diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 5da249fcc..c4fa028ce 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -853,11 +853,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. //#define FILAMENT_LCD_DISPLAY - - - - - #include "Configuration_adv.h" #include "thermistortables.h" diff --git a/Marlin/MarlinSerial.cpp b/Marlin/MarlinSerial.cpp index bd81bf51c..ad23a0620 100644 --- a/Marlin/MarlinSerial.cpp +++ b/Marlin/MarlinSerial.cpp @@ -78,7 +78,8 @@ void MarlinSerial::begin(long baud) { if (useU2X) { M_UCSRxA = BIT(M_U2Xx); baud_setting = (F_CPU / 4 / baud - 1) / 2; - } else { + } + else { M_UCSRxA = 0; baud_setting = (F_CPU / 8 / baud - 1) / 2; } diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp index 066845a32..4d29ebc7a 100644 --- a/Marlin/Marlin_main.cpp +++ b/Marlin/Marlin_main.cpp @@ -45,13 +45,16 @@ #include "stepper.h" #include "temperature.h" #include "cardreader.h" -#include "watchdog.h" #include "configuration_store.h" #include "language.h" #include "pins_arduino.h" #include "math.h" #include "buzzer.h" +#if ENABLED(USE_WATCHDOG) + #include "watchdog.h" +#endif + #if ENABLED(BLINKM) #include "blinkm.h" #include "Wire.h" @@ -681,7 +684,11 @@ void setup() { tp_init(); // Initialize temperature loop plan_init(); // Initialize planner; - watchdog_init(); + + #if ENABLED(USE_WATCHDOG) + watchdog_init(); + #endif + st_init(); // Initialize stepper, this enables interrupts! setup_photpin(); servo_init(); @@ -827,8 +834,10 @@ void get_command() { fromsd[cmd_queue_index_w] = false; #endif - char *npos = strchr(command, 'N'); - char *apos = strchr(command, '*'); + while (*command == ' ') command++; // skip any leading spaces + char* npos = (*command == 'N') ? command : NULL; // Require the N parameter to start the line + char* apos = strchr(command, '*'); + if (npos) { boolean M110 = strstr_P(command, PSTR("M110")) != NULL; @@ -1688,7 +1697,8 @@ static void setup_for_endstop_move() { if (a < b) { if (b < c) median = b; if (c < a) median = a; - } else { // b <= a + } + else { // b <= a if (c < b) median = b; if (a < c) median = a; } @@ -1783,7 +1793,8 @@ static void setup_for_endstop_move() { #endif do_blocking_move_to_x(X_MAX_POS + SLED_DOCKING_OFFSET + offset - 1); // Dock sled a bit closer to ensure proper capturing digitalWrite(SLED_PIN, LOW); // turn off magnet - } else { + } + else { float z_loc = current_position[Z_AXIS]; if (z_loc < Z_RAISE_BEFORE_PROBING + 5) z_loc = Z_RAISE_BEFORE_PROBING; do_blocking_move_to(X_MAX_POS + SLED_DOCKING_OFFSET + offset, current_position[Y_AXIS], z_loc); // this also updates current_position @@ -2696,7 +2707,8 @@ inline void gcode_G28() { SERIAL_PROTOCOLPGM("X out of range (1-" STRINGIFY(MESH_NUM_X_POINTS) ").\n"); return; } - } else { + } + else { SERIAL_PROTOCOLPGM("X not entered.\n"); return; } @@ -2706,7 +2718,8 @@ inline void gcode_G28() { SERIAL_PROTOCOLPGM("Y out of range (1-" STRINGIFY(MESH_NUM_Y_POINTS) ").\n"); return; } - } else { + } + else { SERIAL_PROTOCOLPGM("Y not entered.\n"); return; } @@ -4653,13 +4666,8 @@ inline void gcode_M220() { inline void gcode_M221() { if (code_seen('S')) { int sval = code_value(); - if (code_seen('T')) { - if (setTargetedHotend(221)) return; - extruder_multiplier[target_extruder] = sval; - } - else { - extruder_multiplier[active_extruder] = sval; - } + if (setTargetedHotend(221)) return; + extruder_multiplier[target_extruder] = sval; } } @@ -6381,25 +6389,29 @@ void mesh_plan_buffer_line(float x, float y, float z, const float e, float feed_ ny = current_position[Y_AXIS] + (y - current_position[Y_AXIS]) * normalized_dist; ne = current_position[E_AXIS] + (e - current_position[E_AXIS]) * normalized_dist; x_splits ^= BIT(ix); - } else if (ix < pix && (x_splits) & BIT(pix)) { + } + else if (ix < pix && (x_splits) & BIT(pix)) { nx = mbl.get_x(pix); normalized_dist = (nx - current_position[X_AXIS]) / (x - current_position[X_AXIS]); ny = current_position[Y_AXIS] + (y - current_position[Y_AXIS]) * normalized_dist; ne = current_position[E_AXIS] + (e - current_position[E_AXIS]) * normalized_dist; x_splits ^= BIT(pix); - } else if (iy > piy && (y_splits) & BIT(iy)) { + } + else if (iy > piy && (y_splits) & BIT(iy)) { ny = mbl.get_y(iy); normalized_dist = (ny - current_position[Y_AXIS]) / (y - current_position[Y_AXIS]); nx = current_position[X_AXIS] + (x - current_position[X_AXIS]) * normalized_dist; ne = current_position[E_AXIS] + (e - current_position[E_AXIS]) * normalized_dist; y_splits ^= BIT(iy); - } else if (iy < piy && (y_splits) & BIT(piy)) { + } + else if (iy < piy && (y_splits) & BIT(piy)) { ny = mbl.get_y(piy); normalized_dist = (ny - current_position[Y_AXIS]) / (y - current_position[Y_AXIS]); nx = current_position[X_AXIS] + (x - current_position[X_AXIS]) * normalized_dist; ne = current_position[E_AXIS] + (e - current_position[E_AXIS]) * normalized_dist; y_splits ^= BIT(piy); - } else { + } + else { // Already split on a border plan_buffer_line(x, y, z, e, feed_rate, extruder); set_current_to_destination(); diff --git a/Marlin/Sd2Card.cpp b/Marlin/Sd2Card.cpp index 5063d74ef..dbb025f5d 100644 --- a/Marlin/Sd2Card.cpp +++ b/Marlin/Sd2Card.cpp @@ -192,11 +192,13 @@ uint32_t Sd2Card::cardSize() { uint8_t c_size_mult = (csd.v1.c_size_mult_high << 1) | csd.v1.c_size_mult_low; return (uint32_t)(c_size + 1) << (c_size_mult + read_bl_len - 7); - } else if (csd.v2.csd_ver == 1) { + } + else if (csd.v2.csd_ver == 1) { uint32_t c_size = ((uint32_t)csd.v2.c_size_high << 16) | (csd.v2.c_size_mid << 8) | csd.v2.c_size_low; return (c_size + 1) << 10; - } else { + } + else { error(SD_CARD_ERROR_BAD_CSD); return 0; } diff --git a/Marlin/Sd2PinMap.h b/Marlin/Sd2PinMap.h index 7496ae641..94dbd6df7 100644 --- a/Marlin/Sd2PinMap.h +++ b/Marlin/Sd2PinMap.h @@ -396,7 +396,8 @@ static inline __attribute__((always_inline)) bool getPinMode(uint8_t pin) { if (__builtin_constant_p(pin) && pin < digitalPinCount) { return (*digitalPinMap[pin].ddr >> digitalPinMap[pin].bit) & 1; - } else { + } + else { return badPinNumber(); } } @@ -405,10 +406,12 @@ static inline __attribute__((always_inline)) if (__builtin_constant_p(pin) && pin < digitalPinCount) { if (mode) { *digitalPinMap[pin].ddr |= BIT(digitalPinMap[pin].bit); - } else { + } + else { *digitalPinMap[pin].ddr &= ~BIT(digitalPinMap[pin].bit); } - } else { + } + else { badPinNumber(); } } @@ -416,7 +419,8 @@ static inline __attribute__((always_inline)) bool fastDigitalRead(uint8_t pin) { if (__builtin_constant_p(pin) && pin < digitalPinCount) { return (*digitalPinMap[pin].pin >> digitalPinMap[pin].bit) & 1; - } else { + } + else { return badPinNumber(); } } @@ -425,10 +429,12 @@ static inline __attribute__((always_inline)) if (__builtin_constant_p(pin) && pin < digitalPinCount) { if (value) { *digitalPinMap[pin].port |= BIT(digitalPinMap[pin].bit); - } else { + } + else { *digitalPinMap[pin].port &= ~BIT(digitalPinMap[pin].bit); } - } else { + } + else { badPinNumber(); } } diff --git a/Marlin/configuration_store.cpp b/Marlin/configuration_store.cpp index e88c06f6d..3fcd64973 100644 --- a/Marlin/configuration_store.cpp +++ b/Marlin/configuration_store.cpp @@ -410,7 +410,7 @@ void Config_RetrieveSettings() { EEPROM_READ_VAR(i, dummy); // bedKp if (dummy != DUMMY_PID_VALUE) { - bedKp = dummy; + bedKp = dummy; UNUSED(bedKp); EEPROM_READ_VAR(i, bedKi); EEPROM_READ_VAR(i, bedKd); } @@ -540,7 +540,7 @@ void Config_ResetDefault() { #if ENABLED(PID_PARAMS_PER_EXTRUDER) for (int e = 0; e < EXTRUDERS; e++) #else - int e = 0; // only need to write once + int e = 0; UNUSED(e); // only need to write once #endif { PID_PARAM(Kp, e) = DEFAULT_Kp; diff --git a/Marlin/configurator/config/Configuration.h b/Marlin/configurator/config/Configuration.h index 8fc1c3129..3d00134fb 100644 --- a/Marlin/configurator/config/Configuration.h +++ b/Marlin/configurator/config/Configuration.h @@ -852,11 +852,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. //#define FILAMENT_LCD_DISPLAY - - - - - #include "Configuration_adv.h" #include "thermistortables.h" diff --git a/Marlin/dogm_lcd_implementation.h b/Marlin/dogm_lcd_implementation.h index 355ca834d..4e2cbf9ef 100644 --- a/Marlin/dogm_lcd_implementation.h +++ b/Marlin/dogm_lcd_implementation.h @@ -197,18 +197,20 @@ char lcd_printPGM(const char* str) { /* Warning: This function is called from interrupt context */ static void lcd_implementation_init() { - #if ENABLED(LCD_PIN_BL) // Enable LCD backlight + #if defined(LCD_PIN_BL) && LCD_PIN_BL > -1 // Enable LCD backlight pinMode(LCD_PIN_BL, OUTPUT); digitalWrite(LCD_PIN_BL, HIGH); #endif - #if ENABLED(LCD_PIN_RESET) + #if defined(LCD_PIN_RESET) && LCD_PIN_RESET > -1 pinMode(LCD_PIN_RESET, OUTPUT); digitalWrite(LCD_PIN_RESET, HIGH); #endif + #if DISABLED(MINIPANEL) // setContrast not working for Mini Panel u8g.setContrast(lcd_contrast); #endif + // FIXME: remove this workaround // Uncomment this if you have the first generation (V1.10) of STBs board // pinMode(17, OUTPUT); // Enable LCD backlight diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h index bf5eeb2f0..a3ffe2903 100644 --- a/Marlin/example_configurations/Felix/Configuration.h +++ b/Marlin/example_configurations/Felix/Configuration.h @@ -725,7 +725,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs //#define LCD_I2C_VIKI - + // SSD1306 OLED generic display support // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib //#define U8GLIB_SSD1306 @@ -835,11 +835,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. //#define FILAMENT_LCD_DISPLAY - - - - - #include "Configuration_adv.h" #include "thermistortables.h" diff --git a/Marlin/example_configurations/Felix/Configuration_DUAL.h b/Marlin/example_configurations/Felix/Configuration_DUAL.h index a64eba453..09adeae13 100644 --- a/Marlin/example_configurations/Felix/Configuration_DUAL.h +++ b/Marlin/example_configurations/Felix/Configuration_DUAL.h @@ -366,7 +366,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. #define FILAMENT_RUNOUT_SCRIPT "M600" #endif - + //=========================================================================== //=========================== Manual Bed Leveling =========================== //=========================================================================== @@ -459,7 +459,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine. // Useful to retract a deployable Z probe. - + //#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. @@ -799,11 +799,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. //#define FILAMENT_LCD_DISPLAY - - - - - #include "Configuration_adv.h" #include "thermistortables.h" diff --git a/Marlin/example_configurations/Felix/Configuration_adv.h b/Marlin/example_configurations/Felix/Configuration_adv.h index 8ae05cfbd..139c1fca2 100644 --- a/Marlin/example_configurations/Felix/Configuration_adv.h +++ b/Marlin/example_configurations/Felix/Configuration_adv.h @@ -145,7 +145,7 @@ #if ENABLED(Z_DUAL_STEPPER_DRIVERS) // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper. - // That way the machine is capable to align the bed during home, since both Z steppers are homed. + // That way the machine is capable to align the bed during home, since both Z steppers are homed. // There is also an implementation of M666 (software endstops adjustment) to this feature. // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed. // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2. @@ -343,8 +343,8 @@ // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT // we don't have a big font for Cyrillic, Kana //#define USE_BIG_EDIT_FONT - - // If you have spare 2300Byte of progmem and want to use a + + // If you have spare 2300Byte of progmem and want to use a // smaller font on the Info-screen uncomment the next line. //#define USE_SMALL_INFOFONT #endif // DOGLCD @@ -466,7 +466,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st #endif /******************************************************************************\ - * enable this section if you have TMC26X motor drivers. + * enable this section if you have TMC26X motor drivers. * you need to import the TMC26XStepper library into the arduino IDE for this ******************************************************************************/ @@ -479,56 +479,56 