diff --git a/Marlin/pins_5DPRINT.h b/Marlin/pins_5DPRINT.h old mode 100644 new mode 100755 index f44a56887..f56ec0b67 --- a/Marlin/pins_5DPRINT.h +++ b/Marlin/pins_5DPRINT.h @@ -1,6 +1,6 @@ /** * Marlin 3D Printer Firmware - * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm @@ -20,6 +20,47 @@ * */ +/** + * Rev B 2 JUN 2017 + * + * Converted to Arduino pin numbering + */ + +/** + * There are two Arduino IDE extensions that are compatible with this board + * and with the mainstream Marlin software. + * + * Teensyduino - http://www.pjrc.com/teensy/teensyduino.html + * Select Teensy++ 2.0 in Arduino IDE from the 'Tools -> Boards' menu + * + * Installation instructions are at the above URL. Don't bother loading the + * libraries - they are not used with the Marlin software. + * + * Printrboard - https://github.com/scwimbush/Printrboard-HID-Arduino-IDE-Support + * + * Installation: + * + * 1. Go to the above URL, click on the "Clone or Download" button and then + * click on "Download ZIP" button. + * 2. Unzip the file, find the "printrboard" directory and then copy it to the + * hardware directory in Arduino. The Arduino hardware directory will probably + * be located in a path similar to this: C:\Program Files (x86)\Arduino\hardware. + * 3. Restart Arduino. + * 4. Select "Printrboard" from the 'Tools -> Boards' menu. + * + * Teensyduino is the most popular option. Printrboard is used if your board doesn't have + * the Teensyduino bootloader on it. + */ + +/** + * To burn the bootloader that comes with Printrboard: + * + * 1. Connect your programmer to the board. + * 2. In the Arduino IDE select "Printrboard" and then select the programmer. + * 3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message. + * 4. The programmer is no longer needed. Remove it. + */ + /** * 5DPrint D8 Driver board pin assignments * @@ -27,7 +68,7 @@ */ #ifndef __AVR_AT90USB1286__ - #error "Oops! Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu." + #error "Oops! Make sure you have 'Teensy++ 2.0' or 'Printrboard' selected from the 'Tools -> Boards' menu." #endif #define DEFAULT_MACHINE_NAME "Makibox" @@ -39,56 +80,54 @@ // // Limit Switches // -#define X_STOP_PIN 37 -#define Y_STOP_PIN 36 -#define Z_STOP_PIN 39 +#define X_STOP_PIN 37 // E5 +#define Y_STOP_PIN 36 // E4 +#define Z_STOP_PIN 19 // E7 // // Steppers // -#define X_STEP_PIN 0 -#define X_DIR_PIN 1 -#define X_ENABLE_PIN 23 - -#define Y_STEP_PIN 2 -#define Y_DIR_PIN 3 -#define Y_ENABLE_PIN 19 - -#define Z_STEP_PIN 4 -#define Z_DIR_PIN 5 -#define Z_ENABLE_PIN 18 - -#define E0_STEP_PIN 6 -#define E0_DIR_PIN 7 -#define E0_ENABLE_PIN 17 - -// Microstepping pins - Mapping not from fastio.h (?) -#define X_MS1_PIN 25 -#define X_MS2_PIN 26 -#define Y_MS1_PIN 9 -#define Y_MS2_PIN 8 -#define Z_MS1_PIN 7 -#define Z_MS2_PIN 6 -#define E0_MS1_PIN 5 -#define E0_MS2_PIN 4 +#define X_STEP_PIN 28 // A0 +#define X_DIR_PIN 29 // A1 +#define X_ENABLE_PIN 17 // C7 + +#define Y_STEP_PIN 30 // A2 +#define Y_DIR_PIN 31 // A3 +#define Y_ENABLE_PIN 13 // C3 + +#define Z_STEP_PIN 32 // A4 +#define Z_DIR_PIN 33 // A5 +#define Z_ENABLE_PIN 12 // C2 + +#define E0_STEP_PIN 34 // A6 +#define E0_DIR_PIN 35 // A7 +#define E0_ENABLE_PIN 11 // C1 + + +#define X_MS1_PIN 25 // B5 +#define X_MS2_PIN 26 // B6 +#define Y_MS1_PIN 9 // E1 +#define Y_MS2_PIN 8 // E0 +#define Z_MS1_PIN 7 // D7 +#define Z_MS2_PIN 6 // D6 +#define E0_MS1_PIN 5 // D5 +#define E0_MS2_PIN 4 // D4 // // Temperature Sensors // -#define TEMP_0_PIN 1 // Analog Input -#define TEMP_BED_PIN 0 // Analog Input +#define TEMP_0_PIN 1 // F1 Analog Input +#define TEMP_BED_PIN 0 // F0 Analog Input // // Heaters / Fans // -#define HEATER_0_PIN 21 -#define HEATER_BED_PIN 20 +#define HEATER_0_PIN 15 // C5 +#define HEATER_BED_PIN 14 // C4 -// You may need to change FAN_PIN to 16 because Marlin isn't using fastio.h -// for the fan and Teensyduino uses a different pin mapping. -#define FAN_PIN 16 +#define FAN_PIN 16 // C6 PWM3A // // Misc. Functions // -#define SDSS 20 +#define SDSS 20 // B0 diff --git a/Marlin/pins_BRAINWAVE.h b/Marlin/pins_BRAINWAVE.h old mode 100644 new mode 100755 index 83e7a35a9..2776c5006 --- a/Marlin/pins_BRAINWAVE.h +++ b/Marlin/pins_BRAINWAVE.h @@ -1,6 +1,6 @@ /** * Marlin 3D Printer Firmware - * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm @@ -34,6 +34,12 @@ * allow this board to use the latest Marlin software */ +/** + * Rev C 2 JUN 2017 + * + * Converted to Arduino pin numbering + */ + /** * Marlin_AT90USB - https://github.com/Bob-the-Kuhn/Marlin_AT90USB * This is the only known IDE extension that is compatible with the pin definitions @@ -49,20 +55,20 @@ * https://rawgit.com/Bob-the-Kuhn/Marlin_AT90USB/master/package_MARLIN_AT90USB_index.json * 2. Under Tools -> Board -> Boards manager, scroll to the bottom, click on MARLIN_AT90USB * and then click on "Install" - * 3. Select "AT90USB646_STANDARD" from the 'Tools -> Boards' menu. + * 3. Select "AT90USB646_TEENSYPP" from the 'Tools -> Boards' menu. */ /** * To burn the bootloader that comes with Marlin_AT90USB: * * 1. Connect your programmer to the board. - * 2. In Arduino IDE select "AT90USB646_STANDARD" and then select the programmer. + * 2. In Arduino IDE select "AT90USB646_TEENSYPP" and then select the programmer. * 3. In Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message. * 4. The programmer is no longer needed. Remove it. */ #ifndef __AVR_AT90USB646__ - #error "Oops! Make sure you have 'Brainwave' selected from the 'Tools -> Boards' menu." + #error "Oops! Make sure you have 'AT90USB646_TEENSYPP' selected from the 'Tools -> Boards' menu." #endif #define BOARD_NAME "Brainwave" @@ -72,48 +78,48 @@ // // Limit Switches // -#define