Merge pull request #4414 from thinkyhead/rc_split_conditionals
Split up Conditionals.h into two filesmaster
Scott Lahteine
8 years ago
committed by
GitHub
commit
5597400cda
@ -0,0 +1,270 @@
|
||||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* Conditionals_LCD.h
|
||||
* LCD Defines that depend on configuration but are not editable.
|
||||
*/
|
||||
|
||||
#ifndef CONDITIONALS_LCD_H // Get the LCD defines which are needed first
|
||||
#define CONDITIONALS_LCD_H
|
||||
|
||||
#define LCD_HAS_DIRECTIONAL_BUTTONS (BUTTON_EXISTS(UP) || BUTTON_EXISTS(DWN) || BUTTON_EXISTS(LFT) || BUTTON_EXISTS(RT))
|
||||
|
||||
#if ENABLED(CARTESIO_UI)
|
||||
#define DOGLCD
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#define DEFAULT_LCD_CONTRAST 90
|
||||
#define LCD_CONTRAST_MIN 60
|
||||
#define LCD_CONTRAST_MAX 140
|
||||
#endif
|
||||
|
||||
#if ENABLED(MAKRPANEL) || ENABLED(MINIPANEL)
|
||||
#define DOGLCD
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#define DEFAULT_LCD_CONTRAST 17
|
||||
#endif
|
||||
|
||||
#if ENABLED(miniVIKI) || ENABLED(VIKI2) || ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
|
||||
#define ULTRA_LCD //general LCD support, also 16x2
|
||||
#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
|
||||
#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
|
||||
|
||||
#if ENABLED(miniVIKI)
|
||||
#define LCD_CONTRAST_MIN 75
|
||||
#define LCD_CONTRAST_MAX 115
|
||||
#define DEFAULT_LCD_CONTRAST 95
|
||||
#elif ENABLED(VIKI2)
|
||||
#define DEFAULT_LCD_CONTRAST 40
|
||||
#elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
|
||||
#define LCD_CONTRAST_MIN 90
|
||||
#define LCD_CONTRAST_MAX 130
|
||||
#define DEFAULT_LCD_CONTRAST 110
|
||||
#define U8GLIB_LM6059_AF
|
||||
#define SD_DETECT_INVERTED
|
||||
#endif
|
||||
|
||||
#define ENCODER_PULSES_PER_STEP 4
|
||||
#define ENCODER_STEPS_PER_MENU_ITEM 1
|
||||
#endif
|
||||
|
||||
// Generic support for SSD1306 / SH1106 OLED based LCDs.
|
||||
#if ENABLED(U8GLIB_SSD1306) || ENABLED(U8GLIB_SH1106)
|
||||
#define ULTRA_LCD //general LCD support, also 16x2
|
||||
#define DOGLCD // Support for I2C LCD 128x64 (Controller SSD1306 / SH1106 graphic Display Family)
|
||||
#endif
|
||||
|
||||
#if ENABLED(PANEL_ONE) || ENABLED(U8GLIB_SH1106)
|
||||
#define ULTIMAKERCONTROLLER
|
||||
#endif
|
||||
|
||||
#if ENABLED(BQ_LCD_SMART_CONTROLLER)
|
||||
#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
|
||||
#ifndef ENCODER_PULSES_PER_STEP
|
||||
#define ENCODER_PULSES_PER_STEP 4
|
||||
#endif
|
||||
|
||||
#ifndef ENCODER_STEPS_PER_MENU_ITEM
|
||||
#define ENCODER_STEPS_PER_MENU_ITEM 1
|
||||
#endif
|
||||
|
||||
#ifndef LONG_FILENAME_HOST_SUPPORT
|
||||
#define LONG_FILENAME_HOST_SUPPORT
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
|
||||
#define DOGLCD
|
||||
#define U8GLIB_ST7920
|
||||
#define REPRAP_DISCOUNT_SMART_CONTROLLER
|
||||
#endif
|
||||
|
||||
#if ENABLED(ULTIMAKERCONTROLLER) \
|
||||
|| ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) \
|
||||
|| ENABLED(G3D_PANEL) \
|
||||
|| ENABLED(RIGIDBOT_PANEL) \
|
||||
|| ENABLED(REPRAPWORLD_KEYPAD)
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#endif
|
||||
|
||||
#if ENABLED(RA_CONTROL_PANEL)
|
||||
#define LCD_I2C_TYPE_PCA8574
|
||||
#define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#endif
|
||||
|
||||
#if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
|
||||
#define DOGLCD
|
||||
#define U8GLIB_ST7920
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#endif
|
||||
|
||||
/**
|
||||
* I2C PANELS
|
||||
*/
|
||||
|
||||
#if ENABLED(LCD_I2C_SAINSMART_YWROBOT)
|
||||
// This uses the LiquidCrystal_I2C library ( https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home )
|
||||
// Make sure it is placed in the Arduino libraries directory.
|
||||
#define LCD_I2C_TYPE_PCF8575
|
||||
#define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#endif
|
||||
|
||||
// PANELOLU2 LCD with status LEDs, separate encoder and click inputs
|
||||
#if ENABLED(LCD_I2C_PANELOLU2)
|
||||
#define LCD_I2C_TYPE_MCP23017
|
||||
#define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
|
||||
#define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD
|
||||
|
||||
#ifndef ENCODER_PULSES_PER_STEP
|
||||
#define ENCODER_PULSES_PER_STEP 4
|
||||
#endif
|
||||
|
||||
#ifndef ENCODER_STEPS_PER_MENU_ITEM
|
||||
#define ENCODER_STEPS_PER_MENU_ITEM 1
|
||||
#endif
|
||||
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#endif
|
||||
|
||||
// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
|
||||
#if ENABLED(LCD_I2C_VIKI)
|
||||
// This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
|
||||
// Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
|
||||
// Note: The pause/stop/resume LCD button pin should be connected to the Arduino
|
||||
// BTN_ENC pin (or set BTN_ENC to -1 if not used)
|
||||
#define LCD_I2C_TYPE_MCP23017
|
||||
#define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
|
||||
#define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later)
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#endif
|
||||
|
||||
// Shift register panels
|
||||
// ---------------------
|
||||
// 2 wire Non-latching LCD SR from:
|
||||
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||||
|
||||
#if ENABLED(SAV_3DLCD)
|
||||
#define SR_LCD_2W_NL // Non latching 2 wire shift register
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#endif
|
||||
|
||||
#if ENABLED(DOGLCD) // Change number of lines to match the DOG graphic display
|
||||
#ifndef LCD_WIDTH
|
||||
#define LCD_WIDTH 22
|
||||
#endif
|
||||
#ifndef LCD_HEIGHT
|
||||
#define LCD_HEIGHT 5
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if ENABLED(ULTIPANEL)
|
||||
#define NEWPANEL //enable this if you have a click-encoder panel
|
||||
#define ULTRA_LCD
|
||||
#ifndef LCD_WIDTH
|
||||
#define LCD_WIDTH 20
|
||||
#endif
|
||||
#ifndef LCD_HEIGHT
|
||||
#define LCD_HEIGHT 4
|
||||
#endif
|
||||
#else //no panel but just LCD
|
||||
#if ENABLED(ULTRA_LCD)
|
||||
#ifndef LCD_WIDTH
|
||||
#define LCD_WIDTH 16
|
||||
#endif
|
||||
#ifndef LCD_HEIGHT
|
||||
#define LCD_HEIGHT 2
|
||||
#endif
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if ENABLED(DOGLCD)
|
||||
/* Custom characters defined in font dogm_font_data_Marlin_symbols.h / Marlin_symbols.fon */
|
||||
// \x00 intentionally skipped to avoid problems in strings
|
||||
#define LCD_STR_REFRESH "\x01"
|
||||
#define LCD_STR_FOLDER "\x02"
|
||||
#define LCD_STR_ARROW_RIGHT "\x03"
|
||||
#define LCD_STR_UPLEVEL "\x04"
|
||||
#define LCD_STR_CLOCK "\x05"
|
||||
#define LCD_STR_FEEDRATE "\x06"
|
||||
#define LCD_STR_BEDTEMP "\x07"
|
||||
#define LCD_STR_THERMOMETER "\x08"
|
||||
#define LCD_STR_DEGREE "\x09"
|
||||
|
||||
#define LCD_STR_SPECIAL_MAX '\x09'
|
||||
// Maximum here is 0x1f because 0x20 is ' ' (space) and the normal charsets begin.
