diff --git a/Marlin/Conditionals.h b/Marlin/Conditionals.h
index 7063b198e..205616a05 100644
--- a/Marlin/Conditionals.h
+++ b/Marlin/Conditionals.h
@@ -275,17 +275,25 @@
   #include "Arduino.h"
 
   /**
-   * ENDSTOPPULLUPS
+   * Set ENDSTOPPULLUPS for unused endstop switches
    */
   #if ENABLED(ENDSTOPPULLUPS)
-    #if DISABLED(DISABLE_MAX_ENDSTOPS)
+    #if DISABLED(USE_XMAX_PLUG)
       #define ENDSTOPPULLUP_XMAX
+    #endif
+    #if DISABLED(USE_YMAX_PLUG)
       #define ENDSTOPPULLUP_YMAX
+    #endif
+    #if DISABLED(USE_ZMAX_PLUG)
       #define ENDSTOPPULLUP_ZMAX
     #endif
-    #if DISABLED(DISABLE_MIN_ENDSTOPS)
+    #if DISABLED(USE_XMIN_PLUG)
       #define ENDSTOPPULLUP_XMIN
+    #endif
+    #if DISABLED(USE_YMIN_PLUG)
       #define ENDSTOPPULLUP_YMIN
+    #endif
+    #if DISABLED(USE_ZMIN_PLUG)
       #define ENDSTOPPULLUP_ZMIN
     #endif
     #if DISABLED(DISABLE_Z_MIN_PROBE_ENDSTOP)
@@ -503,6 +511,47 @@
 
   #define ARRAY_BY_EXTRUDERS1(v1) ARRAY_BY_EXTRUDERS(v1, v1, v1, v1)
 
+  /**
+   * Z_DUAL_ENDSTOPS endstop reassignment
+   */
+  #if ENABLED(Z_DUAL_ENDSTOPS)
+    #define _XMIN_ 100
+    #define _YMIN_ 200
+    #define _ZMIN_ 300
+    #define _XMAX_ 101
+    #define _YMAX_ 201
+    #define _ZMAX_ 301
+    const bool Z2_MAX_ENDSTOP_INVERTING =
+      #if Z2_USE_ENDSTOP == _XMAX_
+        X_MAX_ENDSTOP_INVERTING
+        #define Z2_MAX_PIN X_MAX_PIN
+        #undef USE_XMAX_PLUG
+      #elif Z2_USE_ENDSTOP == _YMAX_
+        Y_MAX_ENDSTOP_INVERTING
+        #define Z2_MAX_PIN Y_MAX_PIN
+        #undef USE_YMAX_PLUG
+      #elif Z2_USE_ENDSTOP == _ZMAX_
+        Z_MAX_ENDSTOP_INVERTING
+        #define Z2_MAX_PIN Z_MAX_PIN
+        #undef USE_ZMAX_PLUG
+      #elif Z2_USE_ENDSTOP == _XMIN_
+        X_MIN_ENDSTOP_INVERTING
+        #define Z2_MAX_PIN X_MIN_PIN
+        #undef USE_XMIN_PLUG
+      #elif Z2_USE_ENDSTOP == _YMIN_
+        Y_MIN_ENDSTOP_INVERTING
+        #define Z2_MAX_PIN Y_MIN_PIN
+        #undef USE_YMIN_PLUG
+      #elif Z2_USE_ENDSTOP == _ZMIN_
+        Z_MIN_ENDSTOP_INVERTING
+        #define Z2_MAX_PIN Z_MIN_PIN
+        #undef USE_ZMIN_PLUG
+      #else
+        0
+      #endif
+    ;
+  #endif
+
   /**
    * Shorthand for pin tests, used wherever needed
    */
diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 8debc70bd..ddd72d11a 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -346,8 +346,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -370,8 +384,6 @@ const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 84f001fb8..4dd7739d2 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -201,9 +201,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS
diff --git a/Marlin/SanityCheck.h b/Marlin/SanityCheck.h
index fb45e77b9..75bb4893a 100644
--- a/Marlin/SanityCheck.h
+++ b/Marlin/SanityCheck.h
@@ -419,6 +419,19 @@
   #error TEMP_SENSOR_0 is required.
 #endif
 
