - -//#define Z_IS_L6470 + #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall + + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps - #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall - -//#define Z2_IS_L6470 + + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps - #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - -//#define E0_IS_L6470 + + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps - #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall - -//#define E1_IS_L6470 - #define E1_MICROSTEPS 16 //number of microsteps + + //#define E1_IS_L6470 #define E1_MICROSTEPS 16 //number of microsteps - #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall - -//#define E2_IS_L6470 - #define E2_MICROSTEPS 16 //number of microsteps + + //#define E2_IS_L6470 #define E2_MICROSTEPS 16 //number of microsteps - #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - -//#define E3_IS_L6470 - #define E3_MICROSTEPS 16 //number of microsteps + + //#define E3_IS_L6470 #define E3_MICROSTEPS 16 //number of microsteps - #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #endif #include "Conditionals.h" diff --git a/Marlin/example_configurations/Felix/Configuration_adv.h b/Marlin/example_configurations/Felix/Configuration_adv.h index 5e9c5ea8c..b529d9ee1 100644 --- a/Marlin/example_configurations/Felix/Configuration_adv.h +++ b/Marlin/example_configurations/Felix/Configuration_adv.h @@ -356,10 +356,10 @@ //#define USE_WATCHDOG #if ENABLED(USE_WATCHDOG) -// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. -// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. -// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. -//#define WATCHDOG_RESET_MANUAL + // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. + // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. + // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. + //#define WATCHDOG_RESET_MANUAL #endif // @section lcd @@ -397,7 +397,7 @@ #define MM_PER_ARC_SEGMENT 1 #define N_ARC_CORRECTION 25 -const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement +const unsigned int dropsegments = 5; //everything with less than this number of steps will be ignored as move and joined with the next movement // @section temperature @@ -475,52 +475,52 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_TMCDRIVER #if ENABLED(HAVE_TMCDRIVER) -//#define X_IS_TMC + //#define X_IS_TMC #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps -//#define X2_IS_TMC + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps -//#define Y_IS_TMC + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps -//#define Y2_IS_TMC + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms #define Y2_MICROSTEPS 16 //number of microsteps -//#define Z_IS_TMC + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps -//#define Z2_IS_TMC + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps -//#define E0_IS_TMC + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps -//#define E1_IS_TMC + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms #define E1_MICROSTEPS 16 //number of microsteps -//#define E2_IS_TMC + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms #define E2_MICROSTEPS 16 //number of microsteps -//#define E3_IS_TMC + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms #define E3_MICROSTEPS 16 //number of microsteps @@ -537,61 +537,61 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_L6470DRIVER #if ENABLED(HAVE_L6470DRIVER) -//#define X_IS_L6470 + //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define X2_IS_L6470 + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y_IS_L6470 + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y2_IS_L6470 + //#define Y2_IS_L6470 #define Y2_MICROSTEPS 16 //number of microsteps #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z_IS_L6470 + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z2_IS_L6470 + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E0_IS_L6470 + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E1_IS_L6470 + //#define E1_IS_L6470 #define E1_MICROSTEPS 16 //number of microsteps #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E2_IS_L6470 + //#define E2_IS_L6470 #define E2_MICROSTEPS 16 //number of microsteps #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E3_IS_L6470 + //#define E3_IS_L6470 #define E3_MICROSTEPS 16 //number of microsteps #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off diff --git a/Marlin/example_configurations/Hephestos/Configuration_adv.h b/Marlin/example_configurations/Hephestos/Configuration_adv.h index 13f402c63..59bf7e018 100644 --- a/Marlin/example_configurations/Hephestos/Configuration_adv.h +++ b/Marlin/example_configurations/Hephestos/Configuration_adv.h @@ -356,10 +356,10 @@ //#define USE_WATCHDOG #if ENABLED(USE_WATCHDOG) -// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. -// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. -// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. -//#define WATCHDOG_RESET_MANUAL + // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. + // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. + // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. + //#define WATCHDOG_RESET_MANUAL #endif // @section lcd @@ -397,7 +397,7 @@ #define MM_PER_ARC_SEGMENT 1 #define N_ARC_CORRECTION 25 -const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement +const unsigned int