diff --git a/Marlin/Conditionals_LCD.h b/Marlin/Conditionals_LCD.h
index 33bb7f90d..28937590d 100644
--- a/Marlin/Conditionals_LCD.h
+++ b/Marlin/Conditionals_LCD.h
@@ -46,6 +46,21 @@
#define NEWPANEL
#define DEFAULT_LCD_CONTRAST 17
+ #elif ENABLED(ANET_KEYPAD_LCD)
+
+ #define REPRAPWORLD_KEYPAD
+ #define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0
+ #define ADC_KEYPAD
+ #define ADC_KEY_NUM 8
+ #define ULTIPANEL
+ // this helps to implement ADC_KEYPAD menus
+ #define ENCODER_STEPS_PER_MENU_ITEM 1
+ #define REVERSE_MENU_DIRECTION
+
+ #elif ENABLED(ANET_FULL_GRAPHICS_LCD)
+
+ #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+
#elif ENABLED(BQ_LCD_SMART_CONTROLLER)
#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
diff --git a/Marlin/SanityCheck.h b/Marlin/SanityCheck.h
index de5c04157..f12d37b44 100644
--- a/Marlin/SanityCheck.h
+++ b/Marlin/SanityCheck.h
@@ -1102,7 +1102,7 @@ static_assert(1 >= 0
#if ENABLED(MINIPANEL)
+ 1
#endif
- #if ENABLED(REPRAPWORLD_KEYPAD) && DISABLED(CARTESIO_UI)
+ #if ENABLED(REPRAPWORLD_KEYPAD) && DISABLED(CARTESIO_UI) && DISABLED(ANET_KEYPAD_LCD)
+ 1
#endif
#if ENABLED(RIGIDBOT_PANEL)
@@ -1138,6 +1138,9 @@ static_assert(1 >= 0
#if ENABLED(OLED_PANEL_TINYBOY2)
+ 1
#endif
+ #if ENABLED(ANET_KEYPAD_LCD)
+ + 1
+ #endif
, "Please select no more than one LCD controller option."
);
diff --git a/Marlin/boards.h b/Marlin/boards.h
index 1ce5a2140..13c9ab887 100644
--- a/Marlin/boards.h
+++ b/Marlin/boards.h
@@ -59,6 +59,7 @@
#define BOARD_MELZI_MAKR3D 66 // Melzi with ATmega1284 (MaKr3d version)
#define BOARD_AZTEEG_X3 67 // Azteeg X3
#define BOARD_AZTEEG_X3_PRO 68 // Azteeg X3 Pro
+#define BOARD_ANET_10 69 // Anet 1.0 (Melzi clone)
#define BOARD_ULTIMAKER 7 // Ultimaker
#define BOARD_ULTIMAKER_OLD 71 // Ultimaker (Older electronics. Pre 1.5.4. This is rare)
#define BOARD_ULTIMAIN_2 72 // Ultimainboard 2.x (Uses TEMP_SENSOR 20)
diff --git a/Marlin/example_configurations/Anet/Configuration.h b/Marlin/example_configurations/Anet/Configuration.h
new file mode 100644
index 000000000..ac1611530
--- /dev/null
+++ b/Marlin/example_configurations/Anet/Configuration.h
@@ -0,0 +1,1607 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see .
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
+#ifndef CONFIGURATION_H
+#define CONFIGURATION_H
+#define CONFIGURATION_H_VERSION 010100
+
+//===========================================================================
+//============================= Getting Started =============================
+//===========================================================================
+
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
+ * http://reprap.org/wiki/Calibration
+ * http://youtu.be/wAL9d7FgInk
+ * http://calculator.josefprusa.cz
+ * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
+ * http://www.thingiverse.com/thing:5573
+ * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
+ * http://www.thingiverse.com/thing:298812
+ */
+
+//===========================================================================
+//============================= DELTA Printer ===============================
+//===========================================================================
+// For a Delta printer replace the configuration files with the files in the
+// example_configurations/delta directory.
+//
+
+//===========================================================================
+//============================= SCARA Printer ===============================
+//===========================================================================
+// For a Scara printer replace the configuration files with the files in the
+// example_configurations/SCARA directory.
+//
+
+// @section info
+
+// User-specified version info of this build to display in [Pronterface, etc] terminal window during
+// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
+// build by the user have been successfully uploaded into firmware.
+#define STRING_CONFIG_H_AUTHOR "(Bob Kuhn, Anet config)" // Who made the changes.
+#define SHOW_BOOTSCREEN
+#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
+#define STRING_SPLASH_LINE2 "Marlin " SHORT_BUILD_VERSION // will be shown during bootup in line 2
+
+//
+// *** VENDORS PLEASE READ *****************************************************
+//
+// Marlin now allow you to have a vendor boot image to be displayed on machine
+// start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
+// custom boot image and then the default Marlin boot image is shown.
+//
+// We suggest for you to take advantage of this new feature and keep the Marlin
+// boot image unmodified. For an example have a look at the bq Hephestos 2
+// example configuration folder.
+//
+//#define SHOW_CUSTOM_BOOTSCREEN
+// @section machine
+
+/**
+ * Select which serial port on the board will be used for communication with the host.
+ * This allows the connection of wireless adapters (for instance) to non-default port pins.
+ * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
+ *
+ * :[0, 1, 2, 3, 4, 5, 6, 7]
+ */
+#define SERIAL_PORT 0
+
+/**
+ * This setting determines the communication speed of the printer.
+ *
+ * 250000 works in most cases, but you might try a lower speed if
+ * you commonly experience drop-outs during host printing.
+ *
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ */
+#define BAUDRATE 115200
+
+// Enable the Bluetooth serial interface on AT90USB devices
+//#define BLUETOOTH
+
+// The following define selects which electronics board you have.
+// Please choose the name from boards.h that matches your setup
+#ifndef MOTHERBOARD
+ #define MOTHERBOARD BOARD_ANET_10
+#endif
+
+// Optional custom name for your RepStrap or other custom machine
+// Displayed in the LCD "Ready" message
+//#define CUSTOM_MACHINE_NAME "3D Printer"
+
+// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
+// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
+//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
+
+// @section extruder
+
+// This defines the number of extruders
+// :[1, 2, 3, 4, 5]
+#define EXTRUDERS 1
+
+// For Cyclops or any "multi-extruder" that shares a single nozzle.
+//#define SINGLENOZZLE
+
+// A dual extruder that uses a single stepper motor
+//#define SWITCHING_EXTRUDER
+#if ENABLED(SWITCHING_EXTRUDER)
+ #define SWITCHING_EXTRUDER_SERVO_NR 0
+ #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
+#endif
+
+// A dual-nozzle that uses a servomotor to raise/lower one of the nozzles
+//#define SWITCHING_NOZZLE
+#if ENABLED(SWITCHING_NOZZLE)
+ #define SWITCHING_NOZZLE_SERVO_NR 0
+ #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
+ //#define HOTEND_OFFSET_Z { 0.0, 0.0 }
+#endif
+
+/**
+ * "Mixing Extruder"
+ * - Adds a new code, M165, to set the current mix factors.
+ * - Extends the stepping routines to move multiple steppers in proportion to the mix.
+ * - Optional support for Repetier Firmware M163, M164, and virtual extruder.
+ * - This implementation supports only a single extruder.
+ * - Enable DIRECT_MIXING_IN_G1 for Pia Taubert's reference implementation
+ */
+//#define MIXING_EXTRUDER
+#if ENABLED(MIXING_EXTRUDER)
+ #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
+ #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
+ //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
+#endif
+
+// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
+// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
+// For the other hotends it is their distance from the extruder 0 hotend.
+//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
+//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
+
+// @section machine
+
+/**
+ * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ *
+ * 0 = No Power Switch
+ * 1 = ATX
+ * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
+ *
+ * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ */
+#define POWER_SUPPLY 0
+
+#if POWER_SUPPLY > 0
+ // Enable this option to leave the PSU off at startup.
+ // Power to steppers and heaters will need to be turned on with M80.
+ //#define PS_DEFAULT_OFF
+#endif
+
+// @section temperature
+
+//===========================================================================
+//============================= Thermal Settings ============================
+//===========================================================================
+
+/**
+ * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ *
+ * Temperature sensors available:
+ *
+ * -3 : thermocouple with MAX31855 (only for sensor 0)
+ * -2 : thermocouple with MAX6675 (only for sensor 0)
+ * -1 : thermocouple with AD595
+ * 0 : not used
+ * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
+ * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
+ * 3 : Mendel-parts thermistor (4.7k pullup)
+ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
+ * 5 : 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
+ * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
+ * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
+ * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
+ * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
+ * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
+ * 10 : 100k RS thermistor 198-961 (4.7k pullup)
+ * 11 : 100k beta 3950 1% thermistor (4.7k pullup)
+ * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
+ * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
+ * 20 : the PT100 circuit found in the Ultimainboard V2.x
+ * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
+ * 66 : 4.7M High Temperature thermistor from Dyze Design
+ * 70 : the 100K thermistor found in the bq Hephestos 2
+ * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
+ *
+ * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
+ * (but gives greater accuracy and more stable PID)
+ * 51 : 100k thermistor - EPCOS (1k pullup)
+ * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
+ * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
+ *
+ * 1047 : Pt1000 with 4k7 pullup
+ * 1010 : Pt1000 with 1k pullup (non standard)
+ * 147 : Pt100 with 4k7 pullup
+ * 110 : Pt100 with 1k pullup (non standard)
+ *
+ * Use these for Testing or Development purposes. NEVER for production machine.
+ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
+ * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
+ * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
+ */
+#define TEMP_SENSOR_0 5
+#define TEMP_SENSOR_1 0
+#define TEMP_SENSOR_2 0
+#define TEMP_SENSOR_3 0
+#define TEMP_SENSOR_4 0
+#define TEMP_SENSOR_BED 5
+
+// Dummy thermistor constant temperature readings, for use with 998 and 999
+#define DUMMY_THERMISTOR_998_VALUE 25
+#define DUMMY_THERMISTOR_999_VALUE 100
+
+// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
+// from the two sensors differ too much the print will be aborted.
+//#define TEMP_SENSOR_1_AS_REDUNDANT
+#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
+
+// Extruder temperature must be close to target for this long before M109 returns success
+#define TEMP_RESIDENCY_TIME 6 // (seconds)
+#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
+
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 6 // (seconds)
+#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
+
+// The minimal temperature defines the temperature below which the heater will not be enabled It is used
+// to check that the wiring to the thermistor is not broken.
+// Otherwise this would lead to the heater being powered on all the time.
+#define HEATER_0_MINTEMP 5
+#define HEATER_1_MINTEMP 5
+#define HEATER_2_MINTEMP 5
+#define HEATER_3_MINTEMP 5
+#define HEATER_4_MINTEMP 5
+#define BED_MINTEMP 5
+
+// When temperature exceeds max temp, your heater will be switched off.
+// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
+// You should use MINTEMP for thermistor short/failure protection.
+#define HEATER_0_MAXTEMP 275
+#define HEATER_1_MAXTEMP 275
+#define HEATER_2_MAXTEMP 275
+#define HEATER_3_MAXTEMP 275
+#define HEATER_4_MAXTEMP 275
+#define BED_MAXTEMP 130
+
+//===========================================================================
+//============================= PID Settings ================================
+//===========================================================================
+// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
+
+// Comment the following line to disable PID and enable bang-bang.
+#define PIDTEMP
+#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#if ENABLED(PIDTEMP)
+ //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
+ //#define PID_DEBUG // Sends debug data to the serial port.
+ //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
+ //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
+ //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
+ // Set/get with gcode: M301 E[extruder number, 0-2]
+ #define PID_FUNCTIONAL_RANGE 15 // If the temperature difference between the target temperature and the actual temperature
+ // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+ #define K1 0.95 //smoothing factor within the PID
+
+ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
+
+ // Ultimaker
+ //#define DEFAULT_Kp 21.0
+ //#define DEFAULT_Ki 1.25
+ //#define DEFAULT_Kd 86.0
+
+ // MakerGear
+ //#define DEFAULT_Kp 7.0
+ //#define DEFAULT_Ki 0.1
+ //#define DEFAULT_Kd 12
+
+ // Mendel Parts V9 on 12V
+ //#define DEFAULT_Kp 63.0
+ //#define DEFAULT_Ki 2.25
+ //#define DEFAULT_Kd 440
+
+ // ANET A8 Standard Extruder at 210 Degree Celsius and 100% Fan
+ //(measured after M106 S255 with M303 E0 S210 C8)
+ #define DEFAULT_Kp 21.0
+ #define DEFAULT_Ki 1.25
+ #define DEFAULT_Kd 86.0
+
+#endif // PIDTEMP
+
+//===========================================================================
+//============================= PID > Bed Temperature Control ===============
+//===========================================================================
+// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
+//
+// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
+// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
+// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
+// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
+// If your configuration is significantly different than this and you don't understand the issues involved, you probably
+// shouldn't use bed PID until someone else verifies your hardware works.
+// If this is enabled, find your own PID constants below.
+//#define PIDTEMPBED
+
+#define BED_LIMIT_SWITCHING
+
+// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
+// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
+// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
+// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
+#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
+
+#if ENABLED(PIDTEMPBED)
+
+ //#define PID_BED_DEBUG // Sends debug data to the serial port.
+
+ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+ //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
+ #define DEFAULT_bedKp 10.00
+ #define DEFAULT_bedKi .023
+ #define DEFAULT_bedKd 305.4
+
+ //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+ //from pidautotune
+ //#define DEFAULT_bedKp 97.1
+ //#define DEFAULT_bedKi 1.41
+ //#define DEFAULT_bedKd 1675.16
+
+ // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
+#endif // PIDTEMPBED
+
+// @section extruder
+
+// This option prevents extrusion if the temperature is below EXTRUDE_MINTEMP.
+// It also enables the M302 command to set the minimum extrusion temperature
+// or to allow moving the extruder regardless of the hotend temperature.
+// *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
+#define PREVENT_COLD_EXTRUSION
+#define EXTRUDE_MINTEMP 170
+
+// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
+// Note that for Bowden Extruders a too-small value here may prevent loading.
+#define PREVENT_LENGTHY_EXTRUDE
+#define EXTRUDE_MAXLENGTH 200
+
+//===========================================================================
+//======================== Thermal Runaway Protection =======================
+//===========================================================================
+
+/**
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * If you get "Thermal Runaway" or "Heating failed" errors the
+ * details can be tuned in Configuration_adv.h
+ */
+
+#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
+#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
+
+//===========================================================================
+//============================= Mechanical Settings =========================
+//===========================================================================
+
+// @section machine
+
+// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
+// either in the usual order or reversed
+//#define COREXY
+//#define COREXZ
+//#define COREYZ
+//#define COREYX
+//#define COREZX
+//#define COREZY
+
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
+// @section homing
+
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
+// coarse Endstop Settings
+#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
+
+#if DISABLED(ENDSTOPPULLUPS)
+ // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
+ //#define ENDSTOPPULLUP_XMAX
+ //#define ENDSTOPPULLUP_YMAX
+ //#define ENDSTOPPULLUP_ZMAX
+ //#define ENDSTOPPULLUP_XMIN
+ //#define ENDSTOPPULLUP_YMIN
+ //#define ENDSTOPPULLUP_ZMIN
+ //#define ENDSTOPPULLUP_ZMIN_PROBE
+#endif
+
+// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
+#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe.
+
+// Enable this feature if all enabled endstop pins are interrupt-capable.
+// This will remove the need to poll the interrupt pins, saving many CPU cycles.
+#define ENDSTOP_INTERRUPTS_FEATURE
+
+//=============================================================================
+//============================== Movement Settings ============================
+//=============================================================================
+// @section motion
+
+/**
+ * Default Settings
+ *
+ * These settings can be reset by M502
+ *
+ * Note that if EEPROM is enabled, saved values will override these.
+ */
+
+/**
+ * With this option each E stepper can have its own factors for the
+ * following movement settings. If fewer factors are given than the
+ * total number of extruders, the last value applies to the rest.