X_STOP_PIN 7 -#define Y_STOP_PIN 6 -#define Z_STOP_PIN 5 +#define X_STOP_PIN 35 // A7 +#define Y_STOP_PIN 34 // A6 +#define Z_STOP_PIN 33 // A5 // // Steppers // -#define X_STEP_PIN 27 -#define X_DIR_PIN 29 -#define X_ENABLE_PIN 28 -#define X_ATT_PIN 26 - -#define Y_STEP_PIN 31 -#define Y_DIR_PIN 33 -#define Y_ENABLE_PIN 32 -#define Y_ATT_PIN 30 - -#define Z_STEP_PIN 17 -#define Z_DIR_PIN 19 -#define Z_ENABLE_PIN 18 -#define Z_ATT_PIN 16 - -#define E0_STEP_PIN 21 -#define E0_DIR_PIN 23 -#define E0_ENABLE_PIN 22 -#define E0_ATT_PIN 20 +#define X_STEP_PIN 3 // D3 +#define X_DIR_PIN 5 // D5 +#define X_ENABLE_PIN 4 // D4 +#define X_ATT_PIN 2 // D2 + +#define Y_STEP_PIN 7 // D7 +#define Y_DIR_PIN 9 // E1 +#define Y_ENABLE_PIN 8 // E0 +#define Y_ATT_PIN 6 // D6 + +#define Z_STEP_PIN 11 // C1 +#define Z_DIR_PIN 13 // C3 +#define Z_ENABLE_PIN 12 // C2 +#define Z_ATT_PIN 10 // C0 + +#define E0_STEP_PIN 15 // C5 +#define E0_DIR_PIN 17 // C7 +#define E0_ENABLE_PIN 16 // C6 +#define E0_ATT_PIN 14 // C4 // // Temperature Sensors // -#define TEMP_0_PIN 7 // Analog Input -#define TEMP_BED_PIN 6 // Analog Input +#define TEMP_0_PIN 7 // F7 Analog Input +#define TEMP_BED_PIN 6 // F6 Analog Input // // Heaters / Fans // -#define HEATER_0_PIN 4 // Extruder -#define HEATER_BED_PIN 38 // Bed +#define HEATER_0_PIN 32 // A4 Extruder +#define HEATER_BED_PIN 18 // E6 Bed -#define FAN_PIN 3 // Fan +#define FAN_PIN 31 // A3 Fan // // Misc. Functions // -#define LED_PIN 39 +#define LED_PIN 19 // E7 diff --git a/Marlin/pins_BRAINWAVE_PRO.h b/Marlin/pins_BRAINWAVE_PRO.h old mode 100644 new mode 100755 index 02835ca27..ef780d579 --- a/Marlin/pins_BRAINWAVE_PRO.h +++ b/Marlin/pins_BRAINWAVE_PRO.h @@ -1,6 +1,6 @@ /** * Marlin 3D Printer Firmware - * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm @@ -32,11 +32,16 @@ * * Added pointers to currently available Arduino IDE extensions that will * allow this board to use the latest Marlin software + * + * + * Rev C 2 JUN 2017 + * + * Converted to Arduino pin numbering */ /** - * There are three Arduino IDE extensions that are compatible with this board - * and with the mainstream Marlin software. All have been used with Arduino 1.6.12 + * There are two Arduino IDE extensions that are compatible with this board + * and with the mainstream Marlin software. * * Teensyduino - http://www.pjrc.com/teensy/teensyduino.html * Select Teensy++ 2.0 in Arduino IDE from the 'Tools -> Boards' menu @@ -45,8 +50,6 @@ * libraries - they are not used with the Marlin software. * * Printrboard - https://github.com/scwimbush/Printrboard-HID-Arduino-IDE-Support - * This is basically Teensyduino but with a bootloader that can handle image sizes - * larger than 64K. * * Installation: * @@ -54,43 +57,25 @@ * click on "Download ZIP" button. * 2. Unzip the file, find the "printrboard" directory and then copy it to the * hardware directory in Arduino. The Arduino hardware directory will probably - * be located in a path similar to this: C:\Program Files (x86)\Arduino\hardware. + * be located in a path similar to this: C:\Program Files (x86)\Arduino\hardware. * 3. Restart Arduino. * 4. Select "Printrboard" from the 'Tools -> Boards' menu. * - * Marlin_AT90USB - https://github.com/Bob-the-Kuhn/Marlin_AT90USB - * Uses the bootloader from Printerboard above. - * - * "Marlin_AT90USB" makes PWM0A available rather than the usual PWM1C. These PWMs share - * the same physical pin. Marlin uses TIMER1 to generate interrupts and sets it up such - * that PWM1A, PWM1B & PWM1C can't be used. - * - * Installation: - * - * 1. In the Arduino IDE, under Files -> Preferences paste the following URL - * https://rawgit.com/Bob-the-Kuhn/Marlin_AT90USB/master/package_MARLIN_AT90USB_index.json - * 2. Under Tools -> Board -> Boards manager, scroll to the bottom, click on MARLIN_AT90USB - * and then click on "Install" - * 3. Select "AT90USB1286_TEENSYPP" from the 'Tools -> Boards' menu. + * Teensyduino is the most popular option. Printrboard is used if your board doesn't have + * the Teensyduino bootloader on it. */ /** - * To burn the bootloader that comes with Printrboard and Marlin_AT90USB: + * To burn the bootloader that comes with Printrboard: * * 1. Connect your programmer to the board. - * 2. In the Arduino IDE select "Printrboard" or "AT90USB1286_TEENSYPP" and then select the programmer. + * 2. In the Arduino IDE select "Printrboard" and then select the programmer. * 3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message. * 4. The programmer is no longer needed. Remove it. */ #ifndef __AVR_AT90USB1286__ - #error "Oops! Make sure you have 'Teensy++ 2.0', 'AT90USB1286_TEENSYPP', or 'Printrboard' selected from the 'Tools -> Boards' menu." -#endif - -#include "fastio.h" - -#if DISABLED(AT90USBxx_TEENSYPP_ASSIGNMENTS) // use Teensyduino Teensy++2.0 pin assignments instead of Marlin alphabetical. - #error "Uncomment '#define AT90USBxx_TEENSYPP_ASSIGNMENTS' in fastio.h for this config" + #error "Oops! Make sure you have 'Teensy++ 2.0' or 'Printrboard' selected from the 'Tools -> Boards' menu." #endif #define BOARD_NAME "Brainwave Pro" @@ -101,53 +86,53 @@ // // Limit Switches // -#define X_STOP_PIN 47 -#define Y_STOP_PIN 18 -#define Z_MAX_PIN 36 +#define X_STOP_PIN 45 // F7 +#define Y_STOP_PIN 12 // C2 +#define Z_STOP_PIN 36 // E4 // // Z Probe (when not Z_MIN_PIN) // #ifndef Z_MIN_PROBE_PIN - #define Z_MIN_PROBE_PIN 17 + #define Z_MIN_PROBE_PIN 11 // C1 #endif // // Steppers // -#define X_STEP_PIN 33 -#define X_DIR_PIN 32 -#define X_ENABLE_PIN 11 +#define X_STEP_PIN 9 // E1 +#define X_DIR_PIN 8 // E0 +#define X_ENABLE_PIN 23 // B3 -#define Y_STEP_PIN 31 -#define Y_DIR_PIN 30 -#define Y_ENABLE_PIN 8 +#define