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps - + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps - + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps - + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms - #define Y2_MICROSTEPS 16 //number of microsteps - + #define Y2_MICROSTEPS 16 //number of microsteps + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps - + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps - + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps - + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms - #define E1_MICROSTEPS 16 //number of microsteps - + #define E1_MICROSTEPS 16 //number of microsteps + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms - #define E2_MICROSTEPS 16 //number of microsteps - + #define E2_MICROSTEPS 16 //number of microsteps + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms - #define E3_MICROSTEPS 16 //number of microsteps + #define E3_MICROSTEPS 16 //number of microsteps #endif /******************************************************************************\ - * enable this section if you have L6470 motor drivers. + * enable this section if you have L6470 motor drivers. * you need to import the L6470 library into the arduino IDE for this ******************************************************************************/ @@ -539,67 +539,64 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps - #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps - #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps - #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y2_IS_L6470 - #define Y2_MICROSTEPS 16 //number of microsteps - #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y2_MICROSTEPS 16 //number of microsteps + #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off - #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps - #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps - #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps - #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E1_IS_L6470 - #define E1_MICROSTEPS 16 //number of microsteps #define E1_MICROSTEPS 16 //number of microsteps - #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E2_IS_L6470 - #define E2_MICROSTEPS 16 //number of microsteps #define E2_MICROSTEPS 16 //number of microsteps - #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E3_IS_L6470 - #define E3_MICROSTEPS 16 //number of microsteps #define E3_MICROSTEPS 16 //number of microsteps - #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #endif #include "Conditionals.h" diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h index b61cf1988..519f3c789 100644 --- a/Marlin/example_configurations/Hephestos/Configuration.h +++ b/Marlin/example_configurations/Hephestos/Configuration.h @@ -79,7 +79,7 @@ Here are some standard links for getting your machine calibrated: // Added for BQ #define SOURCE_CODE_URL "http://www.bq.com/gb/downloads-prusa-i3-hephestos.html" - + // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" @@ -734,7 +734,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs //#define LCD_I2C_VIKI - + // SSD1306 OLED generic display support // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib //#define U8GLIB_SSD1306 @@ -844,11 +844,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. //#define FILAMENT_LCD_DISPLAY - - - - - #include "Configuration_adv.h" #include "thermistortables.h" diff --git a/Marlin/example_configurations/Hephestos/Configuration_adv.h b/Marlin/example_configurations/Hephestos/Configuration_adv.h index 5d25cd62a..9722db624 100644 --- a/Marlin/example_configurations/Hephestos/Configuration_adv.h +++ b/Marlin/example_configurations/Hephestos/Configuration_adv.h @@ -145,7 +145,7 @@ #if ENABLED(Z_DUAL_STEPPER_DRIVERS) // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper. - // That way the machine is capable to align the bed during home, since both Z steppers are homed. + // That way the machine is capable to align the bed during home, since both Z steppers are homed. // There is also an implementation of M666 (software endstops adjustment) to this feature. // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed. // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2. @@ -343,8 +343,8 @@ // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT // we don't have a big font for Cyrillic, Kana //#define USE_BIG_EDIT_FONT - - // If you have spare 2300Byte of progmem and want to use a + + // If you have spare 2300Byte of progmem and want to use a // smaller font on the Info-screen uncomment the next line. //#define USE_SMALL_INFOFONT #endif // DOGLCD @@ -466,7 +466,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st #endif /******************************************************************************\ - * enable this section if you have TMC26X motor drivers. + * enable this section if you have TMC26X motor drivers. * you need to import the TMC26XStepper library into the arduino IDE for this ******************************************************************************/ @@ -479,56 +479,56 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps - + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps - + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps - + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms - #define Y2_MICROSTEPS 16 //number of microsteps - + #define Y2_MICROSTEPS 16 //number of microsteps + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps - + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps - + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps - + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms - #define E1_MICROSTEPS 16 //number of microsteps - + #define E1_MICROSTEPS 16 //number of microsteps + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms - #define E2_MICROSTEPS 16 //number of microsteps - + #define E2_MICROSTEPS 16 //number of microsteps + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms - #define E3_MICROSTEPS 16 //number of microsteps + #define E3_MICROSTEPS 16 //number of microsteps #endif /******************************************************************************\ - * enable this section if you have L6470 motor drivers. + * enable this section if you have L6470 motor drivers. * you need to import the L6470 library into the arduino IDE for this ******************************************************************************/ @@ -539,67 +539,64 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps - #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps - #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps - #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y2_IS_L6470 - #define Y2_MICROSTEPS 16 //number of microsteps - #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y2_MICROSTEPS 16 //number of microsteps + #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off - #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps - #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps - #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps - #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E1_IS_L6470 - #define E1_MICROSTEPS 16 //number of microsteps #define E1_MICROSTEPS 16 //number of microsteps - #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E2_IS_L6470 - #define E2_MICROSTEPS 16 //number of microsteps #define E2_MICROSTEPS 16 //number of microsteps - #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E3_IS_L6470 - #define E3_MICROSTEPS 16 //number of microsteps #define E3_MICROSTEPS 16 //number of microsteps - #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #endif #include "Conditionals.h" diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h index ffa2ba953..66af2bbe9 100644 --- a/Marlin/example_configurations/K8200/Configuration.h +++ b/Marlin/example_configurations/K8200/Configuration.h @@ -730,7 +730,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs //#define LCD_I2C_VIKI - + // SSD1306 OLED generic display support // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib //#define U8GLIB_SSD1306 @@ -840,11 +840,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. //#define FILAMENT_LCD_DISPLAY - - - - - #include "Configuration_adv.h" #include "thermistortables.h" diff --git a/Marlin/example_configurations/K8200/Configuration_adv.h b/Marlin/example_configurations/K8200/Configuration_adv.h index d51ed247f..77717bc50 100644 --- a/Marlin/example_configurations/K8200/Configuration_adv.h +++ b/Marlin/example_configurations/K8200/Configuration_adv.h @@ -145,7 +145,7 @@ #if ENABLED(Z_DUAL_STEPPER_DRIVERS) // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper. - // That way the machine is capable to align the bed during home, since both Z steppers are homed. + // That way the machine is capable to align the bed during home, since both Z steppers are homed. // There is also an implementation of M666 (software endstops adjustment) to this feature. // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed. // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2. @@ -343,8 +343,8 @@ // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT // we don't have a big font for Cyrillic, Kana //#define USE_BIG_EDIT_FONT - - // If you have spare 2300Byte of progmem and want to use a + + // If you have spare 2300Byte of progmem and want to use a // smaller font on the Info-screen uncomment the next line. //#define USE_SMALL_INFOFONT #endif // DOGLCD @@ -466,7 +466,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st #endif /******************************************************************************\ - * enable this section if you have TMC26X motor drivers. + * enable this section if you have TMC26X motor drivers. * you need to import the TMC26XStepper library into the arduino IDE for this ******************************************************************************/ @@ -479,56 +479,56 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps - + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps - + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps - + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms - #define Y2_MICROSTEPS 16 //number of microsteps - + #define Y2_MICROSTEPS 16 //number of microsteps + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps - + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps - + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps - + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms - #define E1_MICROSTEPS 16 //number of microsteps - + #define E1_MICROSTEPS 16 //number of microsteps + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms - #define E2_MICROSTEPS 16 //number of microsteps - + #define E2_MICROSTEPS 16 //number of microsteps + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms - #define E3_MICROSTEPS 16 //number of microsteps + #define E3_MICROSTEPS 16 //number of microsteps #endif /******************************************************************************\ - * enable this section if you have L6470 motor drivers. + * enable this section if you have L6470 motor drivers. * you need to import the L6470 library into the arduino IDE for this ******************************************************************************/ @@ -539,67 +539,64 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps - #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps - #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps - #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y2_IS_L6470 - #define Y2_MICROSTEPS 16 //number of microsteps - #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y2_MICROSTEPS 16 //number of microsteps + #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off - #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps - #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps - #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps - #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E1_IS_L6470 - #define E1_MICROSTEPS 16 //number of microsteps #define E1_MICROSTEPS 16 //number of microsteps - #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E2_IS_L6470 - #define E2_MICROSTEPS 16 //number of microsteps #define E2_MICROSTEPS 16 //number of microsteps - #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E3_IS_L6470 - #define E3_MICROSTEPS 16 //number of microsteps #define E3_MICROSTEPS 16 //number of microsteps - #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #endif #include "Conditionals.h" diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h index 783410143..630830f70 100644 --- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h +++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h @@ -742,7 +742,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs //#define LCD_I2C_VIKI - + // SSD1306 OLED generic display support // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib //#define U8GLIB_SSD1306 @@ -852,11 +852,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. //#define FILAMENT_LCD_DISPLAY - - - - - #include "Configuration_adv.h" #include "thermistortables.h" diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h index d4a0b841f..7cd0f005c 100644 --- a/Marlin/example_configurations/RigidBot/Configuration.h +++ b/Marlin/example_configurations/RigidBot/Configuration.h @@ -732,7 +732,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs //#define LCD_I2C_VIKI - + // SSD1306 OLED generic display support // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib //#define U8GLIB_SSD1306 @@ -842,11 +842,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. //#define FILAMENT_LCD_DISPLAY - - - - - #include "Configuration_adv.h" #include "thermistortables.h" diff --git a/Marlin/example_configurations/RigidBot/Configuration_adv.h b/Marlin/example_configurations/RigidBot/Configuration_adv.h index 264a40401..f933c68fa 100644 --- a/Marlin/example_configurations/RigidBot/Configuration_adv.h +++ b/Marlin/example_configurations/RigidBot/Configuration_adv.h @@ -137,7 +137,7 @@ #if ENABLED(Z_DUAL_STEPPER_DRIVERS) // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper. - // That way the machine is capable to align the bed during home, since both Z steppers are homed. + // That way the machine is capable to align the bed during home, since both Z steppers are homed. // There is also an implementation of M666 (software endstops adjustment) to this feature. // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed. // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2. @@ -336,8 +336,8 @@ // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT // we don't have a big font for Cyrillic, Kana //#define USE_BIG_EDIT_FONT - - // If you have spare 2300Byte of progmem and want to use a + + // If you have spare 2300Byte of progmem and want to use a // smaller font on the Info-screen uncomment the next line. //#define USE_SMALL_INFOFONT #endif // DOGLCD @@ -461,7 +461,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st #endif /******************************************************************************\ - * enable this section if you have TMC26X motor drivers. + * enable this section if you have TMC26X motor drivers. * you need to import the TMC26XStepper library into the arduino IDE for this ******************************************************************************/ @@ -474,56 +474,56 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps - + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps - + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps - + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms - #define Y2_MICROSTEPS 16 //number of microsteps - + #define Y2_MICROSTEPS 16 //number of microsteps + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps - + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps - + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps - + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms - #define E1_MICROSTEPS 16 //number of microsteps - + #define E1_MICROSTEPS 16 //number of microsteps + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms - #define E2_MICROSTEPS 16 //number of microsteps - + #define E2_MICROSTEPS 16 //number of microsteps + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms - #define E3_MICROSTEPS 16 //number of microsteps + #define E3_MICROSTEPS 16 //number of microsteps #endif /******************************************************************************\ - * enable this section if you have L6470 motor drivers. + * enable this section if you have L6470 motor drivers. * you need to import the L6470 library into the arduino IDE for this ******************************************************************************/ @@ -534,67 +534,64 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps - #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps - #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps - #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y2_IS_L6470 - #define Y2_MICROSTEPS 16 //number of microsteps - #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y2_MICROSTEPS 16 //number of microsteps + #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off - #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps - #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps - #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps - #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E1_IS_L6470 - #define E1_MICROSTEPS 16 //number of microsteps #define E1_MICROSTEPS 16 //number of microsteps - #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E2_IS_L6470 - #define E2_MICROSTEPS 16 //number of microsteps #define E2_MICROSTEPS 16 //number of microsteps - #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E3_IS_L6470 - #define E3_MICROSTEPS 16 //number of microsteps #define E3_MICROSTEPS 16 //number of microsteps - #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #endif #include "Conditionals.h" diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h index 7e0e31d3c..068f93b8d 100644 --- a/Marlin/example_configurations/SCARA/Configuration.h +++ b/Marlin/example_configurations/SCARA/Configuration.h @@ -37,16 +37,16 @@ Here are some standard links for getting your machine calibrated: // QHARLEYS Autobedlevelling has not been ported, because Marlin has now Bed-levelling // You might need Z-Min endstop on SCARA-Printer to use this feature. Actually untested! // Uncomment to use Morgan scara mode -#define SCARA +#define SCARA #define SCARA_SEGMENTS_PER_SECOND 200 // If movement is choppy try lowering this value // Length of inner support arm #define Linkage_1 150 //mm Preprocessor cannot handle decimal point... -// Length of outer support arm Measure arm lengths precisely and enter -#define Linkage_2 150 //mm +// Length of outer support arm Measure arm lengths precisely and enter +#define Linkage_2 150 //mm -// SCARA tower offset (position of Tower relative to bed zero position) +// SCARA tower offset (position of Tower relative to bed zero position) // This needs to be reasonably accurate as it defines the printbed position in the SCARA space. -#define SCARA_offset_x 100 //mm +#define SCARA_offset_x 100 //mm #define SCARA_offset_y -56 //mm #define SCARA_RAD2DEG 57.2957795 // to convert RAD to degrees @@ -750,7 +750,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs //#define LCD_I2C_VIKI - + // SSD1306 OLED generic display support // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib //#define U8GLIB_SSD1306 @@ -860,11 +860,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. //#define FILAMENT_LCD_DISPLAY - - - - - #include "Configuration_adv.h" #include "thermistortables.h" diff --git a/Marlin/example_configurations/SCARA/Configuration_adv.h b/Marlin/example_configurations/SCARA/Configuration_adv.h index 2fa80655f..2a2ba71dd 100644 --- a/Marlin/example_configurations/SCARA/Configuration_adv.h +++ b/Marlin/example_configurations/SCARA/Configuration_adv.h @@ -145,7 +145,7 @@ #if ENABLED(Z_DUAL_STEPPER_DRIVERS) // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper. - // That way the machine is capable to align the bed during home, since both Z steppers are homed. + // That way the machine is capable to align the bed during home, since both Z steppers are homed. // There is also an implementation of M666 (software endstops adjustment) to this feature. // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed. // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2. @@ -343,8 +343,8 @@ // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT // we don't have a big font for Cyrillic, Kana //#define USE_BIG_EDIT_FONT - - // If you have spare 2300Byte of progmem and want to use a + + // If you have spare 2300Byte of progmem and want to use a // smaller font on the Info-screen uncomment the next line. //#define USE_SMALL_INFOFONT #endif // DOGLCD @@ -466,7 +466,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st #endif /******************************************************************************\ - * enable this section if you have TMC26X motor drivers. + * enable this section if you have TMC26X motor drivers. * you need to import the TMC26XStepper library into the arduino IDE for this ******************************************************************************/ @@ -479,56 +479,56 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps - + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps - + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps - + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms - #define Y2_MICROSTEPS 16 //number of microsteps - + #define Y2_MICROSTEPS 16 //number of microsteps + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps - + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps - + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps - + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms - #define E1_MICROSTEPS 16 //number of microsteps - + #define E1_MICROSTEPS 16 //number of microsteps + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms - #define E2_MICROSTEPS 16 //number of microsteps - + #define E2_MICROSTEPS 16 //number of microsteps + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms - #define E3_MICROSTEPS 16 //number of microsteps + #define E3_MICROSTEPS 16 //number of microsteps #endif /******************************************************************************\ - * enable this section if you have L6470 motor drivers. + * enable this section if you have L6470 motor drivers. * you need to import the L6470 library into the arduino IDE for this ******************************************************************************/ @@ -539,67 +539,64 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps - #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps - #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps - #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y2_IS_L6470 - #define Y2_MICROSTEPS 16 //number of microsteps - #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y2_MICROSTEPS 16 //number of microsteps + #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off - #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps - #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps - #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps - #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E1_IS_L6470 - #define E1_MICROSTEPS 16 //number of microsteps #define E1_MICROSTEPS 16 //number of microsteps - #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E2_IS_L6470 - #define E2_MICROSTEPS 16 //number of microsteps #define E2_MICROSTEPS 16 //number of microsteps - #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E3_IS_L6470 - #define E3_MICROSTEPS 16 //number of microsteps #define E3_MICROSTEPS 16 //number of microsteps - #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #endif #include "Conditionals.h" diff --git a/Marlin/example_configurations/TAZ4/Configuration.h b/Marlin/example_configurations/TAZ4/Configuration.h index 9610488d7..1c42c6579 100644 --- a/Marlin/example_configurations/TAZ4/Configuration.h +++ b/Marlin/example_configurations/TAZ4/Configuration.h @@ -761,7 +761,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs //#define LCD_I2C_VIKI - + // SSD1306 OLED generic display support // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib //#define U8GLIB_SSD1306 @@ -871,11 +871,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. //#define FILAMENT_LCD_DISPLAY - - - - - #include "Configuration_adv.h" #include "thermistortables.h" diff --git a/Marlin/example_configurations/TAZ4/Configuration_adv.h b/Marlin/example_configurations/TAZ4/Configuration_adv.h index ffc126fb1..abbc59631 100644 --- a/Marlin/example_configurations/TAZ4/Configuration_adv.h +++ b/Marlin/example_configurations/TAZ4/Configuration_adv.h @@ -145,7 +145,7 @@ #if ENABLED(Z_DUAL_STEPPER_DRIVERS) // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper. - // That way the machine is capable to align the bed during home, since both Z steppers are homed. + // That way the machine is capable to align the bed during home, since both Z steppers are homed. // There is also an implementation of M666 (software endstops adjustment) to this feature. // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed. // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2. @@ -343,8 +343,8 @@ // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT // we don't have a big font for Cyrillic, Kana //#define USE_BIG_EDIT_FONT - - // If you have spare 2300Byte of progmem and want to use a + + // If you have spare 2300Byte of progmem and want to use a // smaller font on the Info-screen uncomment the next line. //#define USE_SMALL_INFOFONT #endif // DOGLCD @@ -469,7 +469,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st #endif /******************************************************************************\ - * enable this section if you have TMC26X motor drivers. + * enable this section if you have TMC26X motor drivers. * you need to import the TMC26XStepper library into the arduino IDE for this ******************************************************************************/ @@ -482,56 +482,56 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps - + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps - + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps - + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms - #define Y2_MICROSTEPS 16 //number of microsteps - + #define Y2_MICROSTEPS 16 //number of microsteps + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps - + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps - + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps - + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms - #define E1_MICROSTEPS 16 //number of microsteps - + #define E1_MICROSTEPS 16 //number of microsteps + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms - #define E2_MICROSTEPS 16 //number of microsteps - + #define E2_MICROSTEPS 16 //number of microsteps + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms - #define E3_MICROSTEPS 16 //number of microsteps + #define E3_MICROSTEPS 16 //number of microsteps #endif /******************************************************************************\ - * enable this section if you have L6470 motor drivers. + * enable this section if you have L6470 motor drivers. * you need to import the L6470 library into the arduino IDE for this ******************************************************************************/ @@ -542,67 +542,64 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps - #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps - #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps - #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y2_IS_L6470 - #define Y2_MICROSTEPS 16 //number of microsteps - #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y2_MICROSTEPS 16 //number of microsteps + #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off - #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps - #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps - #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps - #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E1_IS_L6470 - #define E1_MICROSTEPS 16 //number of microsteps #define E1_MICROSTEPS 16 //number of microsteps - #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E2_IS_L6470 - #define E2_MICROSTEPS 16 //number of microsteps #define E2_MICROSTEPS 16 //number of microsteps - #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E3_IS_L6470 - #define E3_MICROSTEPS 16 //number of microsteps #define E3_MICROSTEPS 16 //number of microsteps - #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #endif #include "Conditionals.h" diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h index d6775586e..f0666e74d 100644 --- a/Marlin/example_configurations/WITBOX/Configuration.h +++ b/Marlin/example_configurations/WITBOX/Configuration.h @@ -733,7 +733,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs //#define LCD_I2C_VIKI - + // SSD1306 OLED generic display support // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib //#define U8GLIB_SSD1306 @@ -843,11 +843,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. //#define FILAMENT_LCD_DISPLAY - - - - - #include "Configuration_adv.h" #include "thermistortables.h" diff --git a/Marlin/example_configurations/WITBOX/Configuration_adv.h b/Marlin/example_configurations/WITBOX/Configuration_adv.h index 2036af08c..a19cf4dd0 100644 --- a/Marlin/example_configurations/WITBOX/Configuration_adv.h +++ b/Marlin/example_configurations/WITBOX/Configuration_adv.h @@ -145,7 +145,7 @@ #if ENABLED(Z_DUAL_STEPPER_DRIVERS) // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper. - // That way the machine is capable to align the bed during home, since both Z steppers are homed. + // That way the machine is capable to align the bed during home, since both Z steppers are homed. // There is also an implementation of M666 (software endstops adjustment) to this feature. // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed. // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2. @@ -343,8 +343,8 @@ // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT // we don't have a big font for Cyrillic, Kana //#define USE_BIG_EDIT_FONT - - // If you have spare 2300Byte of progmem and want to use a + + // If you have spare 2300Byte of progmem and want to use a // smaller font on the Info-screen uncomment the next line. //#define USE_SMALL_INFOFONT #endif // DOGLCD @@ -466,7 +466,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st #endif /******************************************************************************\ - * enable this section if you have TMC26X motor drivers. + * enable this section if you have TMC26X motor drivers. * you need to import the TMC26XStepper library into the arduino IDE for this ******************************************************************************/ @@ -479,56 +479,56 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps - + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps - + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps - + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms - #define Y2_MICROSTEPS 16 //number of microsteps - + #define Y2_MICROSTEPS 16 //number of microsteps + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps - + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps - + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps - + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms - #define E1_MICROSTEPS 16 //number of microsteps - + #define E1_MICROSTEPS 16 //number of microsteps + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms - #define E2_MICROSTEPS 16 //number of microsteps - + #define E2_MICROSTEPS 16 //number of microsteps + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms - #define E3_MICROSTEPS 16 //number of microsteps + #define E3_MICROSTEPS 16 //number of microsteps #endif /******************************************************************************\ - * enable this section if you have L6470 motor drivers. + * enable this section if you have L6470 motor drivers. * you need to import the L6470 library into the arduino IDE for this ******************************************************************************/ @@ -539,67 +539,64 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps - #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps - #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps - #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y2_IS_L6470 - #define Y2_MICROSTEPS 16 //number of microsteps - #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y2_MICROSTEPS 16 //number of microsteps + #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off - #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps - #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps - #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps - #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E1_IS_L6470 - #define E1_MICROSTEPS 16 //number of microsteps #define E1_MICROSTEPS 16 //number of microsteps - #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E2_IS_L6470 - #define E2_MICROSTEPS 16 //number of microsteps #define E2_MICROSTEPS 16 //number of microsteps - #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E3_IS_L6470 - #define E3_MICROSTEPS 16 //number of microsteps #define E3_MICROSTEPS 16 //number of microsteps - #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #endif #include "Conditionals.h" diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h index 048e8b050..e3cf3a338 100644 --- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h +++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h @@ -742,7 +742,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs //#define LCD_I2C_VIKI - + // SSD1306 OLED generic display support // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib //#define U8GLIB_SSD1306 @@ -852,11 +852,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. //#define FILAMENT_LCD_DISPLAY - - - - - #include "Configuration_adv.h" #include "thermistortables.h" diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration.h b/Marlin/example_configurations/delta/biv2.5/Configuration.h index 6108b4eff..156537592 100644 --- a/Marlin/example_configurations/delta/biv2.5/Configuration.h +++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h @@ -867,7 +867,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs //#define LCD_I2C_VIKI - + // SSD1306 OLED generic display support // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib //#define U8GLIB_SSD1306 @@ -977,11 +977,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. //#define FILAMENT_LCD_DISPLAY - - - - - #include "Configuration_adv.h" #include "thermistortables.h" diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h index 3dc7c222d..b80ae83a7 100644 --- a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h +++ b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h @@ -145,7 +145,7 @@ #if ENABLED(Z_DUAL_STEPPER_DRIVERS) // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper. - // That way the machine is capable to align the bed during home, since both Z steppers are homed. + // That way the machine is capable to align the bed during home, since both Z steppers are homed. // There is also an implementation of M666 (software endstops adjustment) to this feature. // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed. // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2. @@ -345,8 +345,8 @@ // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT // we don't have a big font for Cyrillic, Kana //#define USE_BIG_EDIT_FONT - - // If you have spare 2300Byte of progmem and want to use a + + // If you have spare 2300Byte of progmem and want to use a // smaller font on the Info-screen uncomment the next line. //#define USE_SMALL_INFOFONT #endif // DOGLCD @@ -467,7 +467,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st #endif /******************************************************************************\ - * enable this section if you have TMC26X motor drivers. + * enable this section if you have TMC26X motor drivers. * you need to import the TMC26XStepper library into the arduino IDE for this ******************************************************************************/ @@ -480,56 +480,56 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps - + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps - + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps - + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms - #define Y2_MICROSTEPS 16 //number of microsteps - + #define