From 848475a5b0ceac3f11e1c6b18a625c45278342c8 Mon Sep 17 00:00:00 2001 From: PxT Date: Mon, 12 Jan 2015 13:28:31 -0800 Subject: [PATCH] Update GCodes.md Sort Gcodes numerically, other minor formatting changes --- Documentation/GCodes.md | 20 ++++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) diff --git a/Documentation/GCodes.md b/Documentation/GCodes.md index dd582946e..9ad2a336a 100644 --- a/Documentation/GCodes.md +++ b/Documentation/GCodes.md @@ -10,7 +10,7 @@ * G10 - retract filament according to settings of M207 * G11 - retract recover filament according to settings of M208 * G28 - Home all Axis -* G29 - Detailed Z-Probe, probes the bed at 3 points. You must de at the home position for this to work correctly. +* G29 - Detailed Z-Probe, probes the bed at 3 points. You must be at the home position for this to work correctly. * G30 - Single Z Probe, probes bed at current XY location. * G31 - Dock Z Probe sled (if enabled) * G32 - Undock Z Probe sled (if enabled) @@ -68,36 +68,36 @@ * M203 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec * M204 - Set default acceleration: S normal moves T filament only moves (M204 S3000 T7000) im mm/sec^2 also sets minimum segment time in ms (B20000) to prevent buffer underruns and M20 minimum feedrate * M205 - advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk, E=maximum E jerk -* M206 - set additional homeing offset +* M206 - set additional homing offset * M207 - set retract length S[positive mm] F[feedrate mm/min] Z[additional zlift/hop], stays in mm regardless of M200 setting * M208 - set recover=unretract length S[positive mm surplus to the M207 S*] F[feedrate mm/min] * M209 - S<1=true/0=false> enable automatic retract detect if the slicer did not support G10/11: every normal extrude-only move will be classified as retract depending on the direction. * M218 - set hotend offset (in mm): T X Y -* M220 S- set speed factor override percentage -* M221 S- set extrude factor override percentage +* M220 - S[factor in percent] - set speed factor override percentage +* M221 - S[factor in percent] - set extrude factor override percentage * M240 - Trigger a camera to take a photograph * M280 - Position an RC Servo P S, ommit S to report back current angle -* M300 - Play beepsound S P +* M300 - Play beep sound S P * M301 - Set PID parameters P I and D * M302 - Allow cold extrudes * M303 - PID relay autotune S sets the target temperature. (default target temperature = 150C) * M304 - Set bed PID parameters P I and D +* M350 - Set microstepping mode. +* M351 - Toggle MS1 MS2 pins directly. * M400 - Finish all moves * M401 - Lower z-probe if present * M402 - Raise z-probe if present -* M404 - N Enter the nominal filament width (3mm, 1.75mm ) or will display nominal filament width without parameters -* M405 - Turn on Filament Sensor extrusion control. Optional D to set delay in centimeters between sensor and extruder +* M404 - N Enter the nominal filament width (3mm, 1.75mm) or will display nominal filament width without parameters +* M405 - Turn on Filament Sensor extrusion control. Optional D[delay in cm] to set delay in centimeters between sensor and extruder * M406 - Turn off Filament Sensor extrusion control * M407 - Displays measured filament diameter * M500 - stores paramters in EEPROM * M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). * M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. -* M503 - print the current settings (from memory not from eeprom) +* M503 - print the current settings (from memory not from EEPROM) * M540 - Use S[0|1] to enable or disable the stop SD card print on endstop hit (requires ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED) * M600 - Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal] * M907 - Set digital trimpot motor current using axis codes. * M908 - Control digital trimpot directly. -* M350 - Set microstepping mode. -* M351 - Toggle MS1 MS2 pins directly. * M928 - Start SD logging (M928 filename.g) - ended by M29 * M999 - Restart after being stopped by error