dropsegments = 5; //everything with less than this number of steps will be ignored as move and joined with the next movement // @section temperature @@ -475,52 +475,52 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_TMCDRIVER #if ENABLED(HAVE_TMCDRIVER) -//#define X_IS_TMC + //#define X_IS_TMC #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps -//#define X2_IS_TMC + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps -//#define Y_IS_TMC + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps -//#define Y2_IS_TMC + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms #define Y2_MICROSTEPS 16 //number of microsteps -//#define Z_IS_TMC + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps -//#define Z2_IS_TMC + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps -//#define E0_IS_TMC + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps -//#define E1_IS_TMC + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms #define E1_MICROSTEPS 16 //number of microsteps -//#define E2_IS_TMC + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms #define E2_MICROSTEPS 16 //number of microsteps -//#define E3_IS_TMC + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms #define E3_MICROSTEPS 16 //number of microsteps @@ -537,61 +537,61 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_L6470DRIVER #if ENABLED(HAVE_L6470DRIVER) -//#define X_IS_L6470 + //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define X2_IS_L6470 + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y_IS_L6470 + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y2_IS_L6470 + //#define Y2_IS_L6470 #define Y2_MICROSTEPS 16 //number of microsteps #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z_IS_L6470 + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z2_IS_L6470 + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E0_IS_L6470 + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E1_IS_L6470 + //#define E1_IS_L6470 #define E1_MICROSTEPS 16 //number of microsteps #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E2_IS_L6470 + //#define E2_IS_L6470 #define E2_MICROSTEPS 16 //number of microsteps #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E3_IS_L6470 + //#define E3_IS_L6470 #define E3_MICROSTEPS 16 //number of microsteps #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off diff --git a/Marlin/example_configurations/K8200/Configuration_adv.h b/Marlin/example_configurations/K8200/Configuration_adv.h index c0e058d5e..1bf4103c7 100644 --- a/Marlin/example_configurations/K8200/Configuration_adv.h +++ b/Marlin/example_configurations/K8200/Configuration_adv.h @@ -356,10 +356,10 @@ //#define USE_WATCHDOG #if ENABLED(USE_WATCHDOG) -// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. -// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. -// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. -//#define WATCHDOG_RESET_MANUAL + // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. + // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. + // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. + //#define WATCHDOG_RESET_MANUAL #endif // @section lcd @@ -397,7 +397,7 @@ #define MM_PER_ARC_SEGMENT 1 #define N_ARC_CORRECTION 25 -const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement +const unsigned int dropsegments = 5; //everything with less than this number of steps will be ignored as move and joined with the next movement // @section temperature @@ -475,52 +475,52 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_TMCDRIVER #if ENABLED(HAVE_TMCDRIVER) -//#define X_IS_TMC + //#define X_IS_TMC #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps -//#define X2_IS_TMC + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps -//#define Y_IS_TMC + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps -//#define Y2_IS_TMC + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms #define Y2_MICROSTEPS 16 //number of microsteps -//#define Z_IS_TMC + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps -//#define Z2_IS_TMC + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps -//#define E0_IS_TMC + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps -//#define E1_IS_TMC + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms #define E1_MICROSTEPS 16 //number of microsteps -//#define E2_IS_TMC + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms #define E2_MICROSTEPS 16 //number of microsteps -//#define E3_IS_TMC + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms #define E3_MICROSTEPS 16 //number of microsteps @@ -537,61 +537,61 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_L6470DRIVER #if ENABLED(HAVE_L6470DRIVER) -//#define X_IS_L6470 + //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define X2_IS_L6470 + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y_IS_L6470 + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y2_IS_L6470 + //#define Y2_IS_L6470 #define Y2_MICROSTEPS 16 //number of microsteps #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z_IS_L6470 + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z2_IS_L6470 + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E0_IS_L6470 + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E1_IS_L6470 + //#define E1_IS_L6470 #define E1_MICROSTEPS 16 //number of microsteps #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E2_IS_L6470 + //#define E2_IS_L6470 #define E2_MICROSTEPS 16 //number