diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 122d4cec4..8835a2e48 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 74f336aed..ee66d1338 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -744,7 +744,7 @@
 #define MAX_CMD_SIZE 96
 #define BUFSIZE 4
 
-// Transfer Buffer Size
+// Transmission to Host Buffer Size
 // To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
 // To buffer a simple "ok" you need 4 bytes.
 // For ADVANCED_OK (M105) you need 32 bytes.
@@ -753,6 +753,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/MarlinSerial.cpp b/Marlin/MarlinSerial.cpp
index 235e01809..778125818 100644
--- a/Marlin/MarlinSerial.cpp
+++ b/Marlin/MarlinSerial.cpp
@@ -27,15 +27,30 @@
  * Modified 23 November 2006 by David A. Mellis
  * Modified 28 September 2010 by Mark Sproul
  * Modified 14 February 2016 by Andreas Hardtung (added tx buffer)
+ * Modified 01 October 2017 by Eduardo José Tagle (added XON/XOFF)
  */
 
-#include "MarlinSerial.h"
-#include "Marlin.h"
-
 // Disable HardwareSerial.cpp to support chips without a UART (Attiny, etc.)
 
+#include "MarlinConfig.h"
+
 #if !defined(USBCON) && (defined(UBRRH) || defined(UBRR0H) || defined(UBRR1H) || defined(UBRR2H) || defined(UBRR3H))
 
+  #include "MarlinSerial.h"
+  #include "Marlin.h"
+
+  struct ring_buffer_r {
+    unsigned char buffer[RX_BUFFER_SIZE];
+    volatile ring_buffer_pos_t head, tail;
+  };
+
+  #if TX_BUFFER_SIZE > 0
+    struct ring_buffer_t {
+      unsigned char buffer[TX_BUFFER_SIZE];
+      volatile uint8_t head, tail;
+    };
+  #endif
+
   #if UART_PRESENT(SERIAL_PORT)
     ring_buffer_r rx_buffer = { { 0 }, 0, 0 };
     #if TX_BUFFER_SIZE > 0
@@ -44,6 +59,23 @@
     #endif
   #endif
 
+  #if ENABLED(SERIAL_XON_XOFF)
+    uint8_t xon_xoff_state = XON_XOFF_CHAR_SENT | XON_CHAR;
+    constexpr uint8_t XON_XOFF_CHAR_SENT = 0x80;  // XON / XOFF Character was sent
+    constexpr uint8_t XON_XOFF_CHAR_MASK = 0x1F;  // XON / XOFF character to send
+    // XON / XOFF character definitions
+    constexpr uint8_t XON_CHAR  = 17;
+    constexpr uint8_t XOFF_CHAR = 19;
+  #endif
+
+  #if ENABLED(SERIAL_STATS_DROPPED_RX)
+    uint8_t rx_dropped_bytes = 0;
+  #endif
+
+  #if ENABLED(SERIAL_STATS_MAX_RX_QUEUED)
+    ring_buffer_pos_t rx_max_enqueued = 0;
+  #endif
+
   #if ENABLED(EMERGENCY_PARSER)
 
