diff --git a/Marlin/Conditionals.h b/Marlin/Conditionals.h index 7ec8fe571..54b111bb6 100644 --- a/Marlin/Conditionals.h +++ b/Marlin/Conditionals.h @@ -535,6 +535,21 @@ #define HAS_PID_HEATING (ENABLED(PIDTEMP) || ENABLED(PIDTEMPBED)) #define HAS_PID_FOR_BOTH (ENABLED(PIDTEMP) && ENABLED(PIDTEMPBED)) + /** + * SINGLENOZZLE needs to differentiate EXTRUDERS and HOTENDS + * And all "extruders" are in the same place. + */ + #if ENABLED(SINGLENOZZLE) + #define HOTENDS 1 + #undef TEMP_SENSOR_1_AS_REDUNDANT + #undef HOTEND_OFFSET_X + #undef HOTEND_OFFSET_Y + #define HOTEND_OFFSET_X { 0 } + #define HOTEND_OFFSET_Y { 0 } + #else + #define HOTENDS EXTRUDERS + #endif + /** * ARRAY_BY_EXTRUDERS based on EXTRUDERS */ @@ -551,15 +566,20 @@ #define ARRAY_BY_EXTRUDERS1(v1) ARRAY_BY_EXTRUDERS(v1, v1, v1, v1) /** - * With SINGLENOZZLE all "extruders" are in the same place + * ARRAY_BY_HOTENDS based on HOTENDS */ - #if ENABLED(SINGLENOZZLE) - #undef EXTRUDER_OFFSET_X - #undef EXTRUDER_OFFSET_Y - #define EXTRUDER_OFFSET_X { 0 } - #define EXTRUDER_OFFSET_Y { 0 } + #if HOTENDS > 3 + #define ARRAY_BY_HOTENDS(v1, v2, v3, v4) { v1, v2, v3, v4 } + #elif HOTENDS > 2 + #define ARRAY_BY_HOTENDS(v1, v2, v3, v4) { v1, v2, v3 } + #elif HOTENDS > 1 + #define ARRAY_BY_HOTENDS(v1, v2, v3, v4) { v1, v2 } + #else + #define ARRAY_BY_HOTENDS(v1, v2, v3, v4) { v1 } #endif + #define ARRAY_BY_HOTENDS1(v1) ARRAY_BY_HOTENDS(v1, v1, v1, v1) + /** * Z_DUAL_ENDSTOPS endstop reassignment */ @@ -695,11 +715,11 @@ * Helper Macros for heaters and extruder fan */ #define WRITE_HEATER_0P(v) WRITE(HEATER_0_PIN, v) - #if EXTRUDERS > 1 || ENABLED(HEATERS_PARALLEL) + #if HOTENDS > 1 || ENABLED(HEATERS_PARALLEL) #define WRITE_HEATER_1(v) WRITE(HEATER_1_PIN, v) - #if EXTRUDERS > 2 + #if HOTENDS > 2 #define WRITE_HEATER_2(v) WRITE(HEATER_2_PIN, v) - #if EXTRUDERS > 3 + #if HOTENDS > 3 #define WRITE_HEATER_3(v) WRITE(HEATER_3_PIN, v) #endif #endif diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 968fca659..4c1727102 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -126,8 +126,8 @@ // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. -//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis -//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX @@ -224,8 +224,8 @@ #define BED_MAXTEMP 150 // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS -//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=U^2/R -//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R +//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R //=========================================================================== //============================= PID Settings ================================ @@ -241,8 +241,8 @@ //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay - //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) - // Set/get with gcode: M301 E[extruder number, 0-2] + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index 61cdef140..952da0fa7 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -237,7 +237,7 @@ #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position - // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops // without modifying the firmware (through the "M218 T1 X???" command). // Remember: you should set the second extruder x-offset to 0 in your slicer. diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp index d109055e7..9e40335c0 100644 --- a/Marlin/Marlin_main.cpp +++ b/Marlin/Marlin_main.cpp @@ -356,16 +356,16 @@ static uint8_t target_extruder; #endif // Extruder offsets -#if EXTRUDERS > 1 - #ifndef EXTRUDER_OFFSET_X - #define EXTRUDER_OFFSET_X { 0 } // X offsets for each extruder +#if HOTENDS > 1 + #ifndef HOTEND_OFFSET_X + #define HOTEND_OFFSET_X { 0 } // X offsets for each extruder #endif - #ifndef EXTRUDER_OFFSET_Y - #define EXTRUDER_OFFSET_Y { 0 } // Y offsets for each extruder + #ifndef HOTEND_OFFSET_Y + #define HOTEND_OFFSET_Y { 0 } // Y offsets for each extruder #endif - float extruder_offset[][EXTRUDERS] = { - EXTRUDER_OFFSET_X, - EXTRUDER_OFFSET_Y + float hotend_offset[][HOTENDS] = { + HOTEND_OFFSET_X, + HOTEND_OFFSET_Y #if ENABLED(DUAL_X_CARRIAGE) , { 0 } // Z offsets for each extruder #endif @@ -1249,7 +1249,7 @@ XYZ_CONSTS_FROM_CONFIG(signed char, home_dir, HOME_DIR); * This allow soft recalibration of the second extruder offset position * without firmware reflash (through the M218 command). */ - return (extruder_offset[X_AXIS][1] > 0) ? extruder_offset[X_AXIS][1] : X2_HOME_POS; + return (hotend_offset[X_AXIS][1] > 0) ? hotend_offset[X_AXIS][1] : X2_HOME_POS; } static int x_home_dir(int extruder) { @@ -1280,7 +1280,7 @@ static void update_software_endstops(AxisEnum axis) { #if ENABLED(DUAL_X_CARRIAGE) if (axis == X_AXIS) { - float dual_max_x = max(extruder_offset[X_AXIS][1], X2_MAX_POS); + float dual_max_x = max(hotend_offset[X_AXIS][1], X2_MAX_POS); if (active_extruder != 0) { sw_endstop_min[X_AXIS] = X2_MIN_POS + offs; sw_endstop_max[X_AXIS] = dual_max_x + offs; @@ -4407,8 +4407,8 @@ inline void gcode_M104() { SERIAL_PROTOCOLPGM(" /"); SERIAL_PROTOCOL_F(thermalManager.degTargetBed(), 1); #endif - #if EXTRUDERS > 1 - for (int8_t e = 0; e < EXTRUDERS; ++e) { + #if HOTENDS > 1 + for (int8_t e = 0; e < HOTENDS; ++e) { SERIAL_PROTOCOLPGM(" T"); SERIAL_PROTOCOL(e); SERIAL_PROTOCOLCHAR(':'); @@ -4433,8 +4433,8 @@ inline void gcode_M104() { #else SERIAL_PROTOCOL(thermalManager.getHeaterPower(target_extruder)); #endif - #if EXTRUDERS > 1 - for (int8_t e = 0; e < EXTRUDERS; ++e) { + #if HOTENDS > 1 + for (int8_t e = 0; e < HOTENDS; ++e) { SERIAL_PROTOCOLPGM(" @"); SERIAL_PROTOCOL(e); SERIAL_PROTOCOLCHAR(':'); @@ -4453,13 +4453,13 @@ inline void gcode_M104() { SERIAL_PROTOCOLPGM("C->"); SERIAL_PROTOCOL_F(thermalManager.rawBedTemp() / OVERSAMPLENR, 0); #endif - for (int8_t cur_extruder = 0; cur_extruder < EXTRUDERS; ++cur_extruder) { + for (int8_t cur_hotend = 0; cur_hotend < HOTENDS; ++cur_hotend) { SERIAL_PROTOCOLPGM(" T"); - SERIAL_PROTOCOL(cur_extruder); + SERIAL_PROTOCOL(cur_hotend); SERIAL_PROTOCOLCHAR(':'); - SERIAL_PROTOCOL_F(thermalManager.degHotend(cur_extruder), 1); + SERIAL_PROTOCOL_F(thermalManager.degHotend(cur_hotend), 1); SERIAL_PROTOCOLPGM("C->"); - SERIAL_PROTOCOL_F(thermalManager.rawHotendTemp(cur_extruder) / OVERSAMPLENR, 0); + SERIAL_PROTOCOL_F(thermalManager.rawHotendTemp(cur_hotend) / OVERSAMPLENR, 0); } #endif } @@ -5391,7 +5391,7 @@ inline void gcode_M206() { #endif // FWRETRACT -#if EXTRUDERS > 1 +#if HOTENDS > 1 /** * M218 - set hotend offset (in mm) @@ -5404,29 +5404,29 @@ inline void gcode_M206() { inline void gcode_M218() { if (get_target_extruder_from_command(218)) return; - if (code_seen('X')) extruder_offset[X_AXIS][target_extruder] = code_value(); - if (code_seen('Y')) extruder_offset[Y_AXIS][target_extruder] = code_value(); + if (code_seen('X')) hotend_offset[X_AXIS][target_extruder] = code_value(); + if (code_seen('Y')) hotend_offset[Y_AXIS][target_extruder] = code_value(); #if