|
||||
// Better stay below 0x10 because DISPLAY_CHARSET_HD44780_WESTERN begins here.
|
||||
#else
|
||||
/* Custom characters defined in the first 8 characters of the LCD */
|
||||
#define LCD_STR_BEDTEMP "\x00" // Print only as a char. This will have 'unexpected' results when used in a string!
|
||||
#define LCD_STR_DEGREE "\x01"
|
||||
#define LCD_STR_THERMOMETER "\x02"
|
||||
#define LCD_STR_UPLEVEL "\x03"
|
||||
#define LCD_STR_REFRESH "\x04"
|
||||
#define LCD_STR_FOLDER "\x05"
|
||||
#define LCD_STR_FEEDRATE "\x06"
|
||||
#define LCD_STR_CLOCK "\x07"
|
||||
#define LCD_STR_ARROW_RIGHT ">" /* from the default character set */
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Default LCD contrast for dogm-like LCD displays
|
||||
*/
|
||||
#if ENABLED(DOGLCD)
|
||||
|
||||
#define HAS_LCD_CONTRAST ( \
|
||||
ENABLED(MAKRPANEL) \
|
||||
|| ENABLED(CARTESIO_UI) \
|
||||
|| ENABLED(VIKI2) \
|
||||
|| ENABLED(miniVIKI) \
|
||||
|| ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) \
|
||||
)
|
||||
|
||||
#if HAS_LCD_CONTRAST
|
||||
#ifndef LCD_CONTRAST_MIN
|
||||
#define LCD_CONTRAST_MIN 0
|
||||
#endif
|
||||
#ifndef LCD_CONTRAST_MAX
|
||||
#define LCD_CONTRAST_MAX 63
|
||||
#endif
|
||||
#ifndef DEFAULT_LCD_CONTRAST
|
||||
#define DEFAULT_LCD_CONTRAST 32
|
||||
#endif
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#ifndef BOOTSCREEN_TIMEOUT
|
||||
#define BOOTSCREEN_TIMEOUT 2500
|
||||
#endif
|
||||
|
||||
#endif //CONDITIONALS_LCD_H
|
||||
@ -0,0 +1,39 @@
|
||||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
|
||||
#ifndef MARLIN_CONFIG_H
|
||||
#define MARLIN_CONFIG_H
|
||||
|
||||
#include "macros.h"
|
||||
#include "boards.h"
|
||||
#include "Version.h"
|
||||
#include "Configuration.h"
|
||||
#include "Conditionals_LCD.h"
|
||||
#include "Configuration_adv.h"
|
||||
#include "pins.h"
|
||||
#ifndef USBCON
|
||||
#define HardwareSerial_h // trick to disable the standard HWserial
|
||||
#endif
|
||||
#include "Arduino.h"
|
||||
#include "Conditionals_post.h"
|
||||
|
||||
#endif // MARLIN_CONFIG_H
|
||||
@ -0,0 +1,729 @@
|
||||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* SanityCheck.cpp
|
||||
*
|
||||
* Test configuration values for errors at compile-time.
|
||||
* This is done only once, here, to speed up compilation time.
|
||||
*/
|
||||
#include "MarlinConfig.h"
|
||||
|
||||
/**
|
||||
* Due to the high number of issues related with old versions of Arduino IDE
|
||||
* we are now warning our users to update their toolkits. In a future Marlin
|
||||
* release we will stop supporting old IDE versions and will require user
|
||||
* action to proceed with compilation in such environments.
|
||||
*/
|
||||
#if !defined(ARDUINO) || ARDUINO < 10600
|
||||
#error "Versions of Arduino IDE prior to 1.6.0 are no longer supported, please update your toolkit."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* We try our best to include sanity checks for all the changes configuration
|
||||
* directives because people have a tendency to use outdated config files with
|
||||
* the bleding edge source code, but sometimes this is not enough. This check
|
||||
* will force a minimum config file revision, otherwise Marlin will not build.
|
||||
*/
|
||||
#if ! defined(CONFIGURATION_H_VERSION) || CONFIGURATION_H_VERSION < REQUIRED_CONFIGURATION_H_VERSION
|
||||
#error "You are using an old Configuration.h file, update it before building Marlin."
|
||||
#endif
|
||||
|
||||
#if ! defined(CONFIGURATION_ADV_H_VERSION) || CONFIGURATION_ADV_H_VERSION < REQUIRED_CONFIGURATION_ADV_H_VERSION
|
||||
#error "You are using an old Configuration_adv.h file, update it before building Marlin."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Marlin release, version and default string
|
||||
*/
|
||||
#ifndef SHORT_BUILD_VERSION
|
||||
#error "SHORT_BUILD_VERSION must be specified."
|
||||
#elif !defined(DETAILED_BUILD_VERSION)
|
||||
#error "BUILD_VERSION must be specified."
|
||||
#elif !defined(STRING_DISTRIBUTION_DATE)
|
||||
#error "STRING_DISTRIBUTION_DATE must be specified."
|
||||
#elif !defined(PROTOCOL_VERSION)
|
||||
#error "PROTOCOL_VERSION must be specified."
|
||||
#elif !defined(MACHINE_NAME)
|
||||
#error "MACHINE_NAME must be specified."
|
||||
#elif !defined(SOURCE_CODE_URL)
|
||||
#error "SOURCE_CODE_URL must be specified."
|
||||
#elif !defined(DEFAULT_MACHINE_UUID)
|
||||
#error "DEFAULT_MACHINE_UUID must be specified."
