|
|
|
|
@ -61,23 +61,23 @@
|
|
|
|
|
#define SDSS 53
|
|
|
|
|
#define LED_PIN 13
|
|
|
|
|
|
|
|
|
|
#if MB(RAMPS_13_EEB) && defined(FILAMENT_SENSOR) // FMM added for Filament Extruder
|
|
|
|
|
#if MB(RAMPS_13_EEB) && ENABLED(FILAMENT_SENSOR) // FMM added for Filament Extruder
|
|
|
|
|
// define analog pin for the filament width sensor input
|
|
|
|
|
// Use the RAMPS 1.4 Analog input 5 on the AUX2 connector
|
|
|
|
|
#define FILWIDTH_PIN 5
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#ifdef Z_PROBE_ENDSTOP
|
|
|
|
|
#if ENABLED(Z_PROBE_ENDSTOP)
|
|
|
|
|
// Define a pin to use as the signal pin on Arduino for the Z_PROBE endstop.
|
|
|
|
|
#define Z_PROBE_PIN 32
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#ifdef FILAMENT_RUNOUT_SENSOR
|
|
|
|
|
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
|
|
|
|
// define digital pin 4 for the filament runout sensor. Use the RAMPS 1.4 digital input 4 on the servos connector
|
|
|
|
|
#define FILRUNOUT_PIN 4
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#if MB(RAMPS_13_EFF) || defined(IS_RAMPS_EFB)
|
|
|
|
|
#if MB(RAMPS_13_EFF) || ENABLED(IS_RAMPS_EFB)
|
|
|
|
|
#define FAN_PIN 9 // (Sprinter config)
|
|
|
|
|
#if MB(RAMPS_13_EFF)
|
|
|
|
|
#define CONTROLLERFAN_PIN -1 // Pin used for the fan to cool controller
|
|
|
|
|
@ -90,7 +90,7 @@
|
|
|
|
|
|
|
|
|
|
#define PS_ON_PIN 12
|
|
|
|
|
|
|
|
|
|
#if defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)
|
|
|
|
|
#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) || ENABLED(G3D_PANEL)
|
|
|
|
|
#define KILL_PIN 41
|
|
|
|
|
#else
|
|
|
|
|
#define KILL_PIN -1
|
|
|
|
|
@ -102,7 +102,7 @@
|
|
|
|
|
#define HEATER_0_PIN 10 // EXTRUDER 1
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#if MB(RAMPS_13_SF) || defined(IS_RAMPS_EFB)
|
|
|
|
|
#if MB(RAMPS_13_SF) || ENABLED(IS_RAMPS_EFB)
|
|
|
|
|
#define HEATER_1_PIN -1
|
|
|
|
|
#else
|
|
|
|
|
#define HEATER_1_PIN 9 // EXTRUDER 2 (FAN On Sprinter)
|
|
|
|
|
@ -122,7 +122,7 @@
|
|
|
|
|
|
|
|
|
|
#define TEMP_BED_PIN 14 // ANALOG NUMBERING
|
|
|
|
|
|
|
|
|
|
#ifdef NUM_SERVOS
|
|
|
|
|
#if HAS_SERVOS
|
|
|
|
|
#define SERVO0_PIN 11
|
|
|
|
|
#if NUM_SERVOS > 1
|
|
|
|
|
#define SERVO1_PIN 6
|
|
|
|
|
@ -135,15 +135,14 @@
|
|
|
|
|
#endif
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#ifdef Z_PROBE_SLED
|
|
|
|
|
#if ENABLED(Z_PROBE_SLED)
|
|
|
|
|
#define SLED_PIN -1
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#ifdef ULTRA_LCD
|
|
|
|
|
#if ENABLED(ULTRA_LCD)
|
|
|
|
|
|
|
|
|
|
#ifdef NEWPANEL
|
|
|
|
|
|
|
|
|
|
#ifdef PANEL_ONE
|
|
|
|
|
#if ENABLED(NEWPANEL)
|
|
|
|
|
#if ENABLED(PANEL_ONE)
|
|
|
|
|
#define LCD_PINS_RS 40
|
|
|
|
|
#define LCD_PINS_ENABLE 42
|
|
|
|
|
#define LCD_PINS_D4 65
|
|
|
|
|
@ -159,7 +158,7 @@
|
|
|
|
|
#define LCD_PINS_D7 29
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#ifdef REPRAP_DISCOUNT_SMART_CONTROLLER
|
|
|
|
|
#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
|
|
|
|
|
#define BEEPER 37
|
|
|
|
|
|
|
|
|
|
#define BTN_EN1 31
|
|
|
|
|
@ -167,20 +166,20 @@
|
|
|
|
|
#define BTN_ENC 35
|
|
|
|
|
|
|
|
|
|
#define SDCARDDETECT 49
|
|
|
|
|
#elif defined(LCD_I2C_PANELOLU2)
|
|
|
|
|
#elif ENABLED(LCD_I2C_PANELOLU2)
|
|
|
|
|
#define BTN_EN1 47 // reverse if the encoder turns the wrong way.
