From 0fca084ea688aed41b892f9cea7e069510c73c94 Mon Sep 17 00:00:00 2001 From: Scott Lahteine Date: Sun, 26 Apr 2015 18:44:01 -0700 Subject: [PATCH] Make EEPROM reproducible in GCode MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit With these changes the output of `M503 S0` is all you need to restore the EEPROM. Building on this it is straightforward to save and restore the EEPROM state using the SD card or external GCode file. - Added `M145` to set “heatup states” for the LCD menu - Added `M420` to toggle Mesh Bed Leveling - Added `M421` to set a single Mesh coordinate - Extended `Config_PrintSettings` with added M codes - Cleaned up some comments here and there --- Marlin/Configuration_adv.h | 2 +- Marlin/Marlin_main.cpp | 153 +++++++- Marlin/configuration_store.cpp | 334 +++++++++++------- .../configurator/config/Configuration_adv.h | 2 +- Marlin/configurator/config/language.h | 5 +- .../Felix/Configuration_adv.h | 2 +- .../Hephestos/Configuration_adv.h | 2 +- .../K8200/Configuration_adv.h | 2 +- .../SCARA/Configuration_adv.h | 2 +- .../WITBOX/Configuration_adv.h | 2 +- .../delta/generic/Configuration_adv.h | 2 +- .../delta/kossel_mini/Configuration_adv.h | 2 +- .../makibox/Configuration_adv.h | 2 +- .../tvrrug/Round2/Configuration_adv.h | 2 +- Marlin/language.h | 3 + Marlin/planner.cpp | 137 ++++--- Marlin/planner.h | 14 +- Marlin/temperature.cpp | 5 +- Marlin/ultralcd.cpp | 8 +- Marlin/watchdog.cpp | 6 +- 20 files changed, 453 insertions(+), 234 deletions(-) diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index 6478eb923..059f0c5c1 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -355,7 +355,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HEATERS_PARALLEL //=========================================================================== -//=============================Buffers ============================ +//================================= Buffers ================================= //=========================================================================== // @section hidden diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp index ac86cb05b..cbeb9a091 100644 --- a/Marlin/Marlin_main.cpp +++ b/Marlin/Marlin_main.cpp @@ -151,6 +151,7 @@ * M128 - EtoP Open (BariCUDA EtoP = electricity to air pressure transducer by jmil) * M129 - EtoP Closed (BariCUDA EtoP = electricity to air pressure transducer by jmil) * M140 - Set bed target temp + * M145 - Set the heatup state H B F for S (0=PLA, 1=ABS) * M150 - Set BlinkM Color Output R: Red<0-255> U(!): Green<0-255> B: Blue<0-255> over i2c, G for green does not work. * M190 - Sxxx Wait for bed current temp to reach target temp. Waits only when heating * Rxxx Wait for bed current temp to reach target temp. Waits when heating and cooling @@ -186,6 +187,8 @@ * M406 - Turn off Filament Sensor extrusion control * M407 - Display measured filament diameter * M410 - Quickstop. Abort all the planned moves + * M420 - Enable/Disable Mesh Leveling (with current values) S1=enable S0=disable + * M421 - Set a single Z coordinate in the Mesh Leveling grid. X Y Z * M500 - Store parameters in EEPROM * M501 - Read parameters from EEPROM (if you need reset them after you changed them temporarily). * M502 - Revert to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. @@ -3385,6 +3388,62 @@ inline void gcode_M140() { if (code_seen('S')) setTargetBed(code_value()); } +#ifdef ULTIPANEL + + /** + * M145: Set the heatup state for a material in the LCD menu + * S (0=PLA, 1=ABS) + * H + * B + * F + */ + inline void gcode_M145() { + uint8_t material = code_seen('S') ? code_value_short() : 0; + if (material < 0 || material > 1) { + SERIAL_ERROR_START; + SERIAL_ERRORLNPGM(MSG_ERR_MATERIAL_INDEX); + } + else { + int v; + switch (material) { + case 0: + if (code_seen('H')) { + v = code_value_short(); + plaPreheatHotendTemp = constrain(v, EXTRUDE_MINTEMP, HEATER_0_MAXTEMP - 15); + } + if (code_seen('F')) { + v = code_value_short(); + plaPreheatFanSpeed = constrain(v, 0, 255); + } + #if TEMP_SENSOR_BED != 0 + if (code_seen('B')) { + v = code_value_short(); + plaPreheatHPBTemp = constrain(v, BED_MINTEMP, BED_MAXTEMP - 15); + } + #endif + break; + case 1: + if (code_seen('H')) { + v = code_value_short(); + absPreheatHotendTemp = constrain(v, EXTRUDE_MINTEMP, HEATER_0_MAXTEMP - 15); + } + if (code_seen('F')) { + v = code_value_short(); + absPreheatFanSpeed = constrain(v, 0, 255); + } + #if TEMP_SENSOR_BED != 0 + if (code_seen('B')) { + v = code_value_short(); + absPreheatHPBTemp = constrain(v, BED_MINTEMP, BED_MAXTEMP - 15); + } + #endif + break; + } + } + } + +#endif + #if HAS_POWER_SWITCH /** @@ -3492,7 +3551,8 @@ inline void gcode_M85() { } /** - * M92: Set inactivity shutdown timer with parameter S. To disable set zero (default) + * M92: Set axis steps-per-unit for one or more axes, X, Y, Z, and E. + * (Follows the same syntax as G92) */ inline void gcode_M92() { for(int8_t i=0; i < NUM_AXIS; i++) { @@ -3814,20 +3874,35 @@ inline void gcode_M206() { #ifdef FWRETRACT /** - * M207: Set retract length S[positive mm] F[feedrate mm/min] Z[additional zlift/hop] + * M207: Set firmware retraction values + * + * S[+mm] retract_length + * W[+mm] retract_length_swap (multi-extruder) + * F[mm/min] retract_feedrate + * Z[mm] retract_zlift */ inline void gcode_M207() { if (code_seen('S')) retract_length = code_value(); if (code_seen('F')) retract_feedrate = code_value() / 60; if (code_seen('Z')) retract_zlift = code_value(); + #if EXTRUDERS > 1 + if (code_seen('W')) retract_length_swap = code_value(); + #endif } /** - * M208: Set retract recover length S[positive mm surplus to the M207 S*] F[feedrate mm/min] + * M208: Set firmware un-retraction values + * + * S[+mm] retract_recover_length (in addition to M207 S*) + * W[+mm] retract_recover_length_swap (multi-extruder) + * F[mm/min] retract_recover_feedrate */ inline void gcode_M208() { if (code_seen('S')) retract_recover_length = code_value(); if (code_seen('F')) retract_recover_feedrate = code_value() / 60; + #if EXTRUDERS > 1 + if (code_seen('W')) retract_recover_length_swap = code_value(); + #endif } /** @@ -4380,6 +4455,42 @@ inline void gcode_M400() { st_synchronize(); } */ inline void gcode_M410() { quickStop(); } + +#ifdef MESH_BED_LEVELING + + /** + * M420: Enable/Disable Mesh Bed Leveling + */ + inline void gcode_M420() { if (code_seen('S') && code_has_value()) mbl.active = !!code_value_short(); } + + /** + * M421: Set a single Mesh Bed Leveling Z coordinate + */ + inline void gcode_M421() { + int x, y; + float z; + bool err = false, hasX, hasY, hasZ; + if ((hasX = code_seen('X'))) x = code_value_short(); + if ((hasY = code_seen('Y'))) y = code_value_short(); + if ((hasZ = code_seen('Z'))) z = code_value(); + + if (!hasX || !hasY || !hasZ) { + SERIAL_ERROR_START; + SERIAL_ERRORLNPGM(MSG_ERR_XYZ_REQUIRED_FOR_M421); + err = true; + } + + if (x >= MESH_NUM_X_POINTS || y >= MESH_NUM_Y_POINTS) { + SERIAL_ERROR_START; + SERIAL_ERRORLNPGM(MSG_ERR_MESH_INDEX_OOB); + err = true; + } + + if (!err) mbl.z_values[y][x] = z; + } + +#endif + /** * M500: Store settings in EEPROM */ @@ -4934,11 +5045,11 @@ void process_commands() { gcode_M104(); break; - case 111: // M111: Set debug level + case 111: // M111: Set debug level gcode_M111(); break; - case 112: // M112: Emergency Stop + case 112: // M112: Emergency Stop gcode_M112(); break; @@ -5017,28 +5128,35 @@ void process_commands() { case 85: // M85 gcode_M85(); break; - case 92: // M92 + case 92: // M92: Set the steps-per-unit for one or more axes gcode_M92(); break; - case 115: // M115 + case 115: // M115: Report capabilities gcode_M115(); break; - case 117: // M117 display message + case 117: // M117: Set LCD message text gcode_M117(); break; - case 114: // M114 + case 114: // M114: Report current position gcode_M114(); break; - case 120: // M120 + case 120: // M120: Enable endstops gcode_M120(); break; - case 121: // M121 + case 121: // M121: Disable endstops gcode_M121(); break; - case 119: // M119 + case 119: // M119: Report endstop states gcode_M119(); break; - //TODO: update for all axis, use for loop + + #ifdef ULTIPANEL + + case 145: // M145: Set material heatup parameters + gcode_M145(); + break; + + #endif #ifdef BLINKM @@ -5213,6 +5331,15 @@ void process_commands() { gcode_M410(); break; + #ifdef MESH_BED_LEVELING + case 420: // M420 Enable/Disable Mesh Bed Leveling + gcode_M420(); + break; + case 421: // M421 Set a Mesh Bed Leveling Z coordinate + gcode_M421(); + break; + #endif + case 500: // M500 Store settings in EEPROM gcode_M500(); break; diff --git a/Marlin/configuration_store.cpp b/Marlin/configuration_store.cpp index 9f91db098..318501db6 100644 --- a/Marlin/configuration_store.cpp +++ b/Marlin/configuration_store.cpp @@ -20,72 +20,72 @@ * V19 EEPROM Layout: * * ver - * axis_steps_per_unit (x4) - * max_feedrate (x4) - * max_acceleration_units_per_sq_second (x4) - * acceleration - * retract_acceleration - * travel_acceleration - * minimumfeedrate - * mintravelfeedrate - * minsegmenttime - * max_xy_jerk - * max_z_jerk - * max_e_jerk - * home_offset (x3) + * M92 XYZE axis_steps_per_unit (x4) + * M203 XYZE max_feedrate (x4) + * M201 XYZE max_acceleration_units_per_sq_second (x4) + * M204 P acceleration + * M204 R retract_acceleration + * M204 T travel_acceleration + * M205 S minimumfeedrate + * M205 T mintravelfeedrate + * M205 B minsegmenttime + * M205 X max_xy_jerk + * M205 Z max_z_jerk + * M205 E max_e_jerk + * M206 XYZ home_offset (x3) * * Mesh bed leveling: - * active - * mesh_num_x - * mesh_num_y - * z_values[][] - * zprobe_zoffset + * M420 S active + * mesh_num_x (set in firmware) + * mesh_num_y (set in firmware) + * M421 XYZ z_values[][] + * M851 zprobe_zoffset * * DELTA: - * endstop_adj (x3) - * delta_radius - * delta_diagonal_rod - * delta_segments_per_second + * M666 XYZ endstop_adj (x3) + * M665 R delta_radius + * M665 L delta_diagonal_rod + * M665 S delta_segments_per_second * * ULTIPANEL: - * plaPreheatHotendTemp - * plaPreheatHPBTemp - * plaPreheatFanSpeed - * absPreheatHotendTemp - * absPreheatHPBTemp - * absPreheatFanSpeed + * M145 S0 H plaPreheatHotendTemp + * M145 S0 B plaPreheatHPBTemp + * M145 S0 F plaPreheatFanSpeed + * M145 S1 H absPreheatHotendTemp + * M145 S1 B absPreheatHPBTemp + * M145 S1 F absPreheatFanSpeed * * PIDTEMP: - * Kp[0], Ki[0], Kd[0], Kc[0] - * Kp[1], Ki[1], Kd[1], Kc[1] - * Kp[2], Ki[2], Kd[2], Kc[2] - * Kp[3], Ki[3], Kd[3], Kc[3] + * M301 E0 PIDC Kp[0], Ki[0], Kd[0], Kc[0] + * M301 E1 PIDC Kp[1], Ki[1], Kd[1], Kc[1] + * M301 E2 PIDC Kp[2], Ki[2], Kd[2], Kc[2] + * M301 E3 PIDC Kp[3], Ki[3], Kd[3], Kc[3] * * PIDTEMPBED: - * bedKp, bedKi, bedKd + * M304 PID bedKp, bedKi, bedKd * * DOGLCD: - * lcd_contrast + * M250 C lcd_contrast * * SCARA: - * axis_scaling (x3) + * M365 XYZ axis_scaling (x3) * * FWRETRACT: - * autoretract_enabled - * retract_length - * retract_length_swap - * retract_feedrate - * retract_zlift - * retract_recover_length - * retract_recover_length_swap - * retract_recover_feedrate + * M209 S autoretract_enabled + * M207 S retract_length + * M207 W retract_length_swap + * M207 F retract_feedrate + * M207 Z retract_zlift + * M208 S retract_recover_length + * M208 W retract_recover_length_swap + * M208 F retract_recover_feedrate * - * volumetric_enabled + * M200 D volumetric_enabled (D>0 makes this enabled) * - * filament_size (x4) + * M200 T D filament_size (x4) (T0..3) * - * Z_DUAL_ENDSTOPS - * z_endstop_adj + * Z_DUAL_ENDSTOPS: + * M666 Z z_endstop_adj * */ #include "Marlin.h" @@ -122,7 +122,9 @@ void _EEPROM_readData(int &pos, uint8_t* value, uint8_t size) { #define EEPROM_WRITE_VAR(pos, value) _EEPROM_writeData(pos, (uint8_t*)&value, sizeof(value)) #define EEPROM_READ_VAR(pos, value) _EEPROM_readData(pos, (uint8_t*)&value, sizeof(value)) -//====================================================================================== +/** + * Store Configuration Settings - M500 + */ #define DUMMY_PID_VALUE 3000.0f @@ -235,7 +237,7 @@ void Config_StoreSettings() { EEPROM_WRITE_VAR(i, bedKi); EEPROM_WRITE_VAR(i, bedKd); - #ifndef DOGLCD + #ifndef HAS_LCD_CONTRAST int lcd_contrast = 32; #endif EEPROM_WRITE_VAR(i, lcd_contrast); @@ -286,6 +288,10 @@ void Config_StoreSettings() { SERIAL_ECHOLNPGM(" bytes)"); } +/** + * Retrieve Configuration Settings - M501 + */ + void Config_RetrieveSettings() { int i = EEPROM_OFFSET; @@ -412,7 +418,7 @@ void Config_RetrieveSettings() { for (int q=2; q--;) EEPROM_READ_VAR(i, dummy); // bedKi, bedKd } - #ifndef DOGLCD + #ifndef HAS_LCD_CONTRAST int lcd_contrast; #endif EEPROM_READ_VAR(i, lcd_contrast); @@ -467,6 +473,10 @@ void Config_RetrieveSettings() { #endif // EEPROM_SETTINGS +/** + * Reset Configuration Settings - M502 + */ + void Config_ResetDefault() { float tmp1[] = DEFAULT_AXIS_STEPS_PER_UNIT; float tmp2[] = DEFAULT_MAX_FEEDRATE; @@ -522,7 +532,7 @@ void Config_ResetDefault() { absPreheatFanSpeed = ABS_PREHEAT_FAN_SPEED; #endif - #ifdef DOGLCD + #ifdef HAS_LCD_CONTRAST lcd_contrast = DEFAULT_LCD_CONTRAST; #endif @@ -584,14 +594,20 @@ void Config_ResetDefault() { #ifndef DISABLE_M503 +/** + * Print Configuration Settings - M503 + */ + +#define CONFIG_ECHO_START do{ if (!forReplay) SERIAL_ECHO_START; }while(0) + void Config_PrintSettings(bool forReplay) { // Always have this function, even with EEPROM_SETTINGS disabled, the current values will be shown - SERIAL_ECHO_START; + CONFIG_ECHO_START; if (!forReplay) { SERIAL_ECHOLNPGM("Steps per unit:"); - SERIAL_ECHO_START; + CONFIG_ECHO_START; } SERIAL_ECHOPAIR(" M92 X", axis_steps_per_unit[X_AXIS]); SERIAL_ECHOPAIR(" Y", axis_steps_per_unit[Y_AXIS]); @@ -599,23 +615,23 @@ void Config_PrintSettings(bool forReplay) { SERIAL_ECHOPAIR(" E", axis_steps_per_unit[E_AXIS]); SERIAL_EOL; - SERIAL_ECHO_START; + CONFIG_ECHO_START; #ifdef SCARA if (!forReplay) { SERIAL_ECHOLNPGM("Scaling factors:"); - SERIAL_ECHO_START; + CONFIG_ECHO_START; } SERIAL_ECHOPAIR(" M365 X", axis_scaling[X_AXIS]); SERIAL_ECHOPAIR(" Y", axis_scaling[Y_AXIS]); SERIAL_ECHOPAIR(" Z", axis_scaling[Z_AXIS]); SERIAL_EOL; - SERIAL_ECHO_START; + CONFIG_ECHO_START; #endif // SCARA if (!forReplay) { SERIAL_ECHOLNPGM("Maximum feedrates (mm/s):"); - SERIAL_ECHO_START; + CONFIG_ECHO_START; } SERIAL_ECHOPAIR(" M203 X", max_feedrate[X_AXIS]); SERIAL_ECHOPAIR(" Y", max_feedrate[Y_AXIS]); @@ -623,160 +639,224 @@ void Config_PrintSettings(bool forReplay) { SERIAL_ECHOPAIR(" E", max_feedrate[E_AXIS]); SERIAL_EOL; - SERIAL_ECHO_START; + CONFIG_ECHO_START; if (!forReplay) { SERIAL_ECHOLNPGM("Maximum Acceleration (mm/s2):"); - SERIAL_ECHO_START; + CONFIG_ECHO_START; } - SERIAL_ECHOPAIR(" M201 X", max_acceleration_units_per_sq_second[X_AXIS] ); - SERIAL_ECHOPAIR(" Y", max_acceleration_units_per_sq_second[Y_AXIS] ); - SERIAL_ECHOPAIR(" Z", max_acceleration_units_per_sq_second[Z_AXIS] ); + SERIAL_ECHOPAIR(" M201 X", max_acceleration_units_per_sq_second[X_AXIS]); + SERIAL_ECHOPAIR(" Y", max_acceleration_units_per_sq_second[Y_AXIS]); + SERIAL_ECHOPAIR(" Z", max_acceleration_units_per_sq_second[Z_AXIS]); SERIAL_ECHOPAIR(" E", max_acceleration_units_per_sq_second[E_AXIS]); SERIAL_EOL; - SERIAL_ECHO_START; + CONFIG_ECHO_START; if (!forReplay) { SERIAL_ECHOLNPGM("Accelerations: P=printing, R=retract and T=travel"); - SERIAL_ECHO_START; + CONFIG_ECHO_START; } - SERIAL_ECHOPAIR(" M204 P", acceleration ); + SERIAL_ECHOPAIR(" M204 P", acceleration); SERIAL_ECHOPAIR(" R", retract_acceleration); SERIAL_ECHOPAIR(" T", travel_acceleration); SERIAL_EOL; - SERIAL_ECHO_START; + CONFIG_ECHO_START; if (!forReplay) { SERIAL_ECHOLNPGM("Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)"); - SERIAL_ECHO_START; + CONFIG_ECHO_START; } - SERIAL_ECHOPAIR(" M205 S", minimumfeedrate ); - SERIAL_ECHOPAIR(" T", mintravelfeedrate ); - SERIAL_ECHOPAIR(" B", minsegmenttime ); - SERIAL_ECHOPAIR(" X", max_xy_jerk ); + SERIAL_ECHOPAIR(" M205 