+ */
+//#define DISTINCT_E_FACTORS
+
+/**
+ * Default Axis Steps Per Unit (steps/mm)
+ * Override with M92
+ * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
+ */
+#define DEFAULT_AXIS_STEPS_PER_UNIT {100, 100, 400, 95}
+
+/**
+ * Default Max Feed Rate (mm/s)
+ * Override with M203
+ * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
+ */
+#define DEFAULT_MAX_FEEDRATE {400, 400, 8, 50}
+
+/**
+ * Default Max Acceleration (change/s) change = mm/s
+ * (Maximum start speed for accelerated moves)
+ * Override with M201
+ * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
+ */
+#define DEFAULT_MAX_ACCELERATION {2000, 2000, 100, 10000}
+
+/**
+ * Default Acceleration (change/s) change = mm/s
+ * Override with M204
+ *
+ * M204 P Acceleration
+ * M204 R Retract Acceleration
+ * M204 T Travel Acceleration
+ */
+#define DEFAULT_ACCELERATION 400 // X, Y, Z and E acceleration for printing moves
+#define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration for retracts
+#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves
+
+/**
+ * Default Jerk (mm/s)
+ * Override with M205 X Y Z E
+ *
+ * "Jerk" specifies the minimum speed change that requires acceleration.
+ * When changing speed and direction, if the difference is less than the
+ * value set here, it may happen instantaneously.
+ */
+#define DEFAULT_XJERK 20.0
+#define DEFAULT_YJERK 20.0
+#define DEFAULT_ZJERK 0.3
+#define DEFAULT_EJERK 5.0
+
+
+//===========================================================================
+//============================= Z Probe Options =============================
+//===========================================================================
+// @section probes
+
+//
+// See http://marlinfw.org/configuration/probes.html
+//
+
+/**
+ * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
+ *
+ * Enable this option for a probe connected to the Z Min endstop pin.
+ */
+#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
+
+/**
+ * Z_MIN_PROBE_ENDSTOP
+ *
+ * Enable this option for a probe connected to any pin except Z-Min.
+ * (By default Marlin assumes the Z-Max endstop pin.)
+ * To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
+ *
+ * - The simplest option is to use a free endstop connector.
+ * - Use 5V for powered (usually inductive) sensors.
+ *
+ * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
+ * - For simple switches connect...
+ * - normally-closed switches to GND and D32.
+ * - normally-open switches to 5V and D32.
+ *
+ * WARNING: Setting the wrong pin may have unexpected and potentially
+ * disastrous consequences. Use with caution and do your homework.
+ *
+ */
+//#define Z_MIN_PROBE_ENDSTOP
+
+/**
+ * Probe Type
+ *
+ * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
+ * Activate one of these to use Auto Bed Leveling below.
+ */
+
+/**
+ * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
+ * Use G29 repeatedly, adjusting the Z height at each point with movement commands
+ * or (with LCD_BED_LEVELING) the LCD controller.
+ */
+//#define PROBE_MANUALLY
+
+/**
+ * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
+ * (e.g., an inductive probe or a nozzle-based probe-switch.)
+ */
+//#define FIX_MOUNTED_PROBE
+
+/**
+ * Z Servo Probe, such as an endstop switch on a rotating arm.
+ */
+//#define Z_ENDSTOP_SERVO_NR 0 // Defaults to SERVO 0 connector.
+//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles
+
+/**
+ * The BLTouch probe uses a Hall effect sensor and emulates a servo.
+ */
+//#define BLTOUCH
+#if ENABLED(BLTOUCH)
+ //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed
+#endif
+
+/**
+ * Enable if probing seems unreliable. Heaters and/or fans - consistent with the
+ * options selected below - will be disabled during probing so as to minimize
+ * potential EM interference by quieting/silencing the source of the 'noise' (the change
+ * in current flowing through the wires). This is likely most useful to users of the
+ * BLTouch probe, but may also help those with inductive or other probe types.
+ */
+//#define PROBING_HEATERS_OFF // Turn heaters off when probing
+//#define PROBING_FANS_OFF // Turn fans off when probing
+
+// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
+//#define SOLENOID_PROBE
+
+// A sled-mounted probe like those designed by Charles Bell.
+//#define Z_PROBE_SLED
+//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
+
+//
+// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
+//
+
+/**
+ * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ * X and Y offsets must be integers.
+ *
+ * In the following example the X and Y offsets are both positive:
+ * #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ * +-- BACK ---+
+ * | |
+ * L | (+) P | R <-- probe (20,20)
+ * E | | I
+ * F | (-) N (+) | G <-- nozzle (10,10)
+ * T | | H
+ * | (-) | T
+ * | |
+ * O-- FRONT --+
+ * (0,0)
+ */
+#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle]
+#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle]
+#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
+
+// X and Y axis travel speed (mm/m) between probes
+#define XY_PROBE_SPEED 6000
+
+// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
+#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
+
+// Speed for the "accurate" probe of each point
+#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
+
+// Use double touch for probing
+//#define PROBE_DOUBLE_TOUCH
+
+/**
+ * Z probes require clearance when deploying, stowing, and moving between
+ * probe points to avoid hitting the bed and other hardware.
+ * Servo-mounted probes require extra space for the arm to rotate.
+ * Inductive probes need space to keep from triggering early.
+ *
+ * Use these settings to specify the distance (mm) to raise the probe (or
+ * lower the bed). The values set here apply over and above any (negative)
+ * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
+ * Only integer values >= 1 are valid here.
+ *
+ * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
+ * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
+ */
+#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
+#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
+
+// For M851 give a range for adjusting the Z probe offset
+#define Z_PROBE_OFFSET_RANGE_MIN -20
+#define Z_PROBE_OFFSET_RANGE_MAX 20
+
+// Enable the M48 repeatability test to test probe accuracy
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
+// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
+// :{ 0:'Low', 1:'High' }
+#define X_ENABLE_ON 0
+#define Y_ENABLE_ON 0
+#define Z_ENABLE_ON 0
+#define E_ENABLE_ON 0 // For all extruders
+
+// Disables axis stepper immediately when it's not being used.
+// WARNING: When motors turn off there is a chance of losing position accuracy!
+#define DISABLE_X false
+#define DISABLE_Y false
+#define DISABLE_Z false
+// Warn on display about possibly reduced accuracy
+//#define DISABLE_REDUCED_ACCURACY_WARNING
+
+// @section extruder
+
+#define DISABLE_E false // For all extruders
+#define DISABLE_INACTIVE_EXTRUDER true // Keep only the active extruder enabled.
+
+// @section machine
+
+// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
+#define INVERT_X_DIR false
+#define INVERT_Y_DIR false
+#define INVERT_Z_DIR true
+
+// Enable this option for Toshiba stepper drivers
+//#define CONFIG_STEPPERS_TOSHIBA
+
+// @section extruder
+
+// For direct drive extruder v9 set to true, for geared extruder set to false.
+#define INVERT_E0_DIR false
+#define INVERT_E1_DIR false
+#define INVERT_E2_DIR false
+#define INVERT_E3_DIR false
+#define INVERT_E4_DIR false
+
+// @section homing
+
+//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+ // Be sure you have this distance over your Z_MAX_POS in case.
+
+// Direction of endstops when homing; 1=MAX, -1=MIN
+// :[-1,1]
+#define X_HOME_DIR -1
+#define Y_HOME_DIR -1
+#define Z_HOME_DIR -1
+
+// @section machine
+
+// Travel limits after homing (units are in mm)
+#define X_MIN_POS -33
+#define Y_MIN_POS -10
+#define Z_MIN_POS 0
+#define X_MAX_POS 220
+#define Y_MAX_POS 220
+#define Z_MAX_POS 240
+
+// If enabled, axes won't move below MIN_POS in response to movement commands.
+#define MIN_SOFTWARE_ENDSTOPS
+// If enabled, axes won't move above MAX_POS in response to movement commands.
+#define MAX_SOFTWARE_ENDSTOPS
+
+/**
+ * Filament Runout Sensor
+ * A mechanical or opto endstop is used to check for the presence of filament.
+ *
+ * RAMPS-based boards use SERVO3_PIN.
+ * For other boards you may need to define FIL_RUNOUT_PIN.
+ * By default the firmware assumes HIGH = has filament, LOW = ran out
+ */
+//#define FILAMENT_RUNOUT_SENSOR
+#if ENABLED(FILAMENT_RUNOUT_SENSOR)
+ #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
+ #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
+ #define FILAMENT_RUNOUT_SCRIPT "M600"
+#endif
+
+//===========================================================================
+//=============================== Bed Leveling ==============================
+//===========================================================================
+// @section bedlevel
+
+/**
+ * Choose one of the options below to enable G29 Bed Leveling. The parameters
+ * and behavior of G29 will change depending on your selection.
+ *
+ * If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
+ *
+ * - AUTO_BED_LEVELING_3POINT
+ * Probe 3 arbitrary points on the bed (that aren't collinear)
+ * You specify the XY coordinates of all 3 points.
+ * The result is a single tilted plane. Best for a flat bed.
+ *
+ * - AUTO_BED_LEVELING_LINEAR
+ * Probe several points in a grid.
+ * You specify the rectangle and the density of sample points.
+ * The result is a single tilted plane. Best for a flat bed.
+ *
+ * - AUTO_BED_LEVELING_BILINEAR
+ * Probe several points in a grid.
+ * You specify the rectangle and the density of sample points.
+ * The result is a mesh, best for large or uneven beds.
+ *
+ * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
+ * A comprehensive bed leveling system combining the features and benefits
+ * of other systems. UBL also includes integrated Mesh Generation, Mesh
+ * Validation and Mesh Editing systems. Currently, UBL is only checked out
+ * for Cartesian Printers. That said, it was primarily designed to correct
+ * poor quality Delta Printers. If you feel adventurous and have a Delta,
+ * please post an issue if something doesn't work correctly. Initially,
+ * you will need to set a reduced bed size so you have a rectangular area
+ * to test on.
+ *
+ * - MESH_BED_LEVELING
+ * Probe a grid manually
+ * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
+ * For machines without a probe, Mesh Bed Leveling provides a method to perform
+ * leveling in steps so you can manually adjust the Z height at each grid-point.
+ * With an LCD controller the process is guided step-by-step.
+ */
+//#define AUTO_BED_LEVELING_3POINT
+//#define AUTO_BED_LEVELING_LINEAR
+//#define AUTO_BED_LEVELING_BILINEAR
+//#define AUTO_BED_LEVELING_UBL
+//#define MESH_BED_LEVELING
+
+/**
+ * Enable detailed logging of G28, G29, M48, etc.
+ * Turn on with the command 'M111 S32'.
+ * NOTE: Requires a lot of PROGMEM!
+ */
+//#define DEBUG_LEVELING_FEATURE
+
+#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
+ // Gradually reduce leveling correction until a set height is reached,
+ // at which point movement will be level to the machine's XY plane.
+ // The height can be set with M420 Z
+ #define ENABLE_LEVELING_FADE_HEIGHT
+#endif
+
+#if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)
+
+ // Set the number of grid points per dimension.
+ #define GRID_MAX_POINTS_X 3
+ #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
+
+ // Set the boundaries for probing (where the probe can reach).
+ #define LEFT_PROBE_BED_POSITION 15
+ #define RIGHT_PROBE_BED_POSITION 190
+ #define FRONT_PROBE_BED_POSITION 15
+ #define BACK_PROBE_BED_POSITION 170
+
+ // The Z probe minimum outer margin (to validate G29 parameters).
+ #define MIN_PROBE_EDGE 10
+
+ // Probe along the Y axis, advancing X after each column
+ //#define PROBE_Y_FIRST
+
+ #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
+
+ // Beyond the probed grid, continue the implied tilt?
+ // Default is to maintain the height of the nearest edge.
+ //#define EXTRAPOLATE_BEYOND_GRID
+
+ //
+ // Experimental Subdivision of the grid by Catmull-Rom method.
+ // Synthesizes intermediate points to produce a more detailed mesh.
+ //
+ //#define ABL_BILINEAR_SUBDIVISION
+ #if ENABLED(ABL_BILINEAR_SUBDIVISION)
+ // Number of subdivisions between probe points
+ #define BILINEAR_SUBDIVISIONS 3
+ #endif
+
+ #endif
+
+#elif ENABLED(AUTO_BED_LEVELING_3POINT)
+
+ // 3 arbitrary points to probe.
+ // A simple cross-product is used to estimate the plane of the bed.
+ #define ABL_PROBE_PT_1_X 20
+ #define ABL_PROBE_PT_1_Y 160
+ #define ABL_PROBE_PT_2_X 20
+ #define ABL_PROBE_PT_2_Y 10
+ #define ABL_PROBE_PT_3_X 180
+ #define ABL_PROBE_PT_3_Y 10
+
+#elif ENABLED(AUTO_BED_LEVELING_UBL)
+
+ //===========================================================================
+ //========================= Unified Bed Leveling ============================
+ //===========================================================================
+
+ #define UBL_MESH_INSET 1 // Mesh inset margin on print area
+ #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
+ #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
+
+ #define UBL_PROBE_PT_1_X 39 // Probing points for 3-Point leveling of the mesh
+ #define UBL_PROBE_PT_1_Y 180
+ #define UBL_PROBE_PT_2_X 39
+ #define UBL_PROBE_PT_2_Y 20
+ #define UBL_PROBE_PT_3_X 180
+ #define UBL_PROBE_PT_3_Y 20
+
+ #define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation
+ #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
+
+#elif ENABLED(MESH_BED_LEVELING)
+
+ //===========================================================================
+ //=================================== Mesh ==================================
+ //===========================================================================
+
+ #define MESH_INSET 10 // Mesh inset margin on print area
+ #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
+ #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
+
+ //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
+
+#endif // BED_LEVELING
+
+/**
+ * Use the LCD controller for bed leveling
+ * Requires MESH_BED_LEVELING or PROBE_MANUALLY
+ */
+//#define LCD_BED_LEVELING
+
+#if ENABLED(LCD_BED_LEVELING)
+ #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
+ #define LCD_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
+#endif
+
+/**
+ * Commands to execute at the end of G29 probing.
+ * Useful to retract or move the Z probe out of the way.
+ */
+//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
+
+
+// @section homing
+
+// The center of the bed is at (X=0, Y=0)
+//#define BED_CENTER_AT_0_0
+
+// Manually set the home position. Leave these undefined for automatic settings.
+// For DELTA this is the top-center of the Cartesian print volume.
+//#define MANUAL_X_HOME_POS 0
+//#define MANUAL_Y_HOME_POS 0
+//#define MANUAL_Z_HOME_POS 0
+
+// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
+//
+// With this feature enabled:
+//
+// - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
+// - If stepper drivers time out, it will need X and Y homing again before Z homing.
+// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
+// - Prevent Z homing when the Z probe is outside bed area.
+//#define Z_SAFE_HOMING
+
+#if ENABLED(Z_SAFE_HOMING)
+ #define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2) // X point for Z homing when homing all axis (G28).
+ #define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28).
+#endif
+
+// Homing speeds (mm/m)
+#define HOMING_FEEDRATE_XY (100*60)
+#define HOMING_FEEDRATE_Z (4*60)
+
+//=============================================================================
+//============================= Additional Features ===========================
+//=============================================================================
+
+// @section extras
+
+//
+// EEPROM
+//
+// The microcontroller can store settings in the EEPROM, e.g. max velocity...
+// M500 - stores parameters in EEPROM
+// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
+// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
+//define this to enable EEPROM support
+#define EEPROM_SETTINGS
+
+#if ENABLED(EEPROM_SETTINGS)
+ // To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
+ #define EEPROM_CHITCHAT // Please keep turned on if you can.
+#endif
+
+//
+// Host Keepalive
+//
+// When enabled Marlin will send a busy status message to the host
+// every couple of seconds when it can't accept commands.
+//
+//#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
+//#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
+
+//
+// M100 Free Memory Watcher
+//
+//#define M100_FREE_MEMORY_WATCHER // uncomment to add the M100 Free Memory Watcher for debug purpose
+
+//
+// G20/G21 Inch mode support
+//
+//#define INCH_MODE_SUPPORT
+
+//
+// M149 Set temperature units support
+//
+//#define TEMPERATURE_UNITS_SUPPORT
+
+// @section temperature
+
+// Preheat Constants
+#define PREHEAT_1_TEMP_HOTEND 190
+#define PREHEAT_1_TEMP_BED 60
+#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
+
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED 90
+#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
+
+/**
+ * Nozzle Park -- EXPERIMENTAL
+ *
+ * Park the nozzle at the given XYZ position on idle or G27.
+ *
+ * The "P" parameter controls the action applied to the Z axis:
+ *
+ * P0 (Default) If Z is below park Z raise the nozzle.
+ * P1 Raise the nozzle always to Z-park height.
+ * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
+ */
+//#define NOZZLE_PARK_FEATURE
+
+#if ENABLED(NOZZLE_PARK_FEATURE)
+ // Specify a park position as { X, Y, Z }
+ #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
+#endif
+
+/**
+ * Clean Nozzle Feature -- EXPERIMENTAL
+ *
+ * Adds the G12 command to perform a nozzle cleaning process.
+ *
+ * Parameters:
+ * P Pattern
+ * S Strokes / Repetitions
+ * T Triangles (P1 only)
+ *
+ * Patterns:
+ * P0 Straight line (default). This process requires a sponge type material
+ * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
+ * between the start / end points.
+ *
+ * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
+ * number of zig-zag triangles to do. "S" defines the number of strokes.
+ * Zig-zags are done in whichever is the narrower dimension.
+ * For example, "G12 P1 S1 T3" will execute:
+ *
+ * --
+ * | (X0, Y1) | /\ /\ /\ | (X1, Y1)
+ * | | / \ / \ / \ |
+ * A | | / \ / \ / \ |
+ * | | / \ / \ / \ |
+ * | (X0, Y0) | / \/ \/ \ | (X1, Y0)
+ * -- +--------------------------------+
+ * |________|_________|_________|
+ * T1 T2 T3
+ *
+ * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
+ * "R" specifies the radius. "S" specifies the stroke count.
+ * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
+ *
+ * Caveats: The ending Z should be the same as starting Z.
+ * Attention: EXPERIMENTAL. G-code arguments may change.
+ *
+ */
+//#define NOZZLE_CLEAN_FEATURE
+
+#if ENABLED(NOZZLE_CLEAN_FEATURE)
+ // Default number of pattern repetitions
+ #define NOZZLE_CLEAN_STROKES 12
+
+ // Default number of triangles
+ #define NOZZLE_CLEAN_TRIANGLES 3
+
+ // Specify positions as { X, Y, Z }
+ #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
+ #define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)}
+
+ // Circular pattern radius
+ #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+ // Circular pattern circle fragments number
+ #define NOZZLE_CLEAN_CIRCLE_FN 10
+ // Middle point of circle
+ #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
+ // Moves the nozzle to the initial position
+ #define NOZZLE_CLEAN_GOBACK
+#endif
+
+/**
+ * Print Job Timer
+ *
+ * Automatically start and stop the print job timer on M104/M109/M190.
+ *
+ * M104 (hotend, no wait) - high temp = none, low temp = stop timer
+ * M109 (hotend, wait) - high temp = start timer, low temp = stop timer
+ * M190 (bed, wait) - high temp = start timer, low temp = none
+ *
+ * The timer can also be controlled with the following commands:
+ *
+ * M75 - Start the print job timer
+ * M76 - Pause the print job timer
+ * M77 - Stop the print job timer
+ */
+#define PRINTJOB_TIMER_AUTOSTART
+
+/**
+ * Print Counter
+ *
+ * Track statistical data such as:
+ *
+ * - Total print jobs
+ * - Total successful print jobs
+ * - Total failed print jobs
+ * - Total time printing
+ *
+ * View the current statistics with M78.
+ */
+//#define PRINTCOUNTER
+
+//=============================================================================
+//============================= LCD and SD support ============================
+//=============================================================================
+
+// @section lcd
+
+/**
+ * LCD LANGUAGE
+ *
+ * Select the language to display on the LCD. These languages are available:
+ *
+ * en, an, bg, ca, cn, cz, de, el, el-gr, es, eu, fi, fr, gl, hr, it,
+ * kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, tr, uk, test
+ *
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'tr':'Turkish', 'uk':'Ukrainian', 'test':'TEST' }
+ */
+#define LCD_LANGUAGE en
+
+/**
+ * LCD Character Set
+ *
+ * Note: This option is NOT applicable to Graphical Displays.
+ *
+ * All character-based LCDs provide ASCII plus one of these
+ * language extensions:
+ *
+ * - JAPANESE ... the most common
+ * - WESTERN ... with more accented characters
+ * - CYRILLIC ... for the Russian language
+ *
+ * To determine the language extension installed on your controller:
+ *
+ * - Compile and upload with LCD_LANGUAGE set to 'test'
+ * - Click the controller to view the LCD menu
+ * - The LCD will display Japanese, Western, or Cyrillic text
+ *
+ * See https://github.com/MarlinFirmware/Marlin/wiki/LCD-Language
+ *
+ * :['JAPANESE', 'WESTERN', 'CYRILLIC']
+ */
+#define DISPLAY_CHARSET_HD44780 JAPANESE
+
+/**
+ * LCD TYPE
+ *
+ * Enable ULTRA_LCD for a 16x2, 16x4, 20x2, or 20x4 character-based LCD.
+ * Enable DOGLCD for a 128x64 (ST7565R) Full Graphical Display.
+ * (These options will be enabled automatically for most displays.)
+ *
+ * IMPORTANT: The U8glib library is required for Full Graphic Display!
+ * https://github.com/olikraus/U8glib_Arduino
+ */
+//#define ULTRA_LCD // Character based
+//#define DOGLCD // Full graphics display
+
+/**
+ * SD CARD
+ *
+ * SD Card support is disabled by default. If your controller has an SD slot,
+ * you must uncomment the following option or it won't work.
+ *
+ */
+#define SDSUPPORT
+
+/**
+ * SD CARD: SPI SPEED
+ *
+ * Enable one of the following items for a slower SPI transfer speed.
+ * This may be required to resolve "volume init" errors.
+ */
+//#define SPI_SPEED SPI_HALF_SPEED
+//#define SPI_SPEED SPI_QUARTER_SPEED
+//#define SPI_SPEED SPI_EIGHTH_SPEED
+
+/**
+ * SD CARD: ENABLE CRC
+ *
+ * Use CRC checks and retries on the SD communication.
+ */
+//#define SD_CHECK_AND_RETRY
+
+//
+// ENCODER SETTINGS
+//
+// This option overrides the default number of encoder pulses needed to
+// produce one step. Should be increased for high-resolution encoders.
+//
+//#define ENCODER_PULSES_PER_STEP 1
+
+//
+// Use this option to override the number of step signals required to
+// move between next/prev menu items.
+//
+//#define ENCODER_STEPS_PER_MENU_ITEM 5
+
+/**
+ * Encoder Direction Options
+ *
+ * Test your encoder's behavior first with both options disabled.
+ *
+ * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
+ * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
+ * Reversed Value Editing only? Enable BOTH options.
+ */
+
+//
+// This option reverses the encoder direction everywhere.
+//
+// Set this option if CLOCKWISE causes values to DECREASE
+//
+//#define REVERSE_ENCODER_DIRECTION
+
+//
+// This option reverses the encoder direction for navigating LCD menus.
+//
+// If CLOCKWISE normally moves DOWN this makes it go UP.
+// If CLOCKWISE normally moves UP this makes it go DOWN.
+//
+//#define REVERSE_MENU_DIRECTION
+
+//
+// Individual Axis Homing
+//
+// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
+//
+//#define INDIVIDUAL_AXIS_HOMING_MENU
+
+//
+// SPEAKER/BUZZER
+//
+// If you have a speaker that can produce tones, enable it here.
+// By default Marlin assumes you have a buzzer with a fixed frequency.
+//
+//#define SPEAKER
+
+//
+// The duration and frequency for the UI feedback sound.
+// Set these to 0 to disable audio feedback in the LCD menus.
+//
+// Note: Test audio output with the G-Code:
+// M300 S P
+//
+//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
+//#define LCD_FEEDBACK_FREQUENCY_HZ 1000
+
+//
+// CONTROLLER TYPE: Standard
+//
+// Marlin supports a wide variety of controllers.
+// Enable one of the following options to specify your controller.
+//
+
+//
+// ULTIMAKER Controller.
+//
+//#define ULTIMAKERCONTROLLER
+
+//
+// ULTIPANEL as seen on Thingiverse.
+//
+//#define ULTIPANEL
+
+//
+// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
+// http://reprap.org/wiki/PanelOne
+//
+//#define PANEL_ONE
+
+//
+// MaKr3d Makr-Panel with graphic controller and SD support.
+// http://reprap.org/wiki/MaKr3d_MaKrPanel
+//
+//#define MAKRPANEL
+
+//
+// ReprapWorld Graphical LCD
+// https://reprapworld.com/?products_details&products_id/1218
+//
+//#define REPRAPWORLD_GRAPHICAL_LCD
+
+//
+// Activate one of these if you have a Panucatt Devices
+// Viki 2.0 or mini Viki with Graphic LCD
+// http://panucatt.com
+//
+//#define VIKI2
+//#define miniVIKI
+
+//
+// Adafruit ST7565 Full Graphic Controller.
+// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
+//
+//#define ELB_FULL_GRAPHIC_CONTROLLER
+
+//
+// RepRapDiscount Smart Controller.
+// http://reprap.org/wiki/RepRapDiscount_Smart_Controller
+//
+// Note: Usually sold with a white PCB.
+//
+//#define REPRAP_DISCOUNT_SMART_CONTROLLER
+
+//
+// GADGETS3D G3D LCD/SD Controller
+// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
+//
+// Note: Usually sold with a blue PCB.
+//
+//#define G3D_PANEL
+
+//
+// RepRapDiscount FULL GRAPHIC Smart Controller
+// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
+//
+// Note: Details on connecting to the Anet V1.0 controller are in the file pins_ANET_10.h
+//
+//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+
+//
+// MakerLab Mini Panel with graphic
+// controller and SD support - http://reprap.org/wiki/Mini_panel
+//
+//#define MINIPANEL
+
+//
+// RepRapWorld REPRAPWORLD_KEYPAD v1.1
+// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
+//
+// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key
+// is pressed, a value of 10.0 means 10mm per click.
+//
+//#define REPRAPWORLD_KEYPAD
+//#define REPRAPWORLD_KEYPAD_MOVE_STEP 1.0
+
+//
+// RigidBot Panel V1.0
+// http://www.inventapart.com/
+//
+//#define RIGIDBOT_PANEL
+
+//
+// BQ LCD Smart Controller shipped by
+// default with the BQ Hephestos 2 and Witbox 2.
+//
+//#define BQ_LCD_SMART_CONTROLLER
+
+//
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// ANET_10 Controller supported displays.
+//
+#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
+//
+// CONTROLLER TYPE: I2C
+//
+// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
+// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
+//
+
+//
+// Elefu RA Board Control Panel
+// http://www.elefu.com/index.php?route=product/product&product_id=53
+//
+//#define RA_CONTROL_PANEL
+
+//
+// Sainsmart YW Robot (LCM1602) LCD Display
+//
+//#define LCD_I2C_SAINSMART_YWROBOT
+
+//
+// Generic LCM1602 LCD adapter
+//
+//#define LCM1602
+
+//
+// PANELOLU2 LCD with status LEDs,
+// separate encoder and click inputs.
+//
+// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
+// For more info: https://github.com/lincomatic/LiquidTWI2
+//
+// Note: The PANELOLU2 encoder click input can either be directly connected to
+// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
+//
+//#define LCD_I2C_PANELOLU2
+
+//
+// Panucatt VIKI LCD with status LEDs,
+// integrated click & L/R/U/D buttons, separate encoder inputs.
+//
+//#define LCD_I2C_VIKI
+
+//
+// SSD1306 OLED full graphics generic display
+//
+//#define U8GLIB_SSD1306
+
+//
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
+// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
+//
+//#define SAV_3DGLCD
+#if ENABLED(SAV_3DGLCD)
+ //#define U8GLIB_SSD1306
+ #define U8GLIB_SH1106
+#endif
+
+//
+// CONTROLLER TYPE: Shift register panels
+//
+// 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH
+// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
+//
+//#define SAV_3DLCD
+
+//=============================================================================
+//=============================== Extra Features ==============================
+//=============================================================================
+
+// @section extras
+
+// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
+//#define FAST_PWM_FAN
+
+// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
+// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
+// is too low, you should also increment SOFT_PWM_SCALE.
+//#define FAN_SOFT_PWM
+
+// Incrementing this by 1 will double the software PWM frequency,
+// affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
+// However, control resolution will be halved for each increment;
+// at zero value, there are 128 effective control positions.
+#define SOFT_PWM_SCALE 0
+
+// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
+// be used to mitigate the associated resolution loss. If enabled,
+// some of the PWM cycles are stretched so on average the desired
+// duty cycle is attained.
+//#define SOFT_PWM_DITHER
+
+// Temperature status LEDs that display the hotend and bed temperature.
+// If all hotends, bed temperature, and target temperature are under 54C
+// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
+//#define TEMP_STAT_LEDS
+
+// M240 Triggers a camera by emulating a Canon RC-1 Remote
+// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
+//#define PHOTOGRAPH_PIN 23
+
+// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
+//#define SF_ARC_FIX
+
+// Support for the BariCUDA Paste Extruder.
+//#define BARICUDA
+
+//define BlinkM/CyzRgb Support
+//#define BLINKM
+
+//define PCA9632 PWM LED driver Support
+//#define PCA9632
+
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ *
+ * *** CAUTION ***
+ * LED Strips require a MOFSET Chip between PWM lines and LEDs,
+ * as the Arduino cannot handle the current the LEDs will require.
+ * Failure to follow this precaution can destroy your Arduino!
+ * *** CAUTION ***
+ *
+ */
+//#define RGB_LED
+//#define RGBW_LED
+#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
+ #define RGB_LED_R_PIN 34
+ #define RGB_LED_G_PIN 43
+ #define RGB_LED_B_PIN 35
+ #define RGB_LED_W_PIN -1
+#endif
+
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ * - Gradually change from blue to violet as the heated bed gets to target temp
+ * - Gradually change from violet to red as the hotend gets to temperature
+ * - Change to white to illuminate work surface
+ * - Change to green once print has finished
+ * - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632)
+ #define PRINTER_EVENT_LEDS
+#endif
+
+/*********************************************************************\
+* R/C SERVO support
+* Sponsored by TrinityLabs, Reworked by codexmas
+**********************************************************************/
+
+// Number of servos
+//
+// If you select a configuration below, this will receive a default value and does not need to be set manually
+// set it manually if you have more servos than extruders and wish to manually control some
+// leaving it undefined or defining as 0 will disable the servo subsystem
+// If unsure, leave commented / disabled
+//
+//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
+
+// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// 300ms is a good value but you can try less delay.
+// If the servo can't reach the requested position, increase it.
+#define SERVO_DELAY 300
+
+// Servo deactivation
+//
+// With this option servos are powered only during movement, then turned off to prevent jitter.
+//#define DEACTIVATE_SERVOS_AFTER_MOVE
+
+/**
+ * Filament Width Sensor
+ *
+ * Measures the filament width in real-time and adjusts
+ * flow rate to compensate for any irregularities.
+ *
+ * Also allows the measured filament diameter to set the
+ * extrusion rate, so the slicer only has to specify the
+ * volume.
+ *
+ * Only a single extruder is supported at this time.
+ *
+ * 34 RAMPS_14 : Analog input 5 on the AUX2 connector
+ * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 RAMBO : Analog input 3
+ *
+ * Note: May require analog pins to be defined for other boards.
+ */
+//#define FILAMENT_WIDTH_SENSOR
+
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+ #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
+ #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
+
+ #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
+ #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
+ #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
+
+ #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
+
+ // Display filament width on the LCD status line. Status messages will expire after 5 seconds.