     #include "stepper.h"
@@ -136,20 +168,78 @@
 
   #endif // EMERGENCY_PARSER
 
-  FORCE_INLINE void store_char(unsigned char c) {
-    CRITICAL_SECTION_START;
-      const uint8_t h = rx_buffer.head,
-                    i = (uint8_t)(h + 1) & (RX_BUFFER_SIZE - 1);
-
-      // if we should be storing the received character into the location
-      // just before the tail (meaning that the head would advance to the
-      // current location of the tail), we're about to overflow the buffer
-      // and so we don't write the character or advance the head.
-      if (i != rx_buffer.tail) {
-        rx_buffer.buffer[h] = c;
-        rx_buffer.head = i;
+  FORCE_INLINE void store_rxd_char() {
+    const ring_buffer_pos_t h = rx_buffer.head,
+                            i = (ring_buffer_pos_t)(h + 1) & (ring_buffer_pos_t)(RX_BUFFER_SIZE - 1);
+
+    // If the character is to be stored at the index just before the tail
+    // (such that the head would advance to the current tail), the buffer is
+    // critical, so don't write the character or advance the head.
+    if (i != rx_buffer.tail) {
+      rx_buffer.buffer[h] = M_UDRx;
+      rx_buffer.head = i;
+    }
+    else {
+      (void)M_UDRx;
+      #if ENABLED(SERIAL_STATS_DROPPED_RX)
+        if (!++rx_dropped_bytes) ++rx_dropped_bytes;
+      #endif
+    }
+
+    #if ENABLED(SERIAL_STATS_MAX_RX_QUEUED)
+      // calculate count of bytes stored into the RX buffer
+      ring_buffer_pos_t rx_count = (ring_buffer_pos_t)(rx_buffer.head - rx_buffer.tail) & (ring_buffer_pos_t)(RX_BUFFER_SIZE - 1);
+      // Keep track of the maximum count of enqueued bytes
+      NOLESS(rx_max_enqueued, rx_count);
+    #endif
+
+    #if ENABLED(SERIAL_XON_XOFF)
+
+      // for high speed transfers, we can use XON/XOFF protocol to do
+      // software handshake and avoid overruns.
+      if ((xon_xoff_state & XON_XOFF_CHAR_MASK) == XON_CHAR) {
+
+        // calculate count of bytes stored into the RX buffer
+        ring_buffer_pos_t rx_count = (ring_buffer_pos_t)(rx_buffer.head - rx_buffer.tail) & (ring_buffer_pos_t)(RX_BUFFER_SIZE - 1);
+
+        // if we are above 12.5% of RX buffer capacity, send XOFF before
+        // we run out of RX buffer space .. We need 325 bytes @ 250kbits/s to
+        // let the host react and stop sending bytes. This translates to 13mS
+        // propagation time.
+        if (rx_count >= (RX_BUFFER_SIZE) / 8) {
+          // If TX interrupts are disabled and data register is empty,
+          // just write the byte to the data register and be done. This
+          // shortcut helps significantly improve the effective datarate
+          // at high (>500kbit/s) bitrates, where interrupt overhead
+          // becomes a slowdown.
+          if (!TEST(M_UCSRxB, M_UDRIEx) && TEST(M_UCSRxA, M_UDREx)) {
+            // Send an XOFF character
+            M_UDRx = XOFF_CHAR;
+            // clear the TXC bit -- "can be cleared by writing a one to its bit
+            // location". This makes sure flush() won't return until the bytes
+            // actually got written
+            SBI(M_UCSRxA, M_TXCx);
+            // And remember it was sent
+            xon_xoff_state = XOFF_CHAR | XON_XOFF_CHAR_SENT;
+          }
+          else {
+            // TX interrupts disabled, but buffer still not empty ... or
+            // TX interrupts enabled. Reenable TX ints and schedule XOFF
+            // character to be sent
+            #if TX_BUFFER_SIZE > 0
+              SBI(M_UCSRxB, M_UDRIEx);
+              xon_xoff_state = XOFF_CHAR;
+            #else
+              // We are not using TX interrupts, we will have to send this manually
+              while (!TEST(M_UCSRxA, M_UDREx)) {/* nada */}
+              M_UDRx = XOFF_CHAR;
+              // And remember we already sent it
+              xon_xoff_state = XOFF_CHAR | XON_XOFF_CHAR_SENT;
+            #endif
+          }
+        }
       }
-    CRITICAL_SECTION_END;
+    #endif // SERIAL_XON_XOFF
 
     #if ENABLED(EMERGENCY_PARSER)
       emergency_parser(c);
@@ -160,37 +250,41 @@
 
     FORCE_INLINE void _tx_udr_empty_irq(void) {
       // If interrupts are enabled, there must be more data in the output
-      // buffer. Send the next byte
-      const uint8_t t = tx_buffer.tail,
-                    c = tx_buffer.buffer[t];
-      tx_buffer.tail = (t + 1) & (TX_BUFFER_SIZE - 1);
-
-      M_UDRx = c;
+      // buffer.
+
+      #if ENABLED(SERIAL_XON_XOFF)
+        // Do a priority insertion of an XON/XOFF char, if needed.
+        const uint8_t state = xon_xoff_state;
+        if (!(state & XON_XOFF_CHAR_SENT)) {
+          M_UDRx = state & XON_XOFF_CHAR_MASK;
+          xon_xoff_state = state | XON_XOFF_CHAR_SENT;
+        }
+        else
+      #endif
+      { // Send the next byte
+        const uint8_t t = tx_buffer.tail, c = tx_buffer.buffer[t];
+        tx_buffer.tail = (t + 1) & (TX_BUFFER_SIZE - 1);
+        M_UDRx = c;
+      }
 
       // clear the TXC bit -- "can be cleared by writing a one to its bit
       // location". This makes sure flush() won't return until the bytes
       // actually got written
       SBI(M_UCSRxA, M_TXCx);
 
-      if (tx_buffer.head == tx_buffer.tail) {
-        // Buffer empty, so disable interrupts
+      // Disable interrupts if the buffer is empty
+      if (tx_buffer.head == tx_buffer.tail)
         CBI(M_UCSRxB, M_UDRIEx);
-      }
     }
 
     #ifdef M_USARTx_UDRE_vect
-      ISR(M_USARTx_UDRE_vect) {
-        _tx_udr_empty_irq();
-      }
+      ISR(M_USARTx_UDRE_vect) { _tx_udr_empty_irq(); }
     #endif
 
   #endif // TX_BUFFER_SIZE
 
   #ifdef M_USARTx_RX_vect
-    ISR(M_USARTx_RX_vect) {
-      const unsigned char c = M_UDRx;
-      store_char(c);
-    }
+    ISR(M_USARTx_RX_vect) { store_rxd_char(); }
   #endif
 
   // Public Methods
@@ -200,9 +294,9 @@
     bool useU2X = true;
 
     #if F_CPU == 16000000UL && SERIAL_PORT == 0
-      // hard-coded exception for compatibility with the bootloader shipped
-      // with the Duemilanove and previous boards and the firmware on the 8U2
-      // on the Uno and Mega 2560.
+      // Hard-coded exception for compatibility with the bootloader shipped
+      // with the Duemilanove and previous boards, and the firmware on the
+      // 8U2 on the Uno and Mega 2560.
       if (baud == 57600) useU2X = false;
     #endif
 
