diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp
index fd49ab6fa..f9707daf1 100644
--- a/Marlin/Marlin_main.cpp
+++ b/Marlin/Marlin_main.cpp
@@ -3084,7 +3084,7 @@ inline void gcode_G28() {
           #if ENABLED(DELTA)
             // Avoid probing the corners (outside the round or hexagon print surface) on a delta printer.
             float distance_from_center = sqrt(xProbe * xProbe + yProbe * yProbe);
-            if (distance_from_center > DELTA_PROBABLE_RADIUS) continue;
+            if (distance_from_center > DELTA_PROBEABLE_RADIUS) continue;
           #endif //DELTA
 
           ProbeAction act;
diff --git a/Marlin/SanityCheck.h b/Marlin/SanityCheck.h
index 3e1c52ca0..5204fce59 100644
--- a/Marlin/SanityCheck.h
+++ b/Marlin/SanityCheck.h
@@ -220,7 +220,7 @@
    * Check if Probe_Offset * Grid Points is greater than Probing Range
    */
   #if ENABLED(AUTO_BED_LEVELING_GRID)
-    #ifndef DELTA_PROBABLE_RADIUS
+    #ifndef DELTA_PROBEABLE_RADIUS
       // Be sure points are in the right order
       #if LEFT_PROBE_BED_POSITION > RIGHT_PROBE_BED_POSITION
         #error LEFT_PROBE_BED_POSITION must be less than RIGHT_PROBE_BED_POSITION.
diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration.h b/Marlin/example_configurations/delta/biv2.5/Configuration.h
index 9b044ee1c..2f339cbfa 100644
--- a/Marlin/example_configurations/delta/biv2.5/Configuration.h
+++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h
@@ -567,11 +567,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
   #if ENABLED(AUTO_BED_LEVELING_GRID)
 
     // Set the rectangle in which to probe.
-    #define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
-    #define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
-    #define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
-    #define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
-    #define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
+    #define DELTA_PROBEABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
+    #define LEFT_PROBE_BED_POSITION -DELTA_PROBEABLE_RADIUS
+    #define RIGHT_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
+    #define FRONT_PROBE_BED_POSITION -DELTA_PROBEABLE_RADIUS
+    #define BACK_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
 
     #define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
 
diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h
index e3e4e6e41..687f9b0b0 100644
--- a/Marlin/example_configurations/delta/generic/Configuration.h
+++ b/Marlin/example_configurations/delta/generic/Configuration.h
@@ -567,11 +567,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
   #if ENABLED(AUTO_BED_LEVELING_GRID)
 
     // set the rectangle in which to probe
-    #define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
-    #define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
-    #define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
-    #define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
-    #define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
+    #define DELTA_PROBEABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
+    #define LEFT_PROBE_BED_POSITION -DELTA_PROBEABLE_RADIUS
+    #define RIGHT_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
+    #define FRONT_PROBE_BED_POSITION -DELTA_PROBEABLE_RADIUS
+    #define BACK_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
 
     #define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
 
diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
index 1fea261b1..41132655d 100644
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
@@ -567,11 +567,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
   #if ENABLED(AUTO_BED_LEVELING_GRID)
 
     // set the rectangle in which to probe
-    #define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
-    #define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
-    #define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
-    #define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
-    #define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
+    #define DELTA_PROBEABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
+    #define LEFT_PROBE_BED_POSITION -DELTA_PROBEABLE_RADIUS
+    #define RIGHT_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
+    #define FRONT_PROBE_BED_POSITION -DELTA_PROBEABLE_RADIUS
+    #define BACK_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
 
     #define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
 
diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
index 57bb084ca..ea8696163 100644
--- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
@@ -554,11 +554,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
   #if ENABLED(AUTO_BED_LEVELING_GRID)
 
     // set the rectangle in which to probe
-    #define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS-25)
-    #define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
-    #define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
-    #define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
-    #define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
+    #define DELTA_PROBEABLE_RADIUS (DELTA_PRINTABLE_RADIUS-25)
+    #define LEFT_PROBE_BED_POSITION -DELTA_PROBEABLE_RADIUS
+    #define RIGHT_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
+    #define FRONT_PROBE_BED_POSITION -DELTA_PROBEABLE_RADIUS
+    #define BACK_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
 
     #define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
 
diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration.h b/Marlin/example_configurations/delta/kossel_xl/Configuration.h
index 9d94a8840..9a508859a 100644
--- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h
@@ -559,11 +559,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
   #if ENABLED(AUTO_BED_LEVELING_GRID)
 
-    #define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
-    #define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
-    #define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
-    #define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
-    #define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
+    #define DELTA_PROBEABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
+    #define LEFT_PROBE_BED_POSITION -DELTA_PROBEABLE_RADIUS
+    #define RIGHT_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
+    #define FRONT_PROBE_BED_POSITION -DELTA_PROBEABLE_RADIUS
+    #define BACK_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
 
     #define MIN_PROBE_EDGE 20 // The Z probe minimum square sides can be no smaller than this.