of microsteps #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E3_IS_L6470 + //#define E3_IS_L6470 #define E3_MICROSTEPS 16 //number of microsteps #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off diff --git a/Marlin/example_configurations/RigidBot/Configuration_adv.h b/Marlin/example_configurations/RigidBot/Configuration_adv.h index 0abad2e5d..fe8e2db97 100644 --- a/Marlin/example_configurations/RigidBot/Configuration_adv.h +++ b/Marlin/example_configurations/RigidBot/Configuration_adv.h @@ -348,10 +348,10 @@ //#define USE_WATCHDOG #if ENABLED(USE_WATCHDOG) -// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. -// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. -// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. -//#define WATCHDOG_RESET_MANUAL + // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. + // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. + // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. + //#define WATCHDOG_RESET_MANUAL #endif // @section lcd @@ -389,7 +389,7 @@ #define MM_PER_ARC_SEGMENT 1 #define N_ARC_CORRECTION 25 -const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement +const unsigned int dropsegments = 5; //everything with less than this number of steps will be ignored as move and joined with the next movement // @section temperature @@ -470,52 +470,52 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_TMCDRIVER #if ENABLED(HAVE_TMCDRIVER) -//#define X_IS_TMC + //#define X_IS_TMC #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps -//#define X2_IS_TMC + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps -//#define Y_IS_TMC + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps -//#define Y2_IS_TMC + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms #define Y2_MICROSTEPS 16 //number of microsteps -//#define Z_IS_TMC + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps -//#define Z2_IS_TMC + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps -//#define E0_IS_TMC + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps -//#define E1_IS_TMC + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms #define E1_MICROSTEPS 16 //number of microsteps -//#define E2_IS_TMC + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms #define E2_MICROSTEPS 16 //number of microsteps -//#define E3_IS_TMC + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms #define E3_MICROSTEPS 16 //number of microsteps @@ -532,61 +532,61 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_L6470DRIVER #if ENABLED(HAVE_L6470DRIVER) -//#define X_IS_L6470 + //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define X2_IS_L6470 + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y_IS_L6470 + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y2_IS_L6470 + //#define Y2_IS_L6470 #define Y2_MICROSTEPS 16 //number of microsteps #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z_IS_L6470 + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z2_IS_L6470 + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E0_IS_L6470 + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E1_IS_L6470 + //#define E1_IS_L6470 #define E1_MICROSTEPS 16 //number of microsteps #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E2_IS_L6470 + //#define E2_IS_L6470 #define E2_MICROSTEPS 16 //number of microsteps #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E3_IS_L6470 + //#define E3_IS_L6470 #define E3_MICROSTEPS 16 //number of microsteps #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off diff --git a/Marlin/example_configurations/SCARA/Configuration_adv.h b/Marlin/example_configurations/SCARA/Configuration_adv.h index eb64a0d6b..7866b7da3 100644 --- a/Marlin/example_configurations/SCARA/Configuration_adv.h +++ b/Marlin/example_configurations/SCARA/Configuration_adv.h @@ -356,10 +356,10 @@ //#define USE_WATCHDOG #if ENABLED(USE_WATCHDOG) -// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. -// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. -// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. -//#define WATCHDOG_RESET_MANUAL + // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. + // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. + // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. + //#define WATCHDOG_RESET_MANUAL #endif // @section lcd @@ -397,7 +397,7 @@ #define MM_PER_ARC_SEGMENT 1 #define N_ARC_CORRECTION 25 -const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement +const unsigned int dropsegments = 5; //everything with less than this number of steps will be ignored as move and joined with the next movement // @section temperature @@ -475,52 +475,52 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_TMCDRIVER #if ENABLED(HAVE_TMCDRIVER) -//#define X_IS_TMC + //#define X_IS_TMC #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps -//#define X2_IS_TMC + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps -//#define Y_IS_TMC + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps -//#define Y2_IS_TMC + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms #define Y2_MICROSTEPS 16 //number of microsteps -//#define Z_IS_TMC + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps -//#define Z2_IS_TMC + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps -//#define E0_IS_TMC + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps -//#define E1_IS_TMC + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms #define E1_MICROSTEPS 16 //number of microsteps -//#define E2_IS_TMC + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms #define E2_MICROSTEPS 16 //number of microsteps -//#define E3_IS_TMC + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms #define E3_MICROSTEPS 16 //number of microsteps @@ -537,61 +537,61 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_L6470DRIVER #if ENABLED(HAVE_L6470DRIVER) -//#define X_IS_L6470 + //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define X2_IS_L6470 + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y_IS_L6470 + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y2_IS_L6470 + //#define Y2_IS_L6470 #define Y2_MICROSTEPS 16 //number of microsteps #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z_IS_L6470 + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z2_IS_L6470 + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E0_IS_L6470 + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E1_IS_L6470 + //#define E1_IS_L6470 #define E1_MICROSTEPS 16 //number of microsteps #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E2_IS_L6470 + //#define E2_IS_L6470 #define E2_MICROSTEPS 16 //number of microsteps #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E3_IS_L6470 + //#define E3_IS_L6470 #define E3_MICROSTEPS 16 //number of microsteps #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off diff --git a/Marlin/example_configurations/TAZ4/Configuration_adv.h b/Marlin/example_configurations/TAZ4/Configuration_adv.h index b4e4539fe..ee7fbcf94 100644 --- a/Marlin/example_configurations/TAZ4/Configuration_adv.h +++ b/Marlin/example_configurations/TAZ4/Configuration_adv.h @@ -355,10 +355,10 @@ //#define USE_WATCHDOG #if ENABLED(USE_WATCHDOG) -// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. -// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. -// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. -//#define WATCHDOG_RESET_MANUAL + // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. + // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. + // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. + //#define WATCHDOG_RESET_MANUAL #endif // @section lcd @@ -397,7 +397,7 @@ #define MM_PER_ARC_SEGMENT 1 #define N_ARC_CORRECTION 25 -const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement +const unsigned int dropsegments = 5; //everything with less than this number of steps will be ignored as move and joined with the next movement // @section temperature @@ -478,52 +478,52 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_TMCDRIVER #if ENABLED(HAVE_TMCDRIVER) -//#define X_IS_TMC + //#define X_IS_TMC #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps -//#define X2_IS_TMC + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps -//#define Y_IS_TMC + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps -//#define Y2_IS_TMC + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms #define Y2_MICROSTEPS 16 //number of microsteps -//#define Z_IS_TMC + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps -//#define Z2_IS_TMC + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps -//#define E0_IS_TMC + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps -//#define E1_IS_TMC + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms #define E1_MICROSTEPS 16 //number of microsteps -//#define E2_IS_TMC + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms #define E2_MICROSTEPS 16 //number of microsteps -//#define E3_IS_TMC + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms #define E3_MICROSTEPS 16 //number of microsteps @@ -540,61 +540,61 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_L6470DRIVER #if ENABLED(HAVE_L6470DRIVER) -//#define X_IS_L6470 + //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define X2_IS_L6470 + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y_IS_L6470 + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y2_IS_L6470 + //#define Y2_IS_L6470 #define Y2_MICROSTEPS 16 //number of microsteps #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z_IS_L6470 + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z2_IS_L6470 + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E0_IS_L6470 + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E1_IS_L6470 + //#define E1_IS_L6470 #define E1_MICROSTEPS 16 //number of microsteps #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E2_IS_L6470 + //#define E2_IS_L6470 #define E2_MICROSTEPS 16 //number of microsteps #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E3_IS_L6470 + //#define E3_IS_L6470 #define E3_MICROSTEPS 16 //number of microsteps #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off diff --git a/Marlin/example_configurations/WITBOX/Configuration_adv.h b/Marlin/example_configurations/WITBOX/Configuration_adv.h index 3a006b58c..cf6b6faa3 100644 --- a/Marlin/example_configurations/WITBOX/Configuration_adv.h +++ b/Marlin/example_configurations/WITBOX/Configuration_adv.h @@ -356,10 +356,10 @@ //#define USE_WATCHDOG #if ENABLED(USE_WATCHDOG) -// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. -// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. -// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. -//#define WATCHDOG_RESET_MANUAL + // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. + // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. + // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. + //#define