Merge pull request #1722 from Natealus/Development

Azteeg X3 Pro Pin Revisions
master
Scott Lahteine 10 years ago
commit cc7a081cae

@ -5,9 +5,35 @@
#include "pins_RAMPS_13.h" #include "pins_RAMPS_13.h"
#undef FAN_PIN #undef FAN_PIN
#define FAN_PIN 9 // (Sprinter config) #define FAN_PIN 6 //Part Cooling System
#define BEEPER 33 #define BEEPER 33
#define CONTROLLERFAN_PIN 4 //Pin used for the fan to cool motherboard (-1 to disable)
//Fans/Water Pump to cool the hotend cool side.
#define EXTRUDER_0_AUTO_FAN_PIN 5
#define EXTRUDER_1_AUTO_FAN_PIN 5
#define EXTRUDER_2_AUTO_FAN_PIN 5
#define EXTRUDER_3_AUTO_FAN_PIN 5
//
//This section is to swap the MIN and MAX pins because the X3 Pro comes with only
//MIN endstops soldered onto the board. Delta code wants the homing endstops to be
//the MAX so I swapped them here. Comment them out with // if you want them original.
//Note: I had to solder on the additional MAX Endstop pins to attach a Z-Probe
//endstop switch.
//
#undef X_MIN_PIN
#undef X_MAX_PIN
#undef Y_MIN_PIN
#undef Y_MAX_PIN
#undef Z_MIN_PIN
#undef Z_MAX_PIN
#define X_MIN_PIN 2
#define X_MAX_PIN 3
#define Y_MIN_PIN 15
#define Y_MAX_PIN 14
#define Z_MIN_PIN 19
#define Z_MAX_PIN 18
//
#define E2_STEP_PIN 23 #define E2_STEP_PIN 23
#define E2_DIR_PIN 25 #define E2_DIR_PIN 25
@ -24,7 +50,7 @@
#undef HEATER_1_PIN #undef HEATER_1_PIN
#undef HEATER_2_PIN #undef HEATER_2_PIN
#undef HEATER_3_PIN #undef HEATER_3_PIN
#define HEATER_1_PIN -1 #define HEATER_1_PIN 9
#define HEATER_2_PIN 16 #define HEATER_2_PIN 16
#define HEATER_3_PIN 17 #define HEATER_3_PIN 17
#define HEATER_4_PIN 4 #define HEATER_4_PIN 4
@ -39,3 +65,26 @@
#define TEMP_4_PIN 10 // ANALOG NUMBERING #define TEMP_4_PIN 10 // ANALOG NUMBERING
#define TC1 4 // ANALOG NUMBERING Thermo couple on Azteeg X3Pro #define TC1 4 // ANALOG NUMBERING Thermo couple on Azteeg X3Pro
#define TC2 5 // ANALOG NUMBERING Thermo couple on Azteeg X3Pro #define TC2 5 // ANALOG NUMBERING Thermo couple on Azteeg X3Pro
//
//These Servo pins are for when they are defined. Tested for usage with bed leveling
//on a Delta with 1 servo. Running through the Z servo endstop in code.
//Physical wire attachment was done on EXT1 on the GND, 5V, and D47 pins.
//
#undef SERVO0_PIN
#undef SERVO1_PIN
#undef SERVO2_PIN
#undef SERVO3_PIN
#ifdef NUM_SERVOS
#define SERVO0_PIN -1
#if NUM_SERVOS > 1
#define SERVO1_PIN -1
#if NUM_SERVOS > 2
#define SERVO2_PIN 47
#if NUM_SERVOS > 3
#define SERVO3_PIN -1
#endif
#endif
#endif
#endif

Loading…
Cancel
Save