|
||||
#elif !defined(WEBSITE_URL)
|
||||
#error "WEBSITE_URL must be specified."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Dual Stepper Drivers
|
||||
*/
|
||||
#if ENABLED(X_DUAL_STEPPER_DRIVERS) && ENABLED(DUAL_X_CARRIAGE)
|
||||
#error "DUAL_X_CARRIAGE is not compatible with X_DUAL_STEPPER_DRIVERS."
|
||||
#elif ENABLED(X_DUAL_STEPPER_DRIVERS) && (!HAS_X2_ENABLE || !HAS_X2_STEP || !HAS_X2_DIR)
|
||||
#error "X_DUAL_STEPPER_DRIVERS requires X2 pins (and an extra E plug)."
|
||||
#elif ENABLED(Y_DUAL_STEPPER_DRIVERS) && (!HAS_Y2_ENABLE || !HAS_Y2_STEP || !HAS_Y2_DIR)
|
||||
#error "Y_DUAL_STEPPER_DRIVERS requires Y2 pins (and an extra E plug)."
|
||||
#elif ENABLED(Z_DUAL_STEPPER_DRIVERS) && (!HAS_Z2_ENABLE || !HAS_Z2_STEP || !HAS_Z2_DIR)
|
||||
#error "Z_DUAL_STEPPER_DRIVERS requires Z2 pins (and an extra E plug)."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Progress Bar
|
||||
*/
|
||||
#if ENABLED(LCD_PROGRESS_BAR)
|
||||
#if DISABLED(SDSUPPORT)
|
||||
#error "LCD_PROGRESS_BAR requires SDSUPPORT."
|
||||
#endif
|
||||
#if ENABLED(DOGLCD)
|
||||
#error "LCD_PROGRESS_BAR does not apply to graphical displays."
|
||||
#endif
|
||||
#if ENABLED(FILAMENT_LCD_DISPLAY)
|
||||
#error "LCD_PROGRESS_BAR and FILAMENT_LCD_DISPLAY are not fully compatible. Comment out this line to use both."
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Babystepping
|
||||
*/
|
||||
#if ENABLED(BABYSTEPPING)
|
||||
#if DISABLED(ULTRA_LCD)
|
||||
#error "BABYSTEPPING requires an LCD controller."
|
||||
#endif
|
||||
#if ENABLED(SCARA)
|
||||
#error "BABYSTEPPING is not implemented for SCARA yet."
|
||||
#endif
|
||||
#if ENABLED(DELTA) && ENABLED(BABYSTEP_XY)
|
||||
#error "BABYSTEPPING only implemented for Z axis on deltabots."
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Filament Runout needs a pin and either SD Support or Auto print start detection
|
||||
*/
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#if !HAS_FIL_RUNOUT
|
||||
#error "FILAMENT_RUNOUT_SENSOR requires FIL_RUNOUT_PIN."
|
||||
#elif DISABLED(SDSUPPORT) && DISABLED(PRINTJOB_TIMER_AUTOSTART)
|
||||
#error "FILAMENT_RUNOUT_SENSOR requires SDSUPPORT or PRINTJOB_TIMER_AUTOSTART."
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Filament Change with Extruder Runout Prevention
|
||||
*/
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE) && ENABLED(EXTRUDER_RUNOUT_PREVENT)
|
||||
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with FILAMENT_CHANGE_FEATURE."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Individual axis homing is useless for DELTAS
|
||||
*/
|
||||
#if ENABLED(INDIVIDUAL_AXIS_HOMING_MENU) && ENABLED(DELTA)
|
||||
#error "INDIVIDUAL_AXIS_HOMING_MENU is incompatible with DELTA kinematics."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Options only for EXTRUDERS > 1
|
||||
*/
|
||||
#if EXTRUDERS > 1
|
||||
|
||||
#if EXTRUDERS > 4
|
||||
#error "The maximum number of EXTRUDERS in Marlin is 4."
|
||||
#endif
|
||||
|
||||
#if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT)
|
||||
#error "EXTRUDERS must be 1 with TEMP_SENSOR_1_AS_REDUNDANT."
|
||||
#endif
|
||||
|
||||
#if ENABLED(HEATERS_PARALLEL)
|
||||
#error "EXTRUDERS must be 1 with HEATERS_PARALLEL."
|
||||
#endif
|
||||
|
||||
#elif ENABLED(SINGLENOZZLE)
|
||||
#error "SINGLENOZZLE requires 2 or more EXTRUDERS."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Only one type of extruder allowed
|
||||
*/
|
||||
#if (ENABLED(SWITCHING_EXTRUDER) && (ENABLED(SINGLENOZZLE) || ENABLED(MIXING_EXTRUDER))) \
|
||||
|| (ENABLED(SINGLENOZZLE) && ENABLED(MIXING_EXTRUDER))
|
||||
#error "Please define only one type of extruder: SINGLENOZZLE, SWITCHING_EXTRUDER, or MIXING_EXTRUDER."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Single Stepper Dual Extruder with switching servo
|
||||
*/
|
||||
#if ENABLED(SWITCHING_EXTRUDER)
|
||||
#if ENABLED(DUAL_X_CARRIAGE)
|
||||
#error "SWITCHING_EXTRUDER and DUAL_X_CARRIAGE are incompatible."
|
||||
#elif EXTRUDERS != 2
|
||||
#error "SWITCHING_EXTRUDER requires exactly 2 EXTRUDERS."
|
||||
#elif NUM_SERVOS < 1
|
||||
#error "SWITCHING_EXTRUDER requires NUM_SERVOS >= 1."
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Mixing Extruder requirements
|
||||
*/
|
||||
#if ENABLED(MIXING_EXTRUDER)
|
||||
#if EXTRUDERS > 1
|
||||
#error "MIXING_EXTRUDER currently only supports one extruder."
|
||||
#endif
|
||||
#if MIXING_STEPPERS < 2
|
||||
#error "You must set MIXING_STEPPERS >= 2 for a mixing extruder."
|
||||
#endif
|
||||
#if ENABLED(FILAMENT_SENSOR)
|
||||
#error "MIXING_EXTRUDER is incompatible with FILAMENT_SENSOR. Comment out this line to use it anyway."
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Limited number of servos
|
||||
*/
|
||||
#if defined(NUM_SERVOS) && NUM_SERVOS > 0
|
||||
#if NUM_SERVOS > 4
|
||||
#error "The maximum number of SERVOS in Marlin is 4."
|
||||
#elif HAS_Z_SERVO_ENDSTOP && Z_ENDSTOP_SERVO_NR >= NUM_SERVOS
|
||||
#error "Z_ENDSTOP_SERVO_NR must be smaller than NUM_SERVOS."
