diff --git a/Marlin/Conditionals.h b/Marlin/Conditionals.h
index 599a1bf24..2e6e55e44 100644
--- a/Marlin/Conditionals.h
+++ b/Marlin/Conditionals.h
@@ -732,7 +732,7 @@
       #define Z_ENDSTOP_SERVO_NR -1
     #endif
     #if X_ENDSTOP_SERVO_NR >= 0 || Y_ENDSTOP_SERVO_NR >= 0 || HAS_Z_ENDSTOP_SERVO
-      #define HAS_SERVO_ENDSTOPS true
+      #define HAS_SERVO_ENDSTOPS
       #define SERVO_ENDSTOP_IDS { X_ENDSTOP_SERVO_NR, Y_ENDSTOP_SERVO_NR, Z_ENDSTOP_SERVO_NR }
     #endif
   #endif
diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index b67d0a02f..968fca659 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -440,6 +440,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Probe Raise options provide clearance for the probe to deploy and stow.
+// For G28 these apply when the probe deploys and stows.
+// For G29 these apply before and after the full procedure.
+#define Z_RAISE_BEFORE_PROBING 15   // Raise before probe deploy (e.g., the first probe).
+#define Z_RAISE_AFTER_PROBING 15    // Raise before probe stow (e.g., the last probe).
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -585,7 +591,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
     #define ABL_PROBE_PT_3_X 170
     #define ABL_PROBE_PT_3_Y 20
 
-  #endif // AUTO_BED_LEVELING_GRID
+  #endif // !AUTO_BED_LEVELING_GRID
 
   // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
   // X and Y offsets must be integers.
@@ -610,9 +616,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
-  #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
-  #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
   //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
                                                                              // Useful to retract a deployable Z probe.
diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp
index 1feb42d7a..9d8005c9b 100644
--- a/Marlin/Marlin_main.cpp
+++ b/Marlin/Marlin_main.cpp
@@ -372,7 +372,7 @@ static uint8_t target_extruder;
   };
 #endif
 
-#if HAS_SERVO_ENDSTOPS
+#if ENABLED(HAS_SERVO_ENDSTOPS)
   const int servo_endstop_id[] = SERVO_ENDSTOP_IDS;
   const int servo_endstop_angle[][2] = SERVO_ENDSTOP_ANGLES;
 #endif
@@ -724,7 +724,7 @@ void servo_init() {
     servo[3].detach();
   #endif
 
-   #if HAS_SERVO_ENDSTOPS
+   #if ENABLED(HAS_SERVO_ENDSTOPS)
 
     endstops.enable_z_probe(false);
 
@@ -1701,7 +1701,12 @@ static void setup_for_endstop_move() {
   }
 
   inline void raise_z_after_probing() {
-    do_blocking_move_to_z(current_position[Z_AXIS] + Z_RAISE_AFTER_PROBING);
+    #if Z_RAISE_AFTER_PROBING > 0
+      #if ENABLED(DEBUG_LEVELING_FEATURE)
+        if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("raise_z_after_probing()");
+      #endif
+      do_blocking_move_to_z(current_position[Z_AXIS] + Z_RAISE_AFTER_PROBING);
+    #endif
   }
 
   static void clean_up_after_endstop_move() {
@@ -1724,7 +1729,7 @@ static void setup_for_endstop_move() {
 
     if (endstops.z_probe_enabled) return;
 
-    #if HAS_SERVO_ENDSTOPS
+    #if ENABLED(HAS_SERVO_ENDSTOPS)
 
       // Engage Z Servo endstop if enabled
       if (servo_endstop_id[Z_AXIS] >= 0) servo[servo_endstop_id[Z_AXIS]].move(servo_endstop_angle[Z_AXIS][0]);
@@ -1811,7 +1816,7 @@ static void setup_for_endstop_move() {
   }
 
   static void stow_z_probe(bool doRaise = true) {
-    #if !(HAS_SERVO_ENDSTOPS && (Z_RAISE_AFTER_PROBING > 0))
+    #if !(ENABLED(HAS_SERVO_ENDSTOPS) && (Z_RAISE_AFTER_PROBING > 0))
       UNUSED(doRaise);
     #endif
     #if ENABLED(DEBUG_LEVELING_FEATURE)
@@ -1820,21 +1825,13 @@ static void setup_for_endstop_move() {
 
     if (!endstops.z_probe_enabled) return;
 
-    #if HAS_SERVO_ENDSTOPS
+    #if ENABLED(HAS_SERVO_ENDSTOPS)
 
       // Retract Z Servo endstop if enabled
       if (servo_endstop_id[Z_AXIS] >= 0) {
 
