diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index be56f8088..19d4710b1 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 10  // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.
diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp
index 37b15a58a..d51f2f797 100644
--- a/Marlin/Marlin_main.cpp
+++ b/Marlin/Marlin_main.cpp
@@ -4399,14 +4399,14 @@ inline void gcode_M109() {
   // Try to calculate a ballpark safe margin by halving EXTRUDE_MINTEMP
   if (wants_to_cool && degTargetHotend(target_extruder) < (EXTRUDE_MINTEMP)/2) return;
 
-  #ifdef TEMP_RESIDENCY_TIME
+  #if TEMP_RESIDENCY_TIME > 0
     millis_t residency_start_ms = 0;
     // Loop until the temperature has stabilized
     #define TEMP_CONDITIONS (!residency_start_ms || PENDING(now, residency_start_ms + (TEMP_RESIDENCY_TIME) * 1000UL))
   #else
     // Loop until the temperature is very close target
     #define TEMP_CONDITIONS (wants_to_cool ? isCoolingHotend(target_extruder) : isHeatingHotend(target_extruder))
-  #endif //TEMP_RESIDENCY_TIME
+  #endif //TEMP_RESIDENCY_TIME > 0
 
   cancel_heatup = false;
   millis_t now, next_temp_ms = 0;
@@ -4417,7 +4417,7 @@ inline void gcode_M109() {
       #if HAS_TEMP_HOTEND || HAS_TEMP_BED
         print_heaterstates();
       #endif
-      #ifdef TEMP_RESIDENCY_TIME
+      #if TEMP_RESIDENCY_TIME > 0
         SERIAL_PROTOCOLPGM(" W:");
         if (residency_start_ms) {
           long rem = (((TEMP_RESIDENCY_TIME) * 1000UL) - (now - residency_start_ms)) / 1000UL;
@@ -4434,7 +4434,7 @@ inline void gcode_M109() {
     idle();
     refresh_cmd_timeout(); // to prevent stepper_inactive_time from running out
 
-    #ifdef TEMP_RESIDENCY_TIME
+    #if TEMP_RESIDENCY_TIME > 0
 
       float temp_diff = fabs(degTargetHotend(target_extruder) - degHotend(target_extruder));
 
@@ -4447,7 +4447,7 @@ inline void gcode_M109() {
         residency_start_ms = millis();
       }
 
-    #endif //TEMP_RESIDENCY_TIME
+    #endif //TEMP_RESIDENCY_TIME > 0
 
   } while (!cancel_heatup && TEMP_CONDITIONS);
 
@@ -4472,20 +4472,57 @@ inline void gcode_M109() {
     // Exit if S<lower>, continue if S<higher>, R<lower>, or R<higher>
     if (no_wait_for_cooling && wants_to_cool) return;
 
+    #if TEMP_BED_RESIDENCY_TIME > 0
+      millis_t residency_start_ms = 0;
+      // Loop until the temperature has stabilized
+      #define TEMP_BED_CONDITIONS (!residency_start_ms || PENDING(now, residency_start_ms + (TEMP_BED_RESIDENCY_TIME) * 1000UL))
+    #else
+      // Loop until the temperature is very close target
+      #define TEMP_BED_CONDITIONS (wants_to_cool ? isCoolingBed() : isHeatingBed())
+    #endif //TEMP_BED_RESIDENCY_TIME > 0
+
     cancel_heatup = false;
-    millis_t next_temp_ms = 0;
+    millis_t now, next_temp_ms = 0;
 
     // Wait for temperature to come close enough
     do {
-      millis_t now = millis();
+      now = millis();
       if (ELAPSED(now, next_temp_ms)) { //Print Temp Reading every 1 second while heating up.
         next_temp_ms = now + 1000UL;
         print_heaterstates();
-        SERIAL_EOL;
+        #if TEMP_BED_RESIDENCY_TIME > 0
+          SERIAL_PROTOCOLPGM(" W:");
+          if (residency_start_ms) {
+            long rem = (((TEMP_BED_RESIDENCY_TIME) * 1000UL) - (now - residency_start_ms)) / 1000UL;
+            SERIAL_PROTOCOLLN(rem);
+          }
+          else {
+            SERIAL_PROTOCOLLNPGM("?");
+          }
+        #else
+          SERIAL_EOL;
+        #endif
       }
+
       idle();
       refresh_cmd_timeout(); // to prevent stepper_inactive_time from running out
-    } while (!cancel_heatup && (wants_to_cool ? isCoolingBed() : isHeatingBed()));
+
+      #if TEMP_BED_RESIDENCY_TIME > 0
+
+        float temp_diff = fabs(degBed() - degTargetBed());
+
+        if (!residency_start_ms) {
+          // Start the TEMP_BED_RESIDENCY_TIME timer when we reach target temp for the first time.
+          if (temp_diff < TEMP_BED_WINDOW) residency_start_ms = millis();
+        }
+        else if (temp_diff > TEMP_BED_HYSTERESIS) {
+          // Restart the timer whenever the temperature falls outside the hysteresis.
+          residency_start_ms = millis();
+        }
+
+      #endif //TEMP_BED_RESIDENCY_TIME > 0
+
+    } while (!cancel_heatup && TEMP_BED_CONDITIONS);
     LCD_MESSAGEPGM(MSG_BED_DONE);
   }
 
diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h
index 894275b4a..569ba1fd4 100644
--- a/Marlin/example_configurations/Felix/Configuration.h
+++ b/Marlin/example_configurations/Felix/Configuration.h
@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 15  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.
diff --git a/Marlin/example_configurations/Felix/Configuration_DUAL.h b/Marlin/example_configurations/Felix/Configuration_DUAL.h
index 63183fa0f..8830722cc 100644
--- a/Marlin/example_configurations/Felix/Configuration_DUAL.h
+++ b/Marlin/example_configurations/Felix/Configuration_DUAL.h
@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 15  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.
diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h
index 5109d4a5a..9d8259305 100644
--- a/Marlin/example_configurations/Hephestos/Configuration.h
+++ b/Marlin/example_configurations/Hephestos/Configuration.h
@@ -195,11 +195,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.
diff --git a/Marlin/example_configurations/Hephestos_2/Configuration.h b/Marlin/example_configurations/Hephestos_2/Configuration.h
index 95051ebe2..98117fa87 100644
--- a/Marlin/example_configurations/Hephestos_2/Configuration.h
+++ b/Marlin/example_configurations/Hephestos_2/Configuration.h
@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.
diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h
index 57c2ce44c..3f0bac3ab 100644
--- a/Marlin/example_configurations/K8200/Configuration.h
+++ b/Marlin/example_configurations/K8200/Configuration.h
@@ -199,11 +199,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.
diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
index 426f1afcc..c34981fa2 100644
--- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
+++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.
diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h
index bb3581809..928ac5fd0 100644
--- a/Marlin/example_configurations/RigidBot/Configuration.h
+++ b/Marlin/example_configurations/RigidBot/Configuration.h
@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 //#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.
diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h
index c9462a208..8c1167aa1 100644
--- a/Marlin/example_configurations/SCARA/Configuration.h
+++ b/Marlin/example_configurations/SCARA/Configuration.h
@@ -217,11 +217,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 3  // (seconds)
 #define TEMP_HYSTERESIS 2       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.
diff --git a/Marlin/example_configurations/TAZ4/Configuration.h b/Marlin/example_configurations/TAZ4/Configuration.h
index a1ec0f838..8d32b6c77 100644
--- a/Marlin/example_configurations/TAZ4/Configuration.h
+++ b/Marlin/example_configurations/TAZ4/Configuration.h
@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.
diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h
index b645c0a9d..db3544f04 100644
--- a/Marlin/example_configurations/WITBOX/Configuration.h
+++ b/Marlin/example_configurations/WITBOX/Configuration.h
@@ -195,11 +195,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.
diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
index 05eb12ebe..3888609eb 100644
--- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h
+++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.
diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration.h b/Marlin/example_configurations/delta/biv2.5/Configuration.h
index da5c70437..7591f16b5 100644
--- a/Marlin/example_configurations/delta/biv2.5/Configuration.h
+++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h
@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.
diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h
index 5272fb224..3646b3b88 100644
--- a/Marlin/example_configurations/delta/generic/Configuration.h
+++ b/Marlin/example_configurations/delta/generic/Configuration.h
@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.
diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
index 0167a59e5..7e63f32c2 100644
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 5
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.
diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
index 0b4cbb408..81f986c91 100644
--- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
@@ -198,11 +198,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.
diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration.h b/Marlin/example_configurations/delta/kossel_xl/Configuration.h
index 8f06c1c4b..318418007 100644
--- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h
@@ -215,11 +215,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.
diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h
index 4c80a4200..fa0cb56e0 100644
--- a/Marlin/example_configurations/makibox/Configuration.h
+++ b/Marlin/example_configurations/makibox/Configuration.h
@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.
diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
index 30042f36b..727061be6 100644
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
@@ -192,11 +192,16 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-// Actual temperature must be close to target for this long before M109 returns success
+// Extruder temperature must be close to target for this long before M109 returns success
 #define TEMP_RESIDENCY_TIME 10  // (seconds)
 #define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
 #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
 
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 0   // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
 // The minimal temperature defines the temperature below which the heater will not be enabled It is used
 // to check that the wiring to the thermistor is not broken.
 // Otherwise this would lead to the heater being powered on all the time.