Y_STEP_PIN 7 // D7 +#define Y_DIR_PIN 6 // D6 +#define Y_ENABLE_PIN 20 // B0 -#define Z_STEP_PIN 29 -#define Z_DIR_PIN 28 -#define Z_ENABLE_PIN 37 +#define Z_STEP_PIN 5 // D5 +#define Z_DIR_PIN 4 // D4 +#define Z_ENABLE_PIN 37 // E5 -#define E0_STEP_PIN 35 -#define E0_DIR_PIN 34 -#define E0_ENABLE_PIN 13 +#define E0_STEP_PIN 47 // E3 +#define E0_DIR_PIN 46 // E2 +#define E0_ENABLE_PIN 25 // B5 // // Temperature Sensors // -#define TEMP_0_PIN 2 // Analog Input -#define TEMP_1_PIN 1 // Analog Input -#define TEMP_BED_PIN 0 // Analog Input +#define TEMP_0_PIN 2 // F2 Analog Input +#define TEMP_1_PIN 1 // F1 Analog Input +#define TEMP_BED_PIN 0 // F0 Analog Input // // Heaters / Fans // -#define HEATER_0_PIN 15 -#define HEATER_BED_PIN 14 // Bed -#define FAN_PIN 16 // Fan, PWM +#define HEATER_0_PIN 27 // B7 +#define HEATER_BED_PIN 26 // B6 Bed +#define FAN_PIN 16 // C6 Fan, PWM3A // // Misc. Functions // -#define SDSS 20 -#define SD_DETECT_PIN 12 -#define LED_PIN 19 +#define SDSS 20 // B0 +#define SD_DETECT_PIN 24 // B4 +#define LED_PIN 13 // C3 diff --git a/Marlin/pins_PRINTRBOARD.h b/Marlin/pins_PRINTRBOARD.h old mode 100644 new mode 100755 index a679340e7..7dec695d5 --- a/Marlin/pins_PRINTRBOARD.h +++ b/Marlin/pins_PRINTRBOARD.h @@ -1,6 +1,6 @@ /** * Marlin 3D Printer Firmware - * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm @@ -21,18 +21,48 @@ */ /** - * Printrboard pin assignments (AT90USB1286) - * Requires the Teensyduino software with Teensy++ 2.0 selected in Arduino IDE! - * http://www.pjrc.com/teensy/teensyduino.html - * See http://reprap.org/wiki/Printrboard for more info + * Rev B 2 JUN 2017 + * + * Converted to Arduino pin numbering */ -#ifndef __AVR_AT90USB1286__ - #error "Oops! Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu." -#endif +/** + * There are two Arduino IDE extensions that are compatible with this board + * and with the mainstream Marlin software. + * + * Teensyduino - http://www.pjrc.com/teensy/teensyduino.html + * Select Teensy++ 2.0 in Arduino IDE from the 'Tools -> Boards' menu + * + * Installation instructions are at the above URL. Don't bother loading the + * libraries - they are not used with the Marlin software. + * + * Printrboard - https://github.com/scwimbush/Printrboard-HID-Arduino-IDE-Support + * + * Installation: + * + * 1. Go to the above URL, click on the "Clone or Download" button and then + * click on "Download ZIP" button. + * 2. Unzip the file, find the "printrboard" directory and then copy it to the + * hardware directory in Arduino. The Arduino hardware directory will probably + * be located in a path similar to this: C:\Program Files (x86)\Arduino\hardware. + * 3. Restart Arduino. + * 4. Select "Printrboard" from the 'Tools -> Boards' menu. + * + * Teensyduino is the most popular option. Printrboard is used if your board doesn't have + * the Teensyduino bootloader on it. + */ -#if ENABLED(AT90USBxx_TEENSYPP_ASSIGNMENTS) // use Teensyduino Teensy++2.0 pin assignments instead of Marlin traditional. - #error "These Printrboard assignments depend on traditional Marlin assignments, not AT90USBxx_TEENSYPP_ASSIGNMENTS in fastio.h" +/** + * To burn the bootloader that comes with Printrboard: + * + * 1. Connect your programmer to the board. + * 2. In the Arduino IDE select "Printrboard" and then select the programmer. + * 3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message. + * 4. The programmer is no longer needed. Remove it. + */ + +#ifndef __AVR_AT90USB1286__ + #error "Oops! Make sure you have 'Teensy++ 2.0' or 'Printrboard' selected from the 'Tools -> Boards' menu." #endif #define BOARD_NAME "Printrboard" @@ -46,32 +76,32 @@ // // Limit Switches // -#define X_STOP_PIN 35 +#define X_STOP_PIN 47 // E3 #if ENABLED(SDSUPPORT) - #define Y_STOP_PIN 37 // Move Ystop to Estop socket + #define Y_STOP_PIN 37 // E5 - Move Ystop to Estop socket #else - #define Y_STOP_PIN 8 // Ystop in Ystop socket + #define Y_STOP_PIN 20 // B0 SS - Ystop in Ystop socket #endif -#define Z_STOP_PIN 36 +#define Z_STOP_PIN 36 // E4 // // Steppers // -#define X_STEP_PIN 0 -#define X_DIR_PIN 1 -#define X_ENABLE_PIN 39 +#define X_STEP_PIN 28 // A0 +#define X_DIR_PIN 29 // A1 +#define X_ENABLE_PIN 19 // E7 -#define Y_STEP_PIN 2 -#define Y_DIR_PIN 3 -#define Y_ENABLE_PIN 38 +#define Y_STEP_PIN 30 // A2 +#define Y_DIR_PIN 31 // A3 +#define Y_ENABLE_PIN 18 // E6 -#define Z_STEP_PIN 4 -#define Z_DIR_PIN 5 -#define Z_ENABLE_PIN 23 +#define Z_STEP_PIN 32 // A4 +#define Z_DIR_PIN 33 // A5 +#define Z_ENABLE_PIN 17 // C7 -#define E0_STEP_PIN 6 -#define E0_DIR_PIN 7 -#define E0_ENABLE_PIN 19 +#define E0_STEP_PIN 34 // A6 +#define E0_DIR_PIN 35 // A7 +#define E0_ENABLE_PIN 13 // C3 // // Temperature Sensors @@ -82,76 +112,67 @@ // // Heaters / Fans // -#define HEATER_0_PIN 21 // Extruder -#define HEATER_1_PIN 46 -#define HEATER_2_PIN 47 -#define HEATER_BED_PIN 20 - -// If soft or fast PWM is off then use Teensyduino pin numbering, Marlin -// fastio pin numbering otherwise -#if ENABLED(FAN_SOFT_PWM) || ENABLED(FAST_PWM_FAN) - #define FAN_PIN 22 -#else - #define FAN_PIN 16 -#endif +#define HEATER_0_PIN 15 // C5 PWM3B - Extruder +#define HEATER_1_PIN 44 // F6 +#define HEATER_2_PIN 45 // F7 +#define HEATER_BED_PIN 14 // C4 PWM3C + + +#define FAN_PIN 16 // C6 PWM3A // // Misc. Functions // -#define SDSS 26 - -#ifndef FILWIDTH_PIN - #define FILWIDTH_PIN 2 // Analog Input -#endif +#define SDSS 20 // B0 SS +#define FILWIDTH_PIN 2 // Analog Input // // LCD / Controller // #if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL) // we have no buzzer installed - #define BEEPER_PIN -1 + #define BEEPER_PIN -1 // LCD Pins #if ENABLED(LCD_I2C_PANELOLU2) - #define BTN_EN1 27 // RX1 - fastio.h pin mapping 27 - #define BTN_EN2 26 // TX1 - fastio.h pin mapping 26 - #define BTN_ENC 43 // A3 - fastio.h pin mapping 43 - #define SDSS 40 // use SD card on Panelolu2 (Teensyduino pin mapping) + #define BTN_EN1 3 // D3 RX1 JP2-7 + #define BTN_EN2 2 // D2 TX1 JP2-5 + #define BTN_ENC 41 // F3 JP2-4 + #define SDSS 38 // F0 B-THERM connector - use SD card on Panelolu2 #else - #define BTN_EN1 16 - #define BTN_EN2 17 - #define BTN_ENC 18 // the click - #endif // LCD_I2C_PANELOLU2 + #define BTN_EN1 10 // C0 JP11-12 + #define BTN_EN2 11 // C1 JP11-13 + #define BTN_ENC 12 // C2 JP11-14 + #endif - // not connected to a pin - #define SD_DETECT_PIN -1 + // not connected + #define SD_DETECT_PIN -1 - #define LCD_PINS_RS 9 - #define LCD_PINS_ENABLE 8 - #define LCD_PINS_D4 7 - #define LCD_PINS_D5 6 - #define LCD_PINS_D6 5 - #define LCD_PINS_D7 4 + #define LCD_PINS_RS 9 // E1 JP11-11 + #define LCD_PINS_ENABLE 8 // E0 JP11-10 + #define LCD_PINS_D4 7 // D7 JP11-8 + #define LCD_PINS_D5 6 // D6 JP11-7 + #define LCD_PINS_D6 5 // D5 JP11-6 + #define LCD_PINS_D7 4 // D4 JP11-5 #endif // ULTRA_LCD && NEWPANEL #if ENABLED(VIKI2) || ENABLED(miniVIKI) - // FastIO - #define BEEPER_PIN 32 + #define BEEPER_PIN 8 // E0 JP11-10 // Pins for DOGM SPI LCD Support - #define DOGLCD_A0 42 // Non-FastIO - #define DOGLCD_CS 43 // Non-FastIO + #define DOGLCD_A0 40 // F2 JP2-2 + #define DOGLCD_CS 41 // F3 JP2-4 #define LCD_SCREEN_ROT_180 - // The encoder and click button (FastIO Pins) - #define BTN_EN1 26 - #define BTN_EN2 27 - #define BTN_ENC 47 + // The encoder and click button + #define BTN_EN1 2 // D2 TX1 JP2-5 + #define BTN_EN2 3 // D3 RX1 JP2-7 + #define BTN_ENC 45 // F7 TDI JP2-12 - #define SDSS 45 - #define SD_DETECT_PIN -1 // FastIO (Manual says 72 I'm not certain cause I can't test) + #define SDSS 43 // F5 TMS JP2-8 + #define SD_DETECT_PIN -1 - #define STAT_LED_RED_PIN 12 // Non-FastIO - #define STAT_LED_BLUE_PIN 10 // Non-FastIO + #define STAT_LED_RED_PIN 12 // C2 JP11-14 + #define STAT_LED_BLUE_PIN 10 // C0 JP11-12 #endif diff --git a/Marlin/pins_PRINTRBOARD_REVF.h b/Marlin/pins_PRINTRBOARD_REVF.h old mode 100644 new mode 100755 index 16753fe32..f83bdf5ab --- a/Marlin/pins_PRINTRBOARD_REVF.h +++ b/Marlin/pins_PRINTRBOARD_REVF.h @@ -1,6 +1,6 @@ /** * Marlin 3D Printer Firmware - * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm @@ -21,18 +21,48 @@ */ /** - * Printrboard pin assignments (AT90USB1286) - * Requires the Teensyduino software with Teensy++ 2.0 selected in Arduino IDE! - * http://www.pjrc.com/teensy/teensyduino.html - * See http://reprap.org/wiki/Printrboard for more info + * Rev B 2 JUN 2017 + * + * Converted to Arduino pin numbering */ -#ifndef __AVR_AT90USB1286__ - #error "Oops! Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu." -#endif +/** + * There are two Arduino IDE extensions that are compatible with this board + * and with the mainstream Marlin software. + * + * Teensyduino - http://www.pjrc.com/teensy/teensyduino.html + * Select Teensy++ 2.0 in Arduino IDE from the 'Tools -> Boards' menu + * + * Installation instructions are at the above URL. Don't bother loading the + * libraries - they are not used with the Marlin software. + * + * Printrboard - https://github.com/scwimbush/Printrboard-HID-Arduino-IDE-Support + * + * Installation: + * + * 1. Go to the above URL, click on the "Clone or Download" button and then + * click on "Download ZIP" button. + * 2. Unzip the file, find the "printrboard" directory and then copy it to the + * hardware directory in Arduino. The Arduino hardware directory will probably + * be located in a path similar to this: C:\Program Files (x86)\Arduino\hardware. + * 3. Restart Arduino. + * 4. Select "Printrboard" from the 'Tools -> Boards' menu. + * + * Teensyduino is the most popular option. Printrboard is used if your board doesn't have + * the Teensyduino bootloader on it. + */ -#if ENABLED(AT90USBxx_TEENSYPP_ASSIGNMENTS) // use Teensyduino Teensy++2.0 pin assignments instead of Marlin traditional. - #error "These Printrboard assignments depend on traditional Marlin assignments, not AT90USBxx_TEENSYPP_ASSIGNMENTS in fastio.h" +/** + * To burn the bootloader that comes with Printrboard: + * + * 1. Connect your programmer to the board. + * 2. In the Arduino IDE select "Printrboard" and then select the programmer. + * 3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message. + * 4. The programmer is no longer needed. Remove it. + */ + +#ifndef __AVR_AT90USB1286__ + #error "Oops! Make sure you have 'Teensy++ 2.0' or 'Printrboard' selected from the 'Tools -> Boards' menu." #endif #define BOARD_NAME "Printrboard Rev F" @@ -41,28 +71,28 @@ // // Limit Switches // -#define X_STOP_PIN 35 -#define Y_STOP_PIN 12 -#define Z_STOP_PIN 36 +#define X_STOP_PIN 47 // E3 +#define Y_STOP_PIN 24 // B4 PWM2A +#define Z_STOP_PIN 36 // E4 // // Steppers // -#define X_STEP_PIN 0 -#define X_DIR_PIN 1 -#define X_ENABLE_PIN 39 +#define X_STEP_PIN 28 // A0 +#define X_DIR_PIN 29 // A1 +#define X_ENABLE_PIN 19 // E7 -#define Y_STEP_PIN 2 -#define Y_DIR_PIN 3 -#define Y_ENABLE_PIN 38 +#define Y_STEP_PIN 30 // A2 +#define Y_DIR_PIN 31 // A3 +#define Y_ENABLE_PIN 18 // E6 -#define Z_STEP_PIN 4 -#define Z_DIR_PIN 5 -#define Z_ENABLE_PIN 23 +#define Z_STEP_PIN 32 // A4 +#define Z_DIR_PIN 33 // A5 +#define Z_ENABLE_PIN 17 // C7 -#define E0_STEP_PIN 6 -#define E0_DIR_PIN 7 -#define E0_ENABLE_PIN 19 +#define E0_STEP_PIN 34 // A6 +#define E0_DIR_PIN 35 // A7 +#define E0_ENABLE_PIN 13 // C3 // uncomment to enable an I2C based DAC like on the Printrboard REVF #define DAC_STEPPER_CURRENT @@ -72,7 +102,7 @@ #define DAC_STEPPER_SENSE 0.11 #define DAC_STEPPER_ADDRESS 0 #define