ENABLED(DUAL_X_CARRIAGE) - if (code_seen('Z')) extruder_offset[Z_AXIS][target_extruder] = code_value(); + if (code_seen('Z')) hotend_offset[Z_AXIS][target_extruder] = code_value(); #endif SERIAL_ECHO_START; SERIAL_ECHOPGM(MSG_HOTEND_OFFSET); - for (int e = 0; e < EXTRUDERS; e++) { + for (int e = 0; e < HOTENDS; e++) { SERIAL_CHAR(' '); - SERIAL_ECHO(extruder_offset[X_AXIS][e]); + SERIAL_ECHO(hotend_offset[X_AXIS][e]); SERIAL_CHAR(','); - SERIAL_ECHO(extruder_offset[Y_AXIS][e]); + SERIAL_ECHO(hotend_offset[Y_AXIS][e]); #if ENABLED(DUAL_X_CARRIAGE) SERIAL_CHAR(','); - SERIAL_ECHO(extruder_offset[Z_AXIS][e]); + SERIAL_ECHO(hotend_offset[Z_AXIS][e]); #endif } SERIAL_EOL; } -#endif // EXTRUDERS > 1 +#endif // HOTENDS > 1 /** * M220: Set speed percentage factor, aka "Feed Rate" (M220 S95) @@ -5556,7 +5556,7 @@ inline void gcode_M226() { // default behaviour (omitting E parameter) is to update for extruder 0 only int e = code_seen('E') ? code_value() : 0; // extruder being updated - if (e < EXTRUDERS) { // catch bad input value + if (e < HOTENDS) { // catch bad input value if (code_seen('P')) PID_PARAM(Kp, e) = code_value(); if (code_seen('I')) PID_PARAM(Ki, e) = scalePID_i(code_value()); if (code_seen('D')) PID_PARAM(Kd, e) = scalePID_d(code_value()); @@ -5568,10 +5568,10 @@ inline void gcode_M226() { thermalManager.updatePID(); SERIAL_ECHO_START; - #if ENABLED(PID_PARAMS_PER_EXTRUDER) + #if ENABLED(PID_PARAMS_PER_HOTEND) SERIAL_ECHO(" e:"); // specify extruder in serial output SERIAL_ECHO(e); - #endif // PID_PARAMS_PER_EXTRUDER + #endif // PID_PARAMS_PER_HOTEND SERIAL_ECHO(" p:"); SERIAL_ECHO(PID_PARAM(Kp, e)); SERIAL_ECHO(" i:"); @@ -5690,7 +5690,7 @@ inline void gcode_M303() { float temp = code_seen('S') ? code_value() : (e < 0 ? 70.0 : 150.0); - if (e >= 0 && e < EXTRUDERS) + if (e >= 0 && e < HOTENDS) target_extruder = e; KEEPALIVE_STATE(NOT_BUSY); // don't send "busy: processing" messages during autotune output @@ -6272,13 +6272,13 @@ inline void gcode_M503() { SERIAL_ECHO_START; SERIAL_ECHOPGM(MSG_HOTEND_OFFSET); SERIAL_CHAR(' '); - SERIAL_ECHO(extruder_offset[X_AXIS][0]); + SERIAL_ECHO(hotend_offset[X_AXIS][0]); SERIAL_CHAR(','); - SERIAL_ECHO(extruder_offset[Y_AXIS][0]); + SERIAL_ECHO(hotend_offset[Y_AXIS][0]); SERIAL_CHAR(' '); SERIAL_ECHO(duplicate_extruder_x_offset); SERIAL_CHAR(','); - SERIAL_ECHOLN(extruder_offset[Y_AXIS][1]); + SERIAL_ECHOLN(hotend_offset[Y_AXIS][1]); break; case DXC_FULL_CONTROL_MODE: case DXC_AUTO_PARK_MODE: @@ -6436,7 +6436,7 @@ inline void gcode_T(uint8_t tmp_extruder) { #endif } - #if EXTRUDERS > 1 + #if HOTENDS > 1 if (tmp_extruder != active_extruder) { // Save current position to return to after applying extruder offset set_destination_to_current(); @@ -6454,8 +6454,8 @@ inline void gcode_T(uint8_t tmp_extruder) { } // apply Y & Z extruder offset (x offset is already used in determining home pos) - current_position[Y_AXIS] -= extruder_offset[Y_AXIS][active_extruder] - extruder_offset[Y_AXIS][tmp_extruder]; - current_position[Z_AXIS] -= extruder_offset[Z_AXIS][active_extruder] - extruder_offset[Z_AXIS][tmp_extruder]; + current_position[Y_AXIS] -= hotend_offset[Y_AXIS][active_extruder] - hotend_offset[Y_AXIS][tmp_extruder]; + current_position[Z_AXIS] -= hotend_offset[Z_AXIS][active_extruder] - hotend_offset[Z_AXIS][tmp_extruder]; active_extruder = tmp_extruder; // This function resets the max/min values - the current position may be overwritten below. @@ -6485,11 +6485,11 @@ inline void gcode_T(uint8_t tmp_extruder) { #else // !DUAL_X_CARRIAGE #if ENABLED(AUTO_BED_LEVELING_FEATURE) // Offset extruder, make sure to apply the bed level rotation matrix - vector_3 tmp_offset_vec = vector_3(extruder_offset[X_AXIS][tmp_extruder], - extruder_offset[Y_AXIS][tmp_extruder], + vector_3 tmp_offset_vec = vector_3(hotend_offset[X_AXIS][tmp_extruder], + hotend_offset[Y_AXIS][tmp_extruder], 0), - act_offset_vec = vector_3(extruder_offset[X_AXIS][active_extruder], - extruder_offset[Y_AXIS][active_extruder], + act_offset_vec = vector_3(hotend_offset[X_AXIS][active_extruder], + hotend_offset[Y_AXIS][active_extruder], 0), offset_vec = tmp_offset_vec - act_offset_vec; @@ -6521,7 +6521,7 @@ inline void gcode_T(uint8_t tmp_extruder) { // The newly-selected extruder is actually at... for (int i=X_AXIS; i<=Y_AXIS; i++) { - float diff = extruder_offset[i][tmp_extruder] - extruder_offset[i][active_extruder]; + float diff = hotend_offset[i][tmp_extruder] - hotend_offset[i][active_extruder]; current_position[i] += diff; position_shift[i] += diff; // Offset the coordinate space update_software_endstops((AxisEnum)i); @@ -6552,7 +6552,7 @@ inline void gcode_T(uint8_t tmp_extruder) { enable_solenoid_on_active_extruder(); #endif // EXT_SOLENOID - #endif // EXTRUDERS > 1 + #endif // HOTENDS > 1 feedrate = stored_feedrate; @@ -6983,7 +6983,7 @@ void process_next_command() { break; #endif // FWRETRACT - #if EXTRUDERS > 1 + #if HOTENDS > 1 case 218: // M218 - set hotend offset (in mm), T X Y gcode_M218(); break; @@ -7853,8 +7853,8 @@ void prepare_move() { float max_temp = 0.0; if (ELAPSED(millis(), next_status_led_update_ms)) { next_status_led_update_ms += 500; // Update every 0.5s - for (int8_t cur_extruder = 0; cur_extruder < EXTRUDERS; ++cur_extruder) - max_temp = max(max(max_temp, thermalManager.degHotend(cur_extruder)), thermalManager.degTargetHotend(cur_extruder)); + for (int8_t cur_hotend = 0; cur_hotend < HOTENDS; ++cur_hotend) + max_temp = max(max(max_temp, thermalManager.degHotend(cur_hotend)), thermalManager.degTargetHotend(cur_hotend)); #if HAS_TEMP_BED max_temp = max(max(max_temp, thermalManager.degTargetBed()), thermalManager.degBed()); #endif diff --git a/Marlin/SanityCheck.h b/Marlin/SanityCheck.h index 19edb7598..a913cb1b0 100644 --- a/Marlin/SanityCheck.h +++ b/Marlin/SanityCheck.h @@ -468,39 +468,45 @@ /** * Test Heater, Temp Sensor, and Extruder Pins; Sensor Type must also be set. */ -#if EXTRUDERS > 3 - #if TEMP_SENSOR_3 == 0 - #error "TEMP_SENSOR_3 is required with 4 EXTRUDERS." - #elif !HAS_HEATER_3 - #error "HEATER_3_PIN not defined for this board." - #elif !PIN_EXISTS(TEMP_3) - #error "TEMP_3_PIN not defined for this board." - #elif !PIN_EXISTS(E3_STEP) || !PIN_EXISTS(E3_DIR) || !PIN_EXISTS(E3_ENABLE) - #error "E3_STEP_PIN, E3_DIR_PIN, or E3_ENABLE_PIN not defined for this board." - #endif -#elif EXTRUDERS > 2 - #if TEMP_SENSOR_2 == 0 - #error "TEMP_SENSOR_2 is required with 3 or more EXTRUDERS." - #elif !HAS_HEATER_2 - #error "HEATER_2_PIN not defined for this board." - #elif !PIN_EXISTS(TEMP_2) - #error "TEMP_2_PIN not defined for this board." - #elif !PIN_EXISTS(E2_STEP) || !PIN_EXISTS(E2_DIR) || !PIN_EXISTS(E2_ENABLE) - #error "E2_STEP_PIN, E2_DIR_PIN, or E2_ENABLE_PIN not defined for this board." +#if !HAS_HEATER_0 + #error "HEATER_0_PIN not defined for this board." +#elif !PIN_EXISTS(TEMP_0) + #error "TEMP_0_PIN not defined for this board." +#elif !PIN_EXISTS(E0_STEP) || !PIN_EXISTS(E0_DIR) || !PIN_EXISTS(E0_ENABLE) + #error "E0_STEP_PIN, E0_DIR_PIN, or E0_ENABLE_PIN not defined for this board." +#elif TEMP_SENSOR_0 == 0 + #error "TEMP_SENSOR_0 is required." +#endif + +#if HOTENDS > 1 || ENABLED(HEATERS_PARALLEL) + #if !HAS_HEATER_1 + #error "HEATER_1_PIN not defined for this board." #endif -#elif EXTRUDERS > 1 +#endif + +#if HOTENDS > 1 #if TEMP_SENSOR_1 == 0 - #error "TEMP_SENSOR_1 is required with 2 or more EXTRUDERS." + #error "TEMP_SENSOR_1 is required with 2 or more HOTENDS." #elif !PIN_EXISTS(TEMP_1) #error "TEMP_1_PIN not defined for this board." - #elif !PIN_EXISTS(E1_STEP) || !PIN_EXISTS(E1_DIR) || !PIN_EXISTS(E1_ENABLE) - #error "E1_STEP_PIN, E1_DIR_PIN, or E1_ENABLE_PIN not defined for this board." #endif -#endif - -#if EXTRUDERS > 1 || ENABLED(HEATERS_PARALLEL) - #if !HAS_HEATER_1 - #error "HEATER_1_PIN not defined for this board." + #if HOTENDS > 2 + #if TEMP_SENSOR_2 == 0 + #error "TEMP_SENSOR_2 is required with 3 or more HOTENDS." + #elif !HAS_HEATER_2 + #error "HEATER_2_PIN not defined for this board." + #elif !PIN_EXISTS(TEMP_2) + #error "TEMP_2_PIN not defined for this board." + #endif + #if HOTENDS > 3 + #if TEMP_SENSOR_3 == 0 + #error "TEMP_SENSOR_3 is required with 4 HOTENDS." + #elif !HAS_HEATER_3 + #error "HEATER_3_PIN not defined for this board." + #elif !PIN_EXISTS(TEMP_3) + #error "TEMP_3_PIN not defined for this board." + #endif + #endif #endif #endif @@ -508,14 +514,21 @@ #error "TEMP_SENSOR_1 is required with TEMP_SENSOR_1_AS_REDUNDANT." #endif -#if !HAS_HEATER_0 - #error "HEATER_0_PIN not defined for this board." -#elif !PIN_EXISTS(TEMP_0) - #error "TEMP_0_PIN not defined for this board." -#elif !PIN_EXISTS(E0_STEP) || !PIN_EXISTS(E0_DIR) || !PIN_EXISTS(E0_ENABLE) - #error "E0_STEP_PIN, E0_DIR_PIN, or E0_ENABLE_PIN not defined for this board." -#elif TEMP_SENSOR_0 == 0 - #error "TEMP_SENSOR_0 is required." +/** + * Test Extruder Pins + */ +#if EXTRUDERS > 3 + #if !PIN_EXISTS(E3_STEP) || !PIN_EXISTS(E3_DIR) || !PIN_EXISTS(E3_ENABLE) + #error E3_STEP_PIN, E3_DIR_PIN, or E3_ENABLE_PIN not defined for this board. + #endif +#elif EXTRUDERS > 2 + #if !PIN_EXISTS(E2_STEP) || !PIN_EXISTS(E2_DIR) || !PIN_EXISTS(E2_ENABLE) + #error E2_STEP_PIN, E2_DIR_PIN, or E2_ENABLE_PIN not defined for this board. + #endif +#elif EXTRUDERS > 1 + #if !PIN_EXISTS(E1_STEP) || !PIN_EXISTS(E1_DIR) || !PIN_EXISTS(E1_ENABLE) + #error E1_STEP_PIN, E1_DIR_PIN, or E1_ENABLE_PIN not defined for this board. + #endif #endif /** @@ -574,6 +587,12 @@ #error "Z_DUAL_ENDSTOPS settings are simplified. Just set Z2_USE_ENDSTOP to the endstop you want to repurpose for Z2" #elif defined(LANGUAGE_INCLUDE) #error "LANGUAGE_INCLUDE has been replaced by LCD_LANGUAGE. Please update your configuration." +#elif defined(EXTRUDER_OFFSET_X) || defined(EXTRUDER_OFFSET_Y) + #error "EXTRUDER_OFFSET_[XY] is deprecated. Use HOTEND_OFFSET_[XY] instead." +#elif defined(PID_PARAMS_PER_EXTRUDER) + #error "PID_PARAMS_PER_EXTRUDER is deprecated. Use PID_PARAMS_PER_HOTEND instead." +#elif defined(EXTRUDER_WATTS) + #error "EXTRUDER_WATTS is deprecated. Use HOTEND_WATTS instead." #endif #endif //SANITYCHECK_H diff --git a/Marlin/boards.h b/Marlin/boards.h index b06534c98..3602e6e87 100644 --- a/Marlin/boards.h +++ b/Marlin/boards.h @@ -32,17 +32,17 @@ #define BOARD_CHEAPTRONIC 2 // Cheaptronic v1.0 #define BOARD_SETHI 20 // Sethi 3D_1 #define BOARD_RAMPS_OLD 3 // MEGA/RAMPS up to 1.2 -#define BOARD_RAMPS_13_EFB 33 // RAMPS 1.3 (Power outputs: Extruder, Fan, Bed) -#define BOARD_RAMPS_13_EEB 34 // RAMPS 1.3 (Power outputs: Extruder0, Extruder1, Bed) -#define BOARD_RAMPS_13_EFF 35 // RAMPS 1.3 (Power outputs: Extruder, Fan, Fan) -#define BOARD_RAMPS_13_EEF 36 // RAMPS 1.3 (Power outputs: Extruder0, Extruder1, Fan) +#define BOARD_RAMPS_13_EFB 33 // RAMPS 1.3 (Power outputs: Hotend, Fan, Bed) +#define BOARD_RAMPS_13_EEB 34 // RAMPS 1.3 (Power outputs: Hotend0, Hotend1, Bed) +#define BOARD_RAMPS_13_EFF 35 // RAMPS 1.3 (Power outputs: Hotend, Fan0, Fan1) +#define BOARD_RAMPS_13_EEF 36 // RAMPS 1.3 (Power outputs: Hotend0, Hotend1, Fan) #define BOARD_RAMPS_13_SF 38 // RAMPS 1.3 (Power outputs: Spindle, Controller Fan) #define BOARD_FELIX2 37 // Felix 2.0+ Electronics Board (RAMPS like) #define BOARD_RIGIDBOARD 42 // Invent-A-Part RigidBoard -#define BOARD_RAMPS_14_EFB 43 // RAMPS 1.4 (Power outputs: Extruder, Fan, Bed) -#define BOARD_RAMPS_14_EEB 44 // RAMPS 1.4 (Power outputs: Extruder0, Extruder1, Bed) -#define BOARD_RAMPS_14_EFF 45 // RAMPS 1.4 (Power outputs: Extruder, Fan, Fan) -#define BOARD_RAMPS_14_EEF 46 // RAMPS 1.4 (Power outputs: Extruder0, Extruder1, Fan) +#define BOARD_RAMPS_14_EFB 43 // RAMPS 1.4 (Power outputs: Hotend, Fan, Bed) +#define BOARD_RAMPS_14_EEB 44 // RAMPS 1.4 (Power outputs: Hotend0, Hotend1, Bed) +#define BOARD_RAMPS_14_EFF 45 // RAMPS 1.4 (Power outputs: Hotend, Fan0, Fan1) +#define BOARD_RAMPS_14_EEF 46 // RAMPS 1.4 (Power outputs: Hotend0, Hotend1, Fan) #define BOARD_RAMPS_14_SF 48 // RAMPS 1.4 (Power outputs: Spindle, Controller Fan) #define BOARD_GEN6 5 // Gen6 #define BOARD_GEN6_DELUXE 51 // Gen6 deluxe diff --git a/Marlin/configuration_store.cpp b/Marlin/configuration_store.cpp index 001955f6e..755ef9508 100644 --- a/Marlin/configuration_store.cpp +++ b/Marlin/configuration_store.cpp @@ -246,7 +246,7 @@ void Config_StoreSettings() { for (uint8_t e = 0; e < 4; e++) { #if ENABLED(PIDTEMP) - if (e < EXTRUDERS) { + if (e < HOTENDS) { EEPROM_WRITE_VAR(i, PID_PARAM(Kp, e)); EEPROM_WRITE_VAR(i, PID_PARAM(Ki, e)); EEPROM_WRITE_VAR(i, PID_PARAM(Kd, e)); @@ -266,7 +266,7 @@ void Config_StoreSettings() { for (uint8_t q = 3; q--;) EEPROM_WRITE_VAR(i, dummy); // Ki, Kd, Kc } - } // Extruders Loop + } // Hotends Loop #if DISABLED(PID_ADD_EXTRUSION_RATE) int lpq_len = 20; @@ -426,7 +426,7 @@ void Config_RetrieveSettings() { #if ENABLED(PIDTEMP) for (uint8_t e = 0; e < 4; e++) { // 4 = max extruders currently supported by Marlin EEPROM_READ_VAR(i, dummy); // Kp - if (e < EXTRUDERS && dummy != DUMMY_PID_VALUE) { + if (e < HOTENDS && dummy != DUMMY_PID_VALUE) { // do not need to scale PID values as the values in EEPROM are already scaled PID_PARAM(Kp, e) = dummy; EEPROM_READ_VAR(i, PID_PARAM(Ki, e)); @@ -584,8 +584,8 @@ void Config_ResetDefault() { #endif #if ENABLED(PIDTEMP) - #if ENABLED(PID_PARAMS_PER_EXTRUDER) - for (uint8_t e = 0; e < EXTRUDERS; e++) + #if ENABLED(PID_PARAMS_PER_HOTEND) + for (uint8_t e = 0; e < HOTENDS; e++) #else int e = 0; UNUSED(e); // only need to write once #endif @@ -801,9 +801,9 @@ void Config_PrintSettings(bool forReplay) { SERIAL_ECHOLNPGM("PID settings:"); } #if ENABLED(PIDTEMP) - #if EXTRUDERS > 1 + #if HOTENDS > 1 if (forReplay) { - for (uint8_t i = 0; i < EXTRUDERS; i++) { + for (uint8_t i = 0; i < HOTENDS; i++) { CONFIG_ECHO_START; SERIAL_ECHOPAIR(" M301 E", i); SERIAL_ECHOPAIR(" P", PID_PARAM(Kp, i)); @@ -817,8 +817,8 @@ void Config_PrintSettings(bool forReplay) { } } else - #endif // EXTRUDERS > 1 - // !forReplay || EXTRUDERS == 1 + #endif // HOTENDS > 1 + // !forReplay || HOTENDS == 1 { CONFIG_ECHO_START; SERIAL_ECHOPAIR(" M301 P", PID_PARAM(Kp, 0)); // for compatibility with hosts, only echo values for E0 diff --git a/Marlin/dogm_bitmaps.h b/Marlin/dogm_bitmaps.h index 546cfd6f0..6b6541bb3 100644 --- a/Marlin/dogm_bitmaps.h +++ b/Marlin/dogm_bitmaps.h @@ -110,7 +110,7 @@ // be displayed. #if HAS_TEMP_BED - #if EXTRUDERS == 1 + #if HOTENDS == 1 #define STATUS_SCREENWIDTH 115 //Width in pixels #define STATUS_SCREENHEIGHT 19 //Height in pixels #define STATUS_SCREENBYTEWIDTH 15 //Width in bytes @@ -160,7 +160,7 @@ 0x1E, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01, 0xFF, 0xFF, 0x80, 0x7F, 0xFF, 0xE0, 0x0C, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01, 0xFF, 0xFF, 0x80, 0x00, 0x00, 0x00 }; - #elif EXTRUDERS == 2 + #elif HOTENDS == 2 #define STATUS_SCREENWIDTH 115 //Width in pixels #define STATUS_SCREENHEIGHT 19 //Height in pixels #define STATUS_SCREENBYTEWIDTH 15 //Width in bytes @@ -262,7 +262,7 @@ }; #endif // Extruders #else - #if EXTRUDERS == 1 + #if HOTENDS == 1 #define STATUS_SCREENWIDTH 115 //Width in pixels #define STATUS_SCREENHEIGHT 19 //Height in pixels #define STATUS_SCREENBYTEWIDTH 15 //Width in bytes @@ -312,7 +312,7 @@ 0x1E, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x7F, 0xFF, 0xE0, 0x0C, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }; - #elif EXTRUDERS == 2 + #elif HOTENDS == 2 #define STATUS_SCREENWIDTH 115 //Width in pixels #define STATUS_SCREENHEIGHT 19 //Height in pixels #define STATUS_SCREENBYTEWIDTH 15 //Width in bytes diff --git a/Marlin/dogm_lcd_implementation.h b/Marlin/dogm_lcd_implementation.h index fda1f53ab..3399f78bf 100644 --- a/Marlin/dogm_lcd_implementation.h +++ b/Marlin/dogm_lcd_implementation.h @@ -370,10 +370,10 @@ static void lcd_implementation_status_screen() { #endif // Extruders - for (int i = 0; i < EXTRUDERS; i++) _draw_heater_status(5 + i * 25, i); + for (int i = 0; i < HOTENDS; i++) _draw_heater_status(5 + i * 25, i); // Heated bed - #if EXTRUDERS < 4 && HAS_TEMP_BED + #if HOTENDS < 4 && HAS_TEMP_BED _draw_heater_status(81, -1); #endif diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h index 55b806140..2cfe41a9d 100644 --- a/Marlin/example_configurations/Felix/Configuration.h +++ b/Marlin/example_configurations/Felix/Configuration.h @@ -126,8 +126,8 @@ // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. -//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis -//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX @@ -224,8 +224,8 @@ #define BED_MAXTEMP 150 // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS -//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=U^2/R -//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R +//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R //=========================================================================== //============================= PID Settings ================================ @@ -241,8 +241,8 @@ //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay - //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) - // Set/get with gcode: M301 E[extruder number, 0-2] + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term diff --git a/Marlin/example_configurations/Felix/Configuration_adv.h b/Marlin/example_configurations/Felix/Configuration_adv.h index 36c6fcd71..b22bf9591 100644 --- a/Marlin/example_configurations/Felix/Configuration_adv.h +++ b/Marlin/example_configurations/Felix/Configuration_adv.h @@ -237,7 +237,7 @@ #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position - // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops // without modifying the firmware (through the "M218 T1 X???" command). // Remember: you should set the second extruder x-offset to 0 in your slicer. diff --git a/Marlin/example_configurations/Felix/DUAL/Configuration.h b/Marlin/example_configurations/Felix/DUAL/Configuration.h index cebc6794f..0fbcb652d 100644 --- a/Marlin/example_configurations/Felix/DUAL/Configuration.h +++ b/Marlin/example_configurations/Felix/DUAL/Configuration.h @@ -126,8 +126,8 @@ // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. -//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis -//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX @@ -224,8 +224,8 @@ #define BED_MAXTEMP 150 // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS -//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=U^2/R -//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R +//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R //=========================================================================== //============================= PID Settings ================================ @@ -241,8 +241,8 @@ //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay - //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) - // Set/get with gcode: M301 E[extruder number, 0-2] + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h index e2dd327e0..989d6ae27 100644 --- a/Marlin/example_configurations/Hephestos/Configuration.h +++ b/Marlin/example_configurations/Hephestos/Configuration.h @@ -129,8 +129,8 @@ // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. -//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis -//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX @@ -227,8 +227,8 @@ #define BED_MAXTEMP 150 // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS -//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=U^2/R -//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R +//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R //=========================================================================== //============================= PID Settings ================================ @@ -244,8 +244,8 @@ //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay - //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) - // Set/get with gcode: M301 E[extruder number, 0-2] + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term diff --git a/Marlin/example_configurations/Hephestos/Configuration_adv.h b/Marlin/example_configurations/Hephestos/Configuration_adv.h index 50e8ba28f..9a89097d9 100644 --- a/Marlin/example_configurations/Hephestos/Configuration_adv.h +++ b/Marlin/example_configurations/Hephestos/Configuration_adv.h @@ -237,7 +237,7 @@ #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position - // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops // without modifying the firmware (through the "M218 T1 X???" command). // Remember: you should set the second extruder x-offset to 0 in your slicer. diff --git a/Marlin/example_configurations/Hephestos_2/Configuration.h b/Marlin/example_configurations/Hephestos_2/Configuration.h index 1ea120af9..4f2c1fab0 100644 --- a/Marlin/example_configurations/Hephestos_2/Configuration.h +++ b/Marlin/example_configurations/Hephestos_2/Configuration.h @@ -126,8 +126,8 @@ // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. -//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis -//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX @@ -224,8 +224,8 @@ #define BED_MAXTEMP 150 // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS -//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=U^2/R -//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R +//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R //=========================================================================== //============================= PID Settings ================================ @@ -241,8 +241,8 @@ //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay - //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) - // Set/get with gcode: M301 E[extruder number, 0-2] + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 250 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term diff --git a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h index 2fe4d660c..bebd94b89 100644 --- a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h +++ b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h @@ -237,7 +237,7 @@ #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position - // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops // without modifying the firmware (through the "M218 T1 X???" command). // Remember: you should set the second extruder x-offset to 0 in your slicer. diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h index ada26986f..c4c0572c6 100644 --- a/Marlin/example_configurations/K8200/Configuration.h +++ b/Marlin/example_configurations/K8200/Configuration.h @@ -133,8 +133,8 @@ // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. -//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis -//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX @@ -231,8 +231,8 @@ #define BED_MAXTEMP 150 // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS -//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=U^2/R -//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R +//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R //=========================================================================== //============================= PID Settings ================================ @@ -248,8 +248,8 @@ //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay - //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) - // Set/get with gcode: M301 E[extruder number, 0-2] + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term diff --git a/Marlin/example_configurations/K8200/Configuration_adv.h b/Marlin/example_configurations/K8200/Configuration_adv.h index 296ecd2d6..c5e9249c4 100644 --- a/Marlin/example_configurations/K8200/Configuration_adv.h +++ b/Marlin/example_configurations/K8200/Configuration_adv.h @@ -243,7 +243,7 @@ #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position - // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops // without modifying the firmware (through the "M218 T1 X???" command). // Remember: you should set the second extruder x-offset to 0 in your slicer. diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h index 3df2b7bd0..27c70aa97 100644 --- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h +++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h @@ -126,8 +126,8 @@ // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. -//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis -//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX @@ -224,8 +224,8 @@ #define BED_MAXTEMP 150 // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS -//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=U^2/R -//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R +//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R //=========================================================================== //============================= PID Settings ================================ @@ -241,8 +241,8 @@ //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay - //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) - // Set/get with gcode: M301 E[extruder number, 0-2] + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h index d153fa9dd..40910c8cb 100644 --- a/Marlin/example_configurations/RigidBot/Configuration.h +++ b/Marlin/example_configurations/RigidBot/Configuration.h @@ -126,8 +126,8 @@ // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. -#define EXTRUDER_OFFSET_X {0.0, 36.00} // (in mm) for each extruder, offset of the hotend on the X axis -#define EXTRUDER_OFFSET_Y {0.0, 0.00} // (in mm) for each extruder, offset of the hotend on the Y axis +#define HOTEND_OFFSET_X {0.0, 36.00} // (in mm) for each extruder, offset of the hotend on the X axis +#define HOTEND_OFFSET_Y {0.0, 0.00} // (in mm) for each extruder, offset of the hotend on the Y axis //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX @@ -224,8 +224,8 @@ #define BED_MAXTEMP 150 // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS -//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=U^2/R -//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R +//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R //=========================================================================== //============================= PID Settings ================================ @@ -241,8 +241,8 @@ //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay - //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) - // Set/get with gcode: M301 E[extruder number, 0-2] + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term diff --git a/Marlin/example_configurations/RigidBot/Configuration_adv.h b/Marlin/example_configurations/RigidBot/Configuration_adv.h index c8a56e4bd..50d8cb51d 100644 --- a/Marlin/example_configurations/RigidBot/Configuration_adv.h +++ b/Marlin/example_configurations/RigidBot/Configuration_adv.h @@ -237,7 +237,7 @@ #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position - // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops // without modifying the firmware (through the "M218 T1 X???" command). // Remember: you should set the second extruder x-offset to 0 in your slicer. diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h index 1b28aae80..736b835a4 100644 --- a/Marlin/example_configurations/SCARA/Configuration.h +++ b/Marlin/example_configurations/SCARA/Configuration.h @@ -151,8 +151,8 @@ // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. -//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis -//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX @@ -249,8 +249,8 @@ #define BED_MAXTEMP 150 // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS -#define EXTRUDER_WATTS (2*2/5.9) // P=U^2/R -#define BED_WATTS (5.45*5.45/2.2) // P=U^2/R +#define HOTEND_WATTS (2*2/5.9) // P=U^2/R +#define BED_WATTS (5.45*5.45/2.2) // P=U^2/R //=========================================================================== //============================= PID Settings ================================ @@ -266,8 +266,8 @@ //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay - //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) - // Set/get with gcode: M301 E[extruder number, 0-2] + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term diff --git a/Marlin/example_configurations/SCARA/Configuration_adv.h b/Marlin/example_configurations/SCARA/Configuration_adv.h index 257142419..f3ba7282b 100644 --- a/Marlin/example_configurations/SCARA/Configuration_adv.h +++ b/Marlin/example_configurations/SCARA/Configuration_adv.h @@ -237,7 +237,7 @@ #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position - // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops // without modifying the firmware (through the "M218 T1 X???" command). // Remember: you should set the second extruder x-offset to 0 in your slicer. diff --git a/Marlin/example_configurations/TAZ4/Configuration.h b/Marlin/example_configurations/TAZ4/Configuration.h index a0197907b..4586e843f 100644 --- a/Marlin/example_configurations/TAZ4/Configuration.h +++ b/Marlin/example_configurations/TAZ4/Configuration.h @@ -126,8 +126,8 @@ // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. -//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis -//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX @@ -224,8 +224,8 @@ #define BED_MAXTEMP 150 // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS -//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=U^2/R -//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R +//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R //=========================================================================== //============================= PID Settings ================================ @@ -241,8 +241,8 @@ //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay - //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) - // Set/get with gcode: M301 E[extruder number, 0-2] + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 16 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term diff --git a/Marlin/example_configurations/TAZ4/Configuration_adv.h b/Marlin/example_configurations/TAZ4/Configuration_adv.h index 7dfb96e44..5aa9487e9 100644 --- a/Marlin/example_configurations/TAZ4/Configuration_adv.h +++ b/Marlin/example_configurations/TAZ4/Configuration_adv.h @@ -245,7 +245,7 @@ #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position - // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops // without modifying the firmware (through the "M218 T1 X???" command). // Remember: you should set the second extruder x-offset to 0 in your slicer. diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h index cdd075c83..58bb250ab 100644 --- a/Marlin/example_configurations/WITBOX/Configuration.h +++ b/Marlin/example_configurations/WITBOX/Configuration.h @@ -129,8 +129,8 @@ // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. -//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis -//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX @@ -227,8 +227,8 @@ #define BED_MAXTEMP 150 // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS -//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=U^2/R -//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R +//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R //=========================================================================== //============================= PID Settings ================================ @@ -244,8 +244,8 @@ //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay - //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) - // Set/get with gcode: M301 E[extruder number, 0-2] + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term diff --git a/Marlin/example_configurations/WITBOX/Configuration_adv.h b/Marlin/example_configurations/WITBOX/Configuration_adv.h index 50e8ba28f..9a89097d9 100644 --- a/Marlin/example_configurations/WITBOX/Configuration_adv.h +++ b/Marlin/example_configurations/WITBOX/Configuration_adv.h @@ -237,7 +237,7 @@ #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position - // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops // without modifying the firmware (through the "M218 T1 X???" command). // Remember: you should set the second extruder x-offset to 0 in your slicer. diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h index 7a5d012d6..5cec85584 100644 --- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h +++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h @@ -126,8 +126,8 @@ // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. -//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis -//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX @@ -224,8 +224,8 @@ #define BED_MAXTEMP 150 // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS -//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=U^2/R -//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R +//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R //=========================================================================== //============================= PID Settings ================================ @@ -241,8 +241,8 @@ //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay - //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) - // Set/get with gcode: M301 E[extruder number, 0-2] + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration.h b/Marlin/example_configurations/delta/biv2.5/Configuration.h index 739af6ece..94565f1aa 100644 --- a/Marlin/example_configurations/delta/biv2.5/Configuration.h +++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h @@ -126,8 +126,8 @@ // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. -//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis -//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX @@ -224,8 +224,8 @@ #define BED_MAXTEMP 150 // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS -//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=U^2/R -//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R +//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R //=========================================================================== //============================= PID Settings ================================ @@ -241,8 +241,8 @@ //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay - //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) - // Set/get with gcode: M301 E[extruder number, 0-2] + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h index ecfe11c39..627188d92 100644 --- a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h +++ b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h @@ -237,7 +237,7 @@ #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position - // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops // without modifying the firmware (through the "M218 T1 X???" command). // Remember: you should set the second extruder x-offset to 0 in your