@@ -237,8 +331,9 @@
 
   void MarlinSerial::checkRx(void) {
     if (TEST(M_UCSRxA, M_RXCx)) {
-      const uint8_t c = M_UDRx;
-      store_char(c);
+      CRITICAL_SECTION_START;
+        store_rxd_char();
+      CRITICAL_SECTION_END;
     }
   }
 
@@ -252,51 +347,81 @@
   int MarlinSerial::read(void) {
     int v;
     CRITICAL_SECTION_START;
-      const uint8_t t = rx_buffer.tail;
+      const ring_buffer_pos_t t = rx_buffer.tail;
       if (rx_buffer.head == t)
         v = -1;
       else {
         v = rx_buffer.buffer[t];
-        rx_buffer.tail = (uint8_t)(t + 1) & (RX_BUFFER_SIZE - 1);
+        rx_buffer.tail = (ring_buffer_pos_t)(t + 1) & (RX_BUFFER_SIZE - 1);
+
+        #if ENABLED(SERIAL_XON_XOFF)
+          if ((xon_xoff_state & XON_XOFF_CHAR_MASK) == XOFF_CHAR) {
+            // Get count of bytes in the RX buffer
+            ring_buffer_pos_t rx_count = (ring_buffer_pos_t)(rx_buffer.head - rx_buffer.tail) & (ring_buffer_pos_t)(RX_BUFFER_SIZE - 1);
+            // When below 10% of RX buffer capacity, send XON before
+            // running out of RX buffer bytes
+            if (rx_count < (RX_BUFFER_SIZE) / 10) {
+              xon_xoff_state = XON_CHAR | XON_XOFF_CHAR_SENT;
+              CRITICAL_SECTION_END;       // End critical section before returning!
+              writeNoHandshake(XON_CHAR);
+              return v;
+            }
+          }
+        #endif
       }
     CRITICAL_SECTION_END;
     return v;
   }
 
-  uint8_t MarlinSerial::available(void) {
+  ring_buffer_pos_t MarlinSerial::available(void) {
     CRITICAL_SECTION_START;
-      const uint8_t h = rx_buffer.head,
-                    t = rx_buffer.tail;
+      const ring_buffer_pos_t h = rx_buffer.head, t = rx_buffer.tail;
     CRITICAL_SECTION_END;
-    return (uint8_t)(RX_BUFFER_SIZE + h - t) & (RX_BUFFER_SIZE - 1);
+    return (ring_buffer_pos_t)(RX_BUFFER_SIZE + h - t) & (RX_BUFFER_SIZE - 1);
   }
 
   void MarlinSerial::flush(void) {
-    // RX
-    // don't reverse this or there may be problems if the RX interrupt
-    // occurs after reading the value of rx_buffer_head but before writing
-    // the value to rx_buffer_tail; the previous value of rx_buffer_head
-    // may be written to rx_buffer_tail, making it appear as if the buffer
-    // were full, not empty.
+    // Don't change this order of operations. If the RX interrupt occurs between
+    // reading rx_buffer_head and updating rx_buffer_tail, the previous rx_buffer_head
+    // may be written to rx_buffer_tail, making the buffer appear full rather than empty.
     CRITICAL_SECTION_START;
       rx_buffer.head = rx_buffer.tail;
     CRITICAL_SECTION_END;
+
+    #if ENABLED(SERIAL_XON_XOFF)
+      if ((xon_xoff_state & XON_XOFF_CHAR_MASK) == XOFF_CHAR) {
+        xon_xoff_state = XON_CHAR | XON_XOFF_CHAR_SENT;
+        writeNoHandshake(XON_CHAR);
+      }
+    #endif
   }
 
   #if TX_BUFFER_SIZE > 0
     uint8_t MarlinSerial::availableForWrite(void) {
       CRITICAL_SECTION_START;
-        const uint8_t h = tx_buffer.head,
-                      t = tx_buffer.tail;
+        const uint8_t h = tx_buffer.head, t = tx_buffer.tail;
       CRITICAL_SECTION_END;
       return (uint8_t)(TX_BUFFER_SIZE + h - t) & (TX_BUFFER_SIZE - 1);
     }
 
     void MarlinSerial::write(const uint8_t c) {
+      #if ENABLED(SERIAL_XON_XOFF)
+        const uint8_t state = xon_xoff_state;
+        if (!(state & XON_XOFF_CHAR_SENT)) {
+          // Send 2 chars: XON/XOFF, then a user-specified char
+          writeNoHandshake(state & XON_XOFF_CHAR_MASK);
+          xon_xoff_state = state | XON_XOFF_CHAR_SENT;
+        }
+      #endif
+      writeNoHandshake(c);
+    }
+
+    void MarlinSerial::writeNoHandshake(const uint8_t c) {
       _written = true;
       CRITICAL_SECTION_START;
         bool emty = (tx_buffer.head == tx_buffer.tail);
       CRITICAL_SECTION_END;
+
       // If the buffer and the data register is empty, just write the byte
       // to the data register and be done. This shortcut helps
       // significantly improve the effective datarate at high (>
@@ -353,20 +478,32 @@
       }
       // If we get here, nothing is queued anymore (DRIE is disabled) and
       // the hardware finished tranmission (TXC is set).
-  }
+    }
 