|
|
|
|
|
#define BTN_EN2 43
|
|
|
|
|
#define BTN_ENC 32
|
|
|
|
|
#define LCD_SDSS 53
|
|
|
|
|
#define SDCARDDETECT -1
|
|
|
|
|
#define KILL_PIN 41
|
|
|
|
|
#elif defined(LCD_I2C_VIKI)
|
|
|
|
|
#elif ENABLED(LCD_I2C_VIKI)
|
|
|
|
|
#define BTN_EN1 22 // reverse if the encoder turns the wrong way.
|
|
|
|
|
#define BTN_EN2 7
|
|
|
|
|
#define BTN_ENC -1
|
|
|
|
|
#define LCD_SDSS 53
|
|
|
|
|
#define SDCARDDETECT 49
|
|
|
|
|
#elif defined(ELB_FULL_GRAPHIC_CONTROLLER)
|
|
|
|
|
#elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
|
|
|
|
|
#define BTN_EN1 35 // reverse if the encoder turns the wrong way.
|
|
|
|
|
#define BTN_EN2 37
|
|
|
|
|
#define BTN_ENC 31
|
|
|
|
|
@ -217,14 +216,14 @@
|
|
|
|
|
#define BEEPER 33 // Beeper on AUX-4
|
|
|
|
|
|
|
|
|
|
// buttons are directly attached using AUX-2
|
|
|
|
|
#ifdef REPRAPWORLD_KEYPAD
|
|
|
|
|
#if ENABLED(REPRAPWORLD_KEYPAD)
|
|
|
|
|
#define BTN_EN1 64 // encoder
|
|
|
|
|
#define BTN_EN2 59 // encoder
|
|
|
|
|
#define BTN_ENC 63 // enter button
|
|
|
|
|
#define SHIFT_OUT 40 // shift register
|
|
|
|
|
#define SHIFT_CLK 44 // shift register
|
|
|
|
|
#define SHIFT_LD 42 // shift register
|
|
|
|
|
#elif defined(PANEL_ONE)
|
|
|
|
|
#elif ENABLED(PANEL_ONE)
|
|
|
|
|
#define BTN_EN1 59 // AUX2 PIN 3
|
|
|
|
|
#define BTN_EN2 63 // AUX2 PIN 4
|
|
|
|
|
#define BTN_ENC 49 // AUX3 PIN 7
|
|
|
|
|
@ -234,7 +233,7 @@
|
|
|
|
|
#define BTN_ENC 31 // the click
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#ifdef G3D_PANEL
|
|
|
|
|
#if ENABLED(G3D_PANEL)
|
|
|
|
|
#define SDCARDDETECT 49
|
|
|
|
|
#else
|
|
|
|
|
#define SDCARDDETECT -1 // Ramps does not use this port
|
|
|
|
|
@ -264,13 +263,13 @@
|
|
|
|
|
#endif // ULTRA_LCD
|
|
|
|
|
|
|
|
|
|
// SPI for Max6675 Thermocouple
|
|
|
|
|
#ifndef SDSUPPORT
|
|
|
|
|
#if DISABLED(SDSUPPORT)
|
|
|
|
|
#define MAX6675_SS 66 // Do not use pin 53 if there is even the remote possibility of using Display/SD card
|
|
|
|
|
#else
|
|
|
|
|
#define MAX6675_SS 66 // Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#ifndef SDSUPPORT
|
|
|
|
|
#if DISABLED(SDSUPPORT)
|
|
|
|
|
// these pins are defined in the SD library if building with SD support
|
|
|
|
|
#define SCK_PIN 52
|
|
|
|
|
#define MISO_PIN 50
|
|
|
|
|
|
Scott Lahteine
9 years ago
committed by