+/**
+ * Endstops
+ */
+#if DISABLED(USE_XMIN_PLUG) && DISABLED(USE_XMAX_PLUG) && !(ENABLED(Z_DUAL_ENDSTOPS) && Z2_USE_ENDSTOP >= _XMAX_ && Z2_USE_ENDSTOP <= _XMIN_)
+ #error You must enable USE_XMIN_PLUG or USE_XMAX_PLUG
+#elif DISABLED(USE_YMIN_PLUG) && DISABLED(USE_YMAX_PLUG) && !(ENABLED(Z_DUAL_ENDSTOPS) && Z2_USE_ENDSTOP >= _YMAX_ && Z2_USE_ENDSTOP <= _YMIN_)
+ #error You must enable USE_YMIN_PLUG or USE_YMAX_PLUG
+#elif DISABLED(USE_ZMIN_PLUG) && DISABLED(USE_ZMAX_PLUG) && !(ENABLED(Z_DUAL_ENDSTOPS) && Z2_USE_ENDSTOP >= _ZMAX_ && Z2_USE_ENDSTOP <= _ZMIN_)
+ #error You must enable USE_ZMIN_PLUG or USE_ZMAX_PLUG
+#elif ENABLED(Z_DUAL_ENDSTOPS) && !Z2_USE_ENDSTOP
+ #error You must set Z2_USE_ENDSTOP with Z_DUAL_ENDSTOPS
+#endif
+
 /**
  * Warnings for old configurations
  */
@@ -445,17 +458,21 @@
 #elif defined(CUSTOM_MENDEL_NAME)
   #error CUSTOM_MENDEL_NAME is now CUSTOM_MACHINE_NAME. Please update your configuration.
 #elif defined(HAS_AUTOMATIC_VERSIONING)
-  #error HAS_AUTOMATIC_VERSIONING deprecated - use USE_AUTOMATIC_VERSIONING instead
+  #error HAS_AUTOMATIC_VERSIONING is now USE_AUTOMATIC_VERSIONING. Please update your configuration.
 #elif defined(ENABLE_AUTO_BED_LEVELING)
-  #error ENABLE_AUTO_BED_LEVELING deprecated - use AUTO_BED_LEVELING_FEATURE instead
+  #error ENABLE_AUTO_BED_LEVELING is now AUTO_BED_LEVELING_FEATURE. Please update your configuration.
 #elif defined(SDSLOW)
-  #error SDSLOW deprecated - set SPI_SPEED to SPI_HALF_SPEED instead
+  #error SDSLOW deprecated. Set SPI_SPEED to SPI_HALF_SPEED instead.
 #elif defined(SDEXTRASLOW)
-  #error SDEXTRASLOW deprecated - set SPI_SPEED to SPI_QUARTER_SPEED instead
+  #error SDEXTRASLOW deprecated. Set SPI_SPEED to SPI_QUARTER_SPEED instead.
 #elif defined(Z_RAISE_BEFORE_HOMING)
   #error Z_RAISE_BEFORE_HOMING is deprecated. Use MIN_Z_HEIGHT_FOR_HOMING instead.
 #elif defined(FILAMENT_SENSOR)
   #error FILAMENT_SENSOR is deprecated. Use FILAMENT_WIDTH_SENSOR instead.
+#elif defined(DISABLE_MAX_ENDSTOPS) || defined(DISABLE_MIN_ENDSTOPS)
+  #error DISABLE_MAX_ENDSTOPS and DISABLE_MIN_ENDSTOPS deprecated. Use individual USE_*_PLUG options instead.
+#elif ENABLED(Z_DUAL_ENDSTOPS) && !defined(Z2_USE_ENDSTOP)
+  #error Z_DUAL_ENDSTOPS settings are simplified. Just set Z2_USE_ENDSTOP to the endstop you want to repurpose for Z2
 #endif
 