-  #else
-    void MarlinSerial::write(uint8_t c) {
-      while (!TEST(M_UCSRxA, M_UDREx))
-        ;
-      M_UDRx = c;
+  #else // TX_BUFFER_SIZE == 0
+
+    void MarlinSerial::write(const uint8_t c) {
+      #if ENABLED(SERIAL_XON_XOFF)
+        // Do a priority insertion of an XON/XOFF char, if needed.
+        const uint8_t state = xon_xoff_state;
+        if (!(state & XON_XOFF_CHAR_SENT)) {
+          writeNoHandshake(state & XON_XOFF_CHAR_MASK);
+          xon_xoff_state = state | XON_XOFF_CHAR_SENT;
+        }
+      #endif
+      writeNoHandshake(c);
     }
-  #endif
 
-  // end NEW
+    void MarlinSerial::writeNoHandshake(uint8_t c) {
+      while (!TEST(M_UCSRxA, M_UDREx)) {/* nada */}
+      M_UDRx = c;
+    }
 
-  /// imports from print.h
+  #endif // TX_BUFFER_SIZE == 0
 
+  /**
+   * Imports from print.h
+   */
 
   void MarlinSerial::print(char c, int base) {
     print((long)c, base);
diff --git a/Marlin/MarlinSerial.h b/Marlin/MarlinSerial.h
index 8456a7237..a6c4728ce 100644
--- a/Marlin/MarlinSerial.h
+++ b/Marlin/MarlinSerial.h
@@ -87,34 +87,31 @@
   #ifndef TX_BUFFER_SIZE
     #define TX_BUFFER_SIZE 32
   #endif
-  #if !((RX_BUFFER_SIZE == 256) ||(RX_BUFFER_SIZE == 128) ||(RX_BUFFER_SIZE == 64) ||(RX_BUFFER_SIZE == 32) ||(RX_BUFFER_SIZE == 16) ||(RX_BUFFER_SIZE == 8) ||(RX_BUFFER_SIZE == 4) ||(RX_BUFFER_SIZE == 2))
-    #error "RX_BUFFER_SIZE has to be a power of 2 and >= 2"
+
+  #if ENABLED(SERIAL_XON_XOFF) && RX_BUFFER_SIZE < 1024
+    #error "XON/XOFF requires RX_BUFFER_SIZE >= 1024 for reliable transfers without drops."
   #endif
-  #if !((TX_BUFFER_SIZE == 256) ||(TX_BUFFER_SIZE == 128) ||(TX_BUFFER_SIZE == 64) ||(TX_BUFFER_SIZE == 32) ||(TX_BUFFER_SIZE == 16) ||(TX_BUFFER_SIZE == 8) ||(TX_BUFFER_SIZE == 4) ||(TX_BUFFER_SIZE == 2) ||(TX_BUFFER_SIZE == 0))
-    #error TX_BUFFER_SIZE has to be a power of 2 or 0
+  #if !IS_POWER_OF_2(RX_BUFFER_SIZE) || RX_BUFFER_SIZE < 2
+    #error "RX_BUFFER_SIZE must be a power of 2 greater than 1."
   #endif
-
-  struct ring_buffer_r {
-    unsigned char buffer[RX_BUFFER_SIZE];
-    volatile uint8_t head;
-    volatile uint8_t tail;
-  };
-
-  #if TX_BUFFER_SIZE > 0
-    struct ring_buffer_t {
-      unsigned char buffer[TX_BUFFER_SIZE];
-      volatile uint8_t head;
-      volatile uint8_t tail;
-    };
+  #if TX_BUFFER_SIZE && (TX_BUFFER_SIZE < 2 || TX_BUFFER_SIZE > 256 || !IS_POWER_OF_2(TX_BUFFER_SIZE))
+    #error "TX_BUFFER_SIZE must be 0 or a power of 2 greater than 1."
   #endif
 
-  #if UART_PRESENT(SERIAL_PORT)
-    extern ring_buffer_r rx_buffer;
-    #if TX_BUFFER_SIZE > 0
-      extern ring_buffer_t tx_buffer;
-    #endif
+  #if RX_BUFFER_SIZE > 256
+    typedef uint16_t ring_buffer_pos_t;
+  #else
+    typedef uint8_t ring_buffer_pos_t;
+  #endif
+  
+  #if ENABLED(SERIAL_STATS_DROPPED_RX)
+    extern uint8_t rx_dropped_bytes;
   #endif
 