+ //#define FILAMENT_LCD_DISPLAY
+#endif
+
+#endif // CONFIGURATION_H
diff --git a/Marlin/example_configurations/Anet/Configuration_adv.h b/Marlin/example_configurations/Anet/Configuration_adv.h
new file mode 100644
index 000000000..d41f1d208
--- /dev/null
+++ b/Marlin/example_configurations/Anet/Configuration_adv.h
@@ -0,0 +1,1349 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see .
+ *
+ */
+
+/**
+ * Configuration_adv.h
+ *
+ * Advanced settings.
+ * Only change these if you know exactly what you're doing.
+ * Some of these settings can damage your printer if improperly set!
+ *
+ * Basic settings can be found in Configuration.h
+ *
+ */
+#ifndef CONFIGURATION_ADV_H
+#define CONFIGURATION_ADV_H
+#define CONFIGURATION_ADV_H_VERSION 010100
+
+// @section temperature
+
+//===========================================================================
+//=============================Thermal Settings ============================
+//===========================================================================
+
+#if DISABLED(PIDTEMPBED)
+ #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
+ #if ENABLED(BED_LIMIT_SWITCHING)
+ #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
+ #endif
+#endif
+
+/**
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * The solution: Once the temperature reaches the target, start observing.
+ * If the temperature stays too far below the target (hysteresis) for too long (period),
+ * the firmware will halt the machine as a safety precaution.
+ *
+ * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
+ */
+#if ENABLED(THERMAL_PROTECTION_HOTENDS)
+ #define THERMAL_PROTECTION_PERIOD 60 // Seconds
+ #define THERMAL_PROTECTION_HYSTERESIS 10 // Degrees Celsius
+
+ /**
+ * Whenever an M104 or M109 increases the target temperature the firmware will wait for the
+ * WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
+ * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
+ * but only if the current temperature is far enough below the target for a reliable test.
+ *
+ * If you get false positives for "Heating failed" increase WATCH_TEMP_PERIOD and/or decrease WATCH_TEMP_INCREASE
+ * WATCH_TEMP_INCREASE should not be below 2.
+ */
+ #define WATCH_TEMP_PERIOD 20 // Seconds
+ #define WATCH_TEMP_INCREASE 2 // Degrees Celsius
+#endif
+
+/**
+ * Thermal Protection parameters for the bed are just as above for hotends.
+ */
+#if ENABLED(THERMAL_PROTECTION_BED)
+ #define THERMAL_PROTECTION_BED_PERIOD 60 // Seconds
+ #define THERMAL_PROTECTION_BED_HYSTERESIS 5 // Degrees Celsius
+
+ /**
+ * Whenever an M140 or M190 increases the target temperature the firmware will wait for the
+ * WATCH_BED_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_BED_TEMP_INCREASE
+ * degrees, the machine is halted, requiring a hard reset. This test restarts with any M140/M190,
+ * but only if the current temperature is far enough below the target for a reliable test.
+ *
+ * If you get too many "Heating failed" errors, increase WATCH_BED_TEMP_PERIOD and/or decrease
+ * WATCH_BED_TEMP_INCREASE. (WATCH_BED_TEMP_INCREASE should not be below 2.)
+ */
+ #define WATCH_BED_TEMP_PERIOD 180 // Seconds
+ #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
+#endif
+
+#if ENABLED(PIDTEMP)
+ // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
+ // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ //#define PID_EXTRUSION_SCALING
+ #if ENABLED(PID_EXTRUSION_SCALING)
+ #define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
+ #define LPQ_MAX_LEN 50
+ #endif
+#endif
+
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S B F
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by executing M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
+//#define AUTOTEMP
+#if ENABLED(AUTOTEMP)
+ #define AUTOTEMP_OLDWEIGHT 0.98
+#endif
+
+// Show Temperature ADC value
+// Enable for M105 to include ADC values read from temperature sensors.
+//#define SHOW_TEMP_ADC_VALUES
+
+/**
+ * High Temperature Thermistor Support
+ *
+ * Thermistors able to support high temperature tend to have a hard time getting
+ * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP
+ * will probably be caught when the heating element first turns on during the
+ * preheating process, which will trigger a min_temp_error as a safety measure
+ * and force stop everything.
+ * To circumvent this limitation, we allow for a preheat time (during which,
+ * min_temp_error won't be triggered) and add a min_temp buffer to handle
+ * aberrant readings.
+ *
+ * If you want to enable this feature for your hotend thermistor(s)
+ * uncomment and set values > 0 in the constants below
+ */
+
+// The number of consecutive low temperature errors that can occur
+// before a min_temp_error is triggered. (Shouldn't be more than 10.)
+//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0
+
+// The number of milliseconds a hotend will preheat before starting to check
+// the temperature. This value should NOT be set to the time it takes the
+// hot end to reach the target temperature, but the time it takes to reach
+// the minimum temperature your thermistor can read. The lower the better/safer.
+// This shouldn't need to be more than 30 seconds (30000)
+//#define MILLISECONDS_PREHEAT_TIME 0
+
+// @section extruder
+
+// Extruder runout prevention.
+// If the machine is idle and the temperature over MINTEMP
+// then extrude some filament every couple of SECONDS.
+//#define EXTRUDER_RUNOUT_PREVENT
+#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
+ #define EXTRUDER_RUNOUT_MINTEMP 190
+ #define EXTRUDER_RUNOUT_SECONDS 30
+ #define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
+ #define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
+#endif
+
+// @section temperature
+
+//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
+//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
+#define TEMP_SENSOR_AD595_OFFSET 0.0
+#define TEMP_SENSOR_AD595_GAIN 1.0
+
+/**
+ * Controller Fan
+ * To cool down the stepper drivers and MOSFETs.
+ *
+ * The fan will turn on automatically whenever any stepper is enabled
+ * and turn off after a set period after all steppers are turned off.
+ */
+//#define USE_CONTROLLER_FAN
+#if ENABLED(USE_CONTROLLER_FAN)
+ //#define CONTROLLER_FAN_PIN FAN1_PIN // Set a custom pin for the controller fan
+ #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled
+ #define CONTROLLERFAN_SPEED 255 // 255 == full speed
+#endif
+
+// When first starting the main fan, run it at full speed for the
+// given number of milliseconds. This gets the fan spinning reliably
+// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
+//#define FAN_KICKSTART_TIME 100
+
+// This defines the minimal speed for the main fan, run in PWM mode
+// to enable uncomment and set minimal PWM speed for reliable running (1-255)
+// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+//#define FAN_MIN_PWM 50
+
+// @section extruder
+
+/**
+ * Extruder cooling fans
+ *
+ * Extruder auto fans automatically turn on when their extruders'
+ * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE.
+ *
+ * Your board's pins file specifies the recommended pins. Override those here
+ * or set to -1 to disable completely.
+ *
+ * Multiple extruders can be assigned to the same pin in which case
+ * the fan will turn on when any selected extruder is above the threshold.
+ */
+#define E0_AUTO_FAN_PIN -1
+#define E1_AUTO_FAN_PIN -1
+#define E2_AUTO_FAN_PIN -1
+#define E3_AUTO_FAN_PIN -1
+#define E4_AUTO_FAN_PIN -1
+#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
+#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
+
+/**
+ * M355 Case Light on-off / brightness
+ */
+//#define CASE_LIGHT_ENABLE
+#if ENABLED(CASE_LIGHT_ENABLE)
+ #define CASE_LIGHT_PIN 4 // can be defined here or in the pins_XXX.h file for your board
+ // pins_XXX.h file overrides this one
+ #define INVERT_CASE_LIGHT false // set to true if case light is ON when pin is at 0
+ #define CASE_LIGHT_DEFAULT_ON true // set default power up state to on or off
+ #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // set power up brightness 0-255 ( only used if on PWM
+ // and if CASE_LIGHT_DEFAULT is set to on
+ //#define MENU_ITEM_CASE_LIGHT // Uncomment to have a Case Light entry in main menu
+#endif
+
+//===========================================================================
+//============================ Mechanical Settings ==========================
+//===========================================================================
+
+// @section homing
+
+// If you want endstops to stay on (by default) even when not homing
+// enable this option. Override at any time with M120, M121.
+#define ENDSTOPS_ALWAYS_ON_DEFAULT
+
+// @section extras
+
+//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
+
+// Dual X Steppers
+// Uncomment this option to drive two X axis motors.
+// The next unused E driver will be assigned to the second X stepper.
+//#define X_DUAL_STEPPER_DRIVERS
+#if ENABLED(X_DUAL_STEPPER_DRIVERS)
+ // Set true if the two X motors need to rotate in opposite directions
+ #define INVERT_X2_VS_X_DIR true
+#endif
+
+// Dual Y Steppers
+// Uncomment this option to drive two Y axis motors.
+// The next unused E driver will be assigned to the second Y stepper.
+//#define Y_DUAL_STEPPER_DRIVERS
+#if ENABLED(Y_DUAL_STEPPER_DRIVERS)
+ // Set true if the two Y motors need to rotate in opposite directions
+ #define INVERT_Y2_VS_Y_DIR true
+#endif
+
+// A single Z stepper driver is usually used to drive 2 stepper motors.
+// Uncomment this option to use a separate stepper driver for each Z axis motor.
+// The next unused E driver will be assigned to the second Z stepper.
+//#define Z_DUAL_STEPPER_DRIVERS
+
+#if ENABLED(Z_DUAL_STEPPER_DRIVERS)
+
+ // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
+ // That way the machine is capable to align the bed during home, since both Z steppers are homed.
+ // There is also an implementation of M666 (software endstops adjustment) to this feature.
+ // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
+ // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
+ // If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
+ // Play a little bit with small adjustments (0.5mm) and check the behaviour.
+ // The M119 (endstops report) will start reporting the Z2 Endstop as well.
+
+ //#define Z_DUAL_ENDSTOPS
+
+ #if ENABLED(Z_DUAL_ENDSTOPS)
+ #define Z2_USE_ENDSTOP _XMAX_
+ #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine/test this value
+ #endif
+
+#endif // Z_DUAL_STEPPER_DRIVERS
+
+// Enable this for dual x-carriage printers.
+// A dual x-carriage design has the advantage that the inactive extruder can be parked which
+// prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage
+// allowing faster printing speeds. Connect your X2 stepper to the first unused E plug.
+//#define DUAL_X_CARRIAGE
+#if ENABLED(DUAL_X_CARRIAGE)
+ // Configuration for second X-carriage
+ // Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
+ // the second x-carriage always homes to the maximum endstop.
+ #define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
+ #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed
+ #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position
+ #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
+ // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software
+ // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
+ // without modifying the firmware (through the "M218 T1 X???" command).
+ // Remember: you should set the second extruder x-offset to 0 in your slicer.
+
+ // There are a few selectable movement modes for dual x-carriages using M605 S
+ // Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results
+ // as long as it supports dual x-carriages. (M605 S0)
+ // Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so
+ // that additional slicer support is not required. (M605 S1)
+ // Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all
+ // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at
+ // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
+
+ // This is the default power-up mode which can be later using M605.
+ #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE
+
+ // Default settings in "Auto-park Mode"
+ #define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder
+ #define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder
+
+ // Default x offset in duplication mode (typically set to half print bed width)
+ #define DEFAULT_DUPLICATION_X_OFFSET 100
+
+#endif // DUAL_X_CARRIAGE
+
+// Activate a solenoid on the active extruder with M380. Disable all with M381.
+// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
+//#define EXT_SOLENOID
+
+// @section homing
+
+//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+#define X_HOME_BUMP_MM 5
+#define Y_HOME_BUMP_MM 5
+#define Z_HOME_BUMP_MM 2
+#define HOMING_BUMP_DIVISOR {2, 2, 4} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
+//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
+
+// When G28 is called, this option will make Y home before X
+//#define HOME_Y_BEFORE_X
+
+// @section machine
+
+#define AXIS_RELATIVE_MODES {false, false, false, false}
+
+// Allow duplication mode with a basic dual-nozzle extruder
+//#define DUAL_NOZZLE_DUPLICATION_MODE
+
+// By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
+#define INVERT_X_STEP_PIN false
+#define INVERT_Y_STEP_PIN false
+#define INVERT_Z_STEP_PIN false
+#define INVERT_E_STEP_PIN false
+
+// Default stepper release if idle. Set to 0 to deactivate.
+// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
+// Time can be set by M18 and M84.
+#define DEFAULT_STEPPER_DEACTIVE_TIME 120
+#define DISABLE_INACTIVE_X true
+#define DISABLE_INACTIVE_Y true
+#define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_E true
+
+#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
+#define DEFAULT_MINTRAVELFEEDRATE 0.0
+
+//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated
+
+// @section lcd
+
+#if ENABLED(ULTIPANEL)
+ #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+ #define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
+#endif
+
+// @section extras
+
+// minimum time in microseconds that a movement needs to take if the buffer is emptied.
+#define DEFAULT_MINSEGMENTTIME 20000
+
+// If defined the movements slow down when the look ahead buffer is only half full
+#define SLOWDOWN
+
+// Frequency limit
+// See nophead's blog for more info
+// Not working O
+//#define XY_FREQUENCY_LIMIT 15
+
+// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
+// of the buffer and all stops. This should not be much greater than zero and should only be changed
+// if unwanted behavior is observed on a user's machine when running at very slow speeds.
+#define MINIMUM_PLANNER_SPEED 0.05// (mm/sec)
+
+// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
+#define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16]
+
+/**
+ * @section stepper motor current
+ *
+ * Some boards have a means of setting the stepper motor current via firmware.
+ *
+ * The power on motor currents are set by:
+ * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2
+ * known compatible chips: A4982
+ * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H
+ * known compatible chips: AD5206
+ * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
+ * known compatible chips: MCP4728
+ * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
+ * known compatible chips: MCP4451, MCP4018
+ *
+ * Motor currents can also be set by M907 - M910 and by the LCD.
+ * M907 - applies to all.
+ * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H
+ * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2
+ */
+//#define PWM_MOTOR_CURRENT {1300, 1300, 1250} // Values in milliamps
+//#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
+//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis
+
+// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
+//#define DIGIPOT_I2C
+//#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster
+#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
+// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
+#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0} // AZTEEG_X3_PRO
+
+//===========================================================================
+//=============================Additional Features===========================
+//===========================================================================
+
+#define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
+#define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
+#define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
+
+//#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
+#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
+
+// @section lcd
+
+// Include a page of printer information in the LCD Main Menu
+//#define LCD_INFO_MENU
+
+// Scroll a longer status message into view
+//#define STATUS_MESSAGE_SCROLLING
+
+// On the Info Screen, display XY with one decimal place when possible
+//#define LCD_DECIMAL_SMALL_XY
+
+// The timeout (in ms) to return to the status screen from sub-menus
+//#define LCD_TIMEOUT_TO_STATUS 15000
+
+#if ENABLED(SDSUPPORT)
+
+ // Some RAMPS and other boards don't detect when an SD card is inserted. You can work
+ // around this by connecting a push button or single throw switch to the pin defined
+ // as SD_DETECT_PIN in your board's pins definitions.
+ // This setting should be disabled unless you are using a push button, pulling the pin to ground.
+ // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
+ //#define SD_DETECT_INVERTED
+
+ #define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
+ #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+
+ #define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order.
+ // if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
+ // using:
+ //#define MENU_ADDAUTOSTART
+
+ /**
+ * Sort SD file listings in alphabetical order.
+ *
+ * With this option enabled, items on SD cards will be sorted
+ * by name for easier navigation.
+ *
+ * By default...
+ *
+ * - Use the slowest -but safest- method for sorting.
+ * - Folders are sorted to the top.
+ * - The sort key is statically allocated.
+ * - No added G-code (M34) support.
+ * - 40 item sorting limit. (Items after the first 40 are unsorted.)
+ *
+ * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the
+ * compiler to calculate the worst-case usage and throw an error if the SRAM
+ * limit is exceeded.
+ *
+ * - SDSORT_USES_RAM provides faster sorting via a static directory buffer.
+ * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer.
+ * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!)
+ * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!)
+ */
+ //#define SDCARD_SORT_ALPHA
+
+ // SD Card Sorting options
+ #if ENABLED(SDCARD_SORT_ALPHA)
+ #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256).
+ #define FOLDER_SORTING -1 // -1=above 0=none 1=below
+ #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code.
+ #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
+ #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
+ #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
+ #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
+ #endif
+
+ // Show a progress bar on HD44780 LCDs for SD printing
+ //#define LCD_PROGRESS_BAR
+
+ #if ENABLED(LCD_PROGRESS_BAR)
+ // Amount of time (ms) to show the bar
+ #define PROGRESS_BAR_BAR_TIME 2000
+ // Amount of time (ms) to show the status message
+ #define PROGRESS_BAR_MSG_TIME 3000
+ // Amount of time (ms) to retain the status message (0=forever)
+ #define PROGRESS_MSG_EXPIRE 0
+ // Enable this to show messages for MSG_TIME then hide them
+ //#define PROGRESS_MSG_ONCE
+ // Add a menu item to test the progress bar:
+ //#define LCD_PROGRESS_BAR_TEST
+ #endif
+
+ // This allows hosts to request long names for files and folders with M33
+ //#define LONG_FILENAME_HOST_SUPPORT
+
+ // This option allows you to abort SD printing when any endstop is triggered.
+ // This feature must be enabled with "M540 S1" or from the LCD menu.
+ // To have any effect, endstops must be enabled during SD printing.
+ //#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
+
+#endif // SDSUPPORT
+
+/**
+ * Additional options for Graphical Displays
+ *
+ * Use the optimizations here to improve printing performance,
+ * which can be adversely affected by graphical display drawing,
+ * especially when doing several short moves, and when printing
+ * on DELTA and SCARA machines.
+ *
+ * Some of these options may result in the display lagging behind
+ * controller events, as there is a trade-off between reliable
+ * printing performance versus fast display updates.
+ */
+#if ENABLED(DOGLCD)
+ // Enable to save many cycles by drawing a hollow frame on the Info Screen
+ #define XYZ_HOLLOW_FRAME
+
+ // Enable to save many cycles by drawing a hollow frame on Menu Screens
+ #define MENU_HOLLOW_FRAME
+
+ // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM.
+ // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
+ //#define USE_BIG_EDIT_FONT
+
+ // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM.
+ // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
+ //#define USE_SMALL_INFOFONT
+
+ // Enable this option and reduce the value to optimize screen updates.
+ // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
+ //#define DOGM_SPI_DELAY_US 5
+#endif // DOGLCD
+
+// @section safety
+
+// The hardware watchdog should reset the microcontroller disabling all outputs,
+// in case the firmware gets stuck and doesn't do temperature regulation.
+#define USE_WATCHDOG
+
+#if ENABLED(USE_WATCHDOG)
+ // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
+ // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
+ // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
+ //#define WATCHDOG_RESET_MANUAL
+#endif
+
+// @section lcd
+
+/**
+ * Babystepping enables movement of the axes by tiny increments without changing
+ * the current position values. This feature is used primarily to adjust the Z
+ * axis in the first layer of a print in real-time.
+ *
+ * Warning: Does not respect endstops!
+ */
+//#define BABYSTEPPING
+#if ENABLED(BABYSTEPPING)
+ #define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
+ #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
+ #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
+ //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+ //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
+ #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
+ // Note: Extra time may be added to mitigate controller latency.
+#endif
+
+// @section extruder
+
+// extruder advance constant (s2/mm3)
+//
+// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2
+//
+// Hooke's law says: force = k * distance
+// Bernoulli's principle says: v ^ 2 / 2 + g . h + pressure / density = constant
+// so: v ^ 2 is proportional to number of steps we advance the extruder
+//#define ADVANCE
+
+#if ENABLED(ADVANCE)
+ #define EXTRUDER_ADVANCE_K .0
+ #define D_FILAMENT 2.85
+#endif
+
+/**
+ * Implementation of linear pressure control
+ *
+ * Assumption: advance = k * (delta velocity)
+ * K=0 means advance disabled.
+ * See Marlin documentation for calibration instructions.
+ */
+//#define LIN_ADVANCE
+
+#if ENABLED(LIN_ADVANCE)
+ #define LIN_ADVANCE_K 75
+
+ /**
+ * Some Slicers produce Gcode with randomly jumping extrusion widths occasionally.
+ * For example within a 0.4mm perimeter it may produce a single segment of 0.05mm width.
+ * While this is harmless for normal printing (the fluid nature of the filament will
+ * close this very, very tiny gap), it throws off the LIN_ADVANCE pressure adaption.
+ *
+ * For this case LIN_ADVANCE_E_D_RATIO can be used to set the extrusion:distance ratio
+ * to a fixed value. Note that using a fixed ratio will lead to wrong nozzle pressures
+ * if the slicer is using variable widths or layer heights within one print!
+ *
+ * This option sets the default E:D ratio at startup. Use `M900` to override this value.
+ *
+ * Example: `M900 W0.4 H0.2 D1.75`, where:
+ * - W is the extrusion width in mm
+ * - H is the layer height in mm
+ * - D is the filament diameter in mm
+ *
+ * Example: `M900 R0.0458` to set the ratio directly.
+ *
+ * Set to 0 to auto-detect the ratio based on given Gcode G1 print moves.
+ *
+ * Slic3r (including Prusa Slic3r) produces Gcode compatible with the automatic mode.
+ * Cura (as of this writing) may produce Gcode incompatible with the automatic mode.
+ */
+ #define LIN_ADVANCE_E_D_RATIO 0 // The calculated ratio (or 0) according to the formula W * H / ((D / 2) ^ 2 * PI)
+ // Example: 0.4 * 0.2 / ((1.75 / 2) ^ 2 * PI) = 0.033260135
+#endif
+
+// @section leveling
+
+// Default mesh area is an area with an inset margin on the print area.
+// Below are the macros that are used to define the borders for the mesh area,
+// made available here for specialized needs, ie dual extruder setup.
+#if ENABLED(MESH_BED_LEVELING)
+ #define MESH_MIN_X (X_MIN_POS + MESH_INSET)
+ #define MESH_MAX_X (X_MAX_POS - (MESH_INSET))
+ #define MESH_MIN_Y (Y_MIN_POS + MESH_INSET)
+ #define MESH_MAX_Y (Y_MAX_POS - (MESH_INSET))
+#elif ENABLED(AUTO_BED_LEVELING_UBL)
+ #define UBL_MESH_MIN_X (X_MIN_POS + UBL_MESH_INSET)
+ #define UBL_MESH_MAX_X (X_MAX_POS - (UBL_MESH_INSET))
+ #define UBL_MESH_MIN_Y (Y_MIN_POS + UBL_MESH_INSET)
+ #define UBL_MESH_MAX_Y (Y_MAX_POS - (UBL_MESH_INSET))
+
+ // If this is defined, the currently active mesh will be saved in the
+ // current slot on M500.
+ #define UBL_SAVE_ACTIVE_ON_M500
+#endif
+
+// @section extras
+
+// Arc interpretation settings:
+//#define ARC_SUPPORT // Disabling this saves ~2738 bytes
+#define MM_PER_ARC_SEGMENT 1
+#define N_ARC_CORRECTION 25
+
+// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
+//#define BEZIER_CURVE_SUPPORT
+
+// G38.2 and G38.3 Probe Target
+// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
+//#define G38_PROBE_TARGET
+#if ENABLED(G38_PROBE_TARGET)
+ #define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
+#endif
+
+// Moves (or segments) with fewer steps than this will be joined with the next move
+#define MIN_STEPS_PER_SEGMENT 6
+
+// The minimum pulse width (in µs) for stepping a stepper.
+// Set this if you find stepping unreliable, or if using a very fast CPU.
+#define MINIMUM_STEPPER_PULSE 0 // (µs) The smallest stepper pulse allowed
+
+// @section temperature
+
+// Control heater 0 and heater 1 in parallel.
+//#define HEATERS_PARALLEL
+
+//===========================================================================
+//================================= Buffers =================================
+//===========================================================================
+
+// @section hidden
+
+// The number of linear motions that can be in the plan at any give time.
+// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
+#if ENABLED(SDSUPPORT)
+ #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
+#else
+ #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
+#endif
+
+// @section serial
+
+// The ASCII buffer for serial input
+#define MAX_CMD_SIZE 96
+#define BUFSIZE 4
+
+// Transfer Buffer Size
+// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
+// To buffer a simple "ok" you need 4 bytes.
+// For ADVANCED_OK (M105) you need 32 bytes.
+// For debug-echo: 128 bytes for the optimal speed.
+// Other output doesn't need to be that speedy.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256]
+#define TX_BUFFER_SIZE 0
+
+// Enable an emergency-command parser to intercept certain commands as they
+// enter the serial receive buffer, so they cannot be blocked.
+// Currently handles M108, M112, M410
+// Does not work on boards using AT90USB (USBCON) processors!
+//#define EMERGENCY_PARSER
+
+// Bad Serial-connections can miss a received command by sending an 'ok'
+// Therefore some clients abort after 30 seconds in a timeout.
+// Some other clients start sending commands while receiving a 'wait'.
+// This "wait" is only sent when the buffer is empty. 1 second is a good value here.
+//#define NO_TIMEOUTS 1000 // Milliseconds
+
+// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
+//#define ADVANCED_OK
+
+// @section fwretract
+
+// Firmware based and LCD controlled retract
+// M207 and M208 can be used to define parameters for the retraction.
+// The retraction can be called by the slicer using G10 and G11
+// until then, intended retractions can be detected by moves that only extrude and the direction.
+// the moves are than replaced by the firmware controlled ones.
+
+//#define FWRETRACT //ONLY PARTIALLY TESTED
+#if ENABLED(FWRETRACT)
+ #define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt
+ #define RETRACT_LENGTH 3 //default retract length (positive mm)
+ #define RETRACT_LENGTH_SWAP 13 //default swap retract length (positive mm), for extruder change
+ #define RETRACT_FEEDRATE 45 //default feedrate for retracting (mm/s)
+ #define RETRACT_ZLIFT 0 //default retract Z-lift
+ #define RETRACT_RECOVER_LENGTH 0 //default additional recover length (mm, added to retract length when recovering)
+ #define RETRACT_RECOVER_LENGTH_SWAP 0 //default additional swap recover length (mm, added to retract length when recovering from extruder change)
+ #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
+#endif
+
+/**
+ * Advanced Pause
+ * Experimental feature for filament change support and for parking the nozzle when paused.
+ * Adds the GCode M600 for initiating filament change.
+ * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle.
+ *
+ * Requires an LCD display.
+ * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
+ */
+//#define ADVANCED_PAUSE_FEATURE
+#if ENABLED(ADVANCED_PAUSE_FEATURE)
+ #define PAUSE_PARK_X_POS 3 // X position of hotend
+ #define PAUSE_PARK_Y_POS 3 // Y position of hotend
+ #define PAUSE_PARK_Z_ADD 10 // Z addition of hotend (lift)
+ #define PAUSE_PARK_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+ #define PAUSE_PARK_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
+ #define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
+ #define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
+ // It is a short retract used immediately after print interrupt before move to filament exchange position
+ #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
+ #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
+ // Longer length for bowden printers to unload filament from whole bowden tube,
+ // shorter length for printers without bowden to unload filament from extruder only,
+ // 0 to disable unloading for manual unloading
+ #define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+ #define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
+ // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
+ // Short or zero length for printers without bowden where loading is not used
+ #define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
+ #define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
+ // 0 to disable for manual extrusion
+ // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+ // or until outcoming filament color is not clear for filament color change
+ #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
+ #define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
+ #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
+ // even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
+ //#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
+#endif
+
+// @section tmc
+
+/**
+ * Enable this section if you have TMC26X motor drivers.
+ * You will need to import the TMC26XStepper library into the Arduino IDE for this
+ * (https://github.com/trinamic/TMC26XStepper.git)
+ */
+//#define HAVE_TMCDRIVER
+
+#if ENABLED(HAVE_TMCDRIVER)
+
+ //#define X_IS_TMC
+ //#define X2_IS_TMC
+ //#define Y_IS_TMC
+ //#define Y2_IS_TMC
+ //#define Z_IS_TMC
+ //#define Z2_IS_TMC
+ //#define E0_IS_TMC
+ //#define E1_IS_TMC
+ //#define E2_IS_TMC
+ //#define E3_IS_TMC
+ //#define E4_IS_TMC
+
+ #define X_MAX_CURRENT 1000 // in mA
+ #define X_SENSE_RESISTOR 91 // in mOhms
+ #define X_MICROSTEPS 16 // number of microsteps
+
+ #define X2_MAX_CURRENT 1000
+ #define X2_SENSE_RESISTOR 91
+ #define X2_MICROSTEPS 16
+
+ #define Y_MAX_CURRENT 1000
+ #define Y_SENSE_RESISTOR 91
+ #define Y_MICROSTEPS 16
+
+ #define Y2_MAX_CURRENT 1000
+ #define Y2_SENSE_RESISTOR 91
+ #define Y2_MICROSTEPS 16
+
+ #define Z_MAX_CURRENT 1000
+ #define Z_SENSE_RESISTOR 91
+ #define Z_MICROSTEPS 16
+
+ #define Z2_MAX_CURRENT 1000
+ #define Z2_SENSE_RESISTOR 91
+ #define Z2_MICROSTEPS 16
+
+ #define E0_MAX_CURRENT 1000
+ #define E0_SENSE_RESISTOR 91
+ #define E0_MICROSTEPS 16
+
+ #define E1_MAX_CURRENT 1000
+ #define E1_SENSE_RESISTOR 91
+ #define E1_MICROSTEPS 16
+
+ #define E2_MAX_CURRENT 1000
+ #define E2_SENSE_RESISTOR 91
+ #define E2_MICROSTEPS 16
+
+ #define E3_MAX_CURRENT 1000
+ #define E3_SENSE_RESISTOR 91
+ #define E3_MICROSTEPS 16
+
+ #define E4_MAX_CURRENT 1000
+ #define E4_SENSE_RESISTOR 91
+ #define E4_MICROSTEPS 16
+
+#endif
+
+// @section TMC2130
+
+/**
+ * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
+ *
+ * You'll also need the TMC2130Stepper Arduino library
+ * (https://github.com/teemuatlut/TMC2130Stepper).
+ *
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
+ * the hardware SPI interface on your board and define the required CS pins
+ * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ */
+//#define HAVE_TMC2130
+
+#if ENABLED(HAVE_TMC2130)
+
+ // CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
+ //#define X_IS_TMC2130
+ //#define X2_IS_TMC2130
+ //#define Y_IS_TMC2130
+ //#define Y2_IS_TMC2130
+ //#define Z_IS_TMC2130
+ //#define Z2_IS_TMC2130
+ //#define E0_IS_TMC2130
+ //#define E1_IS_TMC2130
+ //#define E2_IS_TMC2130
+ //#define E3_IS_TMC2130
+ //#define E4_IS_TMC2130
+
+ /**
+ * Stepper driver settings
+ */
+
+ #define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
+ #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
+ #define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
+
+ #define X_CURRENT 1000 // rms current in mA. Multiply by 1.41 for peak current.
+ #define X_MICROSTEPS 16 // 0..256
+
+ #define Y_CURRENT 1000
+ #define Y_MICROSTEPS 16
+
+ #define Z_CURRENT 1000
+ #define Z_MICROSTEPS 16
+
+ //#define X2_CURRENT 1000
+ //#define X2_MICROSTEPS 16
+
+ //#define Y2_CURRENT 1000
+ //#define Y2_MICROSTEPS 16
+
+ //#define Z2_CURRENT 1000
+ //#define Z2_MICROSTEPS 16
+
+ //#define E0_CURRENT 1000
+ //#define E0_MICROSTEPS 16
+
+ //#define E1_CURRENT 1000
+ //#define E1_MICROSTEPS 16
+
+ //#define E2_CURRENT 1000
+ //#define E2_MICROSTEPS 16
+
+ //#define E3_CURRENT 1000
+ //#define E3_MICROSTEPS 16
+
+ //#define E4_CURRENT 1000
+ //#define E4_MICROSTEPS 16
+
+ /**
+ * Use Trinamic's ultra quiet stepping mode.
