diff --git a/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h index 57fba7aa7..28217571c 100644 --- a/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h +++ b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h @@ -446,8 +446,6 @@ // and processor overload (too many expensive sqrt calls). #define DELTA_SEGMENTS_PER_SECOND 160 - // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them - // Center-to-center distance of the holes in the diagonal push rods. #define DELTA_DIAGONAL_ROD 218.0 // mm @@ -470,7 +468,6 @@ #define DELTA_PRINTABLE_RADIUS 90.0 // Delta calibration menu - // uncomment to add three points calibration menu option. // See http://minow.blogspot.com/index.html#4918805519571907051 #define DELTA_CALIBRATION_MENU @@ -670,6 +667,9 @@ * is enabled then it also applies to Z_PROBE_SPEED_SLOW. */ +// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) +//#define SOLENOID_PROBE + // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define Z_PROBE_SLED //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. @@ -728,7 +728,7 @@ #define Z_PROBE_ALLEN_KEY_DEPLOY_2_X 0.0 #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Y DELTA_PRINTABLE_RADIUS #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z 100.0 - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_SPEED/10) + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_SPEED)/10 #define Z_PROBE_ALLEN_KEY_DEPLOY_3_X Z_PROBE_ALLEN_KEY_DEPLOY_2_X * 0.75 #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Y Z_PROBE_ALLEN_KEY_DEPLOY_2_Y * 0.75 @@ -864,11 +864,11 @@ // @section machine // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. -#define INVERT_X_DIR true // DELTA does not invert +#define INVERT_X_DIR true #define INVERT_Y_DIR true #define INVERT_Z_DIR true -// Enable this option for Toshiba steppers +// Enable this option for Toshiba stepper drivers //#define CONFIG_STEPPERS_TOSHIBA // @section extruder @@ -987,6 +987,7 @@ #if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR) // Set the number of grid points per dimension. + // Works best with 5 or more points in each dimension. #define GRID_MAX_POINTS_X 9 #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X @@ -1004,7 +1005,6 @@ //#define PROBE_Y_FIRST #if ENABLED(AUTO_BED_LEVELING_BILINEAR) - // // Experimental Subdivision of the grid by Catmull-Rom method. // Synthesizes intermediate points to produce a more detailed mesh. @@ -1401,7 +1401,6 @@ // // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. // -// INDIVIDUAL_AXIS_HOMING_MENU is incompatible with DELTA kinematics. //#define INDIVIDUAL_AXIS_HOMING_MENU // diff --git a/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h index b7cc0b57c..09dd6c43e 100644 --- a/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h +++ b/Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h @@ -446,8 +446,6 @@ // and processor overload (too many expensive sqrt calls). #define DELTA_SEGMENTS_PER_SECOND 160 - // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them - // Center-to-center distance of the holes in the diagonal push rods. #define DELTA_DIAGONAL_ROD 218.0 // mm @@ -1403,7 +1401,6 @@ // // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. // -// INDIVIDUAL_AXIS_HOMING_MENU is incompatible with DELTA kinematics. //#define INDIVIDUAL_AXIS_HOMING_MENU // diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h index 2897bc3a3..c3e888cd6 100644 --- a/Marlin/example_configurations/delta/generic/Configuration.h +++ b/Marlin/example_configurations/delta/generic/Configuration.h @@ -436,8 +436,6 @@ // and processor overload (too many expensive sqrt calls). #define DELTA_SEGMENTS_PER_SECOND 200 - // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them - // Center-to-center distance of the holes in the diagonal push rods. #define DELTA_DIAGONAL_ROD 250.0 // mm @@ -701,7 +699,6 @@ // Use double touch for probing //#define PROBE_DOUBLE_TOUCH - /** * Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe * Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN. diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h index 7d69dcc07..401f7b5cb 