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Servo deactivation depends on servo endstops
|
||||
*/
|
||||
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE) && !HAS_Z_SERVO_ENDSTOP
|
||||
#error "Z_ENDSTOP_SERVO_NR is required for DEACTIVATE_SERVOS_AFTER_MOVE."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Required LCD language
|
||||
*/
|
||||
#if DISABLED(DOGLCD) && ENABLED(ULTRA_LCD) && !defined(DISPLAY_CHARSET_HD44780)
|
||||
#error "You must set DISPLAY_CHARSET_HD44780 to JAPANESE, WESTERN or CYRILLIC for your LCD controller."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Bed Heating Options - PID vs Limit Switching
|
||||
*/
|
||||
#if ENABLED(PIDTEMPBED) && ENABLED(BED_LIMIT_SWITCHING)
|
||||
#error "To use BED_LIMIT_SWITCHING you must disable PIDTEMPBED."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Mesh Bed Leveling
|
||||
*/
|
||||
#if ENABLED(MESH_BED_LEVELING)
|
||||
#if ENABLED(DELTA)
|
||||
#error "MESH_BED_LEVELING does not yet support DELTA printers."
|
||||
#elif ENABLED(AUTO_BED_LEVELING_FEATURE)
|
||||
#error "Select AUTO_BED_LEVELING_FEATURE or MESH_BED_LEVELING, not both."
|
||||
#elif MESH_NUM_X_POINTS > 9 || MESH_NUM_Y_POINTS > 9
|
||||
#error "MESH_NUM_X_POINTS and MESH_NUM_Y_POINTS must be less than 10."
|
||||
#endif
|
||||
#elif ENABLED(MANUAL_BED_LEVELING)
|
||||
#error "MESH_BED_LEVELING is required for MANUAL_BED_LEVELING."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Probes
|
||||
*/
|
||||
|
||||
#if PROBE_SELECTED
|
||||
|
||||
#if ENABLED(Z_PROBE_SLED) && ENABLED(DELTA)
|
||||
#error "You cannot use Z_PROBE_SLED with DELTA."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* NUM_SERVOS is required for a Z servo probe
|
||||
*/
|
||||
#if HAS_Z_SERVO_ENDSTOP
|
||||
#ifndef NUM_SERVOS
|
||||
#error "You must set NUM_SERVOS for a Z servo probe (Z_ENDSTOP_SERVO_NR)."
|
||||
#elif Z_ENDSTOP_SERVO_NR >= NUM_SERVOS
|
||||
#error "Z_ENDSTOP_SERVO_NR must be less than NUM_SERVOS."
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* A probe needs a pin
|
||||
*/
|
||||
#if !PROBE_PIN_CONFIGURED
|
||||
#error "A probe needs a pin! Use Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN or Z_MIN_PROBE_PIN."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Z_MIN_PIN and Z_MIN_PROBE_PIN can't co-exist when Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
*/
|
||||
#if HAS_Z_MIN && HAS_Z_MIN_PROBE_PIN && ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
|
||||
#error "A probe cannot have more than one pin! Use Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN or Z_MIN_PROBE_PIN."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Make sure the plug is enabled if it's used
|
||||
*/
|
||||
#if ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) && DISABLED(USE_ZMIN_PLUG)
|
||||
#error "You must enable USE_ZMIN_PLUG if any probe or endstop is connected to the ZMIN plug."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Only allow one probe option to be defined
|
||||
*/
|
||||
#if (ENABLED(FIX_MOUNTED_PROBE) && (ENABLED(Z_PROBE_ALLEN_KEY) || HAS_Z_SERVO_ENDSTOP || ENABLED(Z_PROBE_SLED))) \
|
||||
|| (ENABLED(Z_PROBE_ALLEN_KEY) && (HAS_Z_SERVO_ENDSTOP || ENABLED(Z_PROBE_SLED))) \
|
||||
|| (HAS_Z_SERVO_ENDSTOP && ENABLED(Z_PROBE_SLED))
|
||||
#error "Please define only one type of probe: Z Servo, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or FIX_MOUNTED_PROBE."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Don't allow nonsense probe-pin settings
|
||||
*/
|
||||
#if ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) && ENABLED(Z_MIN_PROBE_ENDSTOP)
|
||||
#error "You can't enable both Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN and Z_MIN_PROBE_ENDSTOP."
|
||||
#elif ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) && ENABLED(DISABLE_Z_MIN_PROBE_ENDSTOP)
|
||||
#error "Don't enable DISABLE_Z_MIN_PROBE_ENDSTOP with Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN."
|
||||
#elif ENABLED(DISABLE_Z_MIN_PROBE_ENDSTOP) && DISABLED(Z_MIN_PROBE_ENDSTOP)
|
||||
#error "DISABLE_Z_MIN_PROBE_ENDSTOP requires Z_MIN_PROBE_ENDSTOP to be set."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Require a Z probe pin if Z_MIN_PROBE_ENDSTOP is enabled.
|
||||
*/
|
||||
#if ENABLED(Z_MIN_PROBE_ENDSTOP)
|
||||
#if !HAS_Z_MIN_PROBE_PIN
|
||||
#error "Z_MIN_PROBE_ENDSTOP requires a Z_MIN_PROBE_PIN in your board's pins_XXXX.h file."
|
||||
#endif
|
||||
// Forcing Servo definitions can break some hall effect sensor setups. Leaving these here for further comment.
|
||||
//#ifndef NUM_SERVOS
|
||||
// #error "You must have NUM_SERVOS defined and there must be at least 1 configured to use Z_MIN_PROBE_ENDSTOP."
|
||||
//#endif
|
||||
//#if defined(NUM_SERVOS) && NUM_SERVOS < 1
|
||||
// #error "You must have at least 1 servo defined for NUM_SERVOS to use Z_MIN_PROBE_ENDSTOP."
|
||||
//#endif
|
||||
//#if Z_ENDSTOP_SERVO_NR < 0
|
||||
// #error "You must have Z_ENDSTOP_SERVO_NR set to at least 0 or above to use Z_MIN_PROBE_ENDSTOP."
|
||||
//#endif
|
||||
//#ifndef Z_SERVO_ANGLES
|
||||
// #error "You must have Z_SERVO_ANGLES defined for Z Extend and Retract to use Z_MIN_PROBE_ENDSTOP."
|
||||
//#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Make sure Z raise values are set
|
||||
*/
|
||||
#if defined(Z_RAISE_BEFORE_PROBING) || defined(Z_RAISE_AFTER_PROBING)
|
||||
#error "Z_RAISE_(BEFORE|AFTER)_PROBING are deprecated. Use Z_RAISE_PROBE_DEPLOY_STOW instead."
|
||||
#elif !defined(Z_RAISE_PROBE_DEPLOY_STOW)
|
||||
#error "You must set Z_RAISE_PROBE_DEPLOY_STOW in your configuration."
|
||||
#elif !defined(Z_RAISE_BETWEEN_PROBINGS)
|
||||
#error "You must set Z_RAISE_BETWEEN_PROBINGS in your configuration."
