diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 85fd38968..3dd8f6199 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -4,8 +4,8 @@ // This determines the communication speed of the printer -#define BAUDRATE 250000 -//#define BAUDRATE 115200 +//#define BAUDRATE 250000 +#define BAUDRATE 115200 //#define BAUDRATE 230400 #define EXTRUDERS 1 @@ -29,7 +29,7 @@ // Sanguinololu 1.2 and above = 62 // Ultimaker = 7, // Teensylu = 8 -#define MOTHERBOARD 7 +#define MOTHERBOARD 99 //=========================================================================== //=============================Thermal Settings ============================ @@ -44,36 +44,36 @@ // 6 is EPCOS 100k // 7 is 100k Honeywell thermistor 135-104LAG-J01 -//#define THERMISTORHEATER_0 3 +#define THERMISTORHEATER_0 1 //#define THERMISTORHEATER_1 1 //#define THERMISTORHEATER_2 1 -//#define HEATER_0_USES_THERMISTOR +#define HEATER_0_USES_THERMISTOR //#define HEATER_1_USES_THERMISTOR //#define HEATER_2_USES_THERMISTOR -#define HEATER_0_USES_AD595 +//#define HEATER_0_USES_AD595 //#define HEATER_1_USES_AD595 //#define HEATER_2_USES_AD595 // Select one of these only to define how the bed temp is read. -//#define THERMISTORBED 1 -//#define BED_USES_THERMISTOR +#define THERMISTORBED 1 +#define BED_USES_THERMISTOR //#define BED_LIMIT_SWITCHING #ifdef BED_LIMIT_SWITCHING #define BED_HYSTERESIS 2 //only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS #endif //#define BED_USES_AD595 -#define BED_CHECK_INTERVAL 5000 //ms +#define BED_CHECK_INTERVAL 1000 //ms //// Heating sanity check: // This waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature // If the temperature has not increased at the end of that period, the target temperature is set to zero. // It can be reset with another M104/M109 -//#define WATCHPERIOD 20000 //20 seconds +#define WATCHPERIOD 20000 //20 seconds // Actual temperature must be close to target for this long before M109 returns success -#define TEMP_RESIDENCY_TIME 30 // (seconds) +#define TEMP_RESIDENCY_TIME 50 // (seconds) #define TEMP_HYSTERESIS 3 // (C°) range of +/- temperatures considered "close" to the target one //// The minimal temperature defines the temperature below which the heater will not be enabled @@ -86,10 +86,10 @@ // When temperature exceeds max temp, your heater will be switched off. // This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // You should use MINTEMP for thermistor short/failure protection. -#define HEATER_0_MAXTEMP 275 +#define HEATER_0_MAXTEMP 325 //#define HEATER_1_MAXTEMP 275 //#define HEATER_2_MAXTEMP 275 -//#define BED_MAXTEMP 150 +#define BED_MAXTEMP 140 // Wait for Cooldown @@ -103,7 +103,7 @@ // PID settings: // Uncomment the following line to enable PID support. -#define PIDTEMP +//#define PIDTEMP #define PID_MAX 255 // limits current to nozzle; 255=full current #ifdef PIDTEMP //#define PID_DEBUG // Sends debug data to the serial port. @@ -167,7 +167,7 @@ // extruder run-out prevention. //if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded //#define EXTRUDER_RUNOUT_PREVENT -#define EXTRUDER_RUNOUT_MINTEMP 190 +#define EXTRUDER_RUNOUT_MINTEMP 160 #define EXTRUDER_RUNOUT_SECONDS 30. #define EXTRUDER_RUNOUT_ESTEPS 14. //mm filament #define EXTRUDER_RUNOUT_SPEED 1500. //extrusion speed @@ -209,8 +209,8 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th //#define INVERT_E*_DIR true // for direct drive extruder v9 set to true, for geared extruder set to false, used for all extruders #define INVERT_X_DIR true // for Mendel set to false, for Orca set to true -#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false -#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true +#define INVERT_Y_DIR true // for Mendel set to true, for Orca set to false +#define INVERT_Z_DIR false // for Mendel set to false, for Orca set to true #define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false @@ -223,18 +223,18 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th #define min_software_endstops true //If true, axis won't move to coordinates less than zero. #define max_software_endstops true //If true, axis won't move to coordinates greater than the defined lengths below. -#define X_MAX_LENGTH 205 -#define Y_MAX_LENGTH 205 -#define Z_MAX_LENGTH 200 +#define X_MAX_LENGTH 187 +#define Y_MAX_LENGTH 188 +#define Z_MAX_LENGTH 80 //// MOVEMENT SETTINGS #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E -#define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0} // set the homing speeds (mm/min) +#define