slicer. diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h index 714152c72..c04ba9942 100644 --- a/Marlin/example_configurations/delta/generic/Configuration.h +++ b/Marlin/example_configurations/delta/generic/Configuration.h @@ -126,8 +126,8 @@ // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. -//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis -//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX @@ -224,8 +224,8 @@ #define BED_MAXTEMP 150 // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS -//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=U^2/R -//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R +//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R //=========================================================================== //============================= PID Settings ================================ @@ -241,8 +241,8 @@ //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay - //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) - // Set/get with gcode: M301 E[extruder number, 0-2] + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term diff --git a/Marlin/example_configurations/delta/generic/Configuration_adv.h b/Marlin/example_configurations/delta/generic/Configuration_adv.h index 145c3cdee..d64dfd5f3 100644 --- a/Marlin/example_configurations/delta/generic/Configuration_adv.h +++ b/Marlin/example_configurations/delta/generic/Configuration_adv.h @@ -237,7 +237,7 @@ #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position - // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops // without modifying the firmware (through the "M218 T1 X???" command). // Remember: you should set the second extruder x-offset to 0 in your slicer. diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h index e9e5c428a..7e9d06d84 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h @@ -126,8 +126,8 @@ // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. -//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis -//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX @@ -224,8 +224,8 @@ #define BED_MAXTEMP 150 // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS -//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=U^2/R -//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R +//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R //=========================================================================== //============================= PID Settings ================================ @@ -241,8 +241,8 @@ //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay - //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) - // Set/get with gcode: M301 E[extruder number, 0-2] + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h index 4e629b43e..f99318ea3 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h @@ -237,7 +237,7 @@ #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position - // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops // without modifying the firmware (through the "M218 T1 X???" command). // Remember: you should set the second extruder x-offset to 0 in your slicer. diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h index 406edd16a..8e21082dd 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h @@ -132,8 +132,8 @@ // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. -//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis -//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX @@ -230,8 +230,8 @@ #define BED_MAXTEMP 150 // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS -//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=U^2/R -//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R +//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R //=========================================================================== //============================= PID Settings ================================ @@ -247,8 +247,8 @@ //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay - //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) - // Set/get with gcode: M301 E[extruder number, 0-2] + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 50 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h index cc7d88b72..3250e88ff 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h @@ -242,7 +242,7 @@ #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position - // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops // without modifying the firmware (through the "M218 T1 X???" command). // Remember: you should set the second extruder x-offset to 0 in your slicer. diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration.h b/Marlin/example_configurations/delta/kossel_xl/Configuration.h index ab5403574..0c5efa12e 100644 --- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h @@ -119,8 +119,8 @@ // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. -//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis -//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX @@ -217,8 +217,8 @@ #define BED_MAXTEMP 150 // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS -//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=U^2/R -//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R +//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R //=========================================================================== //============================= PID Settings ================================ @@ -234,8 +234,8 @@ //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay - //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) - // Set/get with gcode: M301 E[extruder number, 0-2] + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h index 3d90e5a65..f0ccba6a4 100644 --- a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h @@ -237,7 +237,7 @@ #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position - // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops // without modifying the firmware (through the "M218 T1 X???" command). // Remember: you should set the second extruder x-offset to 0 in your slicer. diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h index 55696956d..615fec082 100644 --- a/Marlin/example_configurations/makibox/Configuration.h +++ b/Marlin/example_configurations/makibox/Configuration.h @@ -126,8 +126,8 @@ // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. -//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis -//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX @@ -224,8 +224,8 @@ #define BED_MAXTEMP 150 // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS -//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=U^2/R -//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R +//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R //=========================================================================== //============================= PID Settings ================================ @@ -241,8 +241,8 @@ //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay - //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) - // Set/get with gcode: M301 E[extruder number, 0-2] + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term diff --git a/Marlin/example_configurations/makibox/Configuration_adv.h b/Marlin/example_configurations/makibox/Configuration_adv.h index 1621cbd31..d8ef5d30c 100644 --- a/Marlin/example_configurations/makibox/Configuration_adv.h +++ b/Marlin/example_configurations/makibox/Configuration_adv.h @@ -237,7 +237,7 @@ #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position - // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops // without modifying the firmware (through the "M218 T1 X???" command). // Remember: you should set the second extruder x-offset to 0 in your slicer. diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h index fc52ac4cb..4c9cbe352 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h @@ -126,8 +126,8 @@ // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. -//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis -//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //// The following define selects which power supply you have. Please choose the one that matches your setup // 1 = ATX @@ -224,8 +224,8 @@ #define BED_MAXTEMP 150 // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS -//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=U^2/R -//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R +//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=U^2/R //=========================================================================== //============================= PID Settings ================================ @@ -241,8 +241,8 @@ //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay - //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) - // Set/get with gcode: M301 E[extruder number, 0-2] + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h index 81db41194..af2d22f9c 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h @@ -237,7 +237,7 @@ #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position - // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops // without modifying the firmware (through the "M218 T1 X???" command). // Remember: you should set the second extruder x-offset to 0 in your slicer. diff --git a/Marlin/pins.h b/Marlin/pins.h index 8447db61e..a9baf198c 100644 --- a/Marlin/pins.h +++ b/Marlin/pins.h @@ -243,20 +243,38 @@ #define marlinAnalogInputToDigitalPin(p) ((p) == -1 ? -1 : (p) + 0xA0) // List of pins which to ignore when asked to change by gcode, 0 and 1 are RX and TX, do not mess with those! -#define _E0_PINS E0_STEP_PIN, E0_DIR_PIN, E0_ENABLE_PIN, E0_MS1_PIN, E0_MS2_PIN, HEATER_0_PIN, EXTRUDER_0_AUTO_FAN_PIN, marlinAnalogInputToDigitalPin(TEMP_0_PIN), +#define _E0_PINS E0_STEP_PIN, E0_DIR_PIN, E0_ENABLE_PIN, E0_MS1_PIN, E0_MS2_PIN, #define _E1_PINS #define _E2_PINS #define _E3_PINS #if EXTRUDERS > 1 #undef _E1_PINS - #define _E1_PINS E1_STEP_PIN, E1_DIR_PIN, E1_ENABLE_PIN, HEATER_1_PIN, E1_MS1_PIN, E1_MS2_PIN, EXTRUDER_1_AUTO_FAN_PIN, marlinAnalogInputToDigitalPin(TEMP_1_PIN), + #define _E1_PINS E1_STEP_PIN, E1_DIR_PIN, E1_ENABLE_PIN, E1_MS1_PIN, E1_MS2_PIN, #if EXTRUDERS > 2 #undef _E2_PINS - #define _E2_PINS E2_STEP_PIN, E2_DIR_PIN, E2_ENABLE_PIN, HEATER_2_PIN, EXTRUDER_2_AUTO_FAN_PIN, marlinAnalogInputToDigitalPin(TEMP_2_PIN), + #define _E2_PINS E2_STEP_PIN, E2_DIR_PIN, E2_ENABLE_PIN, #if EXTRUDERS > 3 #undef _E3_PINS - #define _E3_PINS E3_STEP_PIN, E3_DIR_PIN, E3_ENABLE_PIN, HEATER_3_PIN, EXTRUDER_3_AUTO_FAN_PIN, marlinAnalogInputToDigitalPin(TEMP_3_PIN), + #define _E3_PINS E3_STEP_PIN, E3_DIR_PIN, E3_ENABLE_PIN, + #endif + #endif +#endif + +#define _H0_PINS HEATER_0_PIN, EXTRUDER_0_AUTO_FAN_PIN, marlinAnalogInputToDigitalPin(TEMP_0_PIN), +#define _H1_PINS +#define _H2_PINS +#define _H3_PINS + +#if HOTENDS > 1 + #undef _H1_PINS + #define _H1_PINS HEATER_1_PIN, EXTRUDER_1_AUTO_FAN_PIN, marlinAnalogInputToDigitalPin(TEMP_1_PIN), + #if HOTENDS > 2 + #undef _H2_PINS + #define _H2_PINS HEATER_2_PIN, EXTRUDER_2_AUTO_FAN_PIN, marlinAnalogInputToDigitalPin(TEMP_2_PIN), + #if HOTENDS > 3 + #undef _H3_PINS + #define _H3_PINS HEATER_3_PIN, EXTRUDER_3_AUTO_FAN_PIN, marlinAnalogInputToDigitalPin(TEMP_3_PIN), #endif #endif #endif @@ -383,6 +401,7 @@ Z_STEP_PIN, Z_DIR_PIN, Z_ENABLE_PIN, Z_MIN_PIN, Z_MAX_PIN, Z_MIN_PROBE_PIN, \ PS_ON_PIN, HEATER_BED_PIN, FAN_PIN, FAN1_PIN, FAN2_PIN, CONTROLLERFAN_PIN, \ _E0_PINS _E1_PINS _E2_PINS _E3_PINS BED_PINS \ + _H0_PINS _H1_PINS _H2_PINS _H3_PINS \ _X2_PINS _Y2_PINS _Z2_PINS \ X_MS1_PIN, X_MS2_PIN, Y_MS1_PIN, Y_MS2_PIN, Z_MS1_PIN, Z_MS2_PIN \ } diff --git a/Marlin/pins_MEGACONTROLLER.h b/Marlin/pins_MEGACONTROLLER.h index d7d5418d3..8e423a3bc 100644 --- a/Marlin/pins_MEGACONTROLLER.h +++ b/Marlin/pins_MEGACONTROLLER.h @@ -28,7 +28,7 @@ #error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu." #endif -#if EXTRUDERS > 2 +#if EXTRUDERS > 2 || HOTENDS > 2 #error "Mega Controller supports up to 2 extruders. Comment this line to keep going." #endif diff --git a/Marlin/pins_RAMPS_14.h b/Marlin/pins_RAMPS_14.h index 612e8ec31..9c8caa27c 100644 --- a/Marlin/pins_RAMPS_14.h +++ b/Marlin/pins_RAMPS_14.h @@ -25,16 +25,16 @@ * * Applies to the following boards: * - * RAMPS_14_EFB (Extruder, Fan, Bed) - * RAMPS_14_EEB (Extruder, Extruder, Bed) - * RAMPS_14_EFF (Extruder, Fan, Fan) - * RAMPS_14_EEF (Extruder, Extruder, Fan) + * RAMPS_14_EFB (Hotend, Fan, Bed) + * RAMPS_14_EEB (Hotend0, Hotend1, Bed) + * RAMPS_14_EFF (Hotend, Fan0, Fan1) + * RAMPS_14_EEF (Hotend0, Hotend1, Fan) * RAMPS_14_SF (Spindle, Controller Fan) * - * RAMPS_13_EFB (Extruder, Fan, Bed) - * RAMPS_13_EEB (Extruder, Extruder, Bed) - * RAMPS_13_EFF (Extruder, Fan, Fan) - * RAMPS_13_EEF (Extruder, Extruder, Fan) + * RAMPS_13_EFB (Hotend, Fan, Bed) + * RAMPS_13_EEB (Hotend0, Hotend1, Bed) + * RAMPS_13_EFF (Hotend, Fan0, Fan1) + * RAMPS_13_EEF (Hotend0, Hotend1, Fan) * RAMPS_13_SF (Spindle, Controller Fan) * * Other pins_MYBOARD.h files may override these defaults diff --git a/Marlin/pins_RUMBA.h b/Marlin/pins_RUMBA.h index d92f3a835..e086ec446 100644 --- a/Marlin/pins_RUMBA.h +++ b/Marlin/pins_RUMBA.h @@ -28,7 +28,7 @@ #error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu." #endif -#if EXTRUDERS > 3 +#if EXTRUDERS > 3 || HOTENDS > 3 #error "RUMBA supports up to 3 extruders. Comment this line to keep going." #endif diff --git a/Marlin/temperature.cpp b/Marlin/temperature.cpp index 02766f8be..61d9fe2e2 100644 --- a/Marlin/temperature.cpp +++ b/Marlin/temperature.cpp @@ -42,17 +42,17 @@ static void* heater_ttbl_map[2] = {(void*)HEATER_0_TEMPTABLE, (void*)HEATER_1_TEMPTABLE }; static uint8_t heater_ttbllen_map[2] = { HEATER_0_TEMPTABLE_LEN, HEATER_1_TEMPTABLE_LEN }; #else - static void* heater_ttbl_map[EXTRUDERS] = ARRAY_BY_EXTRUDERS((void*)HEATER_0_TEMPTABLE, (void*)HEATER_1_TEMPTABLE, (void*)HEATER_2_TEMPTABLE, (void*)HEATER_3_TEMPTABLE); - static uint8_t heater_ttbllen_map[EXTRUDERