diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 97d2d95f9..16865c487 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -223,16 +223,16 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board
+                                    //  pins_XXX.h file overrides this one
+  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0
   #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
   #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
                                               // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1029,7 +1029,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/boards.h b/Marlin/boards.h
index 6594b30fa..24ab48c86 100644
--- a/Marlin/boards.h
+++ b/Marlin/boards.h
@@ -95,7 +95,7 @@
 #define BOARD_BAM_DICE          401  // 2PrintBeta BAM&DICE with STK drivers
 #define BOARD_BAM_DICE_DUE      402  // 2PrintBeta BAM&DICE Due with STK drivers
 #define BOARD_BQ_ZUM_MEGA_3D    503  // bq ZUM Mega 3D
-#define BOARD_ZRIB_V20          504  // zrib V2.0 control board (Chinese knock off RAMPS replica) 
+#define BOARD_ZRIB_V20          504  // zrib V2.0 control board (Chinese knock off RAMPS replica)
 
 #define MB(board) (MOTHERBOARD==BOARD_##board)
 
diff --git a/Marlin/example_configurations/Cartesio/Configuration_adv.h b/Marlin/example_configurations/Cartesio/Configuration_adv.h
index 4eec94c07..36d2a4366 100644
--- a/Marlin/example_configurations/Cartesio/Configuration_adv.h
+++ b/Marlin/example_configurations/Cartesio/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1022,7 +1020,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/Felix/Configuration_adv.h b/Marlin/example_configurations/Felix/Configuration_adv.h
index f3b44a466..8a09f18c0 100644
--- a/Marlin/example_configurations/Felix/Configuration_adv.h
+++ b/Marlin/example_configurations/Felix/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1022,7 +1020,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/FolgerTech-i3-2020/Configuration_adv.h b/Marlin/example_configurations/FolgerTech-i3-2020/Configuration_adv.h
index 662d679a8..a5fd5c5e6 100644
--- a/Marlin/example_configurations/FolgerTech-i3-2020/Configuration_adv.h
+++ b/Marlin/example_configurations/FolgerTech-i3-2020/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1031,7 +1029,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/Hephestos/Configuration_adv.h b/Marlin/example_configurations/Hephestos/Configuration_adv.h
index c4843b6ec..de751085a 100644
--- a/Marlin/example_configurations/Hephestos/Configuration_adv.h
+++ b/Marlin/example_configurations/Hephestos/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1022,7 +1020,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h
index 385adadb9..09e91b5d8 100644
--- a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h
+++ b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1006,7 +1004,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/K8200/Configuration_adv.h b/Marlin/example_configurations/K8200/Configuration_adv.h
index 482d89a98..ddb740486 100644
--- a/Marlin/example_configurations/K8200/Configuration_adv.h
+++ b/Marlin/example_configurations/K8200/Configuration_adv.h
@@ -236,16 +236,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1035,7 +1033,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/K8400/Configuration_adv.h b/Marlin/example_configurations/K8400/Configuration_adv.h
index e3c6ccf26..a52988805 100644
--- a/Marlin/example_configurations/K8400/Configuration_adv.h
+++ b/Marlin/example_configurations/K8400/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1022,7 +1020,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/M150/Configuration_adv.h b/Marlin/example_configurations/M150/Configuration_adv.h
index 2253ce435..3962f2d40 100644
--- a/Marlin/example_configurations/M150/Configuration_adv.h
+++ b/Marlin/example_configurations/M150/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1029,7 +1027,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/RigidBot/Configuration_adv.h b/Marlin/example_configurations/RigidBot/Configuration_adv.h
index 570538c59..f939c4d2c 100644
--- a/Marlin/example_configurations/RigidBot/Configuration_adv.h
+++ b/Marlin/example_configurations/RigidBot/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1022,7 +1020,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/SCARA/Configuration_adv.h b/Marlin/example_configurations/SCARA/Configuration_adv.h
index 718a4b90b..7fe55a0b7 100644
--- a/Marlin/example_configurations/SCARA/Configuration_adv.h
+++ b/Marlin/example_configurations/SCARA/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1022,7 +1020,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/TAZ4/Configuration_adv.h b/Marlin/example_configurations/TAZ4/Configuration_adv.h
index a833712b0..5ee685360 100644
--- a/Marlin/example_configurations/TAZ4/Configuration_adv.h