|
||||
#elif Z_RAISE_PROBE_DEPLOY_STOW < 1
|
||||
#error "Probes need Z_RAISE_PROBE_DEPLOY_STOW >= 1."
|
||||
#elif Z_RAISE_BETWEEN_PROBINGS < 1
|
||||
#error "Probes need Z_RAISE_BETWEEN_PROBINGS >= 1."
|
||||
#endif
|
||||
|
||||
#else
|
||||
|
||||
/**
|
||||
* Require some kind of probe for bed leveling and probe testing
|
||||
*/
|
||||
#if ENABLED(AUTO_BED_LEVELING_FEATURE)
|
||||
#error "AUTO_BED_LEVELING_FEATURE requires a probe! Define a Z Servo, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or FIX_MOUNTED_PROBE."
|
||||
#elif ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST)
|
||||
#error "Z_MIN_PROBE_REPEATABILITY_TEST requires a probe! Define a Z Servo, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or FIX_MOUNTED_PROBE."
|
||||
#elif ENABLED(Z_SAFE_HOMING)
|
||||
#error "Z_SAFE_HOMING currently requires a probe."
|
||||
#endif
|
||||
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Make sure Z_SAFE_HOMING point is reachable
|
||||
*/
|
||||
#if ENABLED(Z_SAFE_HOMING)
|
||||
#if Z_SAFE_HOMING_X_POINT < MIN_PROBE_X || Z_SAFE_HOMING_X_POINT > MAX_PROBE_X
|
||||
#error "The given Z_SAFE_HOMING_X_POINT can't be reached by the Z probe."
|
||||
#elif Z_SAFE_HOMING_Y_POINT < MIN_PROBE_Y || Z_SAFE_HOMING_Y_POINT > MAX_PROBE_Y
|
||||
#error "The given Z_SAFE_HOMING_Y_POINT can't be reached by the Z probe."
|
||||
#endif
|
||||
#endif // Z_SAFE_HOMING
|
||||
|
||||
/**
|
||||
* Auto Bed Leveling
|
||||
*/
|
||||
#if ENABLED(AUTO_BED_LEVELING_FEATURE)
|
||||
|
||||
/**
|
||||
* Delta has limited bed leveling options
|
||||
*/
|
||||
#if ENABLED(DELTA) && DISABLED(AUTO_BED_LEVELING_GRID)
|
||||
#error "You must use AUTO_BED_LEVELING_GRID for DELTA bed leveling."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Require a Z min pin
|
||||
*/
|
||||
#if !PIN_EXISTS(Z_MIN)
|
||||
#if !PIN_EXISTS(Z_MIN_PROBE) || (DISABLED(Z_MIN_PROBE_ENDSTOP) || ENABLED(DISABLE_Z_MIN_PROBE_ENDSTOP)) // It's possible for someone to set a pin for the Z probe, but not enable it.
|
||||
#error "AUTO_BED_LEVELING_FEATURE requires a Z_MIN or Z_PROBE endstop. Z_MIN_PIN or Z_MIN_PROBE_PIN must point to a valid hardware pin."
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Check if Probe_Offset * Grid Points is greater than Probing Range
|
||||
*/
|
||||
#if ENABLED(AUTO_BED_LEVELING_GRID)
|
||||
#ifndef DELTA_PROBEABLE_RADIUS
|
||||
// Be sure points are in the right order
|
||||
#if LEFT_PROBE_BED_POSITION > RIGHT_PROBE_BED_POSITION
|
||||
#error "LEFT_PROBE_BED_POSITION must be less than RIGHT_PROBE_BED_POSITION."
|
||||
#elif FRONT_PROBE_BED_POSITION > BACK_PROBE_BED_POSITION
|
||||
#error "FRONT_PROBE_BED_POSITION must be less than BACK_PROBE_BED_POSITION."
|
||||
#endif
|
||||
// Make sure probing points are reachable
|
||||
#if LEFT_PROBE_BED_POSITION < MIN_PROBE_X
|
||||
#error "The given LEFT_PROBE_BED_POSITION can't be reached by the Z probe."
|
||||
#elif RIGHT_PROBE_BED_POSITION > MAX_PROBE_X
|
||||
#error "The given RIGHT_PROBE_BED_POSITION can't be reached by the Z probe."
|
||||
#elif FRONT_PROBE_BED_POSITION < MIN_PROBE_Y
|
||||
#error "The given FRONT_PROBE_BED_POSITION can't be reached by the Z probe."
|
||||
#elif BACK_PROBE_BED_POSITION > MAX_PROBE_Y
|
||||
#error "The given BACK_PROBE_BED_POSITION can't be reached by the Z probe."
|
||||
#endif
|
||||
#endif
|
||||
#else // !AUTO_BED_LEVELING_GRID
|
||||
|
||||
// Check the triangulation points
|
||||
#if ABL_PROBE_PT_1_X < MIN_PROBE_X || ABL_PROBE_PT_1_X > MAX_PROBE_X
|
||||
#error "The given ABL_PROBE_PT_1_X can't be reached by the Z probe."
|
||||
#elif ABL_PROBE_PT_2_X < MIN_PROBE_X || ABL_PROBE_PT_2_X > MAX_PROBE_X
|
||||
#error "The given ABL_PROBE_PT_2_X can't be reached by the Z probe."
|
||||
#elif ABL_PROBE_PT_3_X < MIN_PROBE_X || ABL_PROBE_PT_3_X > MAX_PROBE_X
|
||||
#error "The given ABL_PROBE_PT_3_X can't be reached by the Z probe."
|
||||
#elif ABL_PROBE_PT_1_Y < MIN_PROBE_Y || ABL_PROBE_PT_1_Y > MAX_PROBE_Y
|
||||
#error "The given ABL_PROBE_PT_1_Y can't be reached by the Z probe."
|
||||
#elif ABL_PROBE_PT_2_Y < MIN_PROBE_Y || ABL_PROBE_PT_2_Y > MAX_PROBE_Y
|
||||
#error "The given ABL_PROBE_PT_2_Y can't be reached by the Z probe."
|
||||
#elif ABL_PROBE_PT_3_Y < MIN_PROBE_Y || ABL_PROBE_PT_3_Y > MAX_PROBE_Y
|
||||
#error "The given ABL_PROBE_PT_3_Y can't be reached by the Z probe."
|
||||
#endif
|
||||
|
||||
#endif // !AUTO_BED_LEVELING_GRID
|
||||
|
||||
#endif // AUTO_BED_LEVELING_FEATURE
|
||||
|
||||
/**
|
||||
* Advance Extrusion
|
||||
*/
|
||||
#if ENABLED(ADVANCE) && ENABLED(LIN_ADVANCE)
|
||||
#error "You can enable ADVANCE or LIN_ADVANCE, but not both."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Filament Width Sensor
|
||||
*/
|
||||
#if ENABLED(FILAMENT_WIDTH_SENSOR) && !HAS_FILAMENT_WIDTH_SENSOR
|
||||
#error "FILAMENT_WIDTH_SENSOR requires a FILWIDTH_PIN to be defined."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* ULTIPANEL encoder
|
||||
*/
|
||||
#if ENABLED(ULTIPANEL) && DISABLED(NEWPANEL) && DISABLED(SR_LCD_2W_NL) && !defined(SHIFT_CLK)
|
||||
#error "ULTIPANEL requires some kind of encoder."