         #if Z_RAISE_AFTER_PROBING > 0
           if (doRaise) {
-            #if ENABLED(DEBUG_LEVELING_FEATURE)
-              if (DEBUGGING(LEVELING)) {
-                SERIAL_ECHOPAIR("Raise Z (after) by ", Z_RAISE_AFTER_PROBING);
-                SERIAL_EOL;
-                SERIAL_ECHO("> SERVO_ENDSTOPS > raise_z_after_probing()");
-                SERIAL_EOL;
-              }
-            #endif
             raise_z_after_probing(); // this also updates current_position
             stepper.synchronize();
           }
@@ -2062,7 +2059,7 @@ static void setup_for_endstop_move() {
 
   #endif // DELTA
 
-  #if HAS_SERVO_ENDSTOPS && DISABLED(Z_PROBE_SLED)
+  #if ENABLED(HAS_SERVO_ENDSTOPS) && DISABLED(Z_PROBE_SLED)
 
     void raise_z_for_servo() {
       float zpos = current_position[Z_AXIS], z_dest = Z_RAISE_BEFORE_PROBING;
@@ -2122,9 +2119,7 @@ static void setup_for_endstop_move() {
 
     float oldXpos = current_position[X_AXIS]; // save x position
     if (dock) {
-      #if Z_RAISE_AFTER_PROBING > 0
-        raise_z_after_probing(); // raise Z
-      #endif
+      raise_z_after_probing(); // raise Z
       // Dock sled a bit closer to ensure proper capturing
       do_blocking_move_to_x(X_MAX_POS + SLED_DOCKING_OFFSET + offset - 1);
       digitalWrite(SLED_PIN, LOW); // turn off magnet
@@ -2173,33 +2168,36 @@ static void homeaxis(AxisEnum axis) {
     sync_plan_position();
 
     #if ENABLED(Z_PROBE_SLED)
-      #define _Z_SERVO_TEST       (axis != Z_AXIS)      // deploy Z, servo.move XY
-      #define _Z_PROBE_SUBTEST    false                 // Z will never be invoked
+      #define _Z_SERVO_TEST       (axis != Z_AXIS)      // already deployed Z
+      #define _Z_SERVO_SUBTEST    false                 // Z will never be invoked
       #define _Z_DEPLOY           (dock_sled(false))
       #define _Z_STOW             (dock_sled(true))
     #elif SERVO_LEVELING || ENABLED(FIX_MOUNTED_PROBE)
-      #define _Z_SERVO_TEST       (axis != Z_AXIS)      // servo.move XY
-      #define _Z_PROBE_SUBTEST    false                 // Z will never be invoked
+      #define _Z_SERVO_TEST       (axis != Z_AXIS)      // already deployed Z
+      #define _Z_SERVO_SUBTEST    false                 // Z will never be invoked
       #define _Z_DEPLOY           (deploy_z_probe())
       #define _Z_STOW             (stow_z_probe())
-    #elif HAS_SERVO_ENDSTOPS
-      #define _Z_SERVO_TEST       true                  // servo.move X, Y, Z
-      #define _Z_PROBE_SUBTEST    (axis == Z_AXIS)      // Z is a probe
+    #elif ENABLED(HAS_SERVO_ENDSTOPS)
+      #define _Z_SERVO_TEST       true                  // Z not deployed yet
+      #define _Z_SERVO_SUBTEST    (axis == Z_AXIS)      // Z is a probe
     #endif
 
-    if (axis == Z_AXIS) {
-      // If there's a Z probe that needs deployment...
-      #if ENABLED(Z_PROBE_SLED) || SERVO_LEVELING || ENABLED(FIX_MOUNTED_PROBE)
-        // ...and homing Z towards the bed? Deploy it.
-        if (axis_home_dir < 0) _Z_DEPLOY;
-      #endif
-    }
+    // If there's a Z probe that needs deployment...
+    #if ENABLED(Z_PROBE_SLED) || SERVO_LEVELING || ENABLED(FIX_MOUNTED_PROBE)
+      // ...and homing Z towards the bed? Deploy it.
+      if (axis == Z_AXIS && axis_home_dir < 0) {
+        #if ENABLED(DEBUG_LEVELING_FEATURE)
+          if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("> SERVO_LEVELING > " STRINGIFY(_Z_DEPLOY));
+        #endif
+        _Z_DEPLOY;
+      }
+    #endif
 
-    #if HAS_SERVO_ENDSTOPS
-      // Engage an X or Y Servo endstop if enabled
+    #if ENABLED(HAS_SERVO_ENDSTOPS)
+      // Engage an X, Y (or Z) Servo endstop if enabled
       if (_Z_SERVO_TEST && servo_endstop_id[axis] >= 0) {
         servo[servo_endstop_id[axis]].move(servo_endstop_angle[axis][0]);
-        if (_Z_PROBE_SUBTEST) endstops.z_probe_enabled = true;
+        if (_Z_SERVO_SUBTEST) endstops.z_probe_enabled = true;
       }
     #endif
 