S", minimumfeedrate); + SERIAL_ECHOPAIR(" T", mintravelfeedrate); + SERIAL_ECHOPAIR(" B", minsegmenttime); + SERIAL_ECHOPAIR(" X", max_xy_jerk); SERIAL_ECHOPAIR(" Z", max_z_jerk); SERIAL_ECHOPAIR(" E", max_e_jerk); SERIAL_EOL; - SERIAL_ECHO_START; + CONFIG_ECHO_START; if (!forReplay) { SERIAL_ECHOLNPGM("Home offset (mm):"); - SERIAL_ECHO_START; + CONFIG_ECHO_START; } - SERIAL_ECHOPAIR(" M206 X", home_offset[X_AXIS] ); - SERIAL_ECHOPAIR(" Y", home_offset[Y_AXIS] ); - SERIAL_ECHOPAIR(" Z", home_offset[Z_AXIS] ); + SERIAL_ECHOPAIR(" M206 X", home_offset[X_AXIS]); + SERIAL_ECHOPAIR(" Y", home_offset[Y_AXIS]); + SERIAL_ECHOPAIR(" Z", home_offset[Z_AXIS]); SERIAL_EOL; + #ifdef MESH_BED_LEVELING + if (!forReplay) { + SERIAL_ECHOLNPGM("Mesh bed leveling:"); + CONFIG_ECHO_START; + } + SERIAL_ECHOPAIR(" M420 S", (int32_t)mbl.active); + SERIAL_ECHOPAIR(" X", MESH_NUM_X_POINTS); + SERIAL_ECHOPAIR(" Y", MESH_NUM_Y_POINTS); + SERIAL_EOL; + for (int y=0; y 1 + if (forReplay) { + for (uint8_t i = 0; i < EXTRUDERS; i++) { + CONFIG_ECHO_START; + SERIAL_ECHOPAIR(" M301 E", (unsigned long)i); + SERIAL_ECHOPAIR(" P", PID_PARAM(Kp, i)); + SERIAL_ECHOPAIR(" I", unscalePID_i(PID_PARAM(Ki, i))); + SERIAL_ECHOPAIR(" D", unscalePID_d(PID_PARAM(Kd, i))); + #ifdef PID_ADD_EXTRUSION_RATE + SERIAL_ECHOPAIR(" C", PID_PARAM(Kc, i)); + #endif + SERIAL_EOL; + } + } + else + #endif // EXTRUDERS > 1 + // !forReplay || EXTRUDERS == 1 + { + CONFIG_ECHO_START; + SERIAL_ECHOPAIR(" M301 P", PID_PARAM(Kp, 0)); // for compatibility with hosts, only echo values for E0 + SERIAL_ECHOPAIR(" I", unscalePID_i(PID_PARAM(Ki, 0))); + SERIAL_ECHOPAIR(" D", unscalePID_d(PID_PARAM(Kd, 0))); + #ifdef PID_ADD_EXTRUSION_RATE + SERIAL_ECHOPAIR(" C", PID_PARAM(Kc, 0)); + #endif + SERIAL_EOL; + } + #endif // PIDTEMP + #ifdef PIDTEMPBED - SERIAL_ECHOPAIR(" M304 P", bedKp); // for compatibility with hosts, only echos values for E0 + CONFIG_ECHO_START; + SERIAL_ECHOPAIR(" M304 P", bedKp); SERIAL_ECHOPAIR(" I", unscalePID_i(bedKi)); SERIAL_ECHOPAIR(" D", unscalePID_d(bedKd)); SERIAL_EOL; #endif + + #endif // PIDTEMP || PIDTEMPBED + + #ifdef HAS_LCD_CONTRAST + CONFIG_ECHO_START; + if (!forReplay) { + SERIAL_ECHOLNPGM("LCD Contrast:"); + CONFIG_ECHO_START; + } + SERIAL_ECHOPAIR(" M250 C", (unsigned long)lcd_contrast); + SERIAL_EOL; #endif #ifdef FWRETRACT - SERIAL_ECHO_START; + CONFIG_ECHO_START; if (!forReplay) { SERIAL_ECHOLNPGM("Retract: S=Length (mm) F:Speed (mm/m) Z: ZLift (mm)"); - SERIAL_ECHO_START; + CONFIG_ECHO_START; } SERIAL_ECHOPAIR(" M207 S", retract_length); + #if EXTRUDERS > 1 + SERIAL_ECHOPAIR(" W", retract_length_swap); + #endif SERIAL_ECHOPAIR(" F", retract_feedrate*60); SERIAL_ECHOPAIR(" Z", retract_zlift); SERIAL_EOL; - SERIAL_ECHO_START; + CONFIG_ECHO_START; if (!forReplay) { SERIAL_ECHOLNPGM("Recover: S=Extra length (mm) F:Speed (mm/m)"); - SERIAL_ECHO_START; + CONFIG_ECHO_START; } SERIAL_ECHOPAIR(" M208 S", retract_recover_length); + #if EXTRUDERS > 1 + SERIAL_ECHOPAIR(" W", retract_recover_length_swap); + #endif SERIAL_ECHOPAIR(" F", retract_recover_feedrate*60); SERIAL_EOL; - SERIAL_ECHO_START; + CONFIG_ECHO_START; if (!forReplay) { SERIAL_ECHOLNPGM("Auto-Retract: S=0 to disable, 1 to interpret extrude-only moves as retracts or recoveries"); - SERIAL_ECHO_START; + CONFIG_ECHO_START; } SERIAL_ECHOPAIR(" M209 S", (unsigned long)(autoretract_enabled ? 1 : 0)); SERIAL_EOL; - #if EXTRUDERS > 1 - if (!forReplay) { - SERIAL_ECHO_START; - SERIAL_ECHOLNPGM("Multi-extruder settings:"); - SERIAL_ECHO_START; - SERIAL_ECHOPAIR(" Swap retract length (mm): ", retract_length_swap); - SERIAL_EOL; - SERIAL_ECHO_START; - SERIAL_ECHOPAIR(" Swap rec. addl. length (mm): ", retract_recover_length_swap); - SERIAL_EOL; - } - #endif // EXTRUDERS > 1 - #endif // FWRETRACT - SERIAL_ECHO_START; if (volumetric_enabled) { if (!forReplay) { + CONFIG_ECHO_START; SERIAL_ECHOLNPGM("Filament settings:"); - SERIAL_ECHO_START; } + + CONFIG_ECHO_START; SERIAL_ECHOPAIR(" M200 D", filament_size[0]); SERIAL_EOL; #if EXTRUDERS > 1 - SERIAL_ECHO_START; + CONFIG_ECHO_START; SERIAL_ECHOPAIR(" M200 T1 D", filament_size[1]); SERIAL_EOL; #if EXTRUDERS > 2 - SERIAL_ECHO_START; + CONFIG_ECHO_START; SERIAL_ECHOPAIR(" M200 T2 D", filament_size[2]); SERIAL_EOL; #if EXTRUDERS > 3 - SERIAL_ECHO_START; + CONFIG_ECHO_START; SERIAL_ECHOPAIR(" M200 T3 D", filament_size[3]); SERIAL_EOL; #endif @@ -785,21 +865,23 @@ void Config_PrintSettings(bool forReplay) { } else { if (!forReplay) { + CONFIG_ECHO_START; SERIAL_ECHOLNPGM("Filament settings: Disabled"); } } #ifdef ENABLE_AUTO_BED_LEVELING - SERIAL_ECHO_START; #ifdef CUSTOM_M_CODES if (!forReplay) { + CONFIG_ECHO_START; SERIAL_ECHOLNPGM("Z-Probe Offset (mm):"); - SERIAL_ECHO_START; } + CONFIG_ECHO_START; SERIAL_ECHOPAIR(" M", (unsigned long)CUSTOM_M_CODE_SET_Z_PROBE_OFFSET); SERIAL_ECHOPAIR(" Z", -zprobe_zoffset); #else if (!forReplay) { + CONFIG_ECHO_START; SERIAL_ECHOPAIR("Z-Probe Offset (mm):", -zprobe_zoffset); } #endif diff --git a/Marlin/configurator/config/Configuration_adv.h b/Marlin/configurator/config/Configuration_adv.h index 6478eb923..059f0c5c1 100644 --- a/Marlin/configurator/config/Configuration_adv.h +++ b/Marlin/configurator/config/Configuration_adv.h @@ -355,7 +355,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HEATERS_PARALLEL //=========================================================================== -//=============================Buffers ============================ +//================================= Buffers ================================= //=========================================================================== // @section hidden diff --git a/Marlin/configurator/config/language.h b/Marlin/configurator/config/language.h index 2576bec42..b6beb4747 100644 --- a/Marlin/configurator/config/language.h +++ b/Marlin/configurator/config/language.h @@ -70,7 +70,7 @@ #endif #else #ifndef MACHINE_NAME - #define MACHINE_NAME "Mendel" + #define MACHINE_NAME "3D Printer" #endif #endif @@ -158,6 +158,9 @@ #define MSG_Z_MAX "z_max: " #define MSG_Z2_MAX "z2_max: " #define MSG_Z_PROBE "z_probe: " +#define MSG_ERR_MATERIAL_INDEX "M145 S out of range (0-1)" +#define MSG_ERR_XYZ_REQUIRED_FOR_M421 "M421 requires XYZ parameters" +#define MSG_ERR_MESH_INDEX_OOB "Mesh XY index is out of bounds" #define MSG_M119_REPORT "Reporting endstop status" #define MSG_ENDSTOP_HIT "TRIGGERED" #define MSG_ENDSTOP_OPEN "open" diff --git a/Marlin/example_configurations/Felix/Configuration_adv.h b/Marlin/example_configurations/Felix/Configuration_adv.h index a80790b95..bc27cd8dc 100644 --- a/Marlin/example_configurations/Felix/Configuration_adv.h +++ b/Marlin/example_configurations/Felix/Configuration_adv.h @@ -355,7 +355,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HEATERS_PARALLEL //=========================================================================== -//=============================Buffers ============================ +//================================= Buffers ================================= //=========================================================================== // @section hidden diff --git a/Marlin/example_configurations/Hephestos/Configuration_adv.h b/Marlin/example_configurations/Hephestos/Configuration_adv.h index 84536d044..39545c378 100644 --- a/Marlin/example_configurations/Hephestos/Configuration_adv.h +++ b/Marlin/example_configurations/Hephestos/Configuration_adv.h @@ -355,7 +355,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HEATERS_PARALLEL //=========================================================================== -//=============================Buffers ============================ +//================================= Buffers ================================= //=========================================================================== // @section hidden diff --git a/Marlin/example_configurations/K8200/Configuration_adv.h b/Marlin/example_configurations/K8200/Configuration_adv.h index a80790b95..bc27cd8dc 100644 --- a/Marlin/example_configurations/K8200/Configuration_adv.h +++ b/Marlin/example_configurations/K8200/Configuration_adv.h @@ -355,7 +355,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HEATERS_PARALLEL //=========================================================================== -//=============================Buffers ============================ +//================================= Buffers ================================= //=========================================================================== // @section hidden diff --git a/Marlin/example_configurations/SCARA/Configuration_adv.h b/Marlin/example_configurations/SCARA/Configuration_adv.h index edc2445af..bdf2eab4b 100644 --- a/Marlin/example_configurations/SCARA/Configuration_adv.h +++ b/Marlin/example_configurations/SCARA/Configuration_adv.h @@ -355,7 +355,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HEATERS_PARALLEL //=========================================================================== -//=============================Buffers ============================ +//================================= Buffers ================================= //=========================================================================== // @section hidden diff --git a/Marlin/example_configurations/WITBOX/Configuration_adv.h b/Marlin/example_configurations/WITBOX/Configuration_adv.h index 15c523284..e9c0cd0f1 100644 --- a/Marlin/example_configurations/WITBOX/Configuration_adv.h +++ b/Marlin/example_configurations/WITBOX/Configuration_adv.h @@ -355,7 +355,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HEATERS_PARALLEL //=========================================================================== -//=============================Buffers ============================ +//================================= Buffers ================================= //=========================================================================== // @section hidden diff --git a/Marlin/example_configurations/delta/generic/Configuration_adv.h b/Marlin/example_configurations/delta/generic/Configuration_adv.h index 88b76c66e..aebfa59d5 100644 --- a/Marlin/example_configurations/delta/generic/Configuration_adv.h +++ b/Marlin/example_configurations/delta/generic/Configuration_adv.h @@ -356,7 +356,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HEATERS_PARALLEL //=========================================================================== -//=============================Buffers ============================ +//================================= Buffers ================================= //=========================================================================== // @section hidden diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h index 9b52ede7b..5e8337ce8 