Y2_MICROSTEPS 16 //number of microsteps + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps - + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps - + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps - + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms - #define E1_MICROSTEPS 16 //number of microsteps - + #define E1_MICROSTEPS 16 //number of microsteps + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms - #define E2_MICROSTEPS 16 //number of microsteps - + #define E2_MICROSTEPS 16 //number of microsteps + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms - #define E3_MICROSTEPS 16 //number of microsteps + #define E3_MICROSTEPS 16 //number of microsteps #endif /******************************************************************************\ - * enable this section if you have L6470 motor drivers. + * enable this section if you have L6470 motor drivers. * you need to import the L6470 library into the arduino IDE for this ******************************************************************************/ @@ -540,67 +540,64 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps - #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps - #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps - #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y2_IS_L6470 - #define Y2_MICROSTEPS 16 //number of microsteps - #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y2_MICROSTEPS 16 //number of microsteps + #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off - #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps - #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps - #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps - #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E1_IS_L6470 - #define E1_MICROSTEPS 16 //number of microsteps #define E1_MICROSTEPS 16 //number of microsteps - #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E2_IS_L6470 - #define E2_MICROSTEPS 16 //number of microsteps #define E2_MICROSTEPS 16 //number of microsteps - #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E3_IS_L6470 - #define E3_MICROSTEPS 16 //number of microsteps #define E3_MICROSTEPS 16 //number of microsteps - #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #endif #include "Conditionals.h" diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h index 84f18c02a..6776940b2 100644 --- a/Marlin/example_configurations/delta/generic/Configuration.h +++ b/Marlin/example_configurations/delta/generic/Configuration.h @@ -872,7 +872,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs //#define LCD_I2C_VIKI - + // SSD1306 OLED generic display support // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib //#define U8GLIB_SSD1306 @@ -982,11 +982,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. //#define FILAMENT_LCD_DISPLAY - - - - - #include "Configuration_adv.h" #include "thermistortables.h" diff --git a/Marlin/example_configurations/delta/generic/Configuration_adv.h b/Marlin/example_configurations/delta/generic/Configuration_adv.h index 2426f2bf4..8212e7689 100644 --- a/Marlin/example_configurations/delta/generic/Configuration_adv.h +++ b/Marlin/example_configurations/delta/generic/Configuration_adv.h @@ -145,7 +145,7 @@ #if ENABLED(Z_DUAL_STEPPER_DRIVERS) // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper. - // That way the machine is capable to align the bed during home, since both Z steppers are homed. + // That way the machine is capable to align the bed during home, since both Z steppers are homed. // There is also an implementation of M666 (software endstops adjustment) to this feature. // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed. // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2. @@ -345,8 +345,8 @@ // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT // we don't have a big font for Cyrillic, Kana //#define USE_BIG_EDIT_FONT - - // If you have spare 2300Byte of progmem and want to use a + + // If you have spare 2300Byte of progmem and want to use a // smaller font on the Info-screen uncomment the next line. //#define USE_SMALL_INFOFONT #endif // DOGLCD @@ -468,7 +468,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st #endif /******************************************************************************\ - * enable this section if you have TMC26X motor drivers. + * enable this section if you have TMC26X motor drivers. * you need to import the TMC26XStepper library into the arduino IDE for this ******************************************************************************/ @@ -481,56 +481,56 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps - + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps - + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps - + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms - #define Y2_MICROSTEPS 16 //number of microsteps - + #define Y2_MICROSTEPS 16 //number of microsteps + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps - + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps - + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps - + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms - #define E1_MICROSTEPS 16 //number of microsteps - + #define E1_MICROSTEPS 16 //number of microsteps + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms - #define E2_MICROSTEPS 16 //number of microsteps - + #define E2_MICROSTEPS 16 //number of microsteps + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms - #define E3_MICROSTEPS 16 //number of microsteps + #define E3_MICROSTEPS 16 //number of microsteps #endif /******************************************************************************\ - * enable this section if you have L6470 motor drivers. + * enable this section if you have L6470 motor drivers. * you need to import the L6470 library into the arduino IDE for this ******************************************************************************/ @@ -541,67 +541,64 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps - #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps - #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps - #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y2_IS_L6470 - #define Y2_MICROSTEPS 16 //number of microsteps - #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y2_MICROSTEPS 16 //number of microsteps + #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off - #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps - #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps - #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps - #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E1_IS_L6470 - #define E1_MICROSTEPS 16 //number of microsteps #define E1_MICROSTEPS 16 //number of microsteps - #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E2_IS_L6470 - #define E2_MICROSTEPS 16 //number of microsteps #define E2_MICROSTEPS 16 //number of microsteps - #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E3_IS_L6470 - #define E3_MICROSTEPS 16 //number of microsteps #define E3_MICROSTEPS 16 //number of microsteps - #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #endif #include "Conditionals.h" diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h index 0313d9957..4167bd419 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h @@ -872,7 +872,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs //#define LCD_I2C_VIKI - + // SSD1306 OLED generic display support // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib //#define U8GLIB_SSD1306 @@ -982,11 +982,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. //#define FILAMENT_LCD_DISPLAY - - - - - #include "Configuration_adv.h" #include "thermistortables.h" diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h index ee2437868..ef31f06f8 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h @@ -145,7 +145,7 @@ #if ENABLED(Z_DUAL_STEPPER_DRIVERS) // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper. - // That way the machine is capable to align the bed during home, since both Z steppers are homed. + // That way the machine is capable to align the bed during home, since both Z steppers are homed. // There is also an implementation of M666 (software endstops adjustment) to this feature. // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed. // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2. @@ -344,8 +344,8 @@ // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT // we don't have a big font for Cyrillic, Kana //#define USE_BIG_EDIT_FONT - - // If you have spare 2300Byte of progmem and want to use a + + // If you have spare 2300Byte of progmem and want to use a // smaller font on the Info-screen uncomment the next line. //#define USE_SMALL_INFOFONT #endif // DOGLCD @@ -467,7 +467,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st #endif /******************************************************************************\ - * enable this section if you have TMC26X motor drivers. + * enable this section if you have TMC26X motor drivers. * you need to import the TMC26XStepper library into the arduino IDE for this ******************************************************************************/ @@ -480,56 +480,56 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps - + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps - + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps - + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms - #define Y2_MICROSTEPS 16 //number of microsteps - + #define Y2_MICROSTEPS 16 //number of microsteps + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps - + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps - + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps - + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms - #define E1_MICROSTEPS 16 //number of microsteps - + #define E1_MICROSTEPS 16 //number of microsteps + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms - #define E2_MICROSTEPS 16 //number of microsteps - + #define E2_MICROSTEPS 16 //number of microsteps + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms - #define E3_MICROSTEPS 16 //number of microsteps + #define E3_MICROSTEPS 16 //number of microsteps #endif /******************************************************************************\ - * enable this section if you have L6470 motor drivers. + * enable this section if you have L6470 motor drivers. * you need to import the L6470 library into the arduino IDE for this ******************************************************************************/ @@ -540,67 +540,64 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps - #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps - #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps - #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y2_IS_L6470 - #define Y2_MICROSTEPS 16 //number of microsteps - #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y2_MICROSTEPS 16 //number of microsteps + #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off - #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps - #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps - #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps - #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E1_IS_L6470 - #define E1_MICROSTEPS 16 //number of microsteps #define E1_MICROSTEPS 16 //number of microsteps - #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E2_IS_L6470 - #define E2_MICROSTEPS 16 //number of microsteps #define E2_MICROSTEPS 16 //number of microsteps - #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E3_IS_L6470 - #define E3_MICROSTEPS 16 //number of microsteps #define E3_MICROSTEPS 16 //number of microsteps - #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #endif #include "Conditionals.h" diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h index eb4f59724..b47dab659 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h @@ -862,7 +862,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs //#define LCD_I2C_VIKI - + // SSD1306 OLED generic display support // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib //#define U8GLIB_SSD1306 @@ -972,11 +972,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. //#define FILAMENT_LCD_DISPLAY - - - - - #include "Configuration_adv.h" #include "thermistortables.h" diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h index 372328bb0..31541c90b 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h @@ -149,7 +149,7 @@ #if ENABLED(Z_DUAL_STEPPER_DRIVERS) // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper. - // That way the machine is capable to align the bed during home, since both Z steppers are homed. + // That way the machine is capable to align the bed during home, since both Z steppers are homed. // There is also an implementation of M666 (software endstops adjustment) to this feature. // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed. // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2. @@ -348,8 +348,8 @@ // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT // we don't have a big font for Cyrillic, Kana //#define USE_BIG_EDIT_FONT - - // If you have spare 2300Byte of progmem and want to use a + + // If you have spare 2300Byte of progmem and want to use a // smaller font on the Info-screen uncomment the next line. //#define USE_SMALL_INFOFONT #endif // DOGLCD @@ -471,7 +471,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st #endif /******************************************************************************\ - * enable this section if you have TMC26X motor drivers. + * enable this section if you have TMC26X motor drivers. * you need to import the TMC26XStepper library into the arduino IDE for this ******************************************************************************/ @@ -484,56 +484,56 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps - + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps - + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps - + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms - #define Y2_MICROSTEPS 16 //number of microsteps - + #define Y2_MICROSTEPS 16 //number of microsteps + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps - + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps - + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps - + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms - #define E1_MICROSTEPS 16 //number of microsteps - + #define E1_MICROSTEPS 16 //number of microsteps + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms - #define E2_MICROSTEPS 16 //number of microsteps - + #define E2_MICROSTEPS 16 //number of microsteps + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms - #define E3_MICROSTEPS 16 //number of microsteps + #define E3_MICROSTEPS 16 //number of microsteps #endif /******************************************************************************\ - * enable this section if you have L6470 motor drivers. + * enable this section if you have L6470 motor drivers. * you need to import the L6470 library into the arduino IDE for this ******************************************************************************/ @@ -544,67 +544,64 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps - #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps - #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps - #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y2_IS_L6470 - #define Y2_MICROSTEPS 16 //number of microsteps - #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y2_MICROSTEPS 16 //number of microsteps + #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off - #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps - #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps - #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps - #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E1_IS_L6470 - #define E1_MICROSTEPS 16 //number of microsteps #define E1_MICROSTEPS 16 //number of microsteps - #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E2_IS_L6470 - #define E2_MICROSTEPS 16 //number of microsteps #define E2_MICROSTEPS 16 //number of microsteps - #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E3_IS_L6470 - #define E3_MICROSTEPS 16 //number of microsteps #define E3_MICROSTEPS 16 //number of microsteps - #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #endif #include "Conditionals.h" diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h index d2870e807..bc74b6dc0 100644 --- a/Marlin/example_configurations/makibox/Configuration.h +++ b/Marlin/example_configurations/makibox/Configuration.h @@ -590,7 +590,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // default settings #define DEFAULT_AXIS_STEPS_PER_UNIT {400, 400, 400, 163} // default steps per unit for ***** MakiBox A6 ***** -#define DEFAULT_MAX_FEEDRATE {60, 60, 20, 45} // (mm/sec) +#define DEFAULT_MAX_FEEDRATE {60, 60, 20, 45} // (mm/sec) #define DEFAULT_MAX_ACCELERATION {2000,2000,30,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot. #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves @@ -744,7 +744,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs //#define LCD_I2C_VIKI - + // SSD1306 OLED generic display support // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib //#define U8GLIB_SSD1306 @@ -854,11 +854,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. //#define FILAMENT_LCD_DISPLAY - - - - - #include "Configuration_adv.h" #include "thermistortables.h" diff --git a/Marlin/example_configurations/makibox/Configuration_adv.h b/Marlin/example_configurations/makibox/Configuration_adv.h index ef9c9c140..4e62ab84d 100644 --- a/Marlin/example_configurations/makibox/Configuration_adv.h +++ b/Marlin/example_configurations/makibox/Configuration_adv.h @@ -145,7 +145,7 @@ #if ENABLED(Z_DUAL_STEPPER_DRIVERS) // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper. - // That way the machine is capable to align the bed during home, since both Z steppers are homed. + // That way the machine is capable to align the bed during home, since both Z steppers are homed. // There is also an implementation of M666 (software endstops adjustment) to this feature. // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed. // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2. @@ -342,8 +342,8 @@ // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT // we don't have a big font for Cyrillic, Kana //#define USE_BIG_EDIT_FONT - - // If you have spare 2300Byte of progmem and want to use a + + // If you have spare 2300Byte of progmem and want to use a // smaller font on the Info-screen uncomment the next line. //#define USE_SMALL_INFOFONT #endif // DOGLCD @@ -465,7 +465,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st #endif /******************************************************************************\ - * enable this section if you have TMC26X motor drivers. + * enable this section if you have TMC26X motor drivers. * you need to import the TMC26XStepper library into the arduino IDE for this ******************************************************************************/ @@ -478,56 +478,56 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps - + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps - + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps - + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms - #define Y2_MICROSTEPS 16 //number of microsteps - + #define Y2_MICROSTEPS 16 //number of microsteps + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps - + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps - + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps - + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms - #define E1_MICROSTEPS 16 //number of microsteps - + #define E1_MICROSTEPS 16 //number of microsteps + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms - #define E2_MICROSTEPS 16 //number of microsteps - + #define E2_MICROSTEPS 16 //number of microsteps + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms - #define E3_MICROSTEPS 16 //number of microsteps + #define E3_MICROSTEPS 16 //number of microsteps #endif /******************************************************************************\ - * enable this section if you have L6470 motor drivers. + * enable this section if you have L6470 motor drivers. * you need to import the L6470 library into the arduino IDE for this ******************************************************************************/ @@ -538,67 +538,64 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps - #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps - #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps - #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y2_IS_L6470 - #define Y2_MICROSTEPS 16 //number of microsteps - #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y2_MICROSTEPS 16 //number of microsteps + #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off - #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps - #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps - #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps - #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E1_IS_L6470 - #define E1_MICROSTEPS 16 //number of microsteps #define E1_MICROSTEPS 16 //number of microsteps - #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E2_IS_L6470 - #define E2_MICROSTEPS 16 //number of microsteps #define E2_MICROSTEPS 16 //number of microsteps - #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E3_IS_L6470 - #define E3_MICROSTEPS 16 //number of microsteps #define E3_MICROSTEPS 16 //number of microsteps - #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #endif #include "Conditionals.h" diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h index 7d0f11357..2636192d1 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h @@ -581,7 +581,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //#define DEFAULT_AXIS_STEPS_PER_UNIT {81.26, 80.01, 2561, 599.14} // Michel TVRR old //#define DEFAULT_AXIS_STEPS_PER_UNIT {71.1, 71.1, 2560, 739.65} // Michel TVRR #define DEFAULT_AXIS_STEPS_PER_UNIT {71.1, 71.1, 2560, 600} // David TVRR -#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 45} // (mm/sec) David TVRR +#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 45} // (mm/sec) David TVRR #define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. /* MICHEL: This has an impact on the "ripples" in print walls */ @@ -737,7 +737,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs //#define LCD_I2C_VIKI - + // SSD1306 OLED generic display support // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib //#define U8GLIB_SSD1306 @@ -847,11 +847,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. //#define FILAMENT_LCD_DISPLAY - - - - - #include "Configuration_adv.h" #include "thermistortables.h" diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h index c1c9313dd..f5b6a7e19 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h @@ -145,7 +145,7 @@ #if ENABLED(Z_DUAL_STEPPER_DRIVERS) // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper. - // That way the machine is capable to align the bed during home, since both Z steppers are homed. + // That way the machine is capable to align the bed during home, since both Z steppers are homed. // There is also an implementation of M666 (software endstops adjustment) to this feature. // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed. // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2. @@ -343,8 +343,8 @@ // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT // we don't have a big font for Cyrillic, Kana //#define USE_BIG_EDIT_FONT - - // If you have spare 2300Byte of progmem and want to use a + + // If you have spare 2300Byte of progmem and want to use a // smaller font on the Info-screen uncomment the next line. //#define USE_SMALL_INFOFONT #endif // DOGLCD @@ -466,7 +466,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st #endif /******************************************************************************\ - * enable this section if you have TMC26X motor drivers. + * enable this section if you have TMC26X motor drivers. * you need to import the TMC26XStepper library into the arduino IDE for this ******************************************************************************/ @@ -479,56 +479,56 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define X_MAX_CURRENT 1000 //in mA #define X_SENSE_RESISTOR 91 //in mOhms #define X_MICROSTEPS 16 //number of