WATCHDOG_RESET_MANUAL #endif // @section lcd @@ -397,7 +397,7 @@ #define MM_PER_ARC_SEGMENT 1 #define N_ARC_CORRECTION 25 -const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement +const unsigned int dropsegments = 5; //everything with less than this number of steps will be ignored as move and joined with the next movement // @section temperature @@ -475,52 +475,52 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_TMCDRIVER #if ENABLED(HAVE_TMCDRIVER) -//#define X_IS_TMC + //#define X_IS_TMC #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps -//#define X2_IS_TMC + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps -//#define Y_IS_TMC + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps -//#define Y2_IS_TMC + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms #define Y2_MICROSTEPS 16 //number of microsteps -//#define Z_IS_TMC + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps -//#define Z2_IS_TMC + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps -//#define E0_IS_TMC + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps -//#define E1_IS_TMC + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms #define E1_MICROSTEPS 16 //number of microsteps -//#define E2_IS_TMC + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms #define E2_MICROSTEPS 16 //number of microsteps -//#define E3_IS_TMC + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms #define E3_MICROSTEPS 16 //number of microsteps @@ -537,61 +537,61 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_L6470DRIVER #if ENABLED(HAVE_L6470DRIVER) -//#define X_IS_L6470 + //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define X2_IS_L6470 + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y_IS_L6470 + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y2_IS_L6470 + //#define Y2_IS_L6470 #define Y2_MICROSTEPS 16 //number of microsteps #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z_IS_L6470 + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z2_IS_L6470 + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E0_IS_L6470 + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E1_IS_L6470 + //#define E1_IS_L6470 #define E1_MICROSTEPS 16 //number of microsteps #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E2_IS_L6470 + //#define E2_IS_L6470 #define E2_MICROSTEPS 16 //number of microsteps #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E3_IS_L6470 + //#define E3_IS_L6470 #define E3_MICROSTEPS 16 //number of microsteps #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h index 26ed97b22..96c861449 100644 --- a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h +++ b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h @@ -357,10 +357,10 @@ //#define USE_WATCHDOG #if ENABLED(USE_WATCHDOG) -// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. -// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. -// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. -//#define WATCHDOG_RESET_MANUAL + // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. + // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. + // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. + //#define WATCHDOG_RESET_MANUAL #endif // @section lcd @@ -398,7 +398,7 @@ #define MM_PER_ARC_SEGMENT 1 #define N_ARC_CORRECTION 25 -const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement +const unsigned int dropsegments = 5; //everything with less than this number of steps will be ignored as move and joined with the next movement // @section temperature @@ -476,52 +476,52 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_TMCDRIVER #if ENABLED(HAVE_TMCDRIVER) -//#define X_IS_TMC + //#define X_IS_TMC #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps -//#define X2_IS_TMC + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps -//#define Y_IS_TMC + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps -//#define Y2_IS_TMC + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms #define Y2_MICROSTEPS 16 //number of microsteps -//#define Z_IS_TMC + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps -//#define Z2_IS_TMC + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps -//#define E0_IS_TMC + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps -//#define E1_IS_TMC + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms #define E1_MICROSTEPS 16 //number of microsteps -//#define E2_IS_TMC + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms #define E2_MICROSTEPS 16 //number of microsteps -//#define E3_IS_TMC + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms #define E3_MICROSTEPS 16 //number of microsteps @@ -538,61 +538,61 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_L6470DRIVER #if ENABLED(HAVE_L6470DRIVER) -//#define X_IS_L6470 + //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define X2_IS_L6470 + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y_IS_L6470 + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y2_IS_L6470 + //#define Y2_IS_L6470 #define Y2_MICROSTEPS 16 //number of microsteps #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z_IS_L6470 + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z2_IS_L6470 + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E0_IS_L6470 + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E1_IS_L6470 + //#define E1_IS_L6470 #define E1_MICROSTEPS 16 //number of microsteps #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E2_IS_L6470 + //#define E2_IS_L6470 #define E2_MICROSTEPS 16 //number of microsteps #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E3_IS_L6470 + //#define E3_IS_L6470 #define E3_MICROSTEPS 16 //number of microsteps #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off diff --git a/Marlin/example_configurations/delta/generic/Configuration_adv.h b/Marlin/example_configurations/delta/generic/Configuration_adv.h index dc7757748..653946603 100644 --- a/Marlin/example_configurations/delta/generic/Configuration_adv.h +++ b/Marlin/example_configurations/delta/generic/Configuration_adv.h @@ -358,10 +358,10 @@ //#define USE_WATCHDOG #if ENABLED(USE_WATCHDOG) -// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. -// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. -// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. -//#define WATCHDOG_RESET_MANUAL + // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. + // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. + // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. + //#define WATCHDOG_RESET_MANUAL #endif // @section lcd @@ -399,7 +399,7 @@ #define MM_PER_ARC_SEGMENT 1 #define N_ARC_CORRECTION 25 -const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement +const unsigned int dropsegments = 5; //everything with less than this number of steps will be ignored as move and joined with the next movement // @section temperature @@ -477,52 +477,52 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_TMCDRIVER #if ENABLED(HAVE_TMCDRIVER) -//#define X_IS_TMC + //#define X_IS_TMC #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps -//#define X2_IS_TMC + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps -//#define Y_IS_TMC + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps -//#define Y2_IS_TMC + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms #define Y2_MICROSTEPS 16 //number of microsteps -//#define Z_IS_TMC + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps -//#define Z2_IS_TMC + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps -//#define E0_IS_TMC + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps -//#define E1_IS_TMC + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms #define E1_MICROSTEPS 16 //number of microsteps -//#define E2_IS_TMC + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms #define E2_MICROSTEPS 16 //number of microsteps -//#define E3_IS_TMC + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms #define E3_MICROSTEPS 16 //number of microsteps @@ -539,61 +539,61 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_L6470DRIVER #if ENABLED(HAVE_L6470DRIVER) -//#define X_IS_L6470 + //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define X2_IS_L6470 + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y_IS_L6470 + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y2_IS_L6470 + //#define Y2_IS_L6470 #define Y2_MICROSTEPS 16 //number of microsteps #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z_IS_L6470 + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z2_IS_L6470 + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E0_IS_L6470 + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E1_IS_L6470 + //#define E1_IS_L6470 #define E1_MICROSTEPS 16 //number of microsteps #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E2_IS_L6470 + //#define E2_IS_L6470 #define E2_MICROSTEPS 16 //number of microsteps #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E3_IS_L6470 + //#define E3_IS_L6470 #define E3_MICROSTEPS 16 //number of microsteps #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h index 95724e9e5..172519395 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h @@ -357,10 +357,10 @@ //#define USE_WATCHDOG #if ENABLED(USE_WATCHDOG) -// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. -// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. -// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. -//#define WATCHDOG_RESET_MANUAL + // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. + // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. + // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. + //#define WATCHDOG_RESET_MANUAL #endif // @section lcd @@ -398,7 +398,7 @@ #define MM_PER_ARC_SEGMENT 1 #define N_ARC_CORRECTION 25 -const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement +const unsigned int dropsegments = 5; //everything with less than this number of steps will be ignored as move and joined with the next movement // @section temperature @@ -476,52 +476,52 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_TMCDRIVER #if ENABLED(HAVE_TMCDRIVER) -//#define X_IS_TMC + //#define X_IS_TMC #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps -//#define X2_IS_TMC + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps -//#define Y_IS_TMC + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps -//#define Y2_IS_TMC + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms #define Y2_MICROSTEPS 16 //number of microsteps -//#define Z_IS_TMC + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps -//#define Z2_IS_TMC + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps -//#define E0_IS_TMC + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps -//#define E1_IS_TMC + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms #define E1_MICROSTEPS 16 //number of microsteps -//#define