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h @@ -436,8 +436,6 @@ // and processor overload (too many expensive sqrt calls). #define DELTA_SEGMENTS_PER_SECOND 200 - // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them - // Center-to-center distance of the holes in the diagonal push rods. #define DELTA_DIAGONAL_ROD 215.0 // mm diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h index 8b809300e..419f47ca4 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h @@ -423,8 +423,6 @@ // and processor overload (too many expensive sqrt calls). #define DELTA_SEGMENTS_PER_SECOND 160 - // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them - // Center-to-center distance of the holes in the diagonal push rods. #define DELTA_DIAGONAL_ROD 301.0 // mm diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration.h b/Marlin/example_configurations/delta/kossel_xl/Configuration.h index b9bd403b9..320e19bb1 100644 --- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h @@ -441,8 +441,6 @@ // and processor overload (too many expensive sqrt calls). #define DELTA_SEGMENTS_PER_SECOND 160 - // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them - // Center-to-center distance of the holes in the diagonal push rods. #define DELTA_DIAGONAL_ROD 317.3 + 2.5 // mm diff --git a/Marlin/ultralcd.cpp b/Marlin/ultralcd.cpp index f15801e7c..bca731ddb 100755 --- a/Marlin/ultralcd.cpp +++ b/Marlin/ultralcd.cpp @@ -194,7 +194,7 @@ uint16_t max_display_update_time = 0; DECLARE_MENU_EDIT_TYPE(float, float52); DECLARE_MENU_EDIT_TYPE(float, float62); DECLARE_MENU_EDIT_TYPE(unsigned long, long5); - + void menu_action_setting_edit_bool(const char* pstr, bool* ptr); void menu_action_setting_edit_callback_bool(const char* pstr, bool* ptr, screenFunc_t callbackFunc); void menu_action_setting_edit_accessor_bool(const char* pstr, bool (*pget)(), void (*pset)(bool)); diff --git a/buildroot/share/cmake/CMakeLists.txt b/buildroot/share/cmake/CMakeLists.txt index f7a8deb55..54cef29cc 100644 --- a/buildroot/share/cmake/CMakeLists.txt +++ b/buildroot/share/cmake/CMakeLists.txt @@ -14,7 +14,7 @@ cmake_minimum_required(VERSION 2.8) # cmake -G"Unix Makefiles" .. # # make # #====================================================================# - + #====================================================================# # Download marlin-cmake scriptfiles if not already installed # # and add the path to the module path # @@ -26,13 +26,13 @@ if(NOT EXISTS ${CMAKE_CURRENT_LIST_DIR}/marlin-cmake) file(DOWNLOAD https://github.com/tohara/marlin-cmake/archive/${SCRIPT_BRANCH}.tar.gz ${CMAKE_CURRENT_LIST_DIR}/marlin-cmake-src.tar.gz SHOW_PROGRESS) - + execute_process(COMMAND ${CMAKE_COMMAND} -E tar -xvf ${CMAKE_CURRENT_LIST_DIR}/marlin-cmake-src.tar.gz WORKING_DIRECTORY ${CMAKE_CURRENT_LIST_DIR}) - + file(RENAME ${CMAKE_CURRENT_LIST_DIR}/marlin-cmake-${SCRIPT_BRANCH} ${CMAKE_CURRENT_LIST_DIR}/marlin-cmake) file(REMOVE ${CMAKE_CURRENT_LIST_DIR}/marlin-cmake-src.tar.gz) - - + + endif() if(WIN32 AND NOT EXISTS ${CMAKE_BINARY_DIR}/make.exe) diff --git a/buildroot/share/scripts/MarlinMesh.scad b/buildroot/share/scripts/MarlinMesh.scad index 68e0eee66..7616ded69 100644 --- a/buildroot/share/scripts/MarlinMesh.scad +++ b/buildroot/share/scripts/MarlinMesh.scad @@ -115,7 +115,7 @@ module point_markers(show_home=true) { $fn=8; rotate([90,0]) text(str(z), 6, label_font_lg, halign="center", valign="center"); - + translate([0,0,down?-6:6]) rotate([90,0]) text(str(down ? "" : "+", v), 3, label_font_sm, halign="center", valign="center"); } diff --git a/buildroot/share/scripts/createSpeedLookupTable.py b/buildroot/share/scripts/createSpeedLookupTable.py index 13ed92d52..ade28ee33 100755 --- a/buildroot/share/scripts/createSpeedLookupTable.py +++ b/buildroot/share/scripts/createSpeedLookupTable.py @@ -30,7 +30,7 @@ for i in range(32): print " ", for j in range(8): print "{%d, %d}," % (a[8*i+j], b[8*i+j]), - print + print print "};" print @@ -42,7 +42,7 @@ for i in range(32): print " ", for j in range(8): print "{%d, %d}," % (a[8*i+j], b[8*i+j]), - print + print print "};" print