HOMING_FEEDRATE {2400, 2400, 150, 0} // set the homing speeds (mm/min) //homing hits the endstop, then retracts by this distance, before it tries to slowly bump again: -#define X_HOME_RETRACT_MM 5 -#define Y_HOME_RETRACT_MM 5 -#define Z_HOME_RETRACT_MM 1 +#define X_HOME_RETRACT_MM 2 +#define Y_HOME_RETRACT_MM 2 +#define Z_HOME_RETRACT_MM 2 #define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially. #define AXIS_RELATIVE_MODES {false, false, false, false} @@ -243,11 +243,11 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th // default settings -#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200*8/3,760*1.1} // default steps per unit for ultimaker +#define DEFAULT_AXIS_STEPS_PER_UNIT {64,64,3200,110} // default steps per unit for ultimaker //#define DEFAULT_AXIS_STEPS_PER_UNIT {40, 40, 3333.92, 360} //sells mendel with v9 extruder //#define DEFAULT_AXIS_STEPS_PER_UNIT {80.3232, 80.8900, 2284.7651, 757.2218} // SAE Prusa w/ Wade extruder -#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 45} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot. +#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 1000} // (mm/sec) +#define DEFAULT_MAX_ACCELERATION {1200,1200,100,9000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot. #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves #define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts @@ -257,7 +257,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th // minimum time in microseconds that a movement needs to take if the buffer is emptied. Increase this number if you see blobs while printing high speed & high detail. It will slowdown on the detailed stuff. #define DEFAULT_MINSEGMENTTIME 20000 // Obsolete delete this -#define DEFAULT_XYJERK 20.0 // (mm/sec) +#define DEFAULT_XYJERK 12.0 // (mm/sec) #define DEFAULT_ZJERK 0.4 // (mm/sec) // If defined the movements slow down when the look ahead buffer is only half full @@ -278,7 +278,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. //define this to enable eeprom support -#define EEPROM_SETTINGS +//#define EEPROM_SETTINGS //to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out: // please keep turned on if you can. #define EEPROM_CHITCHAT @@ -316,9 +316,9 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th //LCD and SD support //#define ULTRA_LCD //general lcd support, also 16x2 -//#define SDSUPPORT // Enable SD Card Support in Hardware Console -#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers? -#define SD_FINISHED_RELEASECOMMAND "M84 X Y E" // no z because of layer shift. +#define SDSUPPORT // Enable SD Card Support in Hardware Console +#define SD_FINISHED_STEPPERRELEASE false //if sd support and the file is finished: disable steppers? +#define SD_FINISHED_RELEASECOMMAND "M81" // no z because of layer shift. //#define ULTIPANEL #ifdef ULTIPANEL @@ -358,7 +358,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th //this prevents dangerous Extruder moves, i.e. if the temperature is under the limit //can be software-disabled for whatever purposes by #define PREVENT_DANGEROUS_EXTRUDE -#define EXTRUDE_MINTEMP 190 +#define EXTRUDE_MINTEMP 150 #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances. const int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement diff --git a/Marlin/pins.h b/Marlin/pins.h index 28e349161..da573a423 100644 --- a/Marlin/pins.h +++ b/Marlin/pins.h @@ -1,6 +1,49 @@ #ifndef PINS_H #define PINS_H +#if MOTHERBOARD == 99 +#define KNOWN_BOARD 1 + +#define X_STEP_PIN 2 +#define X_DIR_PIN 3 +#define X_ENABLE_PIN -1 +#define X_MIN_PIN 16 +#define X_MAX_PIN -1 + +#define Y_STEP_PIN 5 +#define Y_DIR_PIN 6 +#define Y_ENABLE_PIN -1 +#define Y_MIN_PIN 67 +#define Y_MAX_PIN -1 + +#define Z_STEP_PIN 62 +#define Z_DIR_PIN 63 +#define Z_ENABLE_PIN -1 +#define Z_MIN_PIN 59 +#define Z_MAX_PIN -1 + +#define E0_STEP_PIN 65 +#define E0_DIR_PIN 66 +#define E0_ENABLE_PIN -1 + +#define SDPOWER -1 +#define SDSS 53 +#define LED_PIN -1 +#define FAN_PIN -1 +#define PS_ON_PIN 9 +#define KILL_PIN -1 + +#define HEATER_0_PIN 13 +#define HEATER_1_PIN -1 +#define HEATER_2_PIN -1 +#define TEMP_0_PIN 6 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! +#define TEMP_1_PIN -1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! +#define TEMP_2_PIN -1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! +#define HEATER_BED_PIN 4 +#define TEMP_BED_PIN 10 + +#endif /* 99 */ + /**************************************************************************************** * Arduino pin assignment *