@@ -2316,7 +2314,7 @@ static void homeaxis(AxisEnum axis) {
     axis_known_position[axis] = true;
     axis_homed[axis] = true;
 
-    // Put away the Z probe
+    // Put away the Z probe with a function
     #if ENABLED(Z_PROBE_SLED) || SERVO_LEVELING || ENABLED(FIX_MOUNTED_PROBE)
       if (axis == Z_AXIS && axis_home_dir < 0) {
         #if ENABLED(DEBUG_LEVELING_FEATURE)
@@ -2326,16 +2324,32 @@ static void homeaxis(AxisEnum axis) {
       }
     #endif
 
-    // Retract Servo endstop if enabled
-    #if HAS_SERVO_ENDSTOPS
+    // Retract X, Y (or Z) Servo endstop if enabled
+    #if ENABLED(HAS_SERVO_ENDSTOPS)
       if (_Z_SERVO_TEST && servo_endstop_id[axis] >= 0) {
+        // Raise the servo probe before stow outside ABL context.
+        // This is a workaround to allow use of a Servo Probe without
+        // ABL until more global probe handling is implemented.
+        #if Z_RAISE_AFTER_PROBING > 0
+          if (axis == Z_AXIS) {
+            #if ENABLED(DEBUG_LEVELING_FEATURE)
+              if (DEBUGGING(LEVELING)) SERIAL_ECHOPAIR("Raise Z (after) by ", Z_RAISE_AFTER_PROBING);
+            #endif
+            current_position[Z_AXIS] = Z_RAISE_AFTER_PROBING;
+            feedrate = homing_feedrate[Z_AXIS];
+            line_to_current_position();
+            stepper.synchronize();
+          }
+        #endif
+
         #if ENABLED(DEBUG_LEVELING_FEATURE)
           if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("> SERVO_ENDSTOPS > Stow with servo.move()");
         #endif
         servo[servo_endstop_id[axis]].move(servo_endstop_angle[axis][1]);
-        if (_Z_PROBE_SUBTEST) endstops.enable_z_probe(false);
+        if (_Z_SERVO_SUBTEST) endstops.enable_z_probe(false);
       }
-    #endif
+
+    #endif // HAS_SERVO_ENDSTOPS
 
   }
 
@@ -3564,7 +3578,7 @@ inline void gcode_G28() {
       // Allen Key Probe for Delta
       #if ENABLED(Z_PROBE_ALLEN_KEY) || SERVO_LEVELING
         stow_z_probe();
-      #elif Z_RAISE_AFTER_PROBING > 0
+      #else
         raise_z_after_probing(); // for non Allen Key probes, such as simple mechanical probe
       #endif
     #else // !DELTA
@@ -3624,7 +3638,7 @@ inline void gcode_G28() {
         #endif
 
         current_position[Z_AXIS] = -zprobe_zoffset + (z_tmp - real_z)
-          #if HAS_SERVO_ENDSTOPS || ENABLED(Z_PROBE_ALLEN_KEY) || ENABLED(Z_PROBE_SLED)
+          #if ENABLED(HAS_SERVO_ENDSTOPS) || ENABLED(Z_PROBE_ALLEN_KEY) || ENABLED(Z_PROBE_SLED)
              + Z_RAISE_AFTER_PROBING
           #endif
           ;
@@ -3639,9 +3653,9 @@ inline void gcode_G28() {
       // Sled assembly for Cartesian bots
       #if ENABLED(Z_PROBE_SLED)
         dock_sled(true); // dock the sled
-      #elif Z_RAISE_AFTER_PROBING > 0
+      #else
         // Raise Z axis for non-delta and non servo based probes
-        #if !defined(HAS_SERVO_ENDSTOPS) && DISABLED(Z_PROBE_ALLEN_KEY) && DISABLED(Z_PROBE_SLED)
+        #if DISABLED(HAS_SERVO_ENDSTOPS) && DISABLED(Z_PROBE_ALLEN_KEY) && DISABLED(Z_PROBE_SLED)
           raise_z_after_probing();
         #endif
       #endif
@@ -3685,7 +3699,7 @@ inline void gcode_G28() {
      * G30: Do a single Z probe at the current XY
      */
     inline void gcode_G30() {
-      #if HAS_SERVO_ENDSTOPS
+      #if ENABLED(HAS_SERVO_ENDSTOPS)
         raise_z_for_servo();
       #endif
       deploy_z_probe(); // Engage Z Servo endstop if available. Z_PROBE_SLED is missed here.
@@ -3707,7 +3721,7 @@ inline void gcode_G28() {
 
       clean_up_after_endstop_move(); // Too early. must be done after the stowing.
 