DAC_STEPPER_MAX 3520 -#define DAC_STEPPER_VREF 1 // internal Vref, gain 1x = 2.048V +#define DAC_STEPPER_VREF 1 // internal Vref, gain 1x = 2.048V #define DAC_STEPPER_GAIN 0 #define DAC_OR_ADDRESS 0x00 @@ -85,68 +115,52 @@ // // Heaters / Fans // -#define HEATER_0_PIN 21 // Extruder -#define HEATER_1_PIN 46 -#define HEATER_2_PIN 47 -#define HEATER_BED_PIN 20 - -// If soft or fast PWM is off then use Teensyduino pin numbering, Marlin -// fastio pin numbering otherwise -#if ENABLED(FAN_SOFT_PWM) || ENABLED(FAST_PWM_FAN) - #define FAN_PIN 22 -#else - #define FAN_PIN 16 -#endif +#define HEATER_0_PIN 15 // C5 PWM3B - Extruder +#define HEATER_1_PIN 44 // F6 +#define HEATER_2_PIN 45 // F7 +#define HEATER_BED_PIN 14 // C4 PWM3C + +#define FAN_PIN 16 // C6 PWM3A // // Misc. Functions // -#define SDSS 20 // Teensylu pin mapping - -#ifndef FILWIDTH_PIN - #define FILWIDTH_PIN 2 // Analog Input -#endif +#define SDSS 20 // B0 SS +#define FILWIDTH_PIN 2 // Analog Input // // LCD / Controller // #if ENABLED(ULTRA_LCD) - #define BEEPER_PIN -1 - - #define LCD_PINS_RS 9 - #define LCD_PINS_ENABLE 8 - #define LCD_PINS_D4 7 - #define LCD_PINS_D5 6 - #define LCD_PINS_D6 5 - #define LCD_PINS_D7 4 - - #define BTN_EN1 16 - #define BTN_EN2 17 - #define BTN_ENC 18 // the click - - #define SD_DETECT_PIN -1 - - // encoder rotation values - #define encrot0 0 - #define encrot1 2 - #define encrot2 3 - #define encrot3 1 + #define BEEPER_PIN -1 + + #define LCD_PINS_RS 9 // E1 JP11-11 + #define LCD_PINS_ENABLE 8 // E0 JP11-10 + #define LCD_PINS_D4 7 // D7 JP11-8 + #define LCD_PINS_D5 6 // D6 JP11-7 + #define LCD_PINS_D6 5 // D5 JP11-6 + #define LCD_PINS_D7 4 // D4 JP11-5 + + #define BTN_EN1 10 // C0 JP11-12 + #define BTN_EN2 11 // C1 JP11-13 + #define BTN_ENC 12 // C2 JP11-14 + + #define SD_DETECT_PIN -1 #endif #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define BEEPER_PIN 32 // FastIO - #define DOGLCD_A0 42 // Non-FastIO - #define DOGLCD_CS 43 // Non-FastIO + #define BEEPER_PIN 8 // E0 JP11-10 + #define DOGLCD_A0 40 // F2 JP2-2 + #define DOGLCD_CS 41 // F3 JP2-4 #define LCD_SCREEN_ROT_180 - // (FastIO Pins) - #define BTN_EN1 26 - #define BTN_EN2 27 - #define BTN_ENC 47 + #define BTN_EN1 2 // D2 TX1 JP2-5 + #define BTN_EN2 3 // D3 RX1 JP2-7 + #define BTN_ENC 45 // F7 TDI JP2-12 - #define SDSS 45 - #define SD_DETECT_PIN -1 // FastIO (Manual says 72) + #define SDSS 43 // F5 TMS JP2-8 + #define SD_DETECT_PIN -1 - #define STAT_LED_RED_PIN 12 // Non-FastIO - #define STAT_LED_BLUE_PIN 10 // Non-FastIO + #define STAT_LED_RED_PIN 12 // C2 JP11-14 + #define STAT_LED_BLUE_PIN 10 // C0 JP11-12 #endif diff --git a/Marlin/pins_SAV_MKI.h b/Marlin/pins_SAV_MKI.h old mode 100644 new mode 100755 index 2048af925..b1ed0bd8c --- a/Marlin/pins_SAV_MKI.h +++ b/Marlin/pins_SAV_MKI.h @@ -1,6 +1,6 @@ /** * Marlin 3D Printer Firmware - * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm @@ -21,14 +21,48 @@ */ /** - * SAV MkI pin assignments (AT90USB1286) - * Requires the Teensyduino software with Teensy++ 2.0 selected in Arduino IDE! - * http://www.pjrc.com/teensy/teensyduino.html - * RepRap Clone Wars project board. + * Rev B 2 JUN 2017 + * + * Converted to Arduino pin numbering + */ + +/** + * There are two Arduino IDE extensions that are compatible with this board + * and with the mainstream Marlin software. + * + * Teensyduino - http://www.pjrc.com/teensy/teensyduino.html + * Select Teensy++ 2.0 in Arduino IDE from the 'Tools -> Boards' menu + * + * Installation instructions are at the above URL. Don't bother loading the + * libraries - they are not used with the Marlin software. + * + * Printrboard - https://github.com/scwimbush/Printrboard-HID-Arduino-IDE-Support + * + * Installation: + * + * 1. Go to the above URL, click on the "Clone or Download" button and then + * click on "Download ZIP" button. + * 2. Unzip the file, find the "printrboard" directory and then copy it to the + * hardware directory in Arduino. The Arduino hardware directory will probably + * be located in a path similar to this: C:\Program Files (x86)\Arduino\hardware. + * 3. Restart Arduino. + * 4. Select "Printrboard" from the 'Tools -> Boards' menu. + * + * Teensyduino is the most popular option. Printrboard is used if your board doesn't have + * the Teensyduino bootloader on it. + */ + +/** + * To burn the bootloader that comes with Printrboard: + * + * 1. Connect your programmer to the board. + * 2. In the Arduino IDE select "Printrboard" and then select the programmer. + * 3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message. + * 4. The programmer is no longer needed. Remove it. */ #ifndef __AVR_AT90USB1286__ - #error "Oops! Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu." + #error "Oops! Make sure you have 'Teensy++ 2.0' or 'Printrboard' selected from the 'Tools -> Boards' menu." #endif #define DEFAULT_MACHINE_NAME "SAV MkI" @@ -41,54 +75,54 @@ // // Servos // -#define SERVO0_PIN 41 // In teensy's pin definition for pinMode (in servo.cpp) +#define SERVO0_PIN 39 // F1 In teensy's pin definition for pinMode (in servo.cpp) // // Limit Switches // -#define X_STOP_PIN 13 -#define Y_STOP_PIN 14 -//#define Z_STOP_PIN 15 -#define Z_STOP_PIN 36 // For inductive sensor. +#define X_STOP_PIN 25 // B5 +#define Y_STOP_PIN 26 // B6 +//#define Z_STOP_PIN 27 // B7 +#define Z_STOP_PIN 36 // E4 For inductive sensor. +//#define E_STOP_PIN 36 // E4 // // Steppers // -#define X_STEP_PIN 0 -#define X_DIR_PIN 1 -#define X_ENABLE_PIN 39 +#define X_STEP_PIN 28 // A0 +#define X_DIR_PIN 29 // A1 +#define X_ENABLE_PIN 19 // E7 -#define Y_STEP_PIN 2 -#define Y_DIR_PIN 3 -#define Y_ENABLE_PIN 38 +#define Y_STEP_PIN 30 // A2 +#define Y_DIR_PIN 31 // A3 +#define