forksand
/
marlin-lulzbot-laser
1
1
Fork 0
Code Issues Pull Requests Releases Wiki Activity

Save and restore feedrate in more places

Browse Source
master
Scott Lahteine 9 years ago
parent fe173c2bc6
commit 6fdd5ba246
1 changed files with 30 additions and 17 deletions
Show Stats Download Patch File Download Diff File

47
Marlin/Marlin_main.cpp
Unescape View File

@ -366,6 +366,8 @@ static uint8_t target_extruder;
float zprobe_zoffset = Z_PROBE_OFFSET_FROM_EXTRUDER;
#endif
#define PLANNER_XY_FEEDRATE() (min(planner.max_feedrate[X_AXIS], planner.max_feedrate[Y_AXIS]))
#if ENABLED(AUTO_BED_LEVELING_FEATURE)
int xy_probe_speed = XY_PROBE_SPEED;
bool bed_leveling_in_progress = false;
@ -373,7 +375,7 @@ static uint8_t target_extruder;
#elif defined(XY_PROBE_SPEED)
#define XY_PROBE_FEEDRATE XY_PROBE_SPEED
#else
#define XY_PROBE_FEEDRATE (min(planner.max_feedrate[X_AXIS], planner.max_feedrate[Y_AXIS]) * 60)
#define XY_PROBE_FEEDRATE (PLANNER_XY_FEEDRATE() * 60)
#endif
#if ENABLED(Z_DUAL_ENDSTOPS) && DISABLED(DELTA)
@ -1712,8 +1714,12 @@ static void clean_up_after_endstop_or_probe_move() {
if ((Z_HOME_DIR) < 0 && zprobe_zoffset < 0)
z_dest -= zprobe_zoffset;
if (z_dest > current_position[Z_AXIS])
if (z_dest > current_position[Z_AXIS]) {
float old_feedrate = feedrate;
feedrate = homing_feedrate[Z_AXIS];
do_blocking_move_to_z(z_dest);
feedrate = old_feedrate;
}
}
inline void raise_z_after_probing() {
@ -1766,19 +1772,24 @@ static void clean_up_after_endstop_or_probe_move() {
if (endstops.z_probe_enabled == !dock) return; // already docked/undocked?
float oldXpos = current_position[X_AXIS]; // save x position
float old_feedrate = feedrate;
if (dock) {
raise_z_after_probing(); // raise Z
// Dock sled a bit closer to ensure proper capturing
feedrate = XY_PROBE_FEEDRATE;
do_blocking_move_to_x(X_MAX_POS + SLED_DOCKING_OFFSET + offset - 1);
digitalWrite(SLED_PIN, LOW); // turn off magnet
}
else {
feedrate = XY_PROBE_FEEDRATE;
float z_loc = current_position[Z_AXIS];
if (z_loc < Z_RAISE_BEFORE_PROBING + 5) z_loc = Z_RAISE_BEFORE_PROBING;
do_blocking_move_to(X_MAX_POS + SLED_DOCKING_OFFSET + offset, current_position[Y_AXIS], z_loc); // this also updates current_position
digitalWrite(SLED_PIN, HIGH); // turn on magnet
}
do_blocking_move_to_x(oldXpos); // return to position before docking
feedrate = old_feedrate;
}
#endif // Z_PROBE_SLED
@ -2102,7 +2113,10 @@ static void clean_up_after_endstop_or_probe_move() {
}
#endif
float old_feedrate = feedrate;
// Move Z up to the z_before height, then move the Z probe to the given XY
feedrate = homing_feedrate[Z_AXIS];
do_blocking_move_to_z(z_before); // this also updates current_position
#if ENABLED(DEBUG_LEVELING_FEATURE)
@ -2114,6 +2128,7 @@ static void clean_up_after_endstop_or_probe_move() {
#endif
// this also updates current_position
feedrate = XY_PROBE_FEEDRATE;
do_blocking_move_to_xy(x - (X_PROBE_OFFSET_FROM_EXTRUDER), y - (Y_PROBE_OFFSET_FROM_EXTRUDER));
if (probe_action & ProbeDeploy) {
@ -2147,6 +2162,8 @@ static void clean_up_after_endstop_or_probe_move() {
if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("<<< probe_pt");