|
||||
#endif
|
||||
|
||||
#if ENCODER_PULSES_PER_STEP < 0
|
||||
#error "ENCODER_PULSES_PER_STEP should not be negative, use REVERSE_MENU_DIRECTION instead."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* SAV_3DGLCD display options
|
||||
*/
|
||||
#if ENABLED(U8GLIB_SSD1306) && ENABLED(U8GLIB_SH1106)
|
||||
#error "Only enable one SAV_3DGLCD display type: U8GLIB_SSD1306 or U8GLIB_SH1106."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Don't set more than one kinematic type
|
||||
*/
|
||||
#if (ENABLED(DELTA) && (ENABLED(SCARA) || ENABLED(COREXY) || ENABLED(COREXZ) || ENABLED(COREYZ))) \
|
||||
|| (ENABLED(SCARA) && (ENABLED(COREXY) || ENABLED(COREXZ) || ENABLED(COREYZ))) \
|
||||
|| (ENABLED(COREXY) && (ENABLED(COREXZ) || ENABLED(COREYZ))) \
|
||||
|| (ENABLED(COREXZ) && ENABLED(COREYZ))
|
||||
#error "Please enable only one of DELTA, SCARA, COREXY, COREXZ, or COREYZ."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Allen Key
|
||||
* Deploying the Allen Key probe uses big moves in z direction. Too dangerous for an unhomed z-axis.
|
||||
*/
|
||||
#if ENABLED(Z_PROBE_ALLEN_KEY) && (Z_HOME_DIR < 0) && ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
|
||||
#error "You can't home to a z min endstop with a Z_PROBE_ALLEN_KEY"
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Dual X Carriage requirements
|
||||
*/
|
||||
#if ENABLED(DUAL_X_CARRIAGE)
|
||||
#if EXTRUDERS == 1
|
||||
#error "DUAL_X_CARRIAGE requires 2 (or more) extruders."
|
||||
#elif ENABLED(COREXY) || ENABLED(COREXZ)
|
||||
#error "DUAL_X_CARRIAGE cannot be used with COREXY or COREXZ."
|
||||
#elif !HAS_X2_ENABLE || !HAS_X2_STEP || !HAS_X2_DIR
|
||||
#error "DUAL_X_CARRIAGE requires X2 stepper pins to be defined."
|
||||
#elif !HAS_X_MAX
|
||||
#error "DUAL_X_CARRIAGE requires USE_XMAX_PLUG and an X Max Endstop."
|
||||
#elif !defined(X2_HOME_POS) || !defined(X2_MIN_POS) || !defined(X2_MAX_POS)
|
||||
#error "DUAL_X_CARRIAGE requires X2_HOME_POS, X2_MIN_POS, and X2_MAX_POS."
|
||||
#elif X_HOME_DIR != -1 || X2_HOME_DIR != 1
|
||||
#error "DUAL_X_CARRIAGE requires X_HOME_DIR -1 and X2_HOME_DIR 1."
|
||||
#endif
|
||||
#endif // DUAL_X_CARRIAGE
|
||||
|
||||
/**
|
||||
* Make sure auto fan pins don't conflict with the fan pin
|
||||
*/
|
||||
#if HAS_AUTO_FAN
|
||||
#if HAS_FAN0
|
||||
#if EXTRUDER_0_AUTO_FAN_PIN == FAN_PIN
|
||||
#error "You cannot set EXTRUDER_0_AUTO_FAN_PIN equal to FAN_PIN."
|
||||
#elif EXTRUDER_1_AUTO_FAN_PIN == FAN_PIN
|
||||
#error "You cannot set EXTRUDER_1_AUTO_FAN_PIN equal to FAN_PIN."
|
||||
#elif EXTRUDER_2_AUTO_FAN_PIN == FAN_PIN
|
||||
#error "You cannot set EXTRUDER_2_AUTO_FAN_PIN equal to FAN_PIN."
|
||||
#elif EXTRUDER_3_AUTO_FAN_PIN == FAN_PIN
|
||||
#error "You cannot set EXTRUDER_3_AUTO_FAN_PIN equal to FAN_PIN."
|
||||
#endif
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if HAS_FAN0 && CONTROLLERFAN_PIN == FAN_PIN
|
||||
#error "You cannot set CONTROLLERFAN_PIN equal to FAN_PIN."
|
||||
#endif
|
||||
|
||||
#if HAS_CONTROLLERFAN
|
||||
#if EXTRUDER_0_AUTO_FAN_PIN == CONTROLLERFAN_PIN
|
||||
#error "You cannot set EXTRUDER_0_AUTO_FAN_PIN equal to CONTROLLERFAN_PIN."
|
||||
#elif EXTRUDER_1_AUTO_FAN_PIN == CONTROLLERFAN_PIN
|
||||
#error "You cannot set EXTRUDER_1_AUTO_FAN_PIN equal to CONTROLLERFAN_PIN."
|
||||
#elif EXTRUDER_2_AUTO_FAN_PIN == CONTROLLERFAN_PIN
|
||||
#error "You cannot set EXTRUDER_2_AUTO_FAN_PIN equal to CONTROLLERFAN_PIN."
|
||||
#elif EXTRUDER_3_AUTO_FAN_PIN == CONTROLLERFAN_PIN
|
||||
#error "You cannot set EXTRUDER_3_AUTO_FAN_PIN equal to CONTROLLERFAN_PIN."
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Test Heater, Temp Sensor, and Extruder Pins; Sensor Type must also be set.
|
||||
*/
|
||||
#if !HAS_HEATER_0
|
||||
#error "HEATER_0_PIN not defined for this board."
|
||||
#elif !PIN_EXISTS(TEMP_0)
|
||||
#error "TEMP_0_PIN not defined for this board."
|
||||
#elif !PIN_EXISTS(E0_STEP) || !PIN_EXISTS(E0_DIR) || !PIN_EXISTS(E0_ENABLE)
|
||||
#error "E0_STEP_PIN, E0_DIR_PIN, or E0_ENABLE_PIN not defined for this board."
|
||||
#elif TEMP_SENSOR_0 == 0
|
||||
#error "TEMP_SENSOR_0 is required."
|
||||
#endif
|
||||
|
||||
#if HOTENDS > 1 || ENABLED(HEATERS_PARALLEL)
|
||||
#if !HAS_HEATER_1
|
||||
#error "HEATER_1_PIN not defined for this board."