 #endif //SANITYCHECK_H
diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h
index 3fd1646da..e91e927c8 100644
--- a/Marlin/example_configurations/Felix/Configuration.h
+++ b/Marlin/example_configurations/Felix/Configuration.h
@@ -328,8 +328,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -352,8 +366,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================
diff --git a/Marlin/example_configurations/Felix/Configuration_DUAL.h b/Marlin/example_configurations/Felix/Configuration_DUAL.h
index 553c2dc60..29507abaa 100644
--- a/Marlin/example_configurations/Felix/Configuration_DUAL.h
+++ b/Marlin/example_configurations/Felix/Configuration_DUAL.h
@@ -325,8 +325,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -349,8 +363,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================
diff --git a/Marlin/example_configurations/Felix/Configuration_adv.h b/Marlin/example_configurations/Felix/Configuration_adv.h
index 5608d4b39..d5b2942d6 100644
--- a/Marlin/example_configurations/Felix/Configuration_adv.h
+++ b/Marlin/example_configurations/Felix/Configuration_adv.h
@@ -201,9 +201,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS
diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h
index 1d6faab46..cac62233f 100644
--- a/Marlin/example_configurations/Hephestos/Configuration.h
+++ b/Marlin/example_configurations/Hephestos/Configuration.h
@@ -338,8 +338,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -362,8 +376,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================
diff --git a/Marlin/example_configurations/Hephestos/Configuration_adv.h b/Marlin/example_configurations/Hephestos/Configuration_adv.h
index fcdee236a..b92a73798 100644
--- a/Marlin/example_configurations/Hephestos/Configuration_adv.h
+++ b/Marlin/example_configurations/Hephestos/Configuration_adv.h
@@ -201,9 +201,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS
diff --git a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h
index 3131e10b2..b5a451c53 100644
--- a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h
+++ b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h
@@ -201,9 +201,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS
diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h
index e803d3e2b..3bb350ddd 100644
--- a/Marlin/example_configurations/K8200/Configuration.h
+++ b/Marlin/example_configurations/K8200/Configuration.h
@@ -363,8 +363,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -387,8 +401,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================
diff --git a/Marlin/example_configurations/K8200/Configuration_adv.h b/Marlin/example_configurations/K8200/Configuration_adv.h
index f5b6e70ea..5c47bde71 100644
--- a/Marlin/example_configurations/K8200/Configuration_adv.h
+++ b/Marlin/example_configurations/K8200/Configuration_adv.h
@@ -207,9 +207,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS
diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
index 80e9d3519..487e8d876 100644
--- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
+++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
@@ -346,8 +346,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -370,8 +384,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================
diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h
index 3147bb0e0..e5c98d479 100644
--- a/Marlin/example_configurations/RigidBot/Configuration.h
+++ b/Marlin/example_configurations/RigidBot/Configuration.h
@@ -340,8 +340,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -364,8 +378,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================
diff --git a/Marlin/example_configurations/RigidBot/Configuration_adv.h b/Marlin/example_configurations/RigidBot/Configuration_adv.h
index c93dde281..17e19b083 100644
--- a/Marlin/example_configurations/RigidBot/Configuration_adv.h
+++ b/Marlin/example_configurations/RigidBot/Configuration_adv.h
@@ -201,9 +201,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS
diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h
index 2320abc06..c09a7ae82 100644
--- a/Marlin/example_configurations/SCARA/Configuration.h
+++ b/Marlin/example_configurations/SCARA/Configuration.h
@@ -354,8 +354,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+//#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 //#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -378,8 +392,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================
diff --git a/Marlin/example_configurations/SCARA/Configuration_adv.h b/Marlin/example_configurations/SCARA/Configuration_adv.h
index 627067d77..1b09057ed 100644
--- a/Marlin/example_configurations/SCARA/Configuration_adv.h
+++ b/Marlin/example_configurations/SCARA/Configuration_adv.h
@@ -201,9 +201,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS
diff --git a/Marlin/example_configurations/TAZ4/Configuration.h b/Marlin/example_configurations/TAZ4/Configuration.h
index 8c7fb0388..7dd94b7ae 100644
--- a/Marlin/example_configurations/TAZ4/Configuration.h
+++ b/Marlin/example_configurations/TAZ4/Configuration.h
@@ -367,8 +367,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -391,8 +405,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================
diff --git a/Marlin/example_configurations/TAZ4/Configuration_adv.h b/Marlin/example_configurations/TAZ4/Configuration_adv.h
index c052253a1..62dde979c 100644
--- a/Marlin/example_configurations/TAZ4/Configuration_adv.h
+++ b/Marlin/example_configurations/TAZ4/Configuration_adv.h
@@ -209,9 +209,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS
diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h
index 9d6c5b7f2..6f96bbf42 100644
--- a/Marlin/example_configurations/WITBOX/Configuration.h
+++ b/Marlin/example_configurations/WITBOX/Configuration.h
@@ -338,8 +338,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -362,8 +376,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================
diff --git a/Marlin/example_configurations/WITBOX/Configuration_adv.h b/Marlin/example_configurations/WITBOX/Configuration_adv.h
index fcdee236a..b92a73798 100644
--- a/Marlin/example_configurations/WITBOX/Configuration_adv.h
+++ b/Marlin/example_configurations/WITBOX/Configuration_adv.h
@@ -201,9 +201,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS
diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
index 8effe9d89..9620b49ff 100644
--- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h
+++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
@@ -346,8 +346,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -370,8 +384,6 @@ const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================
diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration.h b/Marlin/example_configurations/delta/biv2.5/Configuration.h
index feff6f4b7..9c91da9d7 100644
--- a/Marlin/example_configurations/delta/biv2.5/Configuration.h
+++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h
@@ -381,8 +381,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+//#define USE_XMIN_PLUG
+//#define USE_YMIN_PLUG
+//#define USE_ZMIN_PLUG
+#define USE_XMAX_PLUG
+#define USE_YMAX_PLUG
+#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -405,8 +419,6 @@ const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-#define DISABLE_MIN_ENDSTOPS // Deltas only use min endstops for probing.
 
 //===========================================================================
 //============================= Z Probe Options =============================
diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h
index 85734dc41..491cf38f3 100644
--- a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h
@@ -201,9 +201,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS
diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h
index 93d7f8ad7..5beb3f4b5 100644
--- a/Marlin/example_configurations/delta/generic/Configuration.h
+++ b/Marlin/example_configurations/delta/generic/Configuration.h
@@ -381,8 +381,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+//#define USE_XMIN_PLUG
+//#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG // a Z probe
+#define USE_XMAX_PLUG
+#define USE_YMAX_PLUG
+#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -405,8 +419,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-#define DISABLE_MIN_ENDSTOPS // Deltas only use min endstops for probing.
 
 //===========================================================================
 //============================= Z Probe Options =============================
diff --git a/Marlin/example_configurations/delta/generic/Configuration_adv.h b/Marlin/example_configurations/delta/generic/Configuration_adv.h
index 006502e7a..414d4de32 100644
--- a/Marlin/example_configurations/delta/generic/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/generic/Configuration_adv.h
@@ -201,9 +201,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS
diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
index cde4707f3..d88d12dc6 100644
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
@@ -381,8 +381,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+//#define USE_XMIN_PLUG
+//#define USE_YMIN_PLUG
+//#define USE_ZMIN_PLUG
+#define USE_XMAX_PLUG
+#define USE_YMAX_PLUG
+#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -405,8 +419,6 @@ const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS // Deltas only use min endstops for probing.
 
 //===========================================================================
 //============================= Z Probe Options =============================
diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
index 4b93e4647..a9de9f43a 100644
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
@@ -201,9 +201,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS
diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
index 5255b7acc..6d769fb32 100644
--- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
@@ -370,8 +370,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+//#define USE_XMIN_PLUG
+//#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG // a Z probe
+#define USE_XMAX_PLUG
+#define USE_YMAX_PLUG
+#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -394,8 +408,6 @@ const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS // Deltas only use min endstops for probing.
 
 //===========================================================================
 //============================= Z Probe Options =============================
diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
index b3fec75c5..29d9607ac 100644
--- a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
@@ -206,9 +206,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS
diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h
index 44e7942eb..23829cbbc 100644
--- a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h
@@ -201,9 +201,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS
diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h
index bd550066c..6ccd700aa 100644
--- a/Marlin/example_configurations/makibox/Configuration.h
+++ b/Marlin/example_configurations/makibox/Configuration.h
@@ -349,8 +349,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -373,8 +387,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================
diff --git a/Marlin/example_configurations/makibox/Configuration_adv.h b/Marlin/example_configurations/makibox/Configuration_adv.h
index 9b131b329..301f362b6 100644
--- a/Marlin/example_configurations/makibox/Configuration_adv.h
+++ b/Marlin/example_configurations/makibox/Configuration_adv.h
@@ -201,9 +201,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS
diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
index b7431e9d2..85f2258f4 100644
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
@@ -336,8 +336,22 @@
 // Enable this option for Toshiba steppers
 #define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -360,8 +374,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS
 
