diff --git a/Marlin/configuration_store.cpp b/Marlin/configuration_store.cpp index ea81b0c72..79d23b000 100644 --- a/Marlin/configuration_store.cpp +++ b/Marlin/configuration_store.cpp @@ -36,88 +36,89 @@ * */ -#define EEPROM_VERSION "V23" +#define EEPROM_VERSION "V24" /** - * V23 EEPROM Layout: + * V24 EEPROM Layout: * * 100 Version (char x4) + * 104 EEPROM Checksum (uint16_t) * - * 104 M92 XYZE planner.axis_steps_per_mm (float x4) - * 120 M203 XYZE planner.max_feedrate (float x4) - * 136 M201 XYZE planner.max_acceleration_mm_per_s2 (uint32_t x4) - * 152 M204 P planner.acceleration (float) - * 156 M204 R planner.retract_acceleration (float) - * 160 M204 T planner.travel_acceleration (float) - * 164 M205 S planner.min_feedrate (float) - * 168 M205 T planner.min_travel_feedrate (float) - * 172 M205 B planner.min_segment_time (ulong) - * 176 M205 X planner.max_xy_jerk (float) - * 180 M205 Z planner.max_z_jerk (float) - * 184 M205 E planner.max_e_jerk (float) - * 188 M206 XYZ home_offset (float x3) + * 106 M92 XYZE planner.axis_steps_per_mm (float x4) + * 122 M203 XYZE planner.max_feedrate (float x4) + * 138 M201 XYZE planner.max_acceleration_mm_per_s2 (uint32_t x4) + * 154 M204 P planner.acceleration (float) + * 158 M204 R planner.retract_acceleration (float) + * 162 M204 T planner.travel_acceleration (float) + * 166 M205 S planner.min_feedrate (float) + * 170 M205 T planner.min_travel_feedrate (float) + * 174 M205 B planner.min_segment_time (ulong) + * 178 M205 X planner.max_xy_jerk (float) + * 182 M205 Z planner.max_z_jerk (float) + * 186 M205 E planner.max_e_jerk (float) + * 190 M206 XYZ home_offset (float x3) * * Mesh bed leveling: - * 200 M420 S status (uint8) - * 201 z_offset (float) - * 205 mesh_num_x (uint8 as set in firmware) - * 206 mesh_num_y (uint8 as set in firmware) - * 207 G29 S3 XYZ z_values[][] (float x9, by default) + * 202 M420 S status (uint8) + * 203 z_offset (float) + * 207 mesh_num_x (uint8 as set in firmware) + * 208 mesh_num_y (uint8 as set in firmware) + * 209 G29 S3 XYZ z_values[][] (float x9, by default) * * AUTO BED LEVELING - * 243 M851 zprobe_zoffset (float) + * 245 M851 zprobe_zoffset (float) * * DELTA: - * 247 M666 XYZ endstop_adj (float x3) - * 259 M665 R delta_radius (float) - * 263 M665 L delta_diagonal_rod (float) - * 267 M665 S delta_segments_per_second (float) - * 271 M665 A delta_diagonal_rod_trim_tower_1 (float) - * 275 M665 B delta_diagonal_rod_trim_tower_2 (float) - * 279 M665 C delta_diagonal_rod_trim_tower_3 (float) + * 249 M666 XYZ endstop_adj (float x3) + * 261 M665 R delta_radius (float) + * 265 M665 L delta_diagonal_rod (float) + * 269 M665 S delta_segments_per_second (float) + * 273 M665 A delta_diagonal_rod_trim_tower_1 (float) + * 277 M665 B delta_diagonal_rod_trim_tower_2 (float) + * 281 M665 C delta_diagonal_rod_trim_tower_3 (float) * * Z_DUAL_ENDSTOPS: - * 283 M666 Z z_endstop_adj (float) + * 285 M666 Z z_endstop_adj (float) * * ULTIPANEL: - * 287 M145 S0 H plaPreheatHotendTemp (int) - * 289 M145 S0 B plaPreheatHPBTemp (int) - * 291 M145 S0 F plaPreheatFanSpeed (int) - * 293 M145 S1 H absPreheatHotendTemp (int) - * 295 M145 S1 B absPreheatHPBTemp (int) - * 297 M145 S1 F absPreheatFanSpeed (int) + * 289 M145 S0 H plaPreheatHotendTemp (int) + * 291 M145 S0 B plaPreheatHPBTemp (int) + * 293 M145 S0 F plaPreheatFanSpeed (int) + * 295 M145 S1 H absPreheatHotendTemp (int) + * 297 M145 S1 B absPreheatHPBTemp (int) + * 299 M145 S1 F absPreheatFanSpeed (int) * * PIDTEMP: - * 299 M301 E0 PIDC Kp[0], Ki[0], Kd[0], Kc[0] (float x4) - * 315 M301 E1 PIDC Kp[1], Ki[1], Kd[1], Kc[1] (float x4) - * 331 M301 E2 PIDC Kp[2], Ki[2], Kd[2], Kc[2] (float x4) - * 347 M301 E3 PIDC Kp[3], Ki[3], Kd[3], Kc[3] (float x4) - * 363 M301 L lpq_len (int) + * 301 M301 E0 PIDC Kp[0], Ki[0], Kd[0], Kc[0] (float x4) + * 317 M301 E1 PIDC Kp[1], Ki[1], Kd[1], Kc[1] (float x4) + * 333 M301 E2 PIDC Kp[2], Ki[2], Kd[2], Kc[2] (float x4) + * 349 M301 E3 PIDC Kp[3], Ki[3], Kd[3], Kc[3] (float x4) + * 365 M301 L lpq_len (int) * * PIDTEMPBED: - * 365 M304 PID thermalManager.bedKp, thermalManager.bedKi, thermalManager.bedKd (float x3) + * 367 M304 PID