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if HOTENDS > 1
|
||||
#if TEMP_SENSOR_1 == 0
|
||||
#error "TEMP_SENSOR_1 is required with 2 or more HOTENDS."
|
||||
#elif !PIN_EXISTS(TEMP_1)
|
||||
#error "TEMP_1_PIN not defined for this board."
|
||||
#endif
|
||||
#if HOTENDS > 2
|
||||
#if TEMP_SENSOR_2 == 0
|
||||
#error "TEMP_SENSOR_2 is required with 3 or more HOTENDS."
|
||||
#elif !HAS_HEATER_2
|
||||
#error "HEATER_2_PIN not defined for this board."
|
||||
#elif !PIN_EXISTS(TEMP_2)
|
||||
#error "TEMP_2_PIN not defined for this board."
|
||||
#endif
|
||||
#if HOTENDS > 3
|
||||
#if TEMP_SENSOR_3 == 0
|
||||
#error "TEMP_SENSOR_3 is required with 4 HOTENDS."
|
||||
#elif !HAS_HEATER_3
|
||||
#error "HEATER_3_PIN not defined for this board."
|
||||
#elif !PIN_EXISTS(TEMP_3)
|
||||
#error "TEMP_3_PIN not defined for this board."
|
||||
#endif
|
||||
#elif TEMP_SENSOR_3 != 0
|
||||
#error "TEMP_SENSOR_3 shouldn't be set with only 3 extruders."
|
||||
#endif
|
||||
#elif TEMP_SENSOR_2 != 0
|
||||
#error "TEMP_SENSOR_2 shouldn't be set with only 2 extruders."
|
||||
#elif TEMP_SENSOR_3 != 0
|
||||
#error "TEMP_SENSOR_3 shouldn't be set with only 2 extruders."
|
||||
#endif
|
||||
#elif TEMP_SENSOR_1 != 0 && DISABLED(TEMP_SENSOR_1_AS_REDUNDANT)
|
||||
#error "TEMP_SENSOR_1 shouldn't be set with only 1 extruder."
|
||||
#elif TEMP_SENSOR_2 != 0
|
||||
#error "TEMP_SENSOR_2 shouldn't be set with only 1 extruder."
|
||||
#elif TEMP_SENSOR_3 != 0
|
||||
#error "TEMP_SENSOR_3 shouldn't be set with only 1 extruder."
|
||||
#endif
|
||||
|
||||
#if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT) && TEMP_SENSOR_1 == 0
|
||||
#error "TEMP_SENSOR_1 is required with TEMP_SENSOR_1_AS_REDUNDANT."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Basic 2-nozzle duplication mode
|
||||
*/
|
||||
#if ENABLED(DUAL_NOZZLE_DUPLICATION_MODE)
|
||||
#if HOTENDS != 2
|
||||
#error "DUAL_NOZZLE_DUPLICATION_MODE requires exactly 2 hotends."
|
||||
#elif ENABLED(DUAL_X_CARRIAGE)
|
||||
#error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with DUAL_X_CARRIAGE."
|
||||
#elif ENABLED(SINGLENOZZLE)
|
||||
#error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with SINGLENOZZLE."
|
||||
#elif ENABLED(MIXING_EXTRUDER)
|
||||
#error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with MIXING_EXTRUDER."
|
||||
#elif ENABLED(SWITCHING_EXTRUDER)
|
||||
#error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with SWITCHING_EXTRUDER."
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Test Extruder Pins
|
||||
*/
|
||||
#if EXTRUDERS > 3
|
||||
#if !PIN_EXISTS(E3_STEP) || !PIN_EXISTS(E3_DIR) || !PIN_EXISTS(E3_ENABLE)
|
||||
#error "E3_STEP_PIN, E3_DIR_PIN, or E3_ENABLE_PIN not defined for this board."
|
||||
#endif
|
||||
#elif EXTRUDERS > 2
|
||||
#if !PIN_EXISTS(E2_STEP) || !PIN_EXISTS(E2_DIR) || !PIN_EXISTS(E2_ENABLE)
|
||||
#error "E2_STEP_PIN, E2_DIR_PIN, or E2_ENABLE_PIN not defined for this board."
|
||||
#endif
|
||||
#elif EXTRUDERS > 1
|
||||
#if !PIN_EXISTS(E1_STEP) || !PIN_EXISTS(E1_DIR) || !PIN_EXISTS(E1_ENABLE)
|
||||
#error "E1_STEP_PIN, E1_DIR_PIN, or E1_ENABLE_PIN not defined for this board."
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Endstops
|
||||
*/
|
||||
#if DISABLED(USE_XMIN_PLUG) && DISABLED(USE_XMAX_PLUG) && !(ENABLED(Z_DUAL_ENDSTOPS) && Z2_USE_ENDSTOP >= _XMAX_ && Z2_USE_ENDSTOP <= _XMIN_)
|
||||
#error "You must enable USE_XMIN_PLUG or USE_XMAX_PLUG"
|
||||
#elif DISABLED(USE_YMIN_PLUG) && DISABLED(USE_YMAX_PLUG) && !(ENABLED(Z_DUAL_ENDSTOPS) && Z2_USE_ENDSTOP >= _YMAX_ && Z2_USE_ENDSTOP <= _YMIN_)
|
||||
#error "You must enable USE_YMIN_PLUG or USE_YMAX_PLUG"
|
||||
#elif DISABLED(USE_ZMIN_PLUG) && DISABLED(USE_ZMAX_PLUG) && !(ENABLED(Z_DUAL_ENDSTOPS) && Z2_USE_ENDSTOP >= _ZMAX_ && Z2_USE_ENDSTOP <= _ZMIN_)
|
||||
#error "You must enable USE_ZMIN_PLUG or USE_ZMAX_PLUG"
|
||||
#elif ENABLED(Z_DUAL_ENDSTOPS) && !Z2_USE_ENDSTOP
|
||||
#error "You must set Z2_USE_ENDSTOP with Z_DUAL_ENDSTOPS"
|
||||
#endif
|
||||
|
||||
/**
|
||||
* emergency-command parser
|
||||
*/
|
||||
#if ENABLED(EMERGENCY_PARSER) && ENABLED(USBCON)
|
||||
#error "EMERGENCY_PARSER does not work on boards with AT90USB processors (USBCON)."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Warnings for old configurations
|
||||
*/
|
||||
#if WATCH_TEMP_PERIOD > 500
|
||||
#error "WATCH_TEMP_PERIOD now uses seconds instead of milliseconds."
|
||||
#elif DISABLED(THERMAL_PROTECTION_HOTENDS) && (defined(WATCH_TEMP_PERIOD) || defined(THERMAL_PROTECTION_PERIOD))
|
||||
#error "Thermal Runaway Protection for hotends is now enabled with THERMAL_PROTECTION_HOTENDS."
|
||||
#elif DISABLED(THERMAL_PROTECTION_BED) && defined(THERMAL_PROTECTION_BED_PERIOD)
|
||||
#error "Thermal Runaway Protection for the bed is now enabled with THERMAL_PROTECTION_BED."
|
||||
#elif ENABLED(COREXZ) && ENABLED(Z_LATE_ENABLE)
|
||||
#error "Z_LATE_ENABLE can't be used with COREXZ."