+  #if ENABLED(SERIAL_STATS_MAX_RX_QUEUED)
+    extern ring_buffer_pos_t rx_max_enqueued;
+  #endif  
+  
   class MarlinSerial { //: public Stream
 
     public:
@@ -124,13 +121,22 @@
       static int peek(void);
       static int read(void);
       static void flush(void);
-      static uint8_t available(void);
+      static ring_buffer_pos_t available(void);
       static void checkRx(void);
       static void write(const uint8_t c);
       #if TX_BUFFER_SIZE > 0
         static uint8_t availableForWrite(void);
         static void flushTX(void);
       #endif
+      static void writeNoHandshake(const uint8_t c);
+
+      #if ENABLED(SERIAL_STATS_DROPPED_RX)
+        FORCE_INLINE static uint32_t dropped() { return rx_dropped_bytes; }
+      #endif
+
+      #if ENABLED(SERIAL_STATS_MAX_RX_QUEUED)
+        FORCE_INLINE static ring_buffer_pos_t rxMaxEnqueued() { return rx_max_enqueued; }
+      #endif  
 
     private:
       static void printNumber(unsigned long, const uint8_t);
diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp
index 0d2de7c55..32258ae58 100644
--- a/Marlin/Marlin_main.cpp
+++ b/Marlin/Marlin_main.cpp
@@ -1098,9 +1098,10 @@ inline void get_serial_commands() {
   /**
    * Loop while serial characters are incoming and the queue is not full
    */
-  while (commands_in_queue < BUFSIZE && MYSERIAL.available() > 0) {
+  int c;
+  while (commands_in_queue < BUFSIZE && (c = MYSERIAL.read()) >= 0) {
 
-    char serial_char = MYSERIAL.read();
+    char serial_char = c;
 
     /**
      * If the character ends the line
@@ -1200,9 +1201,9 @@ inline void get_serial_commands() {
       // The command will be injected when EOL is reached
     }
     else if (serial_char == '\\') {  // Handle escapes
-      if (MYSERIAL.available() > 0) {
+      if ((c = MYSERIAL.read()) >= 0) {
         // if we have one more character, copy it over
-        serial_char = MYSERIAL.read();
+        serial_char = c;
         if (!serial_comment_mode) serial_line_buffer[serial_count++] = serial_char;
       }
       // otherwise do nothing
@@ -13610,6 +13611,15 @@ void loop() {
           // M29 closes the file
           card.closefile();
           SERIAL_PROTOCOLLNPGM(MSG_FILE_SAVED);
+
+          #if ENABLED(SERIAL_STATS_DROPPED_RX)
+            SERIAL_ECHOLNPAIR("Dropped bytes: ", customizedSerial.dropped());
+          #endif
+
+          #if ENABLED(SERIAL_STATS_MAX_RX_QUEUED)
+            SERIAL_ECHOLNPAIR("Max RX Queue Size: ", customizedSerial.rxMaxEnqueued());
+          #endif
+
           ok_to_send();
         }
         else {
diff --git a/Marlin/example_configurations/AlephObjects/TAZ4/Configuration.h b/Marlin/example_configurations/AlephObjects/TAZ4/Configuration.h
index 895d095b0..82200bd9c 100644
--- a/Marlin/example_configurations/AlephObjects/TAZ4/Configuration.h
+++ b/Marlin/example_configurations/AlephObjects/TAZ4/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/AlephObjects/TAZ4/Configuration_adv.h b/Marlin/example_configurations/AlephObjects/TAZ4/Configuration_adv.h
index c19cc2543..01722c8df 100644
--- a/Marlin/example_configurations/AlephObjects/TAZ4/Configuration_adv.h
+++ b/Marlin/example_configurations/AlephObjects/TAZ4/Configuration_adv.h
@@ -753,6 +753,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/AliExpress/CL-260/Configuration.h b/Marlin/example_configurations/AliExpress/CL-260/Configuration.h
index d70c59a4e..c08e54280 100644
--- a/Marlin/example_configurations/AliExpress/CL-260/Configuration.h
+++ b/Marlin/example_configurations/AliExpress/CL-260/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/Anet/A6/Configuration.h b/Marlin/example_configurations/Anet/A6/Configuration.h
index 3b8ab3a37..61b514c4f 100644
--- a/Marlin/example_configurations/Anet/A6/Configuration.h
+++ b/Marlin/example_configurations/Anet/A6/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 115200
 
diff --git a/Marlin/example_configurations/Anet/A6/Configuration_adv.h b/Marlin/example_configurations/Anet/A6/Configuration_adv.h
index 15c9103e9..ed0a7e48d 100644
--- a/Marlin/example_configurations/Anet/A6/Configuration_adv.h
+++ b/Marlin/example_configurations/Anet/A6/Configuration_adv.h
@@ -753,6 +753,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/Anet/A8/Configuration.h b/Marlin/example_configurations/Anet/A8/Configuration.h
index 1912dd458..31e256f55 100644
--- a/Marlin/example_configurations/Anet/A8/Configuration.h
+++ b/Marlin/example_configurations/Anet/A8/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 115200
 
diff --git a/Marlin/example_configurations/Anet/A8/Configuration_adv.h b/Marlin/example_configurations/Anet/A8/Configuration_adv.h
index 52710ab33..c4de04e84 100644
--- a/Marlin/example_configurations/Anet/A8/Configuration_adv.h
+++ b/Marlin/example_configurations/Anet/A8/Configuration_adv.h
@@ -753,6 +753,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/BQ/Hephestos/Configuration.h b/Marlin/example_configurations/BQ/Hephestos/Configuration.h
index ac24821f7..ee4151217 100644
--- a/Marlin/example_configurations/BQ/Hephestos/Configuration.h
+++ b/Marlin/example_configurations/BQ/Hephestos/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 115200
 