-      #if HAS_SERVO_ENDSTOPS
+      #if ENABLED(HAS_SERVO_ENDSTOPS)
         raise_z_for_servo();
       #endif
       stow_z_probe(false); // Retract Z Servo endstop if available. Z_PROBE_SLED is missed here.
@@ -5816,13 +5830,13 @@ inline void gcode_M303() {
  */
 inline void gcode_M400() { stepper.synchronize(); }
 
-#if ENABLED(AUTO_BED_LEVELING_FEATURE) && DISABLED(Z_PROBE_SLED) && (HAS_SERVO_ENDSTOPS || ENABLED(Z_PROBE_ALLEN_KEY))
+#if ENABLED(AUTO_BED_LEVELING_FEATURE) && DISABLED(Z_PROBE_SLED) && (ENABLED(HAS_SERVO_ENDSTOPS) || ENABLED(Z_PROBE_ALLEN_KEY))
 
   /**
    * M401: Engage Z Servo endstop if available
    */
   inline void gcode_M401() {
-    #if HAS_SERVO_ENDSTOPS
+    #if ENABLED(HAS_SERVO_ENDSTOPS)
       raise_z_for_servo();
     #endif
     deploy_z_probe();
@@ -5832,13 +5846,13 @@ inline void gcode_M400() { stepper.synchronize(); }
    * M402: Retract Z Servo endstop if enabled
    */
   inline void gcode_M402() {
-    #if HAS_SERVO_ENDSTOPS
+    #if ENABLED(HAS_SERVO_ENDSTOPS)
       raise_z_for_servo();
     #endif
     stow_z_probe(false);
   }
 
-#endif // AUTO_BED_LEVELING_FEATURE && (HAS_SERVO_ENDSTOPS || Z_PROBE_ALLEN_KEY) && !Z_PROBE_SLED
+#endif // AUTO_BED_LEVELING_FEATURE && (ENABLED(HAS_SERVO_ENDSTOPS) || Z_PROBE_ALLEN_KEY) && !Z_PROBE_SLED
 
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
 
@@ -7054,14 +7068,14 @@ void process_next_command() {
         gcode_M400();
         break;
 
-      #if ENABLED(AUTO_BED_LEVELING_FEATURE) && (HAS_SERVO_ENDSTOPS || ENABLED(Z_PROBE_ALLEN_KEY)) && DISABLED(Z_PROBE_SLED)
+      #if ENABLED(AUTO_BED_LEVELING_FEATURE) && (ENABLED(HAS_SERVO_ENDSTOPS) || ENABLED(Z_PROBE_ALLEN_KEY)) && DISABLED(Z_PROBE_SLED)
         case 401:
           gcode_M401();
           break;
         case 402:
           gcode_M402();
           break;
-      #endif // AUTO_BED_LEVELING_FEATURE && (HAS_SERVO_ENDSTOPS || Z_PROBE_ALLEN_KEY) && !Z_PROBE_SLED
+      #endif // AUTO_BED_LEVELING_FEATURE && (ENABLED(HAS_SERVO_ENDSTOPS) || Z_PROBE_ALLEN_KEY) && !Z_PROBE_SLED
 
       #if ENABLED(FILAMENT_WIDTH_SENSOR)
         case 404:  //M404 Enter the nominal filament width (3mm, 1.75mm ) N<3.0> or display nominal filament width
diff --git a/Marlin/SanityCheck.h b/Marlin/SanityCheck.h
index 3fa6788a7..d2c53be14 100644
--- a/Marlin/SanityCheck.h
+++ b/Marlin/SanityCheck.h
@@ -174,7 +174,7 @@
 /**
  * Servo deactivation depends on servo endstops
  */
-#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE) && !HAS_SERVO_ENDSTOPS
+#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE) && DISABLED(HAS_SERVO_ENDSTOPS)
   #error "At least one of the ?_ENDSTOP_SERVO_NR is required for DEACTIVATE_SERVOS_AFTER_MOVE."
 #endif
 
diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h
index 39e5ce4e3..55b806140 100644
--- a/Marlin/example_configurations/Felix/Configuration.h
+++ b/Marlin/example_configurations/Felix/Configuration.h
@@ -422,6 +422,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Probe Raise options provide clearance for the probe to deploy and stow.
+// For G28 these apply when the probe deploys and stows.
+// For G29 these apply before and after the full procedure.
+#define Z_RAISE_BEFORE_PROBING 15   // Raise before probe deploy (e.g., the first probe).
+#define Z_RAISE_AFTER_PROBING 15    // Raise before probe stow (e.g., the last probe).
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -567,7 +573,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
     #define ABL_PROBE_PT_3_X 170
     #define ABL_PROBE_PT_3_Y 20
 