thermalManager.bedKp, thermalManager.bedKi, thermalManager.bedKd (float x3) * * DOGLCD: - * 377 M250 C lcd_contrast (int) + * 379 M250 C lcd_contrast (int) * * SCARA: - * 379 M365 XYZ axis_scaling (float x3) + * 381 M365 XYZ axis_scaling (float x3) * * FWRETRACT: - * 391 M209 S autoretract_enabled (bool) - * 392 M207 S retract_length (float) - * 396 M207 W retract_length_swap (float) - * 400 M207 F retract_feedrate_mm_s (float) - * 404 M207 Z retract_zlift (float) - * 408 M208 S retract_recover_length (float) - * 412 M208 W retract_recover_length_swap (float) - * 416 M208 F retract_recover_feedrate (float) + * 393 M209 S autoretract_enabled (bool) + * 394 M207 S retract_length (float) + * 398 M207 W retract_length_swap (float) + * 402 M207 F retract_feedrate_mm_s (float) + * 406 M207 Z retract_zlift (float) + * 410 M208 S retract_recover_length (float) + * 414 M208 W retract_recover_length_swap (float) + * 418 M208 F retract_recover_feedrate (float) * * Volumetric Extrusion: - * 420 M200 D volumetric_enabled (bool) - * 421 M200 T D filament_size (float x4) (T0..3) + * 422 M200 D volumetric_enabled (bool) + * 423 M200 T D filament_size (float x4) (T0..3) * - * 437 This Slot is Available! + * 439 This Slot is Available! * */ #include "Marlin.h" @@ -131,6 +132,9 @@ #include "mesh_bed_leveling.h" #endif +uint16_t eeprom_checksum; +const char version[4] = EEPROM_VERSION; + void _EEPROM_writeData(int &pos, uint8_t* value, uint8_t size) { uint8_t c; while (size--) { @@ -140,13 +144,16 @@ void _EEPROM_writeData(int &pos, uint8_t* value, uint8_t size) { SERIAL_ECHO_START; SERIAL_ECHOLNPGM(MSG_ERR_EEPROM_WRITE); } + eeprom_checksum += c; pos++; value++; }; } void _EEPROM_readData(int &pos, uint8_t* value, uint8_t size) { do { - *value = eeprom_read_byte((unsigned char*)pos); + uint8_t c = eeprom_read_byte((unsigned char*)pos); + *value = c; + eeprom_checksum += c; pos++; value++; } while (--size); @@ -172,7 +179,12 @@ void Config_StoreSettings() { float dummy = 0.0f; char ver[4] = "000"; int i = EEPROM_OFFSET; - EEPROM_WRITE_VAR(i, ver); // invalidate data first + + EEPROM_WRITE_VAR(i, ver); // invalidate data first + i += sizeof(eeprom_checksum); // Skip the checksum slot + + eeprom_checksum = 0; // clear before first "real data" + EEPROM_WRITE_VAR(i, planner.axis_steps_per_mm); EEPROM_WRITE_VAR(i, planner.max_feedrate); EEPROM_WRITE_VAR(i, planner.max_acceleration_mm_per_s2); @@ -324,9 +336,11 @@ void Config_StoreSettings() { EEPROM_WRITE_VAR(i, dummy); } - char ver2[4] = EEPROM_VERSION; + uint16_t final_checksum = eeprom_checksum; + int j = EEPROM_OFFSET; - EEPROM_WRITE_VAR(j, ver2); // validate data + EEPROM_WRITE_VAR(j, version); + EEPROM_WRITE_VAR(j, final_checksum); // Report storage size SERIAL_ECHO_START; @@ -342,18 +356,21 @@ void Config_RetrieveSettings() { int i = EEPROM_OFFSET; char stored_ver[4]; - char ver[4] = EEPROM_VERSION; - EEPROM_READ_VAR(i, stored_ver); //read stored version + uint16_t stored_checksum; + EEPROM_READ_VAR(i, stored_ver); + EEPROM_READ_VAR(i, stored_checksum); // SERIAL_ECHOPAIR("Version: [", ver); // SERIAL_ECHOPAIR("] Stored version: [", stored_ver); // SERIAL_ECHOLNPGM("]"); - if (strncmp(ver, stored_ver, 3) != 0) { + if (strncmp(version, stored_ver, 3) != 0) { Config_ResetDefault(); } else { float dummy = 0; + eeprom_checksum = 0; // clear before reading first "real data" + // version number match EEPROM_READ_VAR(i, planner.axis_steps_per_mm); EEPROM_READ_VAR(i, planner.max_feedrate); @@ -506,12 +523,19 @@ void Config_RetrieveSettings() { // Call thermalManager.updatePID (similar to when we have processed M301) thermalManager.updatePID(); - // Report settings retrieved and length - SERIAL_ECHO_START; - SERIAL_ECHO(ver); - SERIAL_ECHOPAIR(" stored settings retrieved (", i); - SERIAL_ECHOLNPGM(" bytes)"); - } + if (eeprom_checksum == stored_checksum) { + Config_Postprocess(); + SERIAL_ECHO_START; + SERIAL_ECHO(version); + SERIAL_ECHOPAIR(" stored settings retrieved (", i); + SERIAL_ECHOLNPGM(" bytes)"); + } + else { + SERIAL_ERROR_START; + SERIAL_ERRORLNPGM("EEPROM checksum mismatch"); + Config_ResetDefault(); + } + } #if ENABLED(EEPROM_CHITCHAT) Config_PrintSettings();