E2_IS_TMC + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms #define E2_MICROSTEPS 16 //number of microsteps -//#define E3_IS_TMC + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms #define E3_MICROSTEPS 16 //number of microsteps @@ -538,61 +538,61 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_L6470DRIVER #if ENABLED(HAVE_L6470DRIVER) -//#define X_IS_L6470 + //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define X2_IS_L6470 + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y_IS_L6470 + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y2_IS_L6470 + //#define Y2_IS_L6470 #define Y2_MICROSTEPS 16 //number of microsteps #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z_IS_L6470 + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z2_IS_L6470 + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E0_IS_L6470 + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E1_IS_L6470 + //#define E1_IS_L6470 #define E1_MICROSTEPS 16 //number of microsteps #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E2_IS_L6470 + //#define E2_IS_L6470 #define E2_MICROSTEPS 16 //number of microsteps #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E3_IS_L6470 + //#define E3_IS_L6470 #define E3_MICROSTEPS 16 //number of microsteps #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h index f500e4248..61373b3ed 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h @@ -361,10 +361,10 @@ //#define USE_WATCHDOG #if ENABLED(USE_WATCHDOG) -// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. -// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. -// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. -//#define WATCHDOG_RESET_MANUAL + // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. + // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. + // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. + //#define WATCHDOG_RESET_MANUAL #endif // @section lcd @@ -402,7 +402,7 @@ #define MM_PER_ARC_SEGMENT 1 #define N_ARC_CORRECTION 25 -const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement +const unsigned int dropsegments = 5; //everything with less than this number of steps will be ignored as move and joined with the next movement // @section temperature @@ -480,52 +480,52 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_TMCDRIVER #if ENABLED(HAVE_TMCDRIVER) -//#define X_IS_TMC + //#define X_IS_TMC #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps -//#define X2_IS_TMC + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps -//#define Y_IS_TMC + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps -//#define Y2_IS_TMC + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms #define Y2_MICROSTEPS 16 //number of microsteps -//#define Z_IS_TMC + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps -//#define Z2_IS_TMC + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps -//#define E0_IS_TMC + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps -//#define E1_IS_TMC + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms #define E1_MICROSTEPS 16 //number of microsteps -//#define E2_IS_TMC + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms #define E2_MICROSTEPS 16 //number of microsteps -//#define E3_IS_TMC + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms #define E3_MICROSTEPS 16 //number of microsteps @@ -542,61 +542,61 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_L6470DRIVER #if ENABLED(HAVE_L6470DRIVER) -//#define X_IS_L6470 + //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define X2_IS_L6470 + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y_IS_L6470 + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y2_IS_L6470 + //#define Y2_IS_L6470 #define Y2_MICROSTEPS 16 //number of microsteps #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z_IS_L6470 + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z2_IS_L6470 + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E0_IS_L6470 + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E1_IS_L6470 + //#define E1_IS_L6470 #define E1_MICROSTEPS 16 //number of microsteps #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E2_IS_L6470 + //#define E2_IS_L6470 #define E2_MICROSTEPS 16 //number of microsteps #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E3_IS_L6470 + //#define E3_IS_L6470 #define E3_MICROSTEPS 16 //number of microsteps #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off diff --git a/Marlin/example_configurations/makibox/Configuration_adv.h b/Marlin/example_configurations/makibox/Configuration_adv.h index c837be88d..6e5921dd3 100644 --- a/Marlin/example_configurations/makibox/Configuration_adv.h +++ b/Marlin/example_configurations/makibox/Configuration_adv.h @@ -355,10 +355,10 @@ //#define USE_WATCHDOG #if ENABLED(USE_WATCHDOG) -// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. -// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. -// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. -//#define WATCHDOG_RESET_MANUAL + // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. + // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. + // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. + //#define WATCHDOG_RESET_MANUAL #endif // @section lcd @@ -396,7 +396,7 @@ #define MM_PER_ARC_SEGMENT 1 #define N_ARC_CORRECTION 25 -const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement +const unsigned int dropsegments = 5; //everything with