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h @@ -355,7 +355,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HEATERS_PARALLEL //=========================================================================== -//=============================Buffers ============================ +//================================= Buffers ================================= //=========================================================================== // @section hidden diff --git a/Marlin/example_configurations/makibox/Configuration_adv.h b/Marlin/example_configurations/makibox/Configuration_adv.h index 7b63732a6..2d97c626b 100644 --- a/Marlin/example_configurations/makibox/Configuration_adv.h +++ b/Marlin/example_configurations/makibox/Configuration_adv.h @@ -355,7 +355,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HEATERS_PARALLEL //=========================================================================== -//=============================Buffers ============================ +//================================= Buffers ================================= //=========================================================================== // @section hidden diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h index d221f080b..832fb8355 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h @@ -355,7 +355,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define HEATERS_PARALLEL //=========================================================================== -//=============================Buffers ============================ +//================================= Buffers ================================= //=========================================================================== // @section hidden diff --git a/Marlin/language.h b/Marlin/language.h index c9ddfeee4..b6beb4747 100644 --- a/Marlin/language.h +++ b/Marlin/language.h @@ -158,6 +158,9 @@ #define MSG_Z_MAX "z_max: " #define MSG_Z2_MAX "z2_max: " #define MSG_Z_PROBE "z_probe: " +#define MSG_ERR_MATERIAL_INDEX "M145 S out of range (0-1)" +#define MSG_ERR_XYZ_REQUIRED_FOR_M421 "M421 requires XYZ parameters" +#define MSG_ERR_MESH_INDEX_OOB "Mesh XY index is out of bounds" #define MSG_M119_REPORT "Reporting endstop status" #define MSG_ENDSTOP_HIT "TRIGGERED" #define MSG_ENDSTOP_OPEN "open" diff --git a/Marlin/planner.cpp b/Marlin/planner.cpp index 060be3007..a8558d6c4 100644 --- a/Marlin/planner.cpp +++ b/Marlin/planner.cpp @@ -1,54 +1,51 @@ -/* - planner.c - buffers movement commands and manages the acceleration profile plan - Part of Grbl - - Copyright (c) 2009-2011 Simen Svale Skogsrud - - Grbl is free software: you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation, either version 3 of the License, or - (at your option) any later version. - - Grbl is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with Grbl. If not, see . - */ - -/* The ring buffer implementation gleaned from the wiring_serial library by David A. Mellis. */ - -/* - Reasoning behind the mathematics in this module (in the key of 'Mathematica'): - - s == speed, a == acceleration, t == time, d == distance - - Basic definitions: - - Speed[s_, a_, t_] := s + (a*t) - Travel[s_, a_, t_] := Integrate[Speed[s, a, t], t] - - Distance to reach a specific speed with a constant acceleration: - - Solve[{Speed[s, a, t] == m, Travel[s, a, t] == d}, d, t] - d -> (m^2 - s^2)/(2 a) --> estimate_acceleration_distance() - - Speed after a given distance of travel with constant acceleration: - - Solve[{Speed[s, a, t] == m, Travel[s, a, t] == d}, m, t] - m -> Sqrt[2 a d + s^2] - - DestinationSpeed[s_, a_, d_] := Sqrt[2 a d + s^2] - - When to start braking (di) to reach a specified destionation speed (s2) after accelerating - from initial speed s1 without ever stopping at a plateau: - - Solve[{DestinationSpeed[s1, a, di] == DestinationSpeed[s2, a, d - di]}, di] - di -> (2 a d - s1^2 + s2^2)/(4 a) --> intersection_distance() - - IntersectionDistance[s1_, s2_, a_, d_] := (2 a d - s1^2 + s2^2)/(4 a) +/** + * planner.cpp - Buffer movement commands and manage the acceleration profile plan + * Part of Grbl + * + * Copyright (c) 2009-2011 Simen Svale Skogsrud + * + * Grbl is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * Grbl is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with Grbl. If not, see . + * + * + * The ring buffer implementation gleaned from the wiring_serial library by David A. Mellis. + * + * + * Reasoning behind the mathematics in this module (in the key of 'Mathematica'): + * + * s == speed, a == acceleration, t == time, d == distance + * + * Basic definitions: + * Speed[s_, a_, t_] := s + (a*t) + * Travel[s_, a_, t_] := Integrate[Speed[s, a, t], t] + * + * Distance to reach a specific speed with a constant acceleration: + * Solve[{Speed[s, a, t] == m, Travel[s, a, t] == d}, d, t] + * d -> (m^2 - s^2)/(2 a) --> estimate_acceleration_distance() + * + * Speed after a given distance of travel with constant acceleration: + * Solve[{Speed[s, a, t] == m, Travel[s, a, t] == d}, m, t] + * m -> Sqrt[2 a d + s^2] + * + * DestinationSpeed[s_, a_, d_] := Sqrt[2 a d + s^2] + * + * When to start braking (di) to reach a specified destination speed (s2) after accelerating + * from initial speed s1 without ever stopping at a plateau: + * Solve[{DestinationSpeed[s1, a, di] == DestinationSpeed[s2, a, d - di]}, di] + * di -> (2 