-  #endif // AUTO_BED_LEVELING_GRID
+  #endif // !AUTO_BED_LEVELING_GRID
 
   // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
   // X and Y offsets must be integers.
@@ -592,9 +598,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
-  #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
-  #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
   //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
                                                                              // Useful to retract a deployable Z probe.
diff --git a/Marlin/example_configurations/Felix/DUAL/Configuration.h b/Marlin/example_configurations/Felix/DUAL/Configuration.h
index 107f8386c..cebc6794f 100644
--- a/Marlin/example_configurations/Felix/DUAL/Configuration.h
+++ b/Marlin/example_configurations/Felix/DUAL/Configuration.h
@@ -420,6 +420,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Probe Raise options provide clearance for the probe to deploy and stow.
+// For G28 these apply when the probe deploys and stows.
+// For G29 these apply before and after the full procedure.
+#define Z_RAISE_BEFORE_PROBING 15   // Raise before probe deploy (e.g., the first probe).
+#define Z_RAISE_AFTER_PROBING 15    // Raise before probe stow (e.g., the last probe).
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -565,7 +571,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
     #define ABL_PROBE_PT_3_X 170
     #define ABL_PROBE_PT_3_Y 20
 
-  #endif // AUTO_BED_LEVELING_GRID
+  #endif // !AUTO_BED_LEVELING_GRID
 
   // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
   // X and Y offsets must be integers.
@@ -590,9 +596,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
-  #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
-  #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
   //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
                                                                              // Useful to retract a deployable Z probe.
diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h
index 5b41fb397..e2dd327e0 100644
--- a/Marlin/example_configurations/Hephestos/Configuration.h
+++ b/Marlin/example_configurations/Hephestos/Configuration.h
@@ -432,6 +432,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Probe Raise options provide clearance for the probe to deploy and stow.
+// For G28 these apply when the probe deploys and stows.
+// For G29 these apply before and after the full procedure.
+#define Z_RAISE_BEFORE_PROBING 15   // Raise before probe deploy (e.g., the first probe).
+#define Z_RAISE_AFTER_PROBING 15    // Raise before probe stow (e.g., the last probe).
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -577,7 +583,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
     #define ABL_PROBE_PT_3_X 170
     #define ABL_PROBE_PT_3_Y 20
 
-  #endif // AUTO_BED_LEVELING_GRID
+  #endif // !AUTO_BED_LEVELING_GRID
 
   // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
   // X and Y offsets must be integers.
@@ -602,9 +608,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
-  #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
-  #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
   //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
                                                                              // Useful to retract a deployable Z probe.
diff --git a/Marlin/example_configurations/Hephestos_2/Configuration.h b/Marlin/example_configurations/Hephestos_2/Configuration.h
index 3f6f4b644..1ea120af9 100644
--- a/Marlin/example_configurations/Hephestos_2/Configuration.h
+++ b/Marlin/example_configurations/Hephestos_2/Configuration.h
@@ -434,6 +434,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Probe Raise options provide clearance for the probe to deploy and stow.
+// For G28 these apply when the probe deploys and stows.
+// For G29 these apply before and after the full procedure.
+#define Z_RAISE_BEFORE_PROBING 5    // Raise before probe deploy (e.g., the first probe).
+#define Z_RAISE_AFTER_PROBING 5     // Raise before probe stow (e.g., the last probe).
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -579,7 +585,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
     #define ABL_PROBE_PT_3_X ((X_MIN_POS + X_MAX_POS) / 2)
     #define ABL_PROBE_PT_3_Y Y_MAX_POS - (Y_PROBE_OFFSET_FROM_EXTRUDER)
 
-  #endif // AUTO_BED_LEVELING_GRID
+  #endif // !AUTO_BED_LEVELING_GRID
 
   // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
   // X and Y offsets must be integers.
@@ -604,9 +610,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
-  #define Z_RAISE_BEFORE_PROBING   5  // How much the Z axis will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 2  // How much the Z axis will be raised when traveling from between next probing points.
-  #define Z_RAISE_AFTER_PROBING    5  // How much the Z axis will be raised after the last probing point.
 
   //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
                                                                              // Useful to retract a deployable Z probe.
diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h
index 4b74fe505..ada26986f 100644
--- a/Marlin/example_configurations/K8200/Configuration.h
+++ b/Marlin/example_configurations/K8200/Configuration.h
@@ -457,6 +457,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Probe Raise options provide clearance for the probe to deploy and stow.
+// For G28 these apply when the probe deploys and stows.
+// For G29 these apply before and after the full procedure.
+#define Z_RAISE_BEFORE_PROBING 15   // Raise before probe deploy (e.g., the first probe).
+#define Z_RAISE_AFTER_PROBING 15    // Raise before probe stow (e.g., the last probe).
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -602,7 +608,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
     #define ABL_PROBE_PT_3_X 170
     #define ABL_PROBE_PT_3_Y 20
 