less than this number of steps will be ignored as move and joined with the next movement // @section temperature @@ -474,52 +474,52 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_TMCDRIVER #if ENABLED(HAVE_TMCDRIVER) -//#define X_IS_TMC + //#define X_IS_TMC #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps -//#define X2_IS_TMC + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps -//#define Y_IS_TMC + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps -//#define Y2_IS_TMC + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms #define Y2_MICROSTEPS 16 //number of microsteps -//#define Z_IS_TMC + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps -//#define Z2_IS_TMC + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps -//#define E0_IS_TMC + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps -//#define E1_IS_TMC + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms #define E1_MICROSTEPS 16 //number of microsteps -//#define E2_IS_TMC + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms #define E2_MICROSTEPS 16 //number of microsteps -//#define E3_IS_TMC + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms #define E3_MICROSTEPS 16 //number of microsteps @@ -536,61 +536,61 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_L6470DRIVER #if ENABLED(HAVE_L6470DRIVER) -//#define X_IS_L6470 + //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define X2_IS_L6470 + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y_IS_L6470 + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y2_IS_L6470 + //#define Y2_IS_L6470 #define Y2_MICROSTEPS 16 //number of microsteps #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z_IS_L6470 + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z2_IS_L6470 + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E0_IS_L6470 + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E1_IS_L6470 + //#define E1_IS_L6470 #define E1_MICROSTEPS 16 //number of microsteps #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E2_IS_L6470 + //#define E2_IS_L6470 #define E2_MICROSTEPS 16 //number of microsteps #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E3_IS_L6470 + //#define E3_IS_L6470 #define E3_MICROSTEPS 16 //number of microsteps #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h index 5facef82e..01b15afa4 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h @@ -356,10 +356,10 @@ //#define USE_WATCHDOG #if ENABLED(USE_WATCHDOG) -// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. -// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. -// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. -//#define WATCHDOG_RESET_MANUAL + // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. + // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. + // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. + //#define WATCHDOG_RESET_MANUAL #endif // @section lcd @@ -397,7 +397,7 @@ #define MM_PER_ARC_SEGMENT 1 #define N_ARC_CORRECTION 25 -const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement +const unsigned int dropsegments = 5; //everything with less than this number of steps will be ignored as move and joined with the next movement // @section temperature @@ -475,52 +475,52 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_TMCDRIVER #if ENABLED(HAVE_TMCDRIVER) -//#define X_IS_TMC + //#define X_IS_TMC #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps -//#define X2_IS_TMC + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps -//#define Y_IS_TMC + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps -//#define Y2_IS_TMC + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms #define Y2_MICROSTEPS 16 //number of microsteps -//#define Z_IS_TMC + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps -//#define Z2_IS_TMC + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps -//#define E0_IS_TMC + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps -//#define E1_IS_TMC + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms #define E1_MICROSTEPS 16 //number of microsteps -//#define E2_IS_TMC + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms #define E2_MICROSTEPS 16 //number of microsteps -//#define E3_IS_TMC + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms #define E3_MICROSTEPS 16 //number of microsteps @@ -537,61 +537,61 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HAVE_L6470DRIVER #if ENABLED(HAVE_L6470DRIVER) -//#define X_IS_L6470 + //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define X2_IS_L6470 + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y_IS_L6470 + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Y2_IS_L6470 + //#define Y2_IS_L6470 #define Y2_MICROSTEPS 16 //number of microsteps #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z_IS_L6470 + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define Z2_IS_L6470 + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E0_IS_L6470 + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E1_IS_L6470 + //#define E1_IS_L6470 #define E1_MICROSTEPS 16 //number of microsteps #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E2_IS_L6470 + //#define E2_IS_L6470 #define E2_MICROSTEPS 16 //number of microsteps #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall -//#define E3_IS_L6470 + //#define E3_IS_L6470 #define E3_MICROSTEPS 16 //number of microsteps #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off