a d - s1^2 + s2^2)/(4 a) --> intersection_distance() + * + * IntersectionDistance[s1_, s2_, a_, d_] := (2 a d - s1^2 + s2^2)/(4 a) + * */ #include "Marlin.h" @@ -71,17 +68,17 @@ float max_feedrate[NUM_AXIS]; // Max speeds in mm per minute float axis_steps_per_unit[NUM_AXIS]; unsigned long max_acceleration_units_per_sq_second[NUM_AXIS]; // Use M201 to override by software float minimumfeedrate; -float acceleration; // Normal acceleration mm/s^2 THIS IS THE DEFAULT ACCELERATION for all printing moves. M204 SXXXX -float retract_acceleration; // mm/s^2 filament pull-pack and push-forward while standing still in the other axis M204 TXXXX -float travel_acceleration; // Travel acceleration mm/s^2 THIS IS THE DEFAULT ACCELERATION for all NON printing moves. M204 MXXXX -float max_xy_jerk; //speed than can be stopped at once, if i understand correctly. +float acceleration; // Normal acceleration mm/s^2 DEFAULT ACCELERATION for all printing moves. M204 SXXXX +float retract_acceleration; // Retract acceleration mm/s^2 filament pull-back and push-forward while standing still in the other axes M204 TXXXX +float travel_acceleration; // Travel acceleration mm/s^2 DEFAULT ACCELERATION for all NON printing moves. M204 MXXXX +float max_xy_jerk; // The largest speed change requiring no acceleration float max_z_jerk; float max_e_jerk; float mintravelfeedrate; unsigned long axis_steps_per_sqr_second[NUM_AXIS]; #ifdef ENABLE_AUTO_BED_LEVELING - // this holds the required transform to compensate for bed level + // Transform required to compensate for bed level matrix_3x3 plan_bed_level_matrix = { 1.0, 0.0, 0.0, 0.0, 1.0, 0.0, @@ -89,11 +86,6 @@ unsigned long axis_steps_per_sqr_second[NUM_AXIS]; }; #endif // ENABLE_AUTO_BED_LEVELING -// The current position of the tool in absolute steps -long position[NUM_AXIS]; //rescaled from extern when axis_steps_per_unit are changed by gcode -static float previous_speed[NUM_AXIS]; // Speed of previous path line segment -static float previous_nominal_speed; // Nominal speed of previous path line segment - #ifdef AUTOTEMP float autotemp_max = 250; float autotemp_min = 210; @@ -101,18 +93,25 @@ static float previous_nominal_speed; // Nominal speed of previous path line segm bool autotemp_enabled = false; #endif -unsigned char g_uc_extruder_last_move[4] = {0,0,0,0}; - //=========================================================================== -//=================semi-private variables, used in inline functions ===== +//============ semi-private variables, used in inline functions ============= //=========================================================================== + block_t block_buffer[BLOCK_BUFFER_SIZE]; // A ring buffer for motion instfructions volatile unsigned char block_buffer_head; // Index of the next block to be pushed volatile unsigned char block_buffer_tail; // Index of the block to process now //=========================================================================== -//=============================private variables ============================ +//============================ private variables ============================ //=========================================================================== + +// The current position of the tool in absolute steps +long position[NUM_AXIS]; // Rescaled from extern when axis_steps_per_unit are changed by gcode +static float previous_speed[NUM_AXIS]; // Speed of previous path line segment +static float previous_nominal_speed; // Nominal speed of previous path line segment + +unsigned char g_uc_extruder_last_move[4] = {0,0,0,0}; + #ifdef XY_FREQUENCY_LIMIT // Used for the frequency limit #define MAX_FREQ_TIME (1000000.0/XY_FREQUENCY_LIMIT) @@ -126,15 +125,15 @@ volatile unsigned char block_buffer_tail; // Index of the block to pro static char meas_sample; //temporary variable to hold filament measurement sample #endif +//=========================================================================== +//================================ functions ================================ +//=========================================================================== + // Get the next / previous index of the next block in the ring buffer // NOTE: Using & here (not %) because BLOCK_BUFFER_SIZE is always a power of 2 FORCE_INLINE int8_t next_block_index(int8_t block_index) { return BLOCK_MOD(block_index + 1); } FORCE_INLINE int8_t prev_block_index(int8_t block_index) { return BLOCK_MOD(block_index - 1); } -//=========================================================================== -//================================ Functions ================================ -//=========================================================================== - // Calculates the distance (not time) it takes to accelerate from initial_rate to target_rate using the // given acceleration: FORCE_INLINE float estimate_acceleration_distance(float initial_rate, float target_rate, float acceleration) { diff --git a/Marlin/planner.h b/Marlin/planner.h index d96aa8c11..c54ed4411 100644 --- a/Marlin/planner.h +++ b/Marlin/planner.h @@ -115,15 +115,19 @@ FORCE_INLINE uint8_t movesplanned() { return BLOCK_MOD(block_buffer_head - block void plan_set_e_position(const float &e); +//=========================================================================== +//============================= public