+ * When disabled, Marlin will use spreadCycle stepping mode.
+ */
+ #define STEALTHCHOP
+
+ /**
+ * Let Marlin automatically control stepper current.
+ * This is still an experimental feature.
+ * Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
+ * then decrease current by CURRENT_STEP until temperature prewarn is cleared.
+ * Adjusting starts from X/Y/Z/E_CURRENT but will not increase over AUTO_ADJUST_MAX
+ * Relevant g-codes:
+ * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given.
+ * M906 S1 - Start adjusting current
+ * M906 S0 - Stop adjusting current
+ * M911 - Report stepper driver overtemperature pre-warn condition.
+ * M912 - Clear stepper driver overtemperature pre-warn condition flag.
+ */
+ //#define AUTOMATIC_CURRENT_CONTROL
+
+ #if ENABLED(AUTOMATIC_CURRENT_CONTROL)
+ #define CURRENT_STEP 50 // [mA]
+ #define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
+ #define REPORT_CURRENT_CHANGE
+ #endif
+
+ /**
+ * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD.
+ * This mode allows for faster movements at the expense of higher noise levels.
+ * STEALTHCHOP needs to be enabled.
+ * M913 X/Y/Z/E to live tune the setting
+ */
+ //#define HYBRID_THRESHOLD
+
+ #define X_HYBRID_THRESHOLD 100 // [mm/s]
+ #define X2_HYBRID_THRESHOLD 100
+ #define Y_HYBRID_THRESHOLD 100
+ #define Y2_HYBRID_THRESHOLD 100
+ #define Z_HYBRID_THRESHOLD 4
+ #define Z2_HYBRID_THRESHOLD 4
+ #define E0_HYBRID_THRESHOLD 30
+ #define E1_HYBRID_THRESHOLD 30
+ #define E2_HYBRID_THRESHOLD 30
+ #define E3_HYBRID_THRESHOLD 30
+ #define E4_HYBRID_THRESHOLD 30
+
+ /**
+ * Use stallGuard2 to sense an obstacle and trigger an endstop.
+ * You need to place a wire from the driver's DIAG1 pin to the X/Y endstop pin.
+ * If used along with STEALTHCHOP, the movement will be louder when homing. This is normal.
+ *
+ * X/Y_HOMING_SENSITIVITY is used for tuning the trigger sensitivity.
+ * Higher values make the system LESS sensitive.
+ * Lower value make the system MORE sensitive.
+ * Too low values can lead to false positives, while too high values will collide the axis without triggering.
+ * It is advised to set X/Y_HOME_BUMP_MM to 0.
+ * M914 X/Y to live tune the setting
+ */
+ //#define SENSORLESS_HOMING
+
+ #if ENABLED(SENSORLESS_HOMING)
+ #define X_HOMING_SENSITIVITY 19
+ #define Y_HOMING_SENSITIVITY 19
+ #endif
+
+ /**
+ * You can set your own advanced settings by filling in predefined functions.
+ * A list of available functions can be found on the library github page
+ * https://github.com/teemuatlut/TMC2130Stepper
+ *
+ * Example:
+ * #define TMC2130_ADV() { \
+ * stepperX.diag0_temp_prewarn(1); \
+ * stepperX.interpolate(0); \
+ * }
+ */
+ #define TMC2130_ADV() { }
+
+#endif // HAVE_TMC2130
+
+// @section L6470
+
+/**
+ * Enable this section if you have L6470 motor drivers.
+ * You need to import the L6470 library into the Arduino IDE for this.
+ * (https://github.com/ameyer/Arduino-L6470)
+ */
+
+//#define HAVE_L6470DRIVER
+#if ENABLED(HAVE_L6470DRIVER)
+
+ //#define X_IS_L6470
+ //#define X2_IS_L6470
+ //#define Y_IS_L6470
+ //#define Y2_IS_L6470
+ //#define Z_IS_L6470
+ //#define Z2_IS_L6470
+ //#define E0_IS_L6470
+ //#define E1_IS_L6470
+ //#define E2_IS_L6470
+ //#define E3_IS_L6470
+ //#define E4_IS_L6470
+
+ #define X_MICROSTEPS 16 // number of microsteps
+ #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
+ #define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
+ #define X_STALLCURRENT 1500 // current in mA where the driver will detect a stall
+
+ #define X2_MICROSTEPS 16
+ #define X2_K_VAL 50
+ #define X2_OVERCURRENT 2000
+ #define X2_STALLCURRENT 1500
+
+ #define Y_MICROSTEPS 16
+ #define Y_K_VAL 50
+ #define Y_OVERCURRENT 2000
+ #define Y_STALLCURRENT 1500
+
+ #define Y2_MICROSTEPS 16
+ #define Y2_K_VAL 50
+ #define Y2_OVERCURRENT 2000
+ #define Y2_STALLCURRENT 1500
+
+ #define Z_MICROSTEPS 16
+ #define Z_K_VAL 50
+ #define Z_OVERCURRENT 2000
+ #define Z_STALLCURRENT 1500
+
+ #define Z2_MICROSTEPS 16
+ #define Z2_K_VAL 50
+ #define Z2_OVERCURRENT 2000
+ #define Z2_STALLCURRENT 1500
+
+ #define E0_MICROSTEPS 16
+ #define E0_K_VAL 50
+ #define E0_OVERCURRENT 2000
+ #define E0_STALLCURRENT 1500
+
+ #define E1_MICROSTEPS 16
+ #define E1_K_VAL 50
+ #define E1_OVERCURRENT 2000
+ #define E1_STALLCURRENT 1500
+
+ #define E2_MICROSTEPS 16
+ #define E2_K_VAL 50
+ #define E2_OVERCURRENT 2000
+ #define E2_STALLCURRENT 1500
+
+ #define E3_MICROSTEPS 16
+ #define E3_K_VAL 50
+ #define E3_OVERCURRENT 2000
+ #define E3_STALLCURRENT 1500
+
+ #define E4_MICROSTEPS 16
+ #define E4_K_VAL 50
+ #define E4_OVERCURRENT 2000
+ #define E4_STALLCURRENT 1500
+
+#endif
+
+/**
+ * TWI/I2C BUS
+ *
+ * This feature is an EXPERIMENTAL feature so it shall not be used on production
+ * machines. Enabling this will allow you to send and receive I2C data from slave
+ * devices on the bus.
+ *
+ * ; Example #1
+ * ; This macro send the string "Marlin" to the slave device with address 0x63 (99)
+ * ; It uses multiple M260 commands with one B arg
+ * M260 A99 ; Target slave address
+ * M260 B77 ; M
+ * M260 B97 ; a
+ * M260 B114 ; r
+ * M260 B108 ; l
+ * M260 B105 ; i
+ * M260 B110 ; n
+ * M260 S1 ; Send the current buffer
+ *
+ * ; Example #2
+ * ; Request 6 bytes from slave device with address 0x63 (99)
+ * M261 A99 B5
+ *
+ * ; Example #3
+ * ; Example serial output of a M261 request
+ * echo:i2c-reply: from:99 bytes:5 data:hello
+ */
+
+// @section i2cbus
+
+//#define EXPERIMENTAL_I2CBUS
+#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
+
+// @section extras
+
+/**
+ * Spindle & Laser control
+ *
+ * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
+ * to set spindle speed, spindle direction, and laser power.
+ *
+ * SuperPid is a router/spindle speed controller used in the CNC milling community.
+ * Marlin can be used to turn the spindle on and off. It can also be used to set
+ * the spindle speed from 5,000 to 30,000 RPM.
+ *
+ * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
+ * hardware PWM pin for the speed control and a pin for the rotation direction.
+ *
+ * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
+ */
+//#define SPINDLE_LASER_ENABLE
+#if ENABLED(SPINDLE_LASER_ENABLE)
+
+ #define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
+ #define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
+ #define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
+ #define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
+ #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
+ #define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
+ #define SPINDLE_INVERT_DIR false
+ #define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
+
+ /**
+ * The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
+ *
+ * SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
+ * where PWM duty cycle varies from 0 to 255
+ *
+ * set the following for your controller (ALL MUST BE SET)
+ */
+
+ #define SPEED_POWER_SLOPE 118.4
+ #define SPEED_POWER_INTERCEPT 0
+ #define SPEED_POWER_MIN 5000
+ #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
+
+ //#define SPEED_POWER_SLOPE 0.3922
+ //#define SPEED_POWER_INTERCEPT 0
+ //#define SPEED_POWER_MIN 10
+ //#define SPEED_POWER_MAX 100 // 0-100%
+#endif
+
+/**
+ * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
+ */
+//#define PINS_DEBUGGING
+
+/**
+ * Auto-report temperatures with M155 S
+ */
+//#define AUTO_REPORT_TEMPERATURES
+
+/**
+ * Include capabilities in M115 output
+ */
+//#define EXTENDED_CAPABILITIES_REPORT
+
+/**
+ * Volumetric extrusion default state
+ * Activate to make volumetric extrusion the default method,
+ * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter.
+ *
+ * M200 D0 to disable, M200 Dn to set a new diameter.
+ */
+//#define VOLUMETRIC_DEFAULT_ON
+
+/**
+ * Enable this option for a leaner build of Marlin that removes all
+ * workspace offsets, simplifying coordinate transformations, leveling, etc.
+ *
+ * - M206 and M428 are disabled.
+ * - G92 will revert to its behavior from Marlin 1.0.
+ */
+//#define NO_WORKSPACE_OFFSETS
+
+/**
+ * Set the number of proportional font spaces required to fill up a typical character space.
+ * This can help to better align the output of commands like `G29 O` Mesh Output.
+ *
+ * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0.
+ * Otherwise, adjust according to your client and font.
+ */
+#define PROPORTIONAL_FONT_RATIO 1.0
+
+/**
+ * Spend 28 bytes of SRAM to optimize the GCode parser
+ */
+#define FASTER_GCODE_PARSER
+
+/**
+ * User-defined menu items that execute custom GCode
+ */
+//#define CUSTOM_USER_MENUS
+#if ENABLED(CUSTOM_USER_MENUS)
+ #define USER_SCRIPT_DONE "M117 User Script Done"
+
+ #define USER_DESC_1 "Home & UBL Info"
+ #define USER_GCODE_1 "G28\nG29 W"
+
+ #define USER_DESC_2 "Preheat for PLA"
+ #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
+
+ #define USER_DESC_3 "Preheat for ABS"
+ #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
+
+ #define USER_DESC_4 "Heat Bed/Home/Level"
+ #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
+
+ #define USER_DESC_5 "Home & Info"
+ #define USER_GCODE_5 "G28\nM503"
+#endif
+
+//===========================================================================
+//============================ I2C Encoder Settings =========================
+//===========================================================================
+/**
+ * I2C position encoders for closed loop control.
+ * Developed by Chris Barr at Aus3D.
+ *
+ * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder
+ * Github: https://github.com/Aus3D/MagneticEncoder
+ *
+ * Supplier: http://aus3d.com.au/magnetic-encoder-module
+ * Alternative Supplier: http://reliabuild3d.com/
+ *
+ * Reilabuild encoders have been modified to improve reliability.
+ */
+
+//#define I2C_POSITION_ENCODERS
+#if ENABLED(I2C_POSITION_ENCODERS)
+
+ #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5
+ // encoders supported currently.
+
+ #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200.
+ #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. _AXIS.
+ #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or-
+ // I2CPE_ENC_TYPE_ROTARY.
+ #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for
+ // 1mm poles. For linear encoders this is ticks / mm,
+ // for rotary encoders this is ticks / revolution.
+ //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper
+ // steps per full revolution (motor steps/rev * microstepping)
+ //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel.
+ #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_NONE // Type of error error correction.
+ #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the
+ // printer will attempt to correct the error; errors
+ // smaller than this are ignored to minimize effects of
+ // measurement noise / latency (filter).
+
+ #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2.
+ #define I2CPE_ENC_2_AXIS Y_AXIS
+ #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR
+ #define I2CPE_ENC_2_TICKS_UNIT 2048
+ //#define I2CPE_ENC_2_TICKS_REV (16 * 200)
+ //#define I2CPE_ENC_2_INVERT
+ #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_NONE
+ #define I2CPE_ENC_2_EC_THRESH 0.10
+
+ #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options
+ #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below.
+
+ #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4.
+ #define I2CPE_ENC_4_AXIS E_AXIS
+
+ #define I2CPE_ENC_5_ADDR 34 // Encoder 5.
+ #define I2CPE_ENC_5_AXIS E_AXIS
+
+ // Default settings for encoders which are enabled, but without settings configured above.
+ #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR
+ #define I2CPE_DEF_ENC_TICKS_UNIT 2048
+ #define I2CPE_DEF_TICKS_REV (16 * 200)
+ #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE
+ #define I2CPE_DEF_EC_THRESH 0.1
+
+ //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
+ // axis after which the printer will abort. Comment out to
+ // disable abort behaviour.
+
+ #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
+ // for this amount of time (in ms) before the encoder
+ // is trusted again.
+
+ /**
+ * Position is checked every time a new command is executed from the buffer but during long moves,
+ * this setting determines the minimum update time between checks. A value of 100 works well with
+ * error rolling average when attempting to correct only for skips and not for vibration.
+ */
+ #define I2CPE_MIN_UPD_TIME_MS 100 // Minimum time in miliseconds between encoder checks.
+
+ // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
+ #define I2CPE_ERR_ROLLING_AVERAGE
+
+#endif
+
+#endif // CONFIGURATION_ADV_H
diff --git a/Marlin/example_configurations/CL-260/Configuration.h b/Marlin/example_configurations/CL-260/Configuration.h
index 6dc34f701..90da7b05f 100644
--- a/Marlin/example_configurations/CL-260/Configuration.h
+++ b/Marlin/example_configurations/CL-260/Configuration.h
@@ -1370,6 +1370,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/Cartesio/Configuration.h b/Marlin/example_configurations/Cartesio/Configuration.h
index fb59f90cb..0d84d53bf 100644
--- a/Marlin/example_configurations/Cartesio/Configuration.h
+++ b/Marlin/example_configurations/Cartesio/Configuration.h
@@ -1367,6 +1367,16 @@
//
#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h
index 19482bdd9..d3e288c05 100644
--- a/Marlin/example_configurations/Felix/Configuration.h
+++ b/Marlin/example_configurations/Felix/Configuration.h
@@ -1351,6 +1351,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/Felix/DUAL/Configuration.h b/Marlin/example_configurations/Felix/DUAL/Configuration.h
index e18486263..ad8553a94 100644
--- a/Marlin/example_configurations/Felix/DUAL/Configuration.h
+++ b/Marlin/example_configurations/Felix/DUAL/Configuration.h
@@ -1351,6 +1351,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/FolgerTech-i3-2020/Configuration.h b/Marlin/example_configurations/FolgerTech-i3-2020/Configuration.h
index ec90ea162..13892b277 100644
--- a/Marlin/example_configurations/FolgerTech-i3-2020/Configuration.h
+++ b/Marlin/example_configurations/FolgerTech-i3-2020/Configuration.h
@@ -1373,6 +1373,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h
index a5a749ae8..153e6028d 100644
--- a/Marlin/example_configurations/Hephestos/Configuration.h
+++ b/Marlin/example_configurations/Hephestos/Configuration.h
@@ -1359,6 +1359,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/Hephestos_2/Configuration.h b/Marlin/example_configurations/Hephestos_2/Configuration.h
index e04bca553..2864c04b0 100644
--- a/Marlin/example_configurations/Hephestos_2/Configuration.h
+++ b/Marlin/example_configurations/Hephestos_2/Configuration.h
@@ -1362,6 +1362,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h
index 3e53a914a..05a6c11a8 100644
--- a/Marlin/example_configurations/K8200/Configuration.h
+++ b/Marlin/example_configurations/K8200/Configuration.h
@@ -1401,6 +1401,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/K8400/Configuration.h b/Marlin/example_configurations/K8400/Configuration.h
index b3a0efdda..ec265fcc9 100644
--- a/Marlin/example_configurations/K8400/Configuration.h
+++ b/Marlin/example_configurations/K8400/Configuration.h
@@ -1369,6 +1369,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/K8400/Dual-head/Configuration.h b/Marlin/example_configurations/K8400/Dual-head/Configuration.h
index 6a7578a8f..9b60e1740 100644
--- a/Marlin/example_configurations/K8400/Dual-head/Configuration.h
+++ b/Marlin/example_configurations/K8400/Dual-head/Configuration.h
@@ -1369,6 +1369,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/M150/Configuration.h b/Marlin/example_configurations/M150/Configuration.h
index d46c89bc7..d47a8526a 100644
--- a/Marlin/example_configurations/M150/Configuration.h
+++ b/Marlin/example_configurations/M150/Configuration.h
@@ -1396,6 +1396,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
index 1e324da60..b008062b3 100644
--- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
+++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
@@ -1369,6 +1369,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h
index bd12ed76f..b05d00937 100644
--- a/Marlin/example_configurations/RigidBot/Configuration.h
+++ b/Marlin/example_configurations/RigidBot/Configuration.h
@@ -1369,6 +1369,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h
index 4b95472db..06c2a3230 100644
--- a/Marlin/example_configurations/SCARA/Configuration.h
+++ b/Marlin/example_configurations/SCARA/Configuration.h
@@ -1381,6 +1381,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/TAZ4/Configuration.h b/Marlin/example_configurations/TAZ4/Configuration.h
index 48c565fe4..86d9c1bd8 100644
--- a/Marlin/example_configurations/TAZ4/Configuration.h
+++ b/Marlin/example_configurations/TAZ4/Configuration.h
@@ -1388,6 +1388,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/TinyBoy2/Configuration.h b/Marlin/example_configurations/TinyBoy2/Configuration.h
index c3b98ce23..4ecc19dc7 100644
--- a/Marlin/example_configurations/TinyBoy2/Configuration.h
+++ b/Marlin/example_configurations/TinyBoy2/Configuration.h
@@ -1425,6 +1425,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h
index 94e68004f..cd4df35ec 100644
--- a/Marlin/example_configurations/WITBOX/Configuration.h
+++ b/Marlin/example_configurations/WITBOX/Configuration.h
@@ -1359,6 +1359,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
index aed973a9a..dd458267d 100644
--- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h
+++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
@@ -1369,6 +1369,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h
index 053f92fa5..66bd78c4c 100644
--- a/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h
+++ b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h
@@ -1490,6 +1490,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h
index 7a3a870af..f3d95861b 100644
--- a/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h
+++ b/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h
@@ -1491,6 +1491,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h
index befd585f9..009e87919 100644
--- a/Marlin/example_configurations/delta/generic/Configuration.h
+++ b/Marlin/example_configurations/delta/generic/Configuration.h
@@ -1480,6 +1480,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
index 694de7ca2..840f03f9d 100644
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
@@ -1483,6 +1483,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
index 24476bbd0..84ba27323 100644
--- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
@@ -1488,6 +1488,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration.h b/Marlin/example_configurations/delta/kossel_xl/Configuration.h
index 84bfd7f03..76ffbbcd6 100644
--- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h
@@ -1546,6 +1546,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/gCreate_gMax1.5+/Configuration.h b/Marlin/example_configurations/gCreate_gMax1.5+/Configuration.h
index f55d5d337..97348c179 100644
--- a/Marlin/example_configurations/gCreate_gMax1.5+/Configuration.h
+++ b/Marlin/example_configurations/gCreate_gMax1.5+/Configuration.h
@@ -1385,6 +1385,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h
index 968eebe0d..dfe778b3b 100644
--- a/Marlin/example_configurations/makibox/Configuration.h
+++ b/Marlin/example_configurations/makibox/Configuration.h
@@ -1372,6 +1372,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
index 0e366f01f..ab56d7eb0 100644
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
@@ -1364,6 +1364,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/example_configurations/wt150/Configuration.h b/Marlin/example_configurations/wt150/Configuration.h
index c0d602f83..a023c3f16 100644
--- a/Marlin/example_configurations/wt150/Configuration.h
+++ b/Marlin/example_configurations/wt150/Configuration.h
@@ -1375,6 +1375,16 @@
//
//#define CARTESIO_UI
+//
+// ANET_10 Controller supported displays.
+//
+//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+ // This LCD is known to be susceptible to electrical interference
+ // which scrambles the display. Pressing any button clears it up.
+//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+ // A clone of the RepRapDiscount full graphics display but with
+ // different pins/wiring (see pins_ANET_10.h).
+
//
// CONTROLLER TYPE: I2C
//
diff --git a/Marlin/pins.h b/Marlin/pins.h
index 0b43a7a1c..2a0b92aa9 100644
--- a/Marlin/pins.h
+++ b/Marlin/pins.h
@@ -107,6 +107,8 @@
#include "pins_AZTEEG_X3.h"
#elif MB(AZTEEG_X3_PRO)
#include "pins_AZTEEG_X3_PRO.h"
+#elif MB(ANET_10)
+ #include "pins_ANET_10.h"
#elif MB(ULTIMAKER)
#include "pins_ULTIMAKER.h"
#elif MB(ULTIMAKER_OLD)
diff --git a/Marlin/pinsDebug.h b/Marlin/pinsDebug.h
index 495513a89..3e978ecb8 100644
--- a/Marlin/pinsDebug.h
+++ b/Marlin/pinsDebug.h
@@ -129,6 +129,11 @@ const PinInfo pin_array[] PROGMEM = {
bool get_pinMode(int8_t pin) {return *portModeRegister(digitalPinToPort_DEBUG(pin)) & digitalPinToBitMask_DEBUG(pin); }
#endif
+#if defined(__AVR_ATmega1284P__) // 1284 IDE extensions set this to the number of
+ #undef NUM_DIGITAL_PINS // digital only pins while all other CPUs have it
+ #define NUM_DIGITAL_PINS 32 // set to digital only + digital/analog
+#endif
+
#define PWM_PRINT(V) do{ sprintf_P(buffer, PSTR("PWM: %4d"), V); SERIAL_ECHO(buffer); }while(0)
#define PWM_CASE(N,Z) \
case TIMER##N##Z: \
diff --git a/Marlin/pinsDebug_list.h b/Marlin/pinsDebug_list.h
index 9164b6b41..b4cc4c29f 100644
--- a/Marlin/pinsDebug_list.h
+++ b/Marlin/pinsDebug_list.h
@@ -29,6 +29,9 @@
#line 0 // set __LINE__ to a known value for both passes
+#if PIN_EXISTS(ADC_KEYPAD) && ADC_KEYPAD_PIN < NUM_ANALOG_INPUTS
+ REPORT_NAME_ANALOG(ADC_KEYPAD_PIN, __LINE__ )
+#endif
#if defined(__FD) && __FD >= 0
REPORT_NAME_DIGITAL(__FD, __LINE__ )
#endif
diff --git a/Marlin/pins_ANET_10.h b/Marlin/pins_ANET_10.h
new file mode 100644
index 000000000..cf97170bc
--- /dev/null
+++ b/Marlin/pins_ANET_10.h
@@ -0,0 +1,274 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see .
+ *
+ */
+
+/**
+ * Anet V1.0 board pin assignments
+ */
+
+/**
+ * Rev B 16 JUN 2017
+ *
+ * 1) no longer uses Sanguino files to define some of the pins
+ * 2) added pointers to useable Arduino IDE extensions
+ *
+ */
+
+/**
+ * The standard Arduino IDE extension (board manager) for this board
+ * is located at https://github.com/SkyNet3D/anet-board.
+ *
+ * Installation instructions are on that page.
+ *
+ * After copying the files to the appropriate location, restart Arduino and
+ * you'll see "Anet V1.0" and "Anet V1.0 (Optiboot)" in the boards list.
+ *
+ * "Anet V1.0" uses the bootloader that was installed on the board when
+ * it shipped from the factory.
+ *
+ * "Anet V1.0 (Optiboot)" frees up another 3K of FLASH. You'll need to burn
+ * a new bootloader to the board to be able to automatically download a
+ * compiled image.
+ *
+ */
+
+/**
+ * Another usable Arduino IDE extension (board manager) can be found at
+ * https://github.com/Lauszus/Sanguino
+ *
+ * This extension has been tested on Arduino 1.6.12 & 1.8.0
+ *
+ * Here's the JSON path:
+ * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
+ *
+ * When installing select 1.0.2
+ *
+ * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
+ * Just use the above JSON URL instead of Sparkfun's JSON.
+ *
+ * Once installed select the Sanguino board and then select the CPU.
+ *
+ */
+
+/**
+ * To burn a new bootloader:
+ *
+ * 1. Connect your programmer to the board.
+ * 2. In the Arduino IDE select the board and then select the programmer.
+ * 3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message.
+ * 4. The programmer is no longer needed. Remove it.
+ */
+
+/**
+ * Additional info:
+ *
+ * Anet Schematics - https://github.com/ralf-e/ANET-3D-Board-V1.0
+ * Wiring RRDFG Smart Controller - http://www.thingiverse.com/thing:2103748
+ * SkyNet3D Anet software development - https://github.com/SkyNet3D/Marlin/
+ * Anet Users / Skynet SW on Facebook - https://www.facebook.com/skynet3ddevelopment/
+ *
+ * Many thanks to Hans Raaf (@oderwat) for developing the Anet-specific software and supporting the Anet community.
+*/
+
+#if !defined(__AVR_ATmega1284P__)
+ #error "Oops! Make sure you have 'Anet V1.0', 'Anet V1.0 (Optiboot)' or 'Sanguino' selected from the 'Tools -> Boards' menu."
+#endif
+
+#ifndef BOARD_NAME
+ #define BOARD_NAME "Anet"
+#endif
+
+#define LARGE_FLASH true
+
+//
+// Limit Switches
+//
+#define X_STOP_PIN 18
+#define Y_STOP_PIN 19
+#define Z_STOP_PIN 20
+
+//
+// Steppers
+//
+#define X_STEP_PIN 15
+#define X_DIR_PIN 21
+#define X_ENABLE_PIN 14
+
+#define Y_STEP_PIN 22
+#define Y_DIR_PIN 23
+#define Y_ENABLE_PIN 14
+
+#define Z_STEP_PIN 3
+#define Z_DIR_PIN 2
+#define Z_ENABLE_PIN 26
+
+#define E0_STEP_PIN 1
+#define E0_DIR_PIN 0
+#define E0_ENABLE_PIN 14
+
+//
+// Temperature Sensors
+//
+#define TEMP_0_PIN 7 // Analog Input (pin 33 extruder)
+#define TEMP_BED_PIN 6 // Analog Input (pin 34 bed)
+
+//
+// Heaters / Fans
+//
+#define HEATER_0_PIN 13 // (extruder)
+#define HEATER_BED_PIN 12 // (bed)
+#define FAN_PIN 4
+
+//
+// Misc. Functions
+//
+#define SDSS 31
+#define LED_PIN -1
+
+/**
+ * LCD / Controller
+ *
+ * Only the following displays are supported:
+ * ANET_KEYPAD_LCD
+ * ANET_FULL_GRAPHICS_LCD
+ * REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+*/
+
+#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
+ #define LCD_SDSS 28
+ #if ENABLED(ADC_KEYPAD)
+ #define SERVO0_PIN 27 // free for BLTouch/3D-Touch
+ #define LCD_PINS_RS 28
+ #define LCD_PINS_ENABLE 29
+ #define LCD_PINS_D4 10
+ #define LCD_PINS_D5 11
+ #define LCD_PINS_D6 16
+ #define LCD_PINS_D7 17
+ #define BTN_EN1 -1
+ #define BTN_EN2 -1
+ #define BTN_ENC -1
+ #define ADC_KEYPAD_PIN 1
+ #define ENCODER_FEEDRATE_DEADZONE 2
+ #elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) || ENABLED(ANET_FULL_GRAPHICS_LCD)
+ // Pin definitions for the Anet A6 Full Graphics display and the RepRapDiscount Full Graphics
+ // display using an adapter board // https://go.aisler.net/benlye/anet-lcd-adapter/pcb
+ // See below for alternative pin definitions for use with https://www.thingiverse.com/thing:2103748
+ #define SERVO0_PIN 29 // free for BLTouch/3D-Touch
+ #define BEEPER_PIN 17
+ #define LCD_PINS_RS 27
+ #define LCD_PINS_ENABLE 28
+ #define LCD_PINS_D4 30
+ #define BTN_EN1 11
+ #define BTN_EN2 10
+ #define BTN_ENC 16
+ #define ST7920_DELAY_1 DELAY_0_NOP
+ #define ST7920_DELAY_2 DELAY_1_NOP
+ #define ST7920_DELAY_3 DELAY_2_NOP
+ #ifndef ENCODER_STEPS_PER_MENU_ITEM
+ #define ENCODER_STEPS_PER_MENU_ITEM 1
+ #endif
+ #ifndef ENCODER_PULSES_PER_STEP
+ #define ENCODER_PULSES_PER_STEP 4
+ #endif
+ #endif
+#endif // ULTRA_LCD && NEWPANEL
+
+/**
+ * ====================================================================
+ * =============== Alternative RepRapDiscount Wiring ==================
+ * ====================================================================
+ *
+ * An alternative wiring scheme for the RepRapDiscount Full Graphics Display is
+ * published by oderwat on Thingiverse at https://www.thingiverse.com/thing:2103748.