Y_ENABLE_PIN 18 // E6 -#define Z_STEP_PIN 4 -#define Z_DIR_PIN 5 -#define Z_ENABLE_PIN 23 +#define Z_STEP_PIN 32 // A4 +#define Z_DIR_PIN 33 // A5 +#define Z_ENABLE_PIN 17 // C7 -#define E0_STEP_PIN 6 -#define E0_DIR_PIN 7 -#define E0_ENABLE_PIN 19 +#define E0_STEP_PIN 34 // A6 +#define E0_DIR_PIN 35 // A7 +#define E0_ENABLE_PIN 13 // C3 // // Temperature Sensors // -#define TEMP_0_PIN 7 // Analog Input (Extruder) -#define TEMP_BED_PIN 6 // Analog Input (Bed) +#define TEMP_0_PIN 7 // F7 Analog Input (Extruder) +#define TEMP_BED_PIN 6 // F6 Analog Input (Bed) // // Heaters / Fans // -#define HEATER_0_PIN 21 // Extruder -#define HEATER_BED_PIN 20 // Bed +#define HEATER_0_PIN 15 // C5 PWM3B - Extruder +#define HEATER_BED_PIN 14 // C4 PWM3C - Bed -#define FAN_PIN 16 // Fan -- from Teensyduino environment. - // For the fan and Teensyduino uses a different pin mapping. +#define FAN_PIN 16 // C6 PWM3A // // Misc. Functions // -#define SDSS 20 // PB0 - 8 in marlin env. +#define SDSS 20 // B0 // Extension header pin mapping // ---------------------------- @@ -99,21 +133,21 @@ // PWM-D24 A4 (An), IO // 5V GND // 12V GND -#define EXT_AUX_SCL_D0 0 // 0 (teensy), 24 (marlin) -#define EXT_AUX_SDA_D1 1 // 1 (teensy), 25 (marlin) -#define EXT_AUX_RX1_D2 26 // 2 (teensy), 26 (marlin) -#define EXT_AUX_TX1_D3 27 // 3 (teensy), 27 (marlin) -#define EXT_AUX_PWM_D24 12 // 24 (teensy), 12 (marlin) -#define EXT_AUX_A0 0 // Analog -#define EXT_AUX_A0_IO 40 // Digital IO, 38 (teensy), 40 (marlin) -#define EXT_AUX_A1 1 // Analog -#define EXT_AUX_A1_IO 41 // Digital IO, 39 (teensy), 41 (marlin) -#define EXT_AUX_A2 2 // Analog -#define EXT_AUX_A2_IO 42 // Digital IO, 40 (teensy), 42 (marlin) -#define EXT_AUX_A3 3 // Analog -#define EXT_AUX_A3_IO 43 // Digital IO, 41 (teensy), 43 (marlin) -#define EXT_AUX_A4 4 // Analog -#define EXT_AUX_A4_IO 44 // Digital IO, 42 (teensy), 44 (marlin) +#define EXT_AUX_SCL_D0 0 // D0 PWM0B +#define EXT_AUX_SDA_D1 1 // D1 +#define EXT_AUX_RX1_D2 2 // D2 +#define EXT_AUX_TX1_D3 3 // D3 +#define EXT_AUX_PWM_D24 24 // B4 PWM2A +#define EXT_AUX_A0 0 // F0 Analog Input +#define EXT_AUX_A0_IO 38 // F0 Digital IO +#define EXT_AUX_A1 1 // F1 Analog Input +#define EXT_AUX_A1_IO 39 // F1 Digital IO +#define EXT_AUX_A2 2 // F2 Analog Input +#define EXT_AUX_A2_IO 40 // F2 Digital IO +#define EXT_AUX_A3 3 // F3 Analog Input +#define EXT_AUX_A3_IO 41 // F3 Digital IO +#define EXT_AUX_A4 4 // F4 Analog Input +#define EXT_AUX_A4_IO 42 // F4 Digital IO // // LCD / Controller @@ -128,28 +162,28 @@ #if ENABLED(SAV_3DLCD) // For LCD SHIFT register LCD - #define SR_DATA_PIN EXT_AUX_SDA_D1 - #define SR_CLK_PIN EXT_AUX_SCL_D0 -#endif // SAV_3DLCD + #define SR_DATA_PIN EXT_AUX_SDA_D1 + #define SR_CLK_PIN EXT_AUX_SCL_D0 +#endif #if ENABLED(SAV_3DLCD) || ENABLED(SAV_3DGLCD) - #define BTN_EN1 EXT_AUX_A1_IO - #define BTN_EN2 EXT_AUX_A0_IO - #define BTN_ENC EXT_AUX_PWM_D24 + #define BTN_EN1 EXT_AUX_A1_IO + #define BTN_EN2 EXT_AUX_A0_IO + #define BTN_ENC EXT_AUX_PWM_D24 - #define KILL_PIN EXT_AUX_A2_IO - #define HOME_PIN EXT_AUX_A4_IO + #define KILL_PIN EXT_AUX_A2_IO + #define HOME_PIN EXT_AUX_A4_IO -#else // Try to use the expansion header for spindle control +#else // Use the expansion header for spindle control // // M3/M4/M5 - Spindle/Laser Control // - #define SPINDLE_LASER_PWM_PIN 24 // 12 AT90USB… pin # - #define SPINDLE_LASER_ENABLE_PIN 39 // Pin should have a pullup! 41 AT90USB… pin # - #define SPINDLE_DIR_PIN 40 // 42 AT90USB… pin # + #define SPINDLE_LASER_PWM_PIN 24 // B4 PWM2A + #define SPINDLE_LASER_ENABLE_PIN 39 // F1 Pin should have a pullup! + #define SPINDLE_DIR_PIN 40 // F2 - #define CASE_LIGHT_PIN 0 // 24 AT90USB… pin # + #define CASE_LIGHT_PIN 0 // D0 PWM0B #endif diff --git a/Marlin/pins_TEENSY2.h b/Marlin/pins_TEENSY2.h old mode 100644 new mode 100755 index 971de27e8..fa4280fc1 --- a/Marlin/pins_TEENSY2.h +++ b/Marlin/pins_TEENSY2.h @@ -1,6 +1,6 @@ /** * Marlin 3D Printer Firmware - * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm @@ -20,13 +20,54 @@ * */ +/** + * Rev B 2 JUN 2017 + * + * Converted to Arduino pin numbering + */ + +/** + * There are two Arduino IDE extensions that are compatible with this board + * and with the mainstream Marlin software. + * + * Teensyduino - http://www.pjrc.com/teensy/teensyduino.html + * Select Teensy++ 2.0 in Arduino IDE from the 'Tools -> Boards' menu + * + * Installation instructions are at the above URL. Don't bother loading the + * libraries - they are not used with the Marlin software. + * + * Printrboard - https://github.com/scwimbush/Printrboard-HID-Arduino-IDE-Support + * + * Installation: + * + * 1. Go to the above URL, click on the "Clone or Download" button and then + * click on "Download ZIP" button. + * 2. Unzip the file, find the "printrboard" directory and then copy it to the + * hardware directory in Arduino. The Arduino hardware directory will probably + * be located in a path similar to this: C:\Program Files (x86)\Arduino\hardware. + * 3. Restart Arduino. + * 4. Select "Printrboard" from the 'Tools -> Boards' menu. + * + * Teensyduino is the most popular option. Printrboard is used if your board doesn't have + * the Teensyduino bootloader on it. + */ + +/** + * To burn the bootloader that comes with Printrboard: + * + * 1. Connect your programmer to the board. + * 2. In the Arduino IDE select "Printrboard" and then select the programmer. + * 3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message. + * 4. The programmer is no longer needed. Remove it. + */ + /** * Teensy++ 2.0 Breadboard pin assignments (AT90USB1286) * Requires the Teensyduino software with Teensy++ 2.0 selected in Arduino IDE! * http://www.pjrc.com/teensy/teensyduino.html * See http://reprap.org/wiki/Printrboard for more info * - * CLI build: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make + * CLI build: HARDWARE_MOTHERBOARD=84 make * * DaveX plan for Teensylu/printrboard-type pinouts for a TeensyBreadboard: * (ref teensylu & sprinter) @@ -66,12 +107,7 @@ */ #ifndef __AVR_AT90USB1286__ - #error "Oops! Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu." -#endif - -#if DISABLED(AT90USBxx_TEENSYPP_ASSIGNMENTS) // use Teensyduino Teensy++2.0 pin assignments instead of Marlin alphabetical. - #error "Uncomment #define AT90USBxx_TEENSYPP_ASSIGNMENTS in fastio.h for this config" - // (or build from command line) + #error "Oops! Make sure you have 'Teensy++ 2.0' or 'Printrboard' selected from the 'Tools -> Boards' menu." #endif #define BOARD_NAME "Teensy++2.0" @@ -82,68 +118,68 @@ // // Limit Switches // -#define X_STOP_PIN 2 -#define Y_STOP_PIN 3 -#define Z_STOP_PIN 4 +#define X_STOP_PIN 2 // D2 +#define Y_STOP_PIN 3 // D3 +#define Z_STOP_PIN 4 // D4 // // Steppers // -#define X_STEP_PIN 28 // 0 Marlin -#define X_DIR_PIN 29 // 1 Marlin -#define X_ENABLE_PIN 26 +#define X_STEP_PIN 28 // A0 Marlin +#define X_DIR_PIN 29 // A1 Marlin +#define X_ENABLE_PIN 26 // B6 -#define Y_STEP_PIN 30 // 2 Marlin -#define Y_DIR_PIN 31 // 3 -#define Y_ENABLE_PIN 26 // Shared w/x +#define Y_STEP_PIN 30 // A2 Marlin +#define Y_DIR_PIN 31 // A3 +#define Y_ENABLE_PIN 26 // B6 Shared w/x -#define Z_STEP_PIN 32 // 4 -#define Z_DIR_PIN 33 // 5 -#define Z_ENABLE_PIN 26 // Shared w/x +#define Z_STEP_PIN 32 // A4 +#define Z_DIR_PIN 33 // A5 +#define Z_ENABLE_PIN 26 // B6 Shared w/x -#define E0_STEP_PIN 34 // 6 -#define E0_DIR_PIN 35 // 7 -#define E0_ENABLE_PIN 26 // Shared w/x +#define E0_STEP_PIN 34 // A6 +#define E0_DIR_PIN 35 // A7 +#define E0_ENABLE_PIN 26 // B6 Shared w/x // // Temperature Sensors // -#define TEMP_0_PIN 7 // Analog Input (Extruder) -#define TEMP_BED_PIN 6 // Analog Input (Bed) +#define TEMP_0_PIN 7 // F7 Analog Input (Extruder) +#define TEMP_BED_PIN 6 // F6 Analog Input (Bed) // // Heaters / Fans // -#define HEATER_0_PIN 15 // 21 // Extruder -#define HEATER_BED_PIN 14 // 20 // Bed -#define FAN_PIN 16 // 22 // Fan +#define HEATER_0_PIN 15 // C5 PWM3B Extruder +#define HEATER_BED_PIN 14 // C4 PWM3C +#define FAN_PIN 16 // C6 PWM3A Fan // // Misc. Functions // -#define SDSS 20 // 8 -#define LED_PIN 6 -#define PS_ON_PIN 27 -#define CASE_LIGHT_PIN 1 // MUST BE HARDWARE PWM +#define SDSS 20 // B0 +#define LED_PIN 6 // D6 +#define PS_ON_PIN 27 // B7 +#define CASE_LIGHT_PIN 1 // D1 PWM2B MUST BE HARDWARE PWM // // LCD / Controller // #if ENABLED(ULTIPANEL) - #define LCD_PINS_RS 8 - #define LCD_PINS_ENABLE 9 - #define LCD_PINS_D4 10 - #define LCD_PINS_D5 11 - #define LCD_PINS_D6 12 - #define LCD_PINS_D7 13 - #define BTN_EN1 38 - #define BTN_EN2 39 - #define BTN_ENC 40 + #define LCD_PINS_RS 8 // E0 + #define LCD_PINS_ENABLE 9 // E1 + #define LCD_PINS_D4 10 // C0 + #define LCD_PINS_D5 11 // C1 + #define LCD_PINS_D6 12 // C2 + #define LCD_PINS_D7 13 // C3 + #define BTN_EN1 38 // F0 + #define BTN_EN2 39 // F1 + #define BTN_ENC 40 // F2 #endif // // M3/M4/M5 - Spindle/Laser Control // -#define SPINDLE_LASER_ENABLE_PIN 5 // Pin should have a pullup! -#define SPINDLE_LASER_PWM_PIN 0 // MUST BE HARDWARE PWM -#define SPINDLE_DIR_PIN 7 +#define SPINDLE_LASER_ENABLE_PIN 5 // D5 Pin should have a pullup! +#define SPINDLE_LASER_PWM_PIN 0 // D0 PWM0B MUST BE HARDWARE PWM +#define SPINDLE_DIR_PIN 7 // D7 diff --git a/Marlin/pins_TEENSYLU.h b/Marlin/pins_TEENSYLU.h old mode 100644 new mode 100755 index 5f12e710c..3fb7f5c3e --- a/Marlin/pins_TEENSYLU.h +++ b/Marlin/pins_TEENSYLU.h @@ -21,54 +21,46 @@ */ /** - * rev B 30 DEC 2016 + * Rev C 2 JUN 2017 * - * The original version of this file did NOT result in a useful program because: - * 1. The pin numbers assumed that the "#define AT90USBxx_TEENSYPP_ASSIGNMENTS" line - * in FASTIO.h was commented out. There wasn't an Arduino IDE 1.6.x extension/package - * that supported this pin map so the latest Marlin wouldn't compile. - * 2. The silkscreen for the four end stops don't agree with the schematic. Activating - * the X endstop would tell the software that the Y endstop just went active. - * 3. The thermistor inputs also had heater names assigned to them. The result was - * thermistor inputs that were set to digital outputs. + * Converted to Arduino pin numbering + */ + +/** + * There are two Arduino IDE extensions that are compatible with this board + * and with the mainstream Marlin software. All have been used with Arduino 1.6.12 + * + * Teensyduino - http://www.pjrc.com/teensy/teensyduino.html + * Select Teensy++ 2.0 in Arduino IDE from the 'Tools -> Boards' menu * - * Rev B corrects the above problems by: - * 1. The "Marlin_AT90USB" extension/package was developed. This extension enables the - * latest Marlin software to compile using Arduino IDE 1.6.x and 1.80. - * 2. The endstop pin numbers in this file were changed to match the silkscreen. This - * makes it a little confusing when trying to correlate the schematic with the pin - * numbers used in this file. - * 3. The offending heater names were deleted. + * Installation instructions are at the above URL. Don't bother loading the + * libraries - they are not used with the Marlin software. * - * To create a useable image for Teensylu do the following: - * a) Install the Marlin_AT90USB extension with either of the following methods: - * Automatic - paste this URL into preferences and then use Boards manager - * https://rawgit.com/Bob-the-Kuhn/Marlin_AT90USB/master/package_MARLIN_AT90USB_index.json - * Manual: - * 1. Copy the following URL into Go to "https://github.com/Bob-the-Kuhn/Marlin_AT90USB", - * click on the "Clone or Download" button and then click on "Download ZIP" button. - * 2. Unzip the file, find the "Marlin_AT90USB" directory and then copy it to the - * hardware directory in Arduino. The Arduino hardware directory will probably be - * located in a path similar to this: C:\Program Files (x86)\Arduino\hardware - * b) Connect the USBtinyISP to the board. - * c) In the Arduino IDE select the "AT90USB1286_STANDARD" board in the of the "Marlin_AT90USB" - * section and select the "USBtinyISP" programmer. - * d) In the Arduino IDE click on "burn bootloader". Don't worry about the "verify - * failed at 1F000" error message. - * e) The USBtinyISP programmer is no longer needed. Remove it. - * f) In FASTIO.h comment out the "#define AT90USBxx_TEENSYPP_ASSIGNMENTS" line. - * g) To upload a sketch do the following: - * 1. remove the jumper - * 2. press reset - * 3. click on the "upload" button in the Arduino IDE - * 4. wait until the upload finishes (less than a minute) - * 5. put the jumper back on - * 6. press the reset button + * Printrboard - https://github.com/scwimbush/Printrboard-HID-Arduino-IDE-Support + * This is basically Teensyduino but with a bootloader that can handle image sizes + * larger than 64K. * + * Installation: + * + * 1. Go to the above URL, click on the "Clone or Download" button and then + * click on "Download ZIP" button. + * 2. Unzip the file, find the "printrboard" directory and then copy it to the + * hardware directory in Arduino. The Arduino hardware directory will probably + * be located in a path similar to this: C:\Program Files (x86)\Arduino\hardware. + * 3. Restart Arduino. + * 4. Select "Printrboard" from the 'Tools -> Boards' menu. + * + * Teensyduino is the most popular option. Printrboard is used if your board doesn't have + * the Teensyduino bootloader on it. + */ + +/** + * To burn the bootloader that comes with Printrboard: * - * NOTE - the "Marlin_AT90USB" pin maps make PWM0A available rather than the usual PWM1C. - * These PWMs share the same physical pin. Marlin uses TIMER1 to generate - * interrupts and sets it up such that PWM1A, PWM1B & PWM1C can't be used. + * 1. Connect your programmer to the board. + * 2. In the Arduino IDE select "Printrboard" and then select the programmer. + * 3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message. + * 4. The programmer is no longer needed. Remove it. */ /** @@ -81,13 +73,8 @@ * The pin assignments in this file match the silkscreen. */ - #if !defined(__AVR_AT90USB1286__) && !defined(__AVR_AT90USB1286P__) - #error "Oops! Make sure you have 'AT90USB1286_STANDARD' selected from the 'Tools -> Boards' menu." -#endif - -#if ENABLED(AT90USBxx_TEENSYPP_ASSIGNMENTS) - #error "please disable (comment out) the AT90USBxx_TEENSYPP_ASSIGNMENTS flag in FASTIO.h " + #error "Oops! Make sure you have 'Teensy++ 2.0' or 'Printrboard' selected from the 'Tools -> Boards' menu." #endif #define BOARD_NAME "Teensylu" @@ -97,60 +84,60 @@ // -// Limit Switche definitions that match the SCHEMATIC +// Limit Switch definitions that match the SCHEMATIC // -//#define X_STOP_PIN 13 -//#define Y_STOP_PIN 14 -//#define Z_STOP_PIN 15 -//#define E_STOP_PIN 36 +//#define X_STOP_PIN 25 // B5 +//#define Y_STOP_PIN 26 // B6 +//#define Z_STOP_PIN 27 // B7 +//#define E_STOP_PIN 36 // E4 // // Limit Switch definitions that match the SILKSCREEN // -#define X_STOP_PIN 14 -#define Y_STOP_PIN 15 -#define Z_STOP_PIN 36 -//#define E_STOP_PIN 13 +#define X_STOP_PIN 26 // B6 +#define Y_STOP_PIN 27 // B7 +#define Z_STOP_PIN 36 // E4 +//#define E_STOP_PIN 25 // B5 // // Steppers // -#define X_STEP_PIN 0 -#define X_DIR_PIN 1 -#define X_ENABLE_PIN 39 +#define X_STEP_PIN 28 // A0 +#define X_DIR_PIN 29 // A1 +#define X_ENABLE_PIN 19 // E7 -#define Y_STEP_PIN 2 -#define Y_DIR_PIN 3 -#define Y_ENABLE_PIN 38 +#define Y_STEP_PIN 30 // A2 +#define Y_DIR_PIN 31 // A3 +#define Y_ENABLE_PIN 18 // E6 -#define Z_STEP_PIN 4 -#define Z_DIR_PIN 5 -#define Z_ENABLE_PIN 23 - -#define E0_STEP_PIN 6 -#define E0_DIR_PIN 7 -#define E0_ENABLE_PIN 19 +#define Z_STEP_PIN 32 // A4 +#define Z_DIR_PIN 33 // A5 +#define Z_ENABLE_PIN 17 // C7 +#define E0_STEP_PIN 34 // A6 +#define E0_DIR_PIN 35 // A7 +#define E0_ENABLE_PIN 13 // C3 +// // Temperature Sensors - -#define TEMP_0_PIN 7 // Analog Input (Extruder) -#define TEMP_BED_PIN 6 // Analog Input (Bed) +// +#define TEMP_0_PIN 7 // Analog Input (Extruder) +#define TEMP_BED_PIN 6 // Analog Input (Bed) // // Heaters / Fans // -#define HEATER_0_PIN 21 // Extruder -#define HEATER_BED_PIN 20 +#define HEATER_0_PIN 15 // C5 PWM3B - Extruder +#define HEATER_BED_PIN 14 // C4 PWM3C -#define FAN_PIN 22 +#define FAN_PIN 16 // C6 PWM3A // // Misc. Functions // -#define SDSS 8 -#define CASE_LIGHT_PIN 24 +#define SDSS 20 // B0 JP31-6 +#define CASE_LIGHT_PIN 0 // D0 IO-14 PWM0B // // LCD / Controller @@ -160,11 +147,11 @@ #define BEEPER_PIN -1 #if ENABLED(LCD_I2C_PANELOLU2) - #define BTN_EN1 27 - #define BTN_EN2 26 - #define BTN_ENC 43 - #define SDSS 40 // use SD card on Panelolu2 - #endif // LCD_I2C_PANELOLU2 + #define BTN_EN1 3 // D3 IO-8 + #define BTN_EN2 2 // D2 IO-10 + #define BTN_ENC 41 // F3 IO-7 + #define SDSS 38 // F0 IO-13 use SD card on Panelolu2 + #endif #define SD_DETECT_PIN -1 @@ -173,6 +160,6 @@ // // M3/M4/M5 - Spindle/Laser Control // -#define SPINDLE_LASER_PWM_PIN 12 // MUST BE HARDWARE PWM -#define SPINDLE_LASER_ENABLE_PIN 41 // Pin should have a pullup! -#define SPINDLE_DIR_PIN 42 +#define SPINDLE_LASER_PWM_PIN 24 // B4 IO-3 PWM2A - MUST BE HARDWARE PWM +#define SPINDLE_LASER_ENABLE_PIN 39 // F1 IO-11 - Pin should have a pullup! +#define SPINDLE_DIR_PIN 40 // F2 IO-9