@ -309,6 +309,7 @@ your extruder heater takes 2 minutes to hit the target on heating.
#define ENDSTOPPULLUP_XMIN
#define ENDSTOPPULLUP_YMIN
#define ENDSTOPPULLUP_ZMIN
#define ENDSTOPPULLUP_ZPROBE
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
constboolX_MIN_ENDSTOP_INVERTING=false;// set to true to invert the logic of the endstop.
@ -317,9 +318,15 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o
constboolX_MAX_ENDSTOP_INVERTING=false;// set to true to invert the logic of the endstop.
constboolY_MAX_ENDSTOP_INVERTING=false;// set to true to invert the logic of the endstop.
constboolZ_MAX_ENDSTOP_INVERTING=false;// set to true to invert the logic of the endstop.
constboolZ_PROBE_ENDSTOP_INVERTING=false;// set to true to invert the logic of the endstop.
//#define DISABLE_MAX_ENDSTOPS
//#define DISABLE_MIN_ENDSTOPS
// If you want to enable the Z Probe pin, but disable its use, uncomment the line below.
// This only affects a Z Probe Endstop if you have separate Z min endstop as well and have
// activated Z_PROBE_AND_ENDSTOP below. If you are using the Z Min endstop on your Z Probe,
// this has no effect.
//#define DISABLE_Z_PROBE_ENDSTOP
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
#define X_ENABLE_ON 0
@ -484,33 +491,17 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
#endif
// Z Probe and Z endstop support
// Seaparte concurrent Z Probe and Z min endstop support
// Added by Chris Roadfeldt 3-28-2015
// If you have a Z Probe in addition to endstop(s) for Z Homing, uncomment the #define Z_PROBE_AND_ENDSTOP line below and configure Z Probe settings.
// Only use this if you have both a Z PROBE and Z HOMING ENDSTOP(S). If you are using Z_SAFE_HOMING above, then you probably don't need this unless you want to make use of
// a non-default pin for your Z Probe.
// Note: It's expected that your Z Probe triggers in the direction towards your bed. If your Z Probe does not trigger when traveling towards you bed, it will trigger when it's moving
// away from the bed.
// #define Z_PROBE_AND_ENDSTOP
#ifdef Z_PROBE_AND_ENDSTOP
// As of 3-28-2015, there are NO Z Probe pins defined in any board config files.
// Z_PROBE_PIN is for the signal pin only. RAMPS 1.3/1.4 boards may be able to use the 5V, Ground and the D32 pin in the Aux 4 section of the RAMPS board for the signal.
// If you have a Z Probe in addition to a Z min endstop, uncomment the #define Z_PROBE_AND_ENDSTOP line below and configure Z Probe settings.
// Only use this if you have both a Z PROBE and Z Min ENDSTOP.
// Note: It's expected that your Z Probe triggers in the direction towards your bed.
// In order to use this, you must have a Z_PROBE_PIN defined in the pins.h file for your control board.
// RAMPS 1.3/1.4 boards may be able to use the 5V, Ground and the D32 pin in the Aux 4 section of the RAMPS board for the signal.
// The D32 pin in Aux 4 on RAMPS maps to the Arduino D32 pin. The Z_PROBE_PIN is setting the pin to use on the Arduino. Since the D32 pin on the RAMPS maps to D32 on Arduino, this works.
// D32 is currently selected in the RAMPS 1.3/1.4 pin file. Update the pins.h file for your control board to make use of this. Not doing so nullifies Z_PROBE_AND_ENDSTOP
// WARNING: Setting the wrong pin may have unexpected and disastrous outcomes. Use with caution and do your homework.
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
constboolZ_PROBE_ENDSTOP_INVERTING=false;// set to true to invert the logic of the endstop.
// The pullups are needed if you directly connect a mechanical endstop between the signal and ground pins.
#define ENDSTOPPULLUP_ZPROBE
// If you want to enable the Z Probe pin, but disable its use, uncomment the line below.
Chris Roadfeldt
9 years ago