-  #endif // AUTO_BED_LEVELING_GRID
+  #endif // !AUTO_BED_LEVELING_GRID
 
   // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
   // X and Y offsets must be integers.
@@ -627,9 +633,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
-  #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
-  #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
   //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
                                                                              // Useful to retract a deployable Z probe.
diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
index d9c8b9be4..3df2b7bd0 100644
--- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
+++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
@@ -440,6 +440,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Probe Raise options provide clearance for the probe to deploy and stow.
+// For G28 these apply when the probe deploys and stows.
+// For G29 these apply before and after the full procedure.
+#define Z_RAISE_BEFORE_PROBING 15   // Raise before probe deploy (e.g., the first probe).
+#define Z_RAISE_AFTER_PROBING 15    // Raise before probe stow (e.g., the last probe).
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -585,7 +591,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
     #define ABL_PROBE_PT_3_X 170
     #define ABL_PROBE_PT_3_Y 20
 
-  #endif // AUTO_BED_LEVELING_GRID
+  #endif // !AUTO_BED_LEVELING_GRID
 
   // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
   // X and Y offsets must be integers.
@@ -610,9 +616,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
-  #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
-  #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
   //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
                                                                              // Useful to retract a deployable Z probe.
diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h
index 967927d86..d153fa9dd 100644
--- a/Marlin/example_configurations/RigidBot/Configuration.h
+++ b/Marlin/example_configurations/RigidBot/Configuration.h
@@ -434,6 +434,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Probe Raise options provide clearance for the probe to deploy and stow.
+// For G28 these apply when the probe deploys and stows.
+// For G29 these apply before and after the full procedure.
+#define Z_RAISE_BEFORE_PROBING 15   // Raise before probe deploy (e.g., the first probe).
+#define Z_RAISE_AFTER_PROBING 15    // Raise before probe stow (e.g., the last probe).
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -579,7 +585,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
     #define ABL_PROBE_PT_3_X 170
     #define ABL_PROBE_PT_3_Y 20
 
-  #endif // AUTO_BED_LEVELING_GRID
+  #endif // !AUTO_BED_LEVELING_GRID
 
   // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
   // X and Y offsets must be integers.
@@ -604,9 +610,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
-  #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
-  #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
   //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
                                                                              // Useful to retract a deployable Z probe.
diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h
index a801823ee..1b28aae80 100644
--- a/Marlin/example_configurations/SCARA/Configuration.h
+++ b/Marlin/example_configurations/SCARA/Configuration.h
@@ -448,6 +448,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Probe Raise options provide clearance for the probe to deploy and stow.
+// For G28 these apply when the probe deploys and stows.
+// For G29 these apply before and after the full procedure.
+#define Z_RAISE_BEFORE_PROBING 15   // Raise before probe deploy (e.g., the first probe).
+#define Z_RAISE_AFTER_PROBING 15    // Raise before probe stow (e.g., the last probe).
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -593,7 +599,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
     #define ABL_PROBE_PT_3_X 170
     #define ABL_PROBE_PT_3_Y 20
 
-  #endif // AUTO_BED_LEVELING_GRID
+  #endif // !AUTO_BED_LEVELING_GRID
 
   // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
   // X and Y offsets must be integers.
@@ -618,9 +624,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
-  #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
-  #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
   //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
                                                                              // Useful to retract a deployable Z probe.
diff --git a/Marlin/example_configurations/TAZ4/Configuration.h b/Marlin/example_configurations/TAZ4/Configuration.h
index b2bd2ce8a..a0197907b 100644
--- a/Marlin/example_configurations/TAZ4/Configuration.h
+++ b/Marlin/example_configurations/TAZ4/Configuration.h
@@ -461,6 +461,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Probe Raise options provide clearance for the probe to deploy and stow.
+// For G28 these apply when the probe deploys and stows.
+// For G29 these apply before and after the full procedure.
+#define Z_RAISE_BEFORE_PROBING 15   // Raise before probe deploy (e.g., the first probe).
+#define Z_RAISE_AFTER_PROBING 15    // Raise before probe stow (e.g., the last probe).
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -606,7 +612,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
     #define ABL_PROBE_PT_3_X 170
     #define ABL_PROBE_PT_3_Y 20
 
-  #endif // AUTO_BED_LEVELING_GRID
+  #endif // !AUTO_BED_LEVELING_GRID
 
   // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
   // X and Y offsets must be integers.
@@ -631,9 +637,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
-  #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
-  #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
   //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
                                                                              // Useful to retract a deployable Z probe.
diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h
index f32e071d1..cdd075c83 100644
--- a/Marlin/example_configurations/WITBOX/Configuration.h
+++ b/Marlin/example_configurations/WITBOX/Configuration.h
@@ -432,6 +432,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Probe Raise options provide clearance for the probe to deploy and stow.
+// For G28 these apply when the probe deploys and stows.
+// For G29 these apply before and after the full procedure.
+#define Z_RAISE_BEFORE_PROBING 15   // Raise before probe deploy (e.g., the first probe).
+#define Z_RAISE_AFTER_PROBING 15    // Raise before probe stow (e.g., the last probe).
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -577,7 +583,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
     #define ABL_PROBE_PT_3_X 170
     #define ABL_PROBE_PT_3_Y 20
 
-  #endif // AUTO_BED_LEVELING_GRID
+  #endif // !AUTO_BED_LEVELING_GRID
 
   // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
   // X and Y offsets must be integers.
@@ -602,9 +608,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
-  #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
-  #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
   //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
                                                                              // Useful to retract a deployable Z probe.
diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
index 151e16bc8..7a5d012d6 100644
--- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h
+++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
@@ -440,6 +440,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Probe Raise options provide clearance for the probe to deploy and stow.
+// For G28 these apply when the probe deploys and stows.
+// For G29 these apply before and after the full procedure.
+#define Z_RAISE_BEFORE_PROBING 15   // Raise before probe deploy (e.g., the first probe).
+#define Z_RAISE_AFTER_PROBING 15    // Raise before probe stow (e.g., the last probe).
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -585,7 +591,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
     #define ABL_PROBE_PT_3_X 170
     #define ABL_PROBE_PT_3_Y 20
 
-  #endif // AUTO_BED_LEVELING_GRID
+  #endif // !AUTO_BED_LEVELING_GRID
 
   // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
   // X and Y offsets must be integers.
@@ -610,9 +616,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
-  #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
-  #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
   //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
                                                                              // Useful to retract a deployable Z probe.
diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration.h b/Marlin/example_configurations/delta/biv2.5/Configuration.h
index 026a72733..739af6ece 100644
--- a/Marlin/example_configurations/delta/biv2.5/Configuration.h
+++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h
@@ -482,6 +482,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Probe Raise options provide clearance for the probe to deploy and stow.
+// For G28 these apply when the probe deploys and stows.
+// For G29 these apply before and after the full procedure.
+#define Z_RAISE_BEFORE_PROBING 15   // Raise before probe deploy (e.g., the first probe).
+#define Z_RAISE_AFTER_PROBING 50    // Raise before probe stow (e.g., the last probe).
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -631,7 +637,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
     #define ABL_PROBE_PT_3_X 170
     #define ABL_PROBE_PT_3_Y 20
 
-  #endif // AUTO_BED_LEVELING_GRID
+  #endif // !AUTO_BED_LEVELING_GRID
 
   // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
   // X and Y offsets must be integers.
@@ -656,9 +662,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 
   #define XY_TRAVEL_SPEED 4000         // X and Y axis travel speed between probes, in mm/min.
 
-  #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
-  #define Z_RAISE_AFTER_PROBING 50    // How much the Z axis will be raised after the last probing point.
 
   //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
                                                                              // Useful to retract a deployable Z probe.
diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h
index dea1dfe83..714152c72 100644
--- a/Marlin/example_configurations/delta/generic/Configuration.h
+++ b/Marlin/example_configurations/delta/generic/Configuration.h
@@ -482,6 +482,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Probe Raise options provide clearance for the probe to deploy and stow.
+// For G28 these apply when the probe deploys and stows.
+// For G29 these apply before and after the full procedure.
+#define Z_RAISE_BEFORE_PROBING 15   // Raise before probe deploy (e.g., the first probe).
+#define Z_RAISE_AFTER_PROBING 50    // Raise before probe stow (e.g., the last probe).
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -631,7 +637,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
     #define ABL_PROBE_PT_3_X 170
     #define ABL_PROBE_PT_3_Y 20
 
-  #endif // AUTO_BED_LEVELING_GRID
+  #endif // !AUTO_BED_LEVELING_GRID
 
   // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
   // X and Y offsets must be integers.
@@ -656,9 +662,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 
   #define XY_TRAVEL_SPEED 4000         // X and Y axis travel speed between probes, in mm/min.
 
-  #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points
-  #define Z_RAISE_AFTER_PROBING 50    // How much the Z axis will be raised after the last probing point.
 
   //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
                                                                              // Useful to retract a deployable Z probe.
diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
index b26298913..e9e5c428a 100644
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
@@ -482,6 +482,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Probe Raise options provide clearance for the probe to deploy and stow.
+// For G28 these apply when the probe deploys and stows.
+// For G29 these apply before and after the full procedure.
+#define Z_RAISE_BEFORE_PROBING 15   // Raise before probe deploy (e.g., the first probe).
+#define Z_RAISE_AFTER_PROBING 50    // Raise before probe stow (e.g., the last probe).
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -631,7 +637,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
     #define ABL_PROBE_PT_3_X 170
     #define ABL_PROBE_PT_3_Y 20
 
-  #endif // AUTO_BED_LEVELING_GRID
+  #endif // !AUTO_BED_LEVELING_GRID
 
   // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
   // X and Y offsets must be integers.
@@ -656,9 +662,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
   #define XY_TRAVEL_SPEED 4000         // X and Y axis travel speed between probes, in mm/min.
 
-  #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points
-  #define Z_RAISE_AFTER_PROBING 50    // How much the Z axis will be raised after the last probing point.
 
   //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
                                                                              // Useful to retract a deployable Z probe.
diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
index d87239d1a..406edd16a 100644
--- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
@@ -471,6 +471,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Probe Raise options provide clearance for the probe to deploy and stow.
+// For G28 these apply when the probe deploys and stows.
+// For G29 these apply before and after the full procedure.
+#define Z_RAISE_BEFORE_PROBING 100  // Raise before probe deploy (e.g., the first probe).
+#define Z_RAISE_AFTER_PROBING 15    // Raise before probe stow (e.g., the last probe).
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -620,7 +626,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
     #define ABL_PROBE_PT_3_X 170
     #define ABL_PROBE_PT_3_Y 20
 
-  #endif // AUTO_BED_LEVELING_GRID
+  #endif // !AUTO_BED_LEVELING_GRID
 
   // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
   // X and Y offsets must be integers.
@@ -647,9 +653,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
-  #define Z_RAISE_BEFORE_PROBING 100  // How much the Z axis will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
-  #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
   //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
                                                                              // Useful to retract a deployable Z probe.
diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration.h b/Marlin/example_configurations/delta/kossel_xl/Configuration.h
index fa4e96d58..ab5403574 100644
--- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h
@@ -480,6 +480,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Probe Raise options provide clearance for the probe to deploy and stow.
+// For G28 these apply when the probe deploys and stows.
+// For G29 these apply before and after the full procedure.
+#define Z_RAISE_BEFORE_PROBING 20   // Raise before probe deploy (e.g., the first probe).
+#define Z_RAISE_AFTER_PROBING 20    // Raise before probe stow (e.g., the last probe).
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -629,7 +635,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
     #define ABL_PROBE_PT_3_X 170
     #define ABL_PROBE_PT_3_Y 20
 
-  #endif // AUTO_BED_LEVELING_GRID
+  #endif // !AUTO_BED_LEVELING_GRID
 
   // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
   // X and Y offsets must be integers.
@@ -654,9 +660,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
-  #define Z_RAISE_BEFORE_PROBING 20   // How much the Z axis will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 10 // How much the Z axis will be raised when traveling from between next probing points.
-  #define Z_RAISE_AFTER_PROBING 20    // How much the Z axis will be raised after the last probing point.
 
   //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
                                                                              // Useful to retract a deployable Z probe.
diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h
index 1991ee620..55696956d 100644
--- a/Marlin/example_configurations/makibox/Configuration.h
+++ b/Marlin/example_configurations/makibox/Configuration.h
@@ -443,6 +443,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Probe Raise options provide clearance for the probe to deploy and stow.
+// For G28 these apply when the probe deploys and stows.
+// For G29 these apply before and after the full procedure.
+#define Z_RAISE_BEFORE_PROBING 15   // Raise before probe deploy (e.g., the first probe).
+#define Z_RAISE_AFTER_PROBING 15    // Raise before probe stow (e.g., the last probe).
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -588,7 +594,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
     #define ABL_PROBE_PT_3_X 170
     #define ABL_PROBE_PT_3_Y 20
 
-  #endif // AUTO_BED_LEVELING_GRID
+  #endif // !AUTO_BED_LEVELING_GRID
 
   // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
   // X and Y offsets must be integers.
@@ -613,9 +619,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
-  #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
-  #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
   //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
                                                                              // Useful to retract a deployable Z probe.
diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
index c380ee2a0..fc52ac4cb 100644
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
@@ -430,6 +430,12 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Probe Raise options provide clearance for the probe to deploy and stow.
+// For G28 these apply when the probe deploys and stows.
+// For G29 these apply before and after the full procedure.
+#define Z_RAISE_BEFORE_PROBING 15   // Raise before probe deploy (e.g., the first probe).
+#define Z_RAISE_AFTER_PROBING 15    // Raise before probe stow (e.g., the last probe).
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 1
@@ -575,7 +581,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
     #define ABL_PROBE_PT_3_X 170
     #define ABL_PROBE_PT_3_Y 20
 
-  #endif // AUTO_BED_LEVELING_GRID
+  #endif // !AUTO_BED_LEVELING_GRID
 
   // Z Probe to nozzle (X,Y) offset, relative to (0, 0).
   // X and Y offsets must be integers.
@@ -600,9 +606,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 
   #define XY_TRAVEL_SPEED 8000         // X and Y axis travel speed between probes, in mm/min.
 
-  #define Z_RAISE_BEFORE_PROBING 15   // How much the Z axis will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  // How much the Z axis will be raised when traveling from between next probing points.
-  #define Z_RAISE_AFTER_PROBING 15    // How much the Z axis will be raised after the last probing point.
 
   //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
                                                                              // Useful to retract a deployable Z probe.