+++ b/Marlin/example_configurations/TAZ4/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1022,7 +1020,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/TinyBoy2/Configuration_adv.h b/Marlin/example_configurations/TinyBoy2/Configuration_adv.h
index 3de9a920c..b6e6175fb 100644
--- a/Marlin/example_configurations/TinyBoy2/Configuration_adv.h
+++ b/Marlin/example_configurations/TinyBoy2/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1025,7 +1023,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/WITBOX/Configuration_adv.h b/Marlin/example_configurations/WITBOX/Configuration_adv.h
index c4843b6ec..de751085a 100644
--- a/Marlin/example_configurations/WITBOX/Configuration_adv.h
+++ b/Marlin/example_configurations/WITBOX/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1022,7 +1020,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h
index 1d798fb94..51f95e1f2 100644
--- a/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1027,7 +1025,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h
index 5363cb3f6..c9dc15e7a 100644
--- a/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1026,7 +1024,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/delta/generic/Configuration_adv.h b/Marlin/example_configurations/delta/generic/Configuration_adv.h
index 53a86374b..334fba863 100644
--- a/Marlin/example_configurations/delta/generic/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/generic/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1024,7 +1022,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
index 53a86374b..334fba863 100644
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1024,7 +1022,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
index 5798c53e7..d46820b12 100644
--- a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
@@ -228,16 +228,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1029,7 +1027,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h
index fdc295253..6440d1611 100644
--- a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1024,7 +1022,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/gCreate_gMax1.5+/Configuration_adv.h b/Marlin/example_configurations/gCreate_gMax1.5+/Configuration_adv.h
index 4814b7a24..799acd32a 100644
--- a/Marlin/example_configurations/gCreate_gMax1.5+/Configuration_adv.h
+++ b/Marlin/example_configurations/gCreate_gMax1.5+/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1031,7 +1029,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/makibox/Configuration_adv.h b/Marlin/example_configurations/makibox/Configuration_adv.h
index fbbb86690..026e2443a 100644
--- a/Marlin/example_configurations/makibox/Configuration_adv.h
+++ b/Marlin/example_configurations/makibox/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1022,7 +1020,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
index 2a5b63492..249166ca1 100644
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1022,7 +1020,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/example_configurations/wt150/Configuration_adv.h b/Marlin/example_configurations/wt150/Configuration_adv.h
index f78a297fc..245eeee21 100644
--- a/Marlin/example_configurations/wt150/Configuration_adv.h
+++ b/Marlin/example_configurations/wt150/Configuration_adv.h
@@ -223,16 +223,14 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE 
-#if ENABLED(CASE_LIGHT_ENABLE) 
-  #define CASE_LIGHT_PIN 4          // can be defined here or in the pins_XXX.h file for your board 
-                                    //  pins_XXX.h file overrides this one 
-  #define INVERT_CASE_LIGHT false             // set to true if case light is ON when pin is at 0 
-  #define CASE_LIGHT_DEFAULT_ON true          // set default power up state to on or off
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // set power up brightness 0-255 ( only used if on PWM
-                                              // and if CASE_LIGHT_DEFAULT is set to on
-  //#define MENU_ITEM_CASE_LIGHT              // Uncomment to have a Case Light entry in main menu 
-#endif 
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
+  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+#endif
 
 //===========================================================================
 //============================ Mechanical Settings ==========================
@@ -1025,7 +1023,7 @@
    */
   #define  TMC2130_ADV() {  }
 
-#endif // ENABLED(HAVE_TMC2130)
+#endif // HAVE_TMC2130
 
 // @section L6470
 
diff --git a/Marlin/gcode.cpp b/Marlin/gcode.cpp
index 0cb233733..d23db21f7 100644
--- a/Marlin/gcode.cpp
+++ b/Marlin/gcode.cpp
@@ -183,7 +183,7 @@ void GCodeParser::parse(char *p) {
     #endif
 
     if (PARAM_TEST) {
-    
+
       while (*p == ' ') p++;                    // skip spaces vetween parameters & values
       const bool has_num = DECIMAL_SIGNED(*p);  // The parameter has a number [-+0-9.]