microsteps - + //#define X2_IS_TMC #define X2_MAX_CURRENT 1000 //in mA #define X2_SENSE_RESISTOR 91 //in mOhms #define X2_MICROSTEPS 16 //number of microsteps - + //#define Y_IS_TMC #define Y_MAX_CURRENT 1000 //in mA #define Y_SENSE_RESISTOR 91 //in mOhms #define Y_MICROSTEPS 16 //number of microsteps - + //#define Y2_IS_TMC #define Y2_MAX_CURRENT 1000 //in mA #define Y2_SENSE_RESISTOR 91 //in mOhms - #define Y2_MICROSTEPS 16 //number of microsteps - + #define Y2_MICROSTEPS 16 //number of microsteps + //#define Z_IS_TMC #define Z_MAX_CURRENT 1000 //in mA #define Z_SENSE_RESISTOR 91 //in mOhms #define Z_MICROSTEPS 16 //number of microsteps - + //#define Z2_IS_TMC #define Z2_MAX_CURRENT 1000 //in mA #define Z2_SENSE_RESISTOR 91 //in mOhms #define Z2_MICROSTEPS 16 //number of microsteps - + //#define E0_IS_TMC #define E0_MAX_CURRENT 1000 //in mA #define E0_SENSE_RESISTOR 91 //in mOhms #define E0_MICROSTEPS 16 //number of microsteps - + //#define E1_IS_TMC #define E1_MAX_CURRENT 1000 //in mA #define E1_SENSE_RESISTOR 91 //in mOhms - #define E1_MICROSTEPS 16 //number of microsteps - + #define E1_MICROSTEPS 16 //number of microsteps + //#define E2_IS_TMC #define E2_MAX_CURRENT 1000 //in mA #define E2_SENSE_RESISTOR 91 //in mOhms - #define E2_MICROSTEPS 16 //number of microsteps - + #define E2_MICROSTEPS 16 //number of microsteps + //#define E3_IS_TMC #define E3_MAX_CURRENT 1000 //in mA #define E3_SENSE_RESISTOR 91 //in mOhms - #define E3_MICROSTEPS 16 //number of microsteps + #define E3_MICROSTEPS 16 //number of microsteps #endif /******************************************************************************\ - * enable this section if you have L6470 motor drivers. + * enable this section if you have L6470 motor drivers. * you need to import the L6470 library into the arduino IDE for this ******************************************************************************/ @@ -539,67 +539,64 @@ const unsigned int dropsegments=5; //everything with less than this number of st //#define X_IS_L6470 #define X_MICROSTEPS 16 //number of microsteps - #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define X2_IS_L6470 #define X2_MICROSTEPS 16 //number of microsteps - #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y_IS_L6470 #define Y_MICROSTEPS 16 //number of microsteps - #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Y2_IS_L6470 - #define Y2_MICROSTEPS 16 //number of microsteps - #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Y2_MICROSTEPS 16 //number of microsteps + #define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off - #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall + //#define Z_IS_L6470 #define Z_MICROSTEPS 16 //number of microsteps - #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define Z2_IS_L6470 #define Z2_MICROSTEPS 16 //number of microsteps - #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E0_IS_L6470 #define E0_MICROSTEPS 16 //number of microsteps - #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E1_IS_L6470 - #define E1_MICROSTEPS 16 //number of microsteps #define E1_MICROSTEPS 16 //number of microsteps - #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E2_IS_L6470 - #define E2_MICROSTEPS 16 //number of microsteps #define E2_MICROSTEPS 16 //number of microsteps - #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + //#define E3_IS_L6470 - #define E3_MICROSTEPS 16 //number of microsteps #define E3_MICROSTEPS 16 //number of microsteps - #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high + #define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high #define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off #define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall - + #endif #include "Conditionals.h" diff --git a/Marlin/fastio.h b/Marlin/fastio.h index 76012d522..5871e2287 100644 --- a/Marlin/fastio.h +++ b/Marlin/fastio.h @@ -30,15 +30,15 @@ #define _WRITE_C(IO, v) do { if (v) { \ CRITICAL_SECTION_START; \ - {DIO ## IO ## _WPORT |= MASK(DIO ## IO ## _PIN); }\ + {DIO ## IO ## _WPORT |= MASK(DIO ## IO ## _PIN); } \ CRITICAL_SECTION_END; \ - }\ - else {\ + } \ + else { \ CRITICAL_SECTION_START; \ - {DIO ## IO ## _WPORT &= ~MASK(DIO ## IO ## _PIN); }\ + {DIO ## IO ## _WPORT &= ~MASK(DIO ## IO ## _PIN); } \ CRITICAL_SECTION_END; \ - }\ - }\ + } \ + } \ while (0) #define _WRITE(IO, v) do { if (&(DIO ## IO ## _RPORT) >= (uint8_t *)0x100) {_WRITE_C(IO, v); } else {_WRITE_NC(IO, v); }; } while (0) diff --git a/Marlin/planner.cpp b/Marlin/planner.cpp index 8e2d10812..b2d91606d 100644 --- a/Marlin/planner.cpp +++ b/Marlin/planner.cpp @@ -439,10 +439,12 @@ void check_axes_activity() { // Just starting up fan - run at full power. fan_kick_end = ms + FAN_KICKSTART_TIME; tail_fan_speed = 255; - } else if (fan_kick_end > ms) + } + else if (fan_kick_end > ms) // Fan still spinning up. tail_fan_speed = 255; - } else { + } + else { fan_kick_end = 0; } #endif //FAN_KICKSTART_TIME diff --git a/Marlin/qr_solve.cpp b/Marlin/qr_solve.cpp index f968590ca..1e085c95b 100644 --- a/Marlin/qr_solve.cpp +++ b/Marlin/qr_solve.cpp @@ -494,7 +494,8 @@ double dnrm2(int n, double x[], int incx) if (scale < absxi) { ssq = 1.0 + ssq * (scale / absxi) * (scale / absxi); scale = absxi; - } else + } + else ssq = ssq + (absxi / scale) * (absxi / scale); } ix += incx; @@ -1023,7 +1024,7 @@ void dqrlss(double a[], int lda, int m, int n, int kr, double b[], double x[], if (kr != 0) { job = 110; - info = dqrsl(a, lda, m, kr, qraux, b, rsd, rsd, x, rsd, rsd, job); + info = dqrsl(a, lda, m, kr, qraux, b, rsd, rsd, x, rsd, rsd, job); UNUSED(info); } for (i = 0; i < n; i++) @@ -1404,7 +1405,8 @@ void dscal(int n, double sa, double x[], int incx) x[i + 3] = sa * x[i + 3]; x[i + 4] = sa * x[i + 4]; } - } else { + } + else { if (0 <= incx) ix = 0; else @@ -1486,15 +1488,10 @@ void dswap(int n, double x[], int incx, double y[], int incy) x[i + 2] = y[i + 2]; y[i + 2] = temp; } - } else { - if (0 <= incx) - ix = 0; - else - ix = (- n + 1) * incx; - if (0 <= incy) - iy = 0; - else - iy = (- n + 1) * incy; + } + else { + ix = (incx >= 0) ? 0 : (-n + 1) * incx; + iy = (incy >= 0) ? 0 : (-n + 1) * incy; for (i = 0; i < n; i++) { temp = x[ix]; x[ix] = y[iy]; @@ -1566,7 +1563,7 @@ void qr_solve(double x[], int m, int n, double a[], double b[]) tol = r8_epsilon() / r8mat_amax(m, n, a_qr); itask = 1; - ind = dqrls(a_qr, lda, m, n, tol, &kr, b, x, r, jpvt, qraux, itask); + ind = dqrls(a_qr, lda, m, n, tol, &kr, b, x, r, jpvt, qraux, itask); UNUSED(ind); } /******************************************************************************/ diff --git a/Marlin/stepper.cpp b/Marlin/stepper.cpp index e5639c5e5..327b6449a 100644 --- a/Marlin/stepper.cpp +++ b/Marlin/stepper.cpp @@ -139,11 +139,13 @@ volatile signed char count_direction[NUM_AXIS] = { 1, 1, 1, 1 }; if (Z_HOME_DIR > 0) {\ if (!(TEST(old_endstop_bits, Z_MAX) && (count_direction[Z_AXIS] > 0)) && !locked_z_motor) Z_STEP_WRITE(v); \ if (!(TEST(old_endstop_bits, Z2_MAX) && (count_direction[Z_AXIS] > 0)) && !locked_z2_motor) Z2_STEP_WRITE(v); \ - } else {\ + } \ + else { \ if (!(TEST(old_endstop_bits, Z_MIN) && (count_direction[Z_AXIS] < 0)) && !locked_z_motor) Z_STEP_WRITE(v); \ if (!(TEST(old_endstop_bits, Z2_MIN) && (count_direction[Z_AXIS] < 0)) && !locked_z2_motor) Z2_STEP_WRITE(v); \ } \ - } else { \ + } \ + else { \ Z_STEP_WRITE(v); \ Z2_STEP_WRITE(v); \ } @@ -397,7 +399,7 @@ inline void update_endstops() { COPY_BIT(current_endstop_bits, Z_MIN, Z2_MIN); #endif - byte z_test = TEST_ENDSTOP(Z_MIN) << 0 + TEST_ENDSTOP(Z2_MIN) << 1; // bit 0 for Z, bit 1 for Z2 + byte z_test = TEST_ENDSTOP(Z_MIN) | (TEST_ENDSTOP(Z2_MIN) << 1); // bit 0 for Z, bit 1 for Z2 if (z_test && current_block->steps[Z_AXIS] > 0) { // z_test = Z_MIN || Z2_MIN endstops_trigsteps[Z_AXIS] = count_position[Z_AXIS]; @@ -433,7 +435,7 @@ inline void update_endstops() { COPY_BIT(current_endstop_bits, Z_MAX, Z2_MAX); #endif - byte z_test = TEST_ENDSTOP(Z_MAX) << 0 + TEST_ENDSTOP(Z2_MAX) << 1; // bit 0 for Z, bit 1 for Z2 + byte z_test = TEST_ENDSTOP(Z_MAX) | (TEST_ENDSTOP(Z2_MAX) << 1); // bit 0 for Z, bit 1 for Z2 if (z_test && current_block->steps[Z_AXIS] > 0) { // t_test = Z_MAX || Z2_MAX endstops_trigsteps[Z_AXIS] = count_position[Z_AXIS]; diff --git a/Marlin/temperature.cpp b/Marlin/temperature.cpp index 40d1a4bfc..3a8c6a8b5 100644 --- a/Marlin/temperature.cpp +++ b/Marlin/temperature.cpp @@ -21,11 +21,13 @@ #include "Marlin.h" #include "ultralcd.h" #include "temperature.h" -#include "watchdog.h" #include "language.h" - #include "Sd2PinMap.h" +#if ENABLED(USE_WATCHDOG) + #include "watchdog.h" +#endif + //=========================================================================== //================================== macros ================================= //=========================================================================== @@ -207,7 +209,7 @@ void PID_autotune(float temp, int extruder, int ncycles) { long bias, d; float Ku, Tu; - float Kp, Ki, Kd; + float Kp = 0, Ki = 0, Kd = 0; float max = 0, min = 10000; #if HAS_AUTO_FAN @@ -511,7 +513,8 @@ float get_pid_output(int e) { if (e_position > last_position[e]) { lpq[lpq_ptr++] = e_position - last_position[e]; last_position[e] = e_position; - } else { + } + else { lpq[lpq_ptr++] = 0; } if (lpq_ptr >= lpq_len) lpq_ptr = 0; @@ -818,8 +821,11 @@ static void updateTemperaturesFromRawValues() { #if HAS_FILAMENT_SENSOR filament_width_meas = analog2widthFil(); #endif - //Reset the watchdog after we know we have a temperature measurement. - watchdog_reset(); + + #if ENABLED(USE_WATCHDOG) + // Reset the watchdog after we know we have a temperature measurement. + watchdog_reset(); + #endif CRITICAL_SECTION_START; temp_meas_ready = false; diff --git a/Marlin/ultralcd.cpp b/Marlin/ultralcd.cpp index 54c1bfc9b..1a0ee8a4a 100644 --- a/Marlin/ultralcd.cpp +++ b/Marlin/ultralcd.cpp @@ -475,53 +475,51 @@ void lcd_set_home_offsets() { #endif //BABYSTEPPING /** - * - * "Tune" submenu - * + * Watch temperature callbacks */ +#if TEMP_SENSOR_0 != 0 + void watch_temp_callback_E0() { start_watching_heater(0); } +#endif +#if EXTRUDERS > 1 && TEMP_SENSOR_1 != 0 + void watch_temp_callback_E1() { start_watching_heater(1); } + #if EXTRUDERS > 2 && TEMP_SENSOR_2 != 0 + void watch_temp_callback_E2() { start_watching_heater(2); } + #if EXTRUDERS > 3 && TEMP_SENSOR_3 != 0 + void watch_temp_callback_E3() { start_watching_heater(3); } + #endif // EXTRUDERS > 3 + #endif // EXTRUDERS > 2 +#endif // EXTRUDERS > 1 -static void lcd_tune_menu() { - START_MENU(); - - // - // ^ Main - // - MENU_ITEM(back, MSG_MAIN, lcd_main_menu); - - // - // Speed: - // - MENU_ITEM_EDIT(int3, MSG_SPEED, &feedrate_multiplier, 10, 999); - +/** + * Items shared between Tune and Temperature menus + */ +static void nozzle_bed_fan_menu_items(uint8_t &encoderLine, uint8_t &_lineNr, uint8_t &_drawLineNr, uint8_t &_menuItemNr, bool &wasClicked, bool &itemSelected) { // // Nozzle: - // Nozzle 1: - // Nozzle 2: - // Nozzle 3: - // Nozzle 4: + // Nozzle [1-4]: // #if EXTRUDERS == 1 #if TEMP_SENSOR_0 != 0 - MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_NOZZLE, &target_temperature[0], 0, HEATER_0_MAXTEMP - 15); + MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE, &target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0); #endif #else //EXTRUDERS > 1 #if TEMP_SENSOR_0 != 0 - MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_NOZZLE MSG_N1, &target_temperature[0], 0, HEATER_0_MAXTEMP - 15); + MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N1, &target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0); #endif #if TEMP_SENSOR_1 != 0 - MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_NOZZLE MSG_N2, &target_temperature[1], 0, HEATER_1_MAXTEMP - 15); + MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N2, &target_temperature[1], 0, HEATER_1_MAXTEMP - 15, watch_temp_callback_E1); #endif #if EXTRUDERS > 2 #if TEMP_SENSOR_2 != 0 - MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_NOZZLE MSG_N3, &target_temperature[2], 0, HEATER_2_MAXTEMP - 15); + MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N3, &target_temperature[2], 0, HEATER_2_MAXTEMP - 15, watch_temp_callback_E2); #endif #if EXTRUDERS > 3 #if TEMP_SENSOR_3 != 0 - MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_NOZZLE MSG_N4, &target_temperature[3], 0, HEATER_3_MAXTEMP - 15); + MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N4, &target_temperature[3], 0, HEATER_3_MAXTEMP - 15, watch_temp_callback_E3); #endif - #endif //EXTRUDERS > 3 - #endif //EXTRUDERS > 2 - #endif //EXTRUDERS > 1 + #endif // EXTRUDERS > 3 + #endif // EXTRUDERS > 2 + #endif // EXTRUDERS > 1 // // Bed: @@ -534,11 +532,29 @@ static void lcd_tune_menu() { // Fan Speed: // MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_FAN_SPEED, &fanSpeed, 0, 255); +} + + +/** + * + * "Tune" submenu + * + */ +static void lcd_tune_menu() { + START_MENU(); // - // Flow: + // ^ Main + // + MENU_ITEM(back, MSG_MAIN, lcd_main_menu); + + // + // Speed: // - MENU_ITEM_EDIT(int3, MSG_FLOW, &extruder_multiplier[active_extruder], 10, 999); + MENU_ITEM_EDIT(int3, MSG_SPEED, &feedrate_multiplier, 10, 999); + + // Nozzle, Bed, and Fan Control + nozzle_bed_fan_menu_items(encoderLine, _lineNr, _drawLineNr, _menuItemNr, wasClicked, itemSelected); // // Flow: @@ -550,6 +566,7 @@ static void lcd_tune_menu() { #if EXTRUDERS == 1 MENU_ITEM_EDIT(int3, MSG_FLOW, &extruder_multiplier[0], 10, 999); #else // EXTRUDERS > 1 + MENU_ITEM_EDIT(int3, MSG_FLOW, &extruder_multiplier[active_extruder], 10, 999); MENU_ITEM_EDIT(int3, MSG_FLOW MSG_N1, &extruder_multiplier[0], 10, 999); MENU_ITEM_EDIT(int3, MSG_FLOW MSG_N2, &extruder_multiplier[1], 10, 999); #if EXTRUDERS > 2 @@ -1002,44 +1019,8 @@ static void lcd_control_temperature_menu() { // MENU_ITEM(back, MSG_CONTROL, lcd_control_menu); - // - // Nozzle - // Nozzle 1, Nozzle 2, Nozzle 3, Nozzle 4 - // - #if EXTRUDERS == 1 - #if TEMP_SENSOR_0 != 0 - MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_NOZZLE, &target_temperature[0], 0, HEATER_0_MAXTEMP - 15); - #endif - #else //EXTRUDERS > 1 - #if TEMP_SENSOR_0 != 0 - MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_NOZZLE MSG_N1, &target_temperature[0], 0, HEATER_0_MAXTEMP - 15); - #endif - #if TEMP_SENSOR_1 != 0 - MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_NOZZLE MSG_N2, &target_temperature[1], 0, HEATER_1_MAXTEMP - 15); - #endif - #if EXTRUDERS > 2 - #if TEMP_SENSOR_2 != 0 - MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_NOZZLE MSG_N3, &target_temperature[2], 0, HEATER_2_MAXTEMP - 15); - #endif - #if EXTRUDERS > 3 - #if TEMP_SENSOR_3 != 0 - MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_NOZZLE MSG_N4, &target_temperature[3], 0, HEATER_3_MAXTEMP - 15); - #endif - #endif // EXTRUDERS > 3 - #endif // EXTRUDERS > 2 - #endif // EXTRUDERS > 1 - - // - // Bed - // - #if TEMP_SENSOR_BED != 0 - MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_BED, &target_temperature_bed, 0, BED_MAXTEMP - 15); - #endif - - // - // Fan Speed - // - MENU_MULTIPLIER_ITEM_EDIT(int3, MSG_FAN_SPEED, &fanSpeed, 0, 255); + // Nozzle, Bed, and Fan Control + nozzle_bed_fan_menu_items(encoderLine, _lineNr, _drawLineNr, _menuItemNr, wasClicked, itemSelected); // // Autotemp, Min, Max, Fact diff --git a/Marlin/ultralcd_implementation_hitachi_HD44780.h b/Marlin/ultralcd_implementation_hitachi_HD44780.h index 6c2828c70..ccb09b425 100644 --- a/Marlin/ultralcd_implementation_hitachi_HD44780.h +++ b/Marlin/ultralcd_implementation_hitachi_HD44780.h @@ -716,8 +716,8 @@ static void lcd_implementation_status_screen() { lcd.print(ftostr12ns(filament_width_meas)); lcd_printPGM(PSTR(" V")); lcd.print(itostr3(100.0 * volumetric_multiplier[FILAMENT_SENSOR_EXTRUDER_NUM])); - lcd.print('%'); - return; + lcd.print('%'); + return; } #endif // FILAMENT_LCD_DISPLAY diff --git a/Marlin/utf_mapper.h b/Marlin/utf_mapper.h index 76425364b..6367be66e 100644 --- a/Marlin/utf_mapper.h +++ b/Marlin/utf_mapper.h @@ -123,14 +123,17 @@ #endif // SIMULATE_ROMFONT #if ENABLED(MAPPER_NON) - char charset_mapper(char c){ + + char charset_mapper(char c) { HARDWARE_CHAR_OUT( c ); return 1; } + #elif ENABLED(MAPPER_C2C3) - uint8_t utf_hi_char; // UTF-8 high part - bool seen_c2 = false; - char charset_mapper(char c){ + + char charset_mapper(char c) { + static uint8_t utf_hi_char; // UTF-8 high part + static bool seen_c2 = false; uint8_t d = c; if ( d >= 0x80 ) { // UTF-8 handling if ( (d >= 0xc0) && (!seen_c2) ) { @@ -138,16 +141,16 @@ seen_c2 = true; return 0; } - else if (seen_c2){ + else if (seen_c2) { d &= 0x3f; #ifndef MAPPER_ONE_TO_ONE - HARDWARE_CHAR_OUT( (char) pgm_read_byte_near( utf_recode + d + ( utf_hi_char << 6 ) - 0x20 ) ); + HARDWARE_CHAR_OUT((char)pgm_read_byte_near(utf_recode + d + (utf_hi_char << 6) - 0x20)); #else - HARDWARE_CHAR_OUT( (char) (0x80 + ( utf_hi_char << 6 ) + d) ) ; + HARDWARE_CHAR_OUT((char)(0x80 + (utf_hi_char << 6) + d)) ; #endif } else { - HARDWARE_CHAR_OUT('?'); + HARDWARE_CHAR_OUT('?'); } } else { @@ -156,96 +159,116 @@ seen_c2 = false; return 1; } + #elif ENABLED(MAPPER_D0D1_MOD) - uint8_t utf_hi_char; // UTF-8 high part - bool seen_d5 = false; - char charset_mapper(char c){ + + char charset_mapper(char c) { // it is a Russian alphabet translation // except 0401 --> 0xa2 = Ё, 0451 --> 0xb5 = ё + static uint8_t utf_hi_char; // UTF-8 high part + static bool seen_d5 = false; uint8_t d = c; - if ( d >= 0x80 ) { // UTF-8 handling - if ((d >= 0xd0) && (!seen_d5)) { + if (d >= 0x80) { // UTF-8 handling + if (d >= 0xd0 && !seen_d5) { utf_hi_char = d - 0xd0; seen_d5 = true; return 0; - } else if (seen_d5) { - d &= 0x3f; - if ( !utf_hi_char && ( d == 1 )) { - HARDWARE_CHAR_OUT((char) 0xa2 ); // Ё - } else if ((utf_hi_char == 1) && (d == 0x11)) { - HARDWARE_CHAR_OUT((char) 0xb5 ); // ё - } else { - HARDWARE_CHAR_OUT((char) pgm_read_byte_near( utf_recode + d + ( utf_hi_char << 6 ) - 0x10 ) ); - } + } + else if (seen_d5) { + d &= 0x3f; + if (!utf_hi_char && d == 1) { + HARDWARE_CHAR_OUT((char) 0xa2); // Ё + } + else if (utf_hi_char == 1 && d == 0x11) { + HARDWARE_CHAR_OUT((char)0xb5); // ё } else { - HARDWARE_CHAR_OUT('?'); + HARDWARE_CHAR_OUT((char)pgm_read_byte_near(utf_recode + d + (utf_hi_char << 6) - 0x10)); } - } else { + } + else { + HARDWARE_CHAR_OUT('?'); + } + } + else { HARDWARE_CHAR_OUT((char) c ); } seen_d5 = false; return 1; } + #elif ENABLED(MAPPER_D0D1) - uint8_t utf_hi_char; // UTF-8 high part - bool seen_d5 = false; + char charset_mapper(char c) { + static uint8_t utf_hi_char; // UTF-8 high part + static bool seen_d5 = false; uint8_t d = c; - if ( d >= 0x80u ) { // UTF-8 handling - if ((d >= 0xd0u) && (!seen_d5)) { + if (d >= 0x80u) { // UTF-8 handling + if (d >= 0xd0u && !seen_d5) { utf_hi_char = d - 0xd0u; seen_d5 = true; return 0; - } else if (seen_d5) { - d &= 0x3fu; + } + else if (seen_d5) { + d &= 0x3fu; #ifndef MAPPER_ONE_TO_ONE - HARDWARE_CHAR_OUT( (char) pgm_read_byte_near( utf_recode + d + ( utf_hi_char << 6 ) - 0x20 ) ); + HARDWARE_CHAR_OUT((char)pgm_read_byte_near(utf_recode + d + (utf_hi_char << 6) - 0x20)); #else - HARDWARE_CHAR_OUT( (char) (0xa0u + ( utf_hi_char << 6 ) + d ) ) ; + HARDWARE_CHAR_OUT((char)(0xa0u + (utf_hi_char << 6) + d)) ; #endif - } else { + } + else { HARDWARE_CHAR_OUT('?'); } - } else { + } + else { HARDWARE_CHAR_OUT((char) c ); } seen_d5 = false; return 1; } + #elif ENABLED(MAPPER_E382E383) - uint8_t utf_hi_char; // UTF-8 high part - bool seen_e3 = false; - bool seen_82_83 = false; - char charset_mapper(char c){ + + char charset_mapper(char c) { + static uint8_t utf_hi_char; // UTF-8 high part + static bool seen_e3 = false; + static bool seen_82_83 = false; uint8_t d = c; - if ( d >= 0x80 ) { // UTF-8 handling - if ( (d == 0xe3) && (seen_e3 == false)) { + if (d >= 0x80) { // UTF-8 handling + if (d == 0xe3 && !seen_e3) { seen_e3 = true; return 0; // eat 0xe3 - } else if ( (d >= 0x82) && (seen_e3 == true) && (seen_82_83 == false)) { + } + else if (d >= 0x82 && seen_e3 && !seen_82_83) { utf_hi_char = d - 0x82; seen_82_83 = true; return 0; - } else if ((seen_e3 == true) && (seen_82_83 == true)){ + } + else if (seen_e3 && seen_82_83) { d &= 0x3f; #ifndef MAPPER_ONE_TO_ONE - HARDWARE_CHAR_OUT( (char) pgm_read_byte_near( utf_recode + d + ( utf_hi_char << 6 ) - 0x20 ) ); + HARDWARE_CHAR_OUT((char)pgm_read_byte_near(utf_recode + d + (utf_hi_char << 6) - 0x20)); #else - HARDWARE_CHAR_OUT( (char) (0x80 + ( utf_hi_char << 6 ) + d ) ) ; + HARDWARE_CHAR_OUT((char)(0x80 + (utf_hi_char << 6) + d)) ; #endif - } else { + } + else { HARDWARE_CHAR_OUT((char) '?' ); } - } else { + } + else { HARDWARE_CHAR_OUT((char) c ); } seen_e3 = false; seen_82_83 = false; return 1; } + #else + #error "You have to define one of the DISPLAY_INPUT_CODE_MAPPERs in your language_xx.h file" // should not occur because (en) will set. + #endif // code mappers #endif // UTF_MAPPER_H diff --git a/Marlin/watchdog.cpp b/Marlin/watchdog.cpp index c30cb54c5..e76327971 100644 --- a/Marlin/watchdog.cpp +++ b/Marlin/watchdog.cpp @@ -1,25 +1,14 @@ #include "Marlin.h" #if ENABLED(USE_WATCHDOG) -#include #include "watchdog.h" -#include "ultralcd.h" -//=========================================================================== -//============================ private variables ============================ -//=========================================================================== - -//=========================================================================== -//================================ functions ================================ -//=========================================================================== - - -/// intialise watch dog with a 4 sec interrupt time +// Initialize watchdog with a 4 sec interrupt time void watchdog_init() { #if ENABLED(WATCHDOG_RESET_MANUAL) - //We enable the watchdog timer, but only for the interrupt. - //Take care, as this requires the correct order of operation, with interrupts disabled. See the datasheet of any AVR chip for details. + // We enable the watchdog timer, but only for the interrupt. + // Take care, as this requires the correct order of operation, with interrupts disabled. See the datasheet of any AVR chip for details. wdt_reset(); _WD_CONTROL_REG = _BV(_WD_CHANGE_BIT) | _BV(WDE); _WD_CONTROL_REG = _BV(WDIE) | WDTO_4S; @@ -28,23 +17,18 @@ void watchdog_init() { #endif } -/// reset watchdog. MUST be called every 1s after init or avr will reset. -void watchdog_reset() { - wdt_reset(); -} - //=========================================================================== //=================================== ISR =================================== //=========================================================================== -//Watchdog timer interrupt, called if main program blocks >1sec and manual reset is enabled. +// Watchdog timer interrupt, called if main program blocks >1sec and manual reset is enabled. #if ENABLED(WATCHDOG_RESET_MANUAL) -ISR(WDT_vect) { - SERIAL_ERROR_START; - SERIAL_ERRORLNPGM("Something is wrong, please turn off the printer."); - kill(PSTR("ERR:Please Reset")); //kill blocks //16 characters so it fits on a 16x2 display - while (1); //wait for user or serial reset -} -#endif//RESET_MANUAL - -#endif//USE_WATCHDOG + ISR(WDT_vect) { + SERIAL_ERROR_START; + SERIAL_ERRORLNPGM("Something is wrong, please turn off the printer."); + kill(PSTR("ERR:Please Reset")); //kill blocks //16 characters so it fits on a 16x2 display + while (1); //wait for user or serial reset + } +#endif //WATCHDOG_RESET_MANUAL + +#endif //USE_WATCHDOG diff --git a/Marlin/watchdog.h b/Marlin/watchdog.h index 6416f13de..c8a671fe8 100644 --- a/Marlin/watchdog.h +++ b/Marlin/watchdog.h @@ -2,16 +2,13 @@ #define WATCHDOG_H #include "Marlin.h" +#include -#if ENABLED(USE_WATCHDOG) - // initialize watch dog with a 1 sec interrupt time - void watchdog_init(); - // pad the dog/reset watchdog. MUST be called at least every second after the first watchdog_init or AVR will go into emergency procedures.. - void watchdog_reset(); -#else - //If we do not have a watchdog, then we can have empty functions which are optimized away. - FORCE_INLINE void watchdog_init() {}; - FORCE_INLINE void watchdog_reset() {}; -#endif +// Initialize watchdog with a 4 second interrupt time +void watchdog_init(); + +// Reset watchdog. MUST be called at least every 4 seconds after the +// first watchdog_init or AVR will go into emergency procedures. +inline void watchdog_reset() { wdt_reset(); } #endif