|
||||
#elif defined(X_HOME_RETRACT_MM)
|
||||
#error "[XYZ]_HOME_RETRACT_MM settings have been renamed [XYZ]_HOME_BUMP_MM."
|
||||
#elif defined(BEEPER)
|
||||
#error "BEEPER is now BEEPER_PIN. Please update your pins definitions."
|
||||
#elif defined(SDCARDDETECT)
|
||||
#error "SDCARDDETECT is now SD_DETECT_PIN. Please update your pins definitions."
|
||||
#elif defined(SDCARDDETECTINVERTED)
|
||||
#error "SDCARDDETECTINVERTED is now SD_DETECT_INVERTED. Please update your configuration."
|
||||
#elif defined(BTENABLED)
|
||||
#error "BTENABLED is now BLUETOOTH. Please update your configuration."
|
||||
#elif defined(CUSTOM_MENDEL_NAME)
|
||||
#error "CUSTOM_MENDEL_NAME is now CUSTOM_MACHINE_NAME. Please update your configuration."
|
||||
#elif defined(HAS_AUTOMATIC_VERSIONING)
|
||||
#error "HAS_AUTOMATIC_VERSIONING is now USE_AUTOMATIC_VERSIONING. Please update your configuration."
|
||||
#elif defined(ENABLE_AUTO_BED_LEVELING)
|
||||
#error "ENABLE_AUTO_BED_LEVELING is now AUTO_BED_LEVELING_FEATURE. Please update your configuration."
|
||||
#elif defined(SDSLOW)
|
||||
#error "SDSLOW deprecated. Set SPI_SPEED to SPI_HALF_SPEED instead."
|
||||
#elif defined(SDEXTRASLOW)
|
||||
#error "SDEXTRASLOW deprecated. Set SPI_SPEED to SPI_QUARTER_SPEED instead."
|
||||
#elif defined(Z_RAISE_BEFORE_HOMING)
|
||||
#error "Z_RAISE_BEFORE_HOMING is deprecated. Use MIN_Z_HEIGHT_FOR_HOMING instead."
|
||||
#elif defined(FILAMENT_SENSOR)
|
||||
#error "FILAMENT_SENSOR is deprecated. Use FILAMENT_WIDTH_SENSOR instead."
|
||||
#elif defined(DISABLE_MAX_ENDSTOPS) || defined(DISABLE_MIN_ENDSTOPS)
|
||||
#error "DISABLE_MAX_ENDSTOPS and DISABLE_MIN_ENDSTOPS deprecated. Use individual USE_*_PLUG options instead."
|
||||
#elif ENABLED(Z_DUAL_ENDSTOPS) && !defined(Z2_USE_ENDSTOP)
|
||||
#error "Z_DUAL_ENDSTOPS settings are simplified. Just set Z2_USE_ENDSTOP to the endstop you want to repurpose for Z2"
|
||||
#elif defined(LANGUAGE_INCLUDE)
|
||||
#error "LANGUAGE_INCLUDE has been replaced by LCD_LANGUAGE. Please update your configuration."
|
||||
#elif defined(EXTRUDER_OFFSET_X) || defined(EXTRUDER_OFFSET_Y)
|
||||
#error "EXTRUDER_OFFSET_[XY] is deprecated. Use HOTEND_OFFSET_[XY] instead."
|
||||
#elif defined(PID_PARAMS_PER_EXTRUDER)
|
||||
#error "PID_PARAMS_PER_EXTRUDER is deprecated. Use PID_PARAMS_PER_HOTEND instead."
|
||||
#elif defined(EXTRUDER_WATTS)
|
||||
#error "EXTRUDER_WATTS is deprecated. Use HOTEND_WATTS instead."
|
||||
#elif defined(SERVO_ENDSTOP_ANGLES)
|
||||
#error "SERVO_ENDSTOP_ANGLES is deprecated. Use Z_SERVO_ANGLES instead."
|
||||
#elif defined(X_ENDSTOP_SERVO_NR) || defined(Y_ENDSTOP_SERVO_NR)
|
||||
#error "X_ENDSTOP_SERVO_NR and Y_ENDSTOP_SERVO_NR are deprecated and should be removed."
|
||||
#elif defined(XY_TRAVEL_SPEED)
|
||||
#error "XY_TRAVEL_SPEED is deprecated. Use XY_PROBE_SPEED instead."
|
||||
#elif defined(PROBE_SERVO_DEACTIVATION_DELAY)
|
||||
#error "PROBE_SERVO_DEACTIVATION_DELAY is deprecated. Use DEACTIVATE_SERVOS_AFTER_MOVE instead."
|
||||
#elif defined(SERVO_DEACTIVATION_DELAY)
|
||||
#error "SERVO_DEACTIVATION_DELAY is deprecated. Use SERVO_DELAY instead."
|
||||
#elif ENABLED(FILAMENTCHANGEENABLE)
|
||||
#error "FILAMENTCHANGEENABLE is now FILAMENT_CHANGE_FEATURE. Please update your configuration."
|
||||
#elif defined(PLA_PREHEAT_HOTEND_TEMP)
|
||||
#error "PLA_PREHEAT_HOTEND_TEMP is now PREHEAT_1_TEMP_HOTEND. Please update your configuration."
|
||||
#elif defined(PLA_PREHEAT_HPB_TEMP)
|
||||
#error "PLA_PREHEAT_HPB_TEMP is now PREHEAT_1_TEMP_BED. Please update your configuration."
|
||||
#elif defined(PLA_PREHEAT_FAN_SPEED)
|
||||
#error "PLA_PREHEAT_FAN_SPEED is now PREHEAT_1_FAN_SPEED. Please update your configuration."
|
||||
#elif defined(ABS_PREHEAT_HOTEND_TEMP)
|
||||
#error "ABS_PREHEAT_HOTEND_TEMP is now PREHEAT_2_TEMP_HOTEND. Please update your configuration."
|
||||
#elif defined(ABS_PREHEAT_HPB_TEMP)
|
||||
#error "ABS_PREHEAT_HPB_TEMP is now PREHEAT_2_TEMP_BED. Please update your configuration."
|
||||
#elif defined(ABS_PREHEAT_FAN_SPEED)
|
||||
#error "ABS_PREHEAT_FAN_SPEED is now PREHEAT_2_FAN_SPEED. Please update your configuration."
|
||||
#elif defined(ENDSTOPS_ONLY_FOR_HOMING)
|
||||
#error "ENDSTOPS_ONLY_FOR_HOMING is deprecated. Use (disable) ENDSTOPS_ALWAYS_ON_DEFAULT instead."
|
||||
#elif defined(HOMING_FEEDRATE)
|
||||
#error "HOMING_FEEDRATE is deprecated. Set individual rates with HOMING_FEEDRATE_(XY|Z|E) instead."
|
||||
#endif
|
||||
Loading…
Reference in new issue