diff --git a/Marlin/example_configurations/BQ/Hephestos/Configuration_adv.h b/Marlin/example_configurations/BQ/Hephestos/Configuration_adv.h
index a9b82d02d..2fcad44d2 100644
--- a/Marlin/example_configurations/BQ/Hephestos/Configuration_adv.h
+++ b/Marlin/example_configurations/BQ/Hephestos/Configuration_adv.h
@@ -753,6 +753,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/BQ/Hephestos_2/Configuration.h b/Marlin/example_configurations/BQ/Hephestos_2/Configuration.h
index 4d27fbfeb..d6ce97dd4 100644
--- a/Marlin/example_configurations/BQ/Hephestos_2/Configuration.h
+++ b/Marlin/example_configurations/BQ/Hephestos_2/Configuration.h
@@ -106,8 +106,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 115200
 
diff --git a/Marlin/example_configurations/BQ/Hephestos_2/Configuration_adv.h b/Marlin/example_configurations/BQ/Hephestos_2/Configuration_adv.h
index a95d9bbcc..f609f1538 100644
--- a/Marlin/example_configurations/BQ/Hephestos_2/Configuration_adv.h
+++ b/Marlin/example_configurations/BQ/Hephestos_2/Configuration_adv.h
@@ -753,6 +753,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 32
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/BQ/WITBOX/Configuration.h b/Marlin/example_configurations/BQ/WITBOX/Configuration.h
index 3a9b473f9..f21a580b8 100644
--- a/Marlin/example_configurations/BQ/WITBOX/Configuration.h
+++ b/Marlin/example_configurations/BQ/WITBOX/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 115200
 
diff --git a/Marlin/example_configurations/BQ/WITBOX/Configuration_adv.h b/Marlin/example_configurations/BQ/WITBOX/Configuration_adv.h
index a9b82d02d..2fcad44d2 100644
--- a/Marlin/example_configurations/BQ/WITBOX/Configuration_adv.h
+++ b/Marlin/example_configurations/BQ/WITBOX/Configuration_adv.h
@@ -753,6 +753,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/Cartesio/Configuration.h b/Marlin/example_configurations/Cartesio/Configuration.h
index d711cd126..b4303517f 100644
--- a/Marlin/example_configurations/Cartesio/Configuration.h
+++ b/Marlin/example_configurations/Cartesio/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 115200
 
diff --git a/Marlin/example_configurations/Cartesio/Configuration_adv.h b/Marlin/example_configurations/Cartesio/Configuration_adv.h
index 4272f81bb..af4dadd13 100644
--- a/Marlin/example_configurations/Cartesio/Configuration_adv.h
+++ b/Marlin/example_configurations/Cartesio/Configuration_adv.h
@@ -753,6 +753,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/Creality/CR-10/Configuration.h b/Marlin/example_configurations/Creality/CR-10/Configuration.h
index b0de88336..3111fa4c4 100755
--- a/Marlin/example_configurations/Creality/CR-10/Configuration.h
+++ b/Marlin/example_configurations/Creality/CR-10/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 115200
 
diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h
index 22bb602d3..fcaf37b8b 100644
--- a/Marlin/example_configurations/Felix/Configuration.h
+++ b/Marlin/example_configurations/Felix/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/Felix/Configuration_adv.h b/Marlin/example_configurations/Felix/Configuration_adv.h
index 1ac472edd..6a7ca3e35 100644
--- a/Marlin/example_configurations/Felix/Configuration_adv.h
+++ b/Marlin/example_configurations/Felix/Configuration_adv.h
@@ -753,6 +753,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/Felix/DUAL/Configuration.h b/Marlin/example_configurations/Felix/DUAL/Configuration.h
index e64a0eae7..c44165fc9 100644
--- a/Marlin/example_configurations/Felix/DUAL/Configuration.h
+++ b/Marlin/example_configurations/Felix/DUAL/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/Folger Tech/i3-2020/Configuration.h b/Marlin/example_configurations/Folger Tech/i3-2020/Configuration.h
index a7bc508e7..d75336e8d 100644
--- a/Marlin/example_configurations/Folger Tech/i3-2020/Configuration.h	
+++ b/Marlin/example_configurations/Folger Tech/i3-2020/Configuration.h	
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/Folger Tech/i3-2020/Configuration_adv.h b/Marlin/example_configurations/Folger Tech/i3-2020/Configuration_adv.h
index 2d7991d3c..80dbd7ade 100644
--- a/Marlin/example_configurations/Folger Tech/i3-2020/Configuration_adv.h	
+++ b/Marlin/example_configurations/Folger Tech/i3-2020/Configuration_adv.h	
@@ -753,6 +753,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/Geeetech/GT2560/Configuration.h b/Marlin/example_configurations/Geeetech/GT2560/Configuration.h
index c1862a78d..2e0a7993d 100644
--- a/Marlin/example_configurations/Geeetech/GT2560/Configuration.h
+++ b/Marlin/example_configurations/Geeetech/GT2560/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/Geeetech/I3_Pro_X-GT2560/Configuration.h b/Marlin/example_configurations/Geeetech/I3_Pro_X-GT2560/Configuration.h
index d77728304..d312ce50a 100644
--- a/Marlin/example_configurations/Geeetech/I3_Pro_X-GT2560/Configuration.h
+++ b/Marlin/example_configurations/Geeetech/I3_Pro_X-GT2560/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/Infitary/i3-M508/Configuration.h b/Marlin/example_configurations/Infitary/i3-M508/Configuration.h
index 12e501409..5ccf56a30 100644
--- a/Marlin/example_configurations/Infitary/i3-M508/Configuration.h
+++ b/Marlin/example_configurations/Infitary/i3-M508/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/Infitary/i3-M508/Configuration_adv.h b/Marlin/example_configurations/Infitary/i3-M508/Configuration_adv.h
index 4fad47cab..9fb057b38 100644
--- a/Marlin/example_configurations/Infitary/i3-M508/Configuration_adv.h
+++ b/Marlin/example_configurations/Infitary/i3-M508/Configuration_adv.h
@@ -753,6 +753,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/Malyan/M150/Configuration.h b/Marlin/example_configurations/Malyan/M150/Configuration.h
index d260492fb..8bede2a2e 100644
--- a/Marlin/example_configurations/Malyan/M150/Configuration.h
+++ b/Marlin/example_configurations/Malyan/M150/Configuration.h
@@ -112,8 +112,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 115200
 