+ *
+ * Using that adapter requires changing the pin definition as follows:
+ * #define SERVO0_PIN 27 // free for BLTouch/3D-Touch
+ * #define BEEPER_PIN 28
+ * #define LCD_PINS_RS 30
+ * #define LCD_PINS_ENABLE 29
+ * #define LCD_PINS_D4 17
+ *
+ * The BLTouch pin becomes LCD:3
+ */
+
+/**
+ * ====================================================================
+ * ===================== LCD PINOUTS ==================================
+ * ====================================================================
+ *
+ * Anet V1.0 controller | ANET_KEYPAD_LCD | ANET_FULL_ | RepRapDiscount Full | Thingiverse RepRap wiring
+ * physical logical alt | | GRAPHICS_LCD | Graphics Display Wiring | http://www.thingiverse
+ * pin pin functions | | | | .com/thing:2103748
+ *------------------------------------------------------------------------------------------------------------------------
+ * ANET-J3.1 8 *** | N/A | J3_TX *** | |
+ * ANET-J3.2 9 *** | N/A | J3_RX *** | |
+ * ANET-J3.3 6 MISO | N/A | MISO *** | EXP2.1 MISO | EXP2.1 MISO
+ * ANET-J3.4 +5V | N/A | +5V | |
+ * ANET-J3.5 7 SCK | N/A | SCK *** | EXP2.2 SCK | EXP2.2 SCK
+ * ANET-J3.6 5 MOSI | N/A | MOSI *** | EXP2.6 MOSI | EXP2.6 MOSI
+ * ANET-J3.7 !RESET | N/A | button | EXP2.8 panel button | EXP2.8 panel button
+ * ANET-J3.8 GND | N/A | GND | EXP2.9 GND | EXP2.9 GND
+ * ANET-J3.9 4 Don't use | N/A | N/C | |
+ * ANET-J3.10 +3.3V | N/A | +3.3V *** | |
+ * | | | |
+ * | | | |
+ * ANET-LCD.1 GND | GND | GND | EXP1.9 GND | EXP1.9 GND
+ * ANET-LCD.2 +5V | +5V | +5V | EXP1.10 +5V | EXP1.10 +5V
+ * ANET-LCD.3 27 A4 | N/C * | LCD_PINS_RS | EXP1.4 LCD_PINS_RS | EXP2.4 SDSS or N/C *
+ * ANET-LCD.4 10 | LCD_PINS_D4 | BTN_EN2 | EXP2.3 BTN_EN2 | EXP2.3 BTN_EN2
+ * ANET-LCD.5 28 A3 | LCD_PINS_RS | LCD_PINS_ENABLE | EXP1.3 LCD_PINS_ENABLE | EXP1.1 BEEPER_PIN
+ * ANET-LCD.6 11 | LCD_PINS_D5 | BTN_EN1 | EXP2.5 BTN_EN1 | EXP2.5 BTN_EN1
+ * ANET-LCD.7 29 A2 | LCD_PINS_ENABLE | N/C * | EXP2.4 SDSS or N/C * | EXP1.3 LCD_PINS_ENABLE
+ * ANET-LCD.8 16 SCL | LCD_PINS_D6 | BTN_ENC | EXP1.2 BTN_ENC | EXP1.2 BTN_ENC
+ * ANET-LCD.9 30 A1 | ADC_KEYPAD_PIN ** | LCD_PINS_D4 | EXP1.5 LCD_PINS_D4 | EXP1.4 LCD_PINS_RS
+ * ANET-LCD.10 17 SDA | LCD_PINS_D7 | BEEPER_PIN | EXP1.1 BEEPER_PIN | EXP1.5 LCD_PINS_D4
+ *
+ * N/C * - if not connected to the LCD can be used for BLTouch servo input
+ * ** - analog pin -WITHOUT a pullup
+ * *** - only connected to something if the Bluetooth module is populated
+ */
+
+/**
+ * REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+ * physical pin function
+ * EXP1.1 BEEPER
+ * EXP1.2 BTN_ENC
+ * EXP1.3 LCD_PINS_ENABLE
+ * EXP1.4 LCD_PINS_RS
+ * EXP1.5 LCD_PINS_D4
+ * EXP1.6 LCD_PINS_D5 (not used)
+ * EXP1.7 LCD_PINS_D6 (not used)
+ * EXP1.8 LCD_PINS_D7 (not used)
+ * EXP1.9 GND
+ * EXP1.10 VCC
+ *
+ *
+ * EXP2.1 MISO
+ * EXP2.2 SCK
+ * EXP2.3 BTN_EN2
+ * EXP2.4 SDSS
+ * EXP2.5 BTN_EN1
+ * EXP2.6 MOSI
+ * EXP2.7 SD_DETECT_PIN
+ * EXP2.8 button
+ * EXP2.9 GND
+ * EXP2.10 NC
+ */
diff --git a/Marlin/temperature.cpp b/Marlin/temperature.cpp
index 6111bab44..a4fdcf985 100644
--- a/Marlin/temperature.cpp
+++ b/Marlin/temperature.cpp
@@ -212,6 +212,11 @@ uint8_t Temperature::soft_pwm_amount[HOTENDS],
#endif
#endif
+#if ENABLED(ADC_KEYPAD)
+ uint32_t Temperature::current_ADCKey_raw = 0;
+ uint8_t Temperature::ADCKey_count = 0;
+#endif
+
#if HAS_PID_HEATING
void Temperature::PID_autotune(float temp, int hotend, int ncycles, bool set_result/*=false*/) {
@@ -1625,6 +1630,9 @@ void Temperature::isr() {
static uint8_t pwm_count = _BV(SOFT_PWM_SCALE);
// avoid multiple loads of pwm_count
uint8_t pwm_count_tmp = pwm_count;
+ #if ENABLED(ADC_KEYPAD)
+ static unsigned int raw_ADCKey_value = 0;
+ #endif
// Static members for each heater
#if ENABLED(SLOW_PWM_HEATERS)
@@ -1997,9 +2005,29 @@ void Temperature::isr() {
raw_filwidth_value -= (raw_filwidth_value >> 7); // Subtract 1/128th of the raw_filwidth_value
raw_filwidth_value += ((unsigned long)ADC << 7); // Add new ADC reading, scaled by 128
}
- break;
+ break;
#endif
+ #if ENABLED(ADC_KEYPAD)
+ case Prepare_ADC_KEY:
+ START_ADC(ADC_KEYPAD_PIN);
+ break;
+ case Measure_ADC_KEY:
+ if (ADCKey_count < 16) {
+ raw_ADCKey_value = ADC;
+ if (raw_ADCKey_value > 900) {
+ //ADC Key release
+ ADCKey_count = 0;
+ current_ADCKey_raw = 0;
+ }
+ else {
+ current_ADCKey_raw += raw_ADCKey_value;
+ ADCKey_count++;
+ }
+ }
+ break;
+ #endif // ADC_KEYPAD
+
case StartupDelay: break;
} // switch(adc_sensor_state)
diff --git a/Marlin/temperature.h b/Marlin/temperature.h
index 60a85684a..6ce644d88 100644
--- a/Marlin/temperature.h
+++ b/Marlin/temperature.h
@@ -81,6 +81,10 @@ enum ADCSensorState {
Prepare_FILWIDTH,
Measure_FILWIDTH,
#endif
+ #if ENABLED(ADC_KEYPAD)
+ Prepare_ADC_KEY,
+ Measure_ADC_KEY,
+ #endif
SensorsReady, // Temperatures ready. Delay the next round of readings to let ADC pins settle.
StartupDelay // Startup, delay initial temp reading a tiny bit so the hardware can settle
};
@@ -272,6 +276,10 @@ class Temperature {
#endif
public:
+ #if ENABLED(ADC_KEYPAD)
+ static uint32_t current_ADCKey_raw;
+ static uint8_t ADCKey_count;
+ #endif
/**
* Instance Methods
diff --git a/Marlin/ultralcd.cpp b/Marlin/ultralcd.cpp
index ed26888db..808b6df49 100644
--- a/Marlin/ultralcd.cpp
+++ b/Marlin/ultralcd.cpp
@@ -3997,10 +3997,53 @@ void kill_screen(const char* lcd_msg) {
/**
*
- * Handlers for RepRap World Keypad input
+ * Handlers for Keypad input
*
*/
- #if ENABLED(REPRAPWORLD_KEYPAD)
+ #if ENABLED(ADC_KEYPAD)
+
+ inline void handle_adc_keypad() {
+ static uint8_t adc_steps = 0;
+ if (buttons_reprapworld_keypad) {
+ adc_steps++;
+ NOMORE(adc_steps, 20);
+
+ lcd_quick_feedback();
+ lcdDrawUpdate = LCDVIEW_REDRAW_NOW;
+ return_to_status_ms = millis() + LCD_TIMEOUT_TO_STATUS;
+ if (encoderDirection == -1) { // side effect which signals we are inside a menu
+ if (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_DOWN)
+ encoderPosition -= ENCODER_STEPS_PER_MENU_ITEM;
+ else if (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_UP)
+ encoderPosition += ENCODER_STEPS_PER_MENU_ITEM;
+ else if (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_LEFT)
+ menu_action_back();
+ else if (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_RIGHT)
+ // enqueue_and_echo_commands_P(PSTR("M0 Pause"));
+ lcd_return_to_status();
+ }
+ else {
+ const int8_t step = adc_steps > 19 ? 100 : adc_steps > 10 ? 10 : 1;
+ if (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_DOWN)
+ encoderPosition += ENCODER_PULSES_PER_STEP * step;
+ else if (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_UP)
+ encoderPosition -= ENCODER_PULSES_PER_STEP * step;
+ else if (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_RIGHT)
+ encoderPosition = 0;
+ }
+ #if ENABLED(ADC_KEYPAD_DEBUG)
+ SERIAL_PROTOCOLLNPAIR("buttons_reprapworld_keypad = ", (uint32_t)buttons_reprapworld_keypad);
+ SERIAL_PROTOCOLLNPAIR("encoderPosition = ", (uint32_t)encoderPosition);
+ #endif
+ }
+ else if (!thermalManager.current_ADCKey_raw) {
+ // reset stepping acceleration
+ adc_steps = 0;
+ }
+ }
+
+ #elif ENABLED(REPRAPWORLD_KEYPAD)
+
void _reprapworld_keypad_move(const AxisEnum axis, const int16_t dir) {
move_menu_scale = REPRAPWORLD_KEYPAD_MOVE_STEP;
encoderPosition = dir;
@@ -4111,7 +4154,7 @@ void lcd_init() {
SET_INPUT_PULLUP(BTN_ENC);
#endif
- #if ENABLED(REPRAPWORLD_KEYPAD)
+ #if ENABLED(REPRAPWORLD_KEYPAD) && DISABLED(ADC_KEYPAD)
SET_OUTPUT(SHIFT_CLK);
OUT_WRITE(SHIFT_LD, HIGH);
SET_INPUT_PULLUP(SHIFT_OUT);
@@ -4291,8 +4334,14 @@ void lcd_update() {
slow_buttons = lcd_implementation_read_slow_buttons(); // buttons which take too long to read in interrupt context
#endif
- #if ENABLED(REPRAPWORLD_KEYPAD)
+ #if ENABLED(ADC_KEYPAD)
+
+ handle_adc_keypad();
+
+ #elif ENABLED(REPRAPWORLD_KEYPAD)
+
handle_reprapworld_keypad();
+
#endif
bool encoderPastThreshold = (abs(encoderDiff) >= ENCODER_PULSES_PER_STEP);
@@ -4305,10 +4354,10 @@ void lcd_update() {
if (encoderRateMultiplierEnabled) {
int32_t encoderMovementSteps = abs(encoderDiff) / ENCODER_PULSES_PER_STEP;
- if (lastEncoderMovementMillis != 0) {
+ if (lastEncoderMovementMillis) {
// Note that the rate is always calculated between two passes through the
// loop and that the abs of the encoderDiff value is tracked.
- float encoderStepRate = (float)(encoderMovementSteps) / ((float)(ms - lastEncoderMovementMillis)) * 1000.0;
+ float encoderStepRate = float(encoderMovementSteps) / float(ms - lastEncoderMovementMillis) * 1000.0;
if (encoderStepRate >= ENCODER_100X_STEPS_PER_SEC) encoderMultiplier = 100;
else if (encoderStepRate >= ENCODER_10X_STEPS_PER_SEC) encoderMultiplier = 10;
@@ -4378,6 +4427,11 @@ void lcd_update() {
break;
} // switch
}
+
+ #if ENABLED(ADC_KEYPAD)
+ buttons_reprapworld_keypad = 0;
+ #endif
+
#if ENABLED(ULTIPANEL)
#define CURRENTSCREEN() (*currentScreen)(), lcd_clicked = false
#else
@@ -4625,9 +4679,23 @@ void lcd_reset_alert_level() { lcd_status_message_level = 0; }
#if ENABLED(LCD_HAS_SLOW_BUTTONS)
buttons |= slow_buttons;
#endif
- #if ENABLED(REPRAPWORLD_KEYPAD)
+
+ #if ENABLED(ADC_KEYPAD)
+
+ uint8_t newbutton_reprapworld_keypad = 0;
+ buttons = 0;
+ if (buttons_reprapworld_keypad == 0) {
+ newbutton_reprapworld_keypad = get_ADC_keyValue();
+ if (WITHIN(newbutton_reprapworld_keypad, 1, 8))
+ buttons_reprapworld_keypad = _BV(newbutton_reprapworld_keypad - 1);
+ }
+
+ #elif ENABLED(REPRAPWORLD_KEYPAD)
+
GET_BUTTON_STATES(buttons_reprapworld_keypad);
+
#endif
+
#else
GET_BUTTON_STATES(buttons);
#endif // !NEWPANEL
@@ -4693,4 +4761,42 @@ void lcd_reset_alert_level() { lcd_status_message_level = 0; }
#endif // ULTIPANEL
+#if ENABLED(ADC_KEYPAD)
+
+ typedef struct {
+ uint16_t ADCKeyValueMin, ADCKeyValueMax;
+ uint8_t ADCKeyNo;
+ } _stADCKeypadTable_;
+
+ static const _stADCKeypadTable_ stADCKeyTable[] = PROGMEM {
+ // VALUE_MIN, VALUE_MAX, KEY
+ { 4000, 4096, BLEN_REPRAPWORLD_KEYPAD_F1 + 1 }, // F1
+ { 4000, 4096, BLEN_REPRAPWORLD_KEYPAD_F2 + 1 }, // F2
+ { 4000, 4096, BLEN_REPRAPWORLD_KEYPAD_F3 + 1 }, // F3
+ { 300, 500, BLEN_REPRAPWORLD_KEYPAD_LEFT + 1 }, // LEFT
+ { 1900, 2200, BLEN_REPRAPWORLD_KEYPAD_RIGHT + 1 }, // RIGHT
+ { 570, 870, BLEN_REPRAPWORLD_KEYPAD_UP + 1 }, // UP
+ { 2670, 2870, BLEN_REPRAPWORLD_KEYPAD_DOWN + 1 }, // DOWN
+ { 1150, 1450, BLEN_REPRAPWORLD_KEYPAD_MIDDLE + 1 }, // ENTER
+ };
+
+ uint8_t get_ADC_keyValue(void) {
+ if (thermalManager.ADCKey_count >= 16) {
+ const uint16_t currentkpADCValue = thermalManager.current_ADCKey_raw >> 2;
+ #if ENABLED(ADC_KEYPAD_DEBUG)
+ SERIAL_PROTOCOLLN(currentkpADCValue);
+ #endif
+ thermalManager.current_ADCKey_raw = 0;
+ thermalManager.ADCKey_count = 0;
+ if (currentkpADCValue < 4000)
+ for (uint8_t i = 0; i < ADC_KEY_NUM; i++) {
+ const uint16_t lo = pgm_read_word(&stADCKeyTable[i].ADCKeyValueMin),
+ hi = pgm_read_word(&stADCKeyTable[i].ADCKeyValueMax);
+ if (WITHIN(currentkpADCValue, lo, hi)) return pgm_read_byte(&stADCKeyTable[i].ADCKeyNo);
+ }
+ }
+ return 0;
+ }
+#endif
+
#endif // ULTRA_LCD
diff --git a/Marlin/ultralcd.h b/Marlin/ultralcd.h
index eb6d2e5bf..2fb719bb8 100644
--- a/Marlin/ultralcd.h
+++ b/Marlin/ultralcd.h
@@ -57,6 +57,10 @@
void dontExpireStatus();
#endif
+ #if ENABLED(ADC_KEYPAD)
+ uint8_t get_ADC_keyValue();
+ #endif
+
#if ENABLED(DOGLCD)
extern uint16_t lcd_contrast;
void set_lcd_contrast(const uint16_t value);
@@ -130,6 +134,21 @@
#define REPRAPWORLD_KEYPAD_MOVE_Y_UP (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_UP)
#define REPRAPWORLD_KEYPAD_MOVE_X_LEFT (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_LEFT)
+ #if ENABLED(ADC_KEYPAD)
+ #define REPRAPWORLD_KEYPAD_MOVE_HOME (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_F1)
+ #define KEYPAD_EN_C EN_REPRAPWORLD_KEYPAD_MIDDLE
+ #else
+ #define REPRAPWORLD_KEYPAD_MOVE_HOME (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_MIDDLE)
+ #define KEYPAD_EN_C EN_REPRAPWORLD_KEYPAD_F1
+ #endif
+ #define REPRAPWORLD_KEYPAD_MOVE_MENU (buttons_reprapworld_keypad & KEYPAD_EN_C)
+
+ #if BUTTON_EXISTS(ENC)
+ #define LCD_CLICKED ((buttons & EN_C) || REPRAPWORLD_KEYPAD_MOVE_MENU)
+ #else
+ #define LCD_CLICKED REPRAPWORLD_KEYPAD_MOVE_MENU
+ #endif
+
#define REPRAPWORLD_KEYPAD_PRESSED (buttons_reprapworld_keypad & ( \
EN_REPRAPWORLD_KEYPAD_F3 | \
EN_REPRAPWORLD_KEYPAD_F2 | \
@@ -141,7 +160,6 @@
EN_REPRAPWORLD_KEYPAD_LEFT) \
)
- #define LCD_CLICKED ((buttons & EN_C) || (buttons_reprapworld_keypad & EN_REPRAPWORLD_KEYPAD_F1))
#elif ENABLED(NEWPANEL)
#define LCD_CLICKED (buttons & EN_C)
#else