 //===========================================================================
 //============================= Z Probe Options =============================
diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
index 37d3bd81e..0c62e7911 100644
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
@@ -201,9 +201,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS
diff --git a/Marlin/macros.h b/Marlin/macros.h
index 4fce8eb53..be5e8cf2c 100644
--- a/Marlin/macros.h
+++ b/Marlin/macros.h
@@ -24,8 +24,8 @@
 #define MACROS_H
 
 // Macros to make a string from a macro
-#define STRINGIFY_(n) #n
-#define STRINGIFY(n) STRINGIFY_(n)
+#define STRINGIFY_(M) #M
+#define STRINGIFY(M) STRINGIFY_(M)
 
 // Macros for bit masks
 #define TEST(n,b) (((n)&_BV(b))!=0)
diff --git a/Marlin/pins.h b/Marlin/pins.h
index 4afa2b616..eb37f87af 100644
--- a/Marlin/pins.h
+++ b/Marlin/pins.h
@@ -209,55 +209,37 @@
   #endif
 #endif
 
-#if ENABLED(DISABLE_MAX_ENDSTOPS)
-  #undef X_MAX_PIN
-  #undef Y_MAX_PIN
-  #undef Z_MAX_PIN
-  #define X_MAX_PIN          -1
-  #define Y_MAX_PIN          -1
-  #define Z_MAX_PIN          -1
-#endif
-
-#if ENABLED(DISABLE_MIN_ENDSTOPS)
-  #undef X_MIN_PIN
-  #undef Y_MIN_PIN
-  #undef Z_MIN_PIN
-  #define X_MIN_PIN          -1
-  #define Y_MIN_PIN          -1
-  #define Z_MIN_PIN          -1
-#endif
-
 #if ENABLED(DISABLE_Z_MIN_PROBE_ENDSTOP) || DISABLED(Z_MIN_PROBE_ENDSTOP) // Allow code to compile regardless of Z_MIN_PROBE_ENDSTOP setting.
   #undef Z_MIN_PROBE_PIN
   #define Z_MIN_PROBE_PIN    -1
 #endif
 
-#if ENABLED(DISABLE_XMAX_ENDSTOP)
+#if DISABLED(USE_XMAX_PLUG)
   #undef X_MAX_PIN
   #define X_MAX_PIN          -1
 #endif
 
-#if ENABLED(DISABLE_XMIN_ENDSTOP)
-  #undef X_MIN_PIN
-  #define X_MIN_PIN          -1
-#endif
-
-#if ENABLED(DISABLE_YMAX_ENDSTOP)
+#if DISABLED(USE_YMAX_PLUG)
   #undef Y_MAX_PIN
   #define Y_MAX_PIN          -1
 #endif
 
-#if ENABLED(DISABLE_YMIN_ENDSTOP)
-  #undef Y_MIN_PIN
-  #define Y_MIN_PIN          -1
-#endif
-
-#if ENABLED(DISABLE_ZMAX_ENDSTOP)
+#if DISABLED(USE_ZMAX_PLUG)
   #undef Z_MAX_PIN
   #define Z_MAX_PIN          -1
 #endif
 
-#if ENABLED(DISABLE_ZMIN_ENDSTOP)
+#if DISABLED(USE_XMIN_PLUG)
+  #undef X_MIN_PIN
+  #define X_MIN_PIN          -1
+#endif
+
+#if DISABLED(USE_YMIN_PLUG)
+  #undef Y_MIN_PIN
+  #define Y_MIN_PIN          -1
+#endif
+
+#if DISABLED(USE_ZMIN_PLUG)
   #undef Z_MIN_PIN
   #define Z_MIN_PIN          -1
 #endif
diff --git a/Marlin/pins_FELIX2.h b/Marlin/pins_FELIX2.h
index 79d8332ad..e5aa87922 100644
--- a/Marlin/pins_FELIX2.h
+++ b/Marlin/pins_FELIX2.h
@@ -29,8 +29,6 @@
 #undef HEATER_1_PIN
 #define HEATER_1_PIN        7 // EXTRUDER 2
 
-#define DISABLE_MAX_ENDSTOPS
-
 #undef SDPOWER
 #define SDPOWER             1