diff --git a/Marlin/example_configurations/Malyan/M150/Configuration_adv.h b/Marlin/example_configurations/Malyan/M150/Configuration_adv.h
index 62cb80af7..c17e0ab7b 100644
--- a/Marlin/example_configurations/Malyan/M150/Configuration_adv.h
+++ b/Marlin/example_configurations/Malyan/M150/Configuration_adv.h
@@ -753,6 +753,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
index 4abd8ef67..f5be35ebe 100644
--- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
+++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h
index 38bc93037..b4bb4f0dd 100644
--- a/Marlin/example_configurations/RigidBot/Configuration.h
+++ b/Marlin/example_configurations/RigidBot/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 115200
 
diff --git a/Marlin/example_configurations/RigidBot/Configuration_adv.h b/Marlin/example_configurations/RigidBot/Configuration_adv.h
index c05163065..66858fd6f 100644
--- a/Marlin/example_configurations/RigidBot/Configuration_adv.h
+++ b/Marlin/example_configurations/RigidBot/Configuration_adv.h
@@ -753,6 +753,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h
index f18d75dc6..fc4fb4d1f 100644
--- a/Marlin/example_configurations/SCARA/Configuration.h
+++ b/Marlin/example_configurations/SCARA/Configuration.h
@@ -137,8 +137,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/SCARA/Configuration_adv.h b/Marlin/example_configurations/SCARA/Configuration_adv.h
index a787c5325..8f7b81efe 100644
--- a/Marlin/example_configurations/SCARA/Configuration_adv.h
+++ b/Marlin/example_configurations/SCARA/Configuration_adv.h
@@ -753,6 +753,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/TinyBoy2/Configuration.h b/Marlin/example_configurations/TinyBoy2/Configuration.h
index 212fd0e72..f23269592 100644
--- a/Marlin/example_configurations/TinyBoy2/Configuration.h
+++ b/Marlin/example_configurations/TinyBoy2/Configuration.h
@@ -123,8 +123,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 115200
 
diff --git a/Marlin/example_configurations/TinyBoy2/Configuration_adv.h b/Marlin/example_configurations/TinyBoy2/Configuration_adv.h
index ebd3dfe96..472a7bc27 100644
--- a/Marlin/example_configurations/TinyBoy2/Configuration_adv.h
+++ b/Marlin/example_configurations/TinyBoy2/Configuration_adv.h
@@ -753,6 +753,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 64
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/Velleman/K8200/Configuration.h b/Marlin/example_configurations/Velleman/K8200/Configuration.h
index 2a6d66434..d833d6cc3 100644
--- a/Marlin/example_configurations/Velleman/K8200/Configuration.h
+++ b/Marlin/example_configurations/Velleman/K8200/Configuration.h
@@ -123,8 +123,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/Velleman/K8200/Configuration_adv.h b/Marlin/example_configurations/Velleman/K8200/Configuration_adv.h
index 88a2ceb11..057094b9e 100644
--- a/Marlin/example_configurations/Velleman/K8200/Configuration_adv.h
+++ b/Marlin/example_configurations/Velleman/K8200/Configuration_adv.h
@@ -766,6 +766,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 128
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/Velleman/K8400/Configuration.h b/Marlin/example_configurations/Velleman/K8400/Configuration.h
index bc32236b1..77eed969b 100644
--- a/Marlin/example_configurations/Velleman/K8400/Configuration.h
+++ b/Marlin/example_configurations/Velleman/K8400/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/Velleman/K8400/Configuration_adv.h b/Marlin/example_configurations/Velleman/K8400/Configuration_adv.h
index 280c3e169..71a5d629d 100644
--- a/Marlin/example_configurations/Velleman/K8400/Configuration_adv.h
+++ b/Marlin/example_configurations/Velleman/K8400/Configuration_adv.h
@@ -753,6 +753,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/Velleman/K8400/Dual-head/Configuration.h b/Marlin/example_configurations/Velleman/K8400/Dual-head/Configuration.h
index 7ff206580..6da2a7819 100644
--- a/Marlin/example_configurations/Velleman/K8400/Dual-head/Configuration.h
+++ b/Marlin/example_configurations/Velleman/K8400/Dual-head/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
index 5d4e3ffb1..0f79ff42f 100644
--- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h
+++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h
index 76345829b..d294bc3da 100644
--- a/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h
+++ b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h
index 64c559972..3f60a00d2 100644
--- a/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h
@@ -755,6 +755,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h
index 7bd1d1e85..d78c82423 100644
--- a/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h
+++ b/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h
index b14ceda17..c5d4280dc 100644
--- a/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h
@@ -755,6 +755,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h
index fe946138c..e8accf616 100644
--- a/Marlin/example_configurations/delta/generic/Configuration.h
+++ b/Marlin/example_configurations/delta/generic/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/delta/generic/Configuration_adv.h b/Marlin/example_configurations/delta/generic/Configuration_adv.h
index b14ceda17..c5d4280dc 100644
--- a/Marlin/example_configurations/delta/generic/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/generic/Configuration_adv.h
@@ -755,6 +755,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
index 9d1b2aca4..1e351e31a 100644
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
index b14ceda17..c5d4280dc 100644
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
@@ -755,6 +755,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
index 714764917..d238919cf 100644
--- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
@@ -111,8 +111,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 115200
 
diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
index 6af63abba..748f2264e 100644
--- a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
@@ -760,6 +760,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration.h b/Marlin/example_configurations/delta/kossel_xl/Configuration.h
index 818e95698..5e2d2bc3e 100644
--- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h
index 0349ba339..b1d13c617 100644
--- a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h
@@ -755,6 +755,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/gCreate/gMax1.5+/Configuration.h b/Marlin/example_configurations/gCreate/gMax1.5+/Configuration.h
index d2c91a2f9..9d640540e 100644
--- a/Marlin/example_configurations/gCreate/gMax1.5+/Configuration.h
+++ b/Marlin/example_configurations/gCreate/gMax1.5+/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/gCreate/gMax1.5+/Configuration_adv.h b/Marlin/example_configurations/gCreate/gMax1.5+/Configuration_adv.h
index a968ab919..5d6f56aee 100644
--- a/Marlin/example_configurations/gCreate/gMax1.5+/Configuration_adv.h
+++ b/Marlin/example_configurations/gCreate/gMax1.5+/Configuration_adv.h
@@ -753,6 +753,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 32
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h
index 6605e8721..8b59a91d2 100644
--- a/Marlin/example_configurations/makibox/Configuration.h
+++ b/Marlin/example_configurations/makibox/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/makibox/Configuration_adv.h b/Marlin/example_configurations/makibox/Configuration_adv.h
index e9990ecb5..ecf14adeb 100644
--- a/Marlin/example_configurations/makibox/Configuration_adv.h
+++ b/Marlin/example_configurations/makibox/Configuration_adv.h
@@ -753,6 +753,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
index ce1544f8c..af581d430 100644
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 250000
 
diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
index 3fe2705e2..6b174eeec 100644
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
@@ -753,6 +753,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/example_configurations/wt150/Configuration.h b/Marlin/example_configurations/wt150/Configuration.h
index 4a532b3e8..2a0e64984 100644
--- a/Marlin/example_configurations/wt150/Configuration.h
+++ b/Marlin/example_configurations/wt150/Configuration.h
@@ -107,8 +107,9 @@
  *
  * 250000 works in most cases, but you might try a lower speed if
  * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
  *
- * :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
 #define BAUDRATE 115200
 
diff --git a/Marlin/example_configurations/wt150/Configuration_adv.h b/Marlin/example_configurations/wt150/Configuration_adv.h
index 56015347b..c9483b6aa 100644
--- a/Marlin/example_configurations/wt150/Configuration_adv.h
+++ b/Marlin/example_configurations/wt150/Configuration_adv.h
@@ -753,6 +753,28 @@
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
 #define TX_BUFFER_SIZE 0
 
+// Host Receive Buffer Size
+// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
+// To use flow control, set this buffer size to at least 1024 bytes.
+// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
+//#define RX_BUFFER_SIZE 1024
+
+#if RX_BUFFER_SIZE >= 1024
+  // Enable to have the controller send XON/XOFF control characters to
+  // the host to signal the RX buffer is becoming full.
+  //#define SERIAL_XON_XOFF
+#endif
+
+#if ENABLED(SDSUPPORT)
+  // Enable this option to collect and display the maximum
+  // RX queue usage after transferring a file to SD.
+  //#define SERIAL_STATS_MAX_RX_QUEUED
+
+  // Enable this option to collect and display the number
+  // of dropped bytes after a file transfer to SD.
+  //#define SERIAL_STATS_DROPPED_RX
+#endif
+
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
diff --git a/Marlin/macros.h b/Marlin/macros.h
index 3b79ba9b8..05433597f 100644
--- a/Marlin/macros.h
+++ b/Marlin/macros.h
@@ -99,6 +99,9 @@
 #define CBI(n,b) (n &= ~_BV(b))
 #define SET_BIT(n,b,value) (n) ^= ((-value)^(n)) & (_BV(b))
 
+// Macro to check that a number if a power if 2
+#define IS_POWER_OF_2(x) ((x) && !((x) & ((x) - 1)))
+
 // Macros for maths shortcuts
 #ifndef M_PI
   #define M_PI 3.14159265358979323846