variables ============================ +//=========================================================================== + extern millis_t minsegmenttime; -extern float max_feedrate[NUM_AXIS]; // set the max speeds +extern float max_feedrate[NUM_AXIS]; // Max speeds in mm per minute extern float axis_steps_per_unit[NUM_AXIS]; extern unsigned long max_acceleration_units_per_sq_second[NUM_AXIS]; // Use M201 to override by software extern float minimumfeedrate; -extern float acceleration; // Normal acceleration mm/s^2 THIS IS THE DEFAULT ACCELERATION for all moves. M204 SXXXX -extern float retract_acceleration; // mm/s^2 filament pull-pack and push-forward while standing still in the other axis M204 TXXXX -extern float travel_acceleration; // Travel acceleration mm/s^2 THIS IS THE DEFAULT ACCELERATION for all NON printing moves. M204 MXXXX -extern float max_xy_jerk; //speed than can be stopped at once, if i understand correctly. +extern float acceleration; // Normal acceleration mm/s^2 DEFAULT ACCELERATION for all printing moves. M204 SXXXX +extern float retract_acceleration; // Retract acceleration mm/s^2 filament pull-back and push-forward while standing still in the other axes M204 TXXXX +extern float travel_acceleration; // Travel acceleration mm/s^2 DEFAULT ACCELERATION for all NON printing moves. M204 MXXXX +extern float max_xy_jerk; // The largest speed change requiring no acceleration extern float max_z_jerk; extern float max_e_jerk; extern float mintravelfeedrate; diff --git a/Marlin/temperature.cpp b/Marlin/temperature.cpp index fa17b6c4c..a494e3a9d 100644 --- a/Marlin/temperature.cpp +++ b/Marlin/temperature.cpp @@ -89,8 +89,9 @@ unsigned char soft_pwm_bed; #endif //=========================================================================== -//=============================private variables============================ +//============================ private variables ============================ //=========================================================================== + static volatile bool temp_meas_ready = false; #ifdef PIDTEMP @@ -187,7 +188,7 @@ static void updateTemperaturesFromRawValues(); #endif //=========================================================================== -//============================= functions ============================ +//================================ functions ================================ //=========================================================================== void PID_autotune(float temp, int extruder, int ncycles) diff --git a/Marlin/ultralcd.cpp b/Marlin/ultralcd.cpp index 81844573e..3895dc551 100644 --- a/Marlin/ultralcd.cpp +++ b/Marlin/ultralcd.cpp @@ -868,10 +868,10 @@ static void lcd_control_temperature_preheat_pla_settings_menu() { MENU_ITEM(back, MSG_TEMPERATURE, lcd_control_temperature_menu); MENU_ITEM_EDIT(int3, MSG_FAN_SPEED, &plaPreheatFanSpeed, 0, 255); #if TEMP_SENSOR_0 != 0 - MENU_ITEM_EDIT(int3, MSG_NOZZLE, &plaPreheatHotendTemp, 0, HEATER_0_MAXTEMP - 15); + MENU_ITEM_EDIT(int3, MSG_NOZZLE, &plaPreheatHotendTemp, HEATER_0_MINTEMP, HEATER_0_MAXTEMP - 15); #endif #if TEMP_SENSOR_BED != 0 - MENU_ITEM_EDIT(int3, MSG_BED, &plaPreheatHPBTemp, 0, BED_MAXTEMP - 15); + MENU_ITEM_EDIT(int3, MSG_BED, &plaPreheatHPBTemp, BED_MINTEMP, BED_MAXTEMP - 15); #endif #ifdef EEPROM_SETTINGS MENU_ITEM(function, MSG_STORE_EPROM, Config_StoreSettings); @@ -884,10 +884,10 @@ static void lcd_control_temperature_preheat_abs_settings_menu() { MENU_ITEM(back, MSG_TEMPERATURE, lcd_control_temperature_menu); MENU_ITEM_EDIT(int3, MSG_FAN_SPEED, &absPreheatFanSpeed, 0, 255); #if TEMP_SENSOR_0 != 0 - MENU_ITEM_EDIT(int3, MSG_NOZZLE, &absPreheatHotendTemp, 0, HEATER_0_MAXTEMP - 15); + MENU_ITEM_EDIT(int3, MSG_NOZZLE, &absPreheatHotendTemp, HEATER_0_MINTEMP, HEATER_0_MAXTEMP - 15); #endif #if TEMP_SENSOR_BED != 0 - MENU_ITEM_EDIT(int3, MSG_BED, &absPreheatHPBTemp, 0, BED_MAXTEMP - 15); + MENU_ITEM_EDIT(int3, MSG_BED, &absPreheatHPBTemp, BED_MINTEMP, BED_MAXTEMP - 15); #endif #ifdef EEPROM_SETTINGS MENU_ITEM(function, MSG_STORE_EPROM, Config_StoreSettings); diff --git a/Marlin/watchdog.cpp b/Marlin/watchdog.cpp index b378ca706..8505f7efa 100644 --- a/Marlin/watchdog.cpp +++ b/Marlin/watchdog.cpp @@ -7,11 +7,11 @@ #include "ultralcd.h" //=========================================================================== -//=============================private variables ============================ +//============================ private variables ============================ //=========================================================================== //=========================================================================== -//=============================functinos ============================ +//================================ functions ================================ //=========================================================================== @@ -36,7 +36,7 @@ void watchdog_reset() } //=========================================================================== -//=============================ISR ============================ +//=================================== ISR =================================== //=========================================================================== //Watchdog timer interrupt, called if main program blocks >1sec and manual reset is enabled.