#endif
feedrate = old_feedrate;
return measured_z;
}
@ -3473,8 +3490,6 @@ inline void gcode_G28() {
// Deploy the probe. Servo will raise if needed.
deploy_z_probe();
feedrate = homing_feedrate[Z_AXIS];
bed_leveling_in_progress = true;
#if ENABLED(AUTO_BED_LEVELING_GRID)
@ -4227,7 +4242,7 @@ inline void gcode_M42() {
bool seen_L = code_seen('L');
uint8_t n_legs = seen_L ? code_value_byte() : 0;
if (n_legs < 0 || n_legs > 15) {
if (n_legs > 15) {
SERIAL_PROTOCOLPGM("?Number of legs in movement not plausible (0-15).\n");
return;
}
@ -4252,16 +4267,20 @@ inline void gcode_M42() {
planner.bed_level_matrix.set_to_identity();
#endif
if (Z_start_location < Z_RAISE_BEFORE_PROBING * 2.0)
setup_for_endstop_or_probe_move();
if (Z_start_location < Z_RAISE_BEFORE_PROBING * 2.0) {
feedrate = homing_feedrate[Z_AXIS];
do_blocking_move_to_z(Z_start_location);
}
feedrate = XY_PROBE_FEEDRATE;
do_blocking_move_to_xy(X_probe_location - (X_PROBE_OFFSET_FROM_EXTRUDER), Y_probe_location - (Y_PROBE_OFFSET_FROM_EXTRUDER));
/**
* OK, do the initial probe to get us close to the bed.
* Then retrace the right amount and use that in subsequent probes
*/
setup_for_endstop_or_probe_move();
// Height before each probe (except the first)
float z_between = home_offset[Z_AXIS] + (deploy_probe_for_each_reading ? Z_RAISE_BEFORE_PROBING : Z_RAISE_BETWEEN_PROBINGS);
@ -4399,6 +4418,7 @@ inline void gcode_M42() {
// Raise before the next loop for the legs,
// or do the final raise after the last probe
if (n_legs || last_probe) {
feedrate = homing_feedrate[Z_AXIS];
do_blocking_move_to_z(last_probe ? home_offset[Z_AXIS] + Z_RAISE_AFTER_PROBING : z_between);
if (!last_probe) delay(500);
}
@ -6551,15 +6571,8 @@ inline void gcode_T(uint8_t tmp_extruder) {
float next_feedrate = code_value_axis_units(X_AXIS);
if (next_feedrate > 0.0) stored_feedrate = feedrate = next_feedrate;
}
else {
feedrate =
#ifdef XY_PROBE_SPEED
XY_PROBE_SPEED
#else
min(planner.max_feedrate[X_AXIS], planner.max_feedrate[Y_AXIS]) * 60
#endif
;
}
else
feedrate = XY_PROBE_FEEDRATE;
if (tmp_extruder != active_extruder) {
bool no_move = code_seen('S') && code_value_bool();
@ -7668,7 +7681,7 @@ void mesh_buffer_line(float x, float y, float z, const float e, float feed_rate,
delayed_move_time = 0;
// unpark extruder: 1) raise, 2) move into starting XY position, 3) lower
planner.buffer_line(raised_parked_position[X_AXIS], raised_parked_position[Y_AXIS], raised_parked_position[Z_AXIS], current_position[E_AXIS], planner.max_feedrate[Z_AXIS], active_extruder);
planner.buffer_line(current_position[X_AXIS], current_position[Y_AXIS], raised_parked_position[Z_AXIS], current_position[E_AXIS], min(planner.max_feedrate[X_AXIS], planner.max_feedrate[Y_AXIS]), active_extruder);
planner.buffer_line(current_position[X_AXIS], current_position[Y_AXIS], raised_parked_position[Z_AXIS], current_position[E_AXIS], PLANNER_XY_FEEDRATE(), active_extruder);
planner.buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], planner.max_feedrate[Z_AXIS], active_extruder);
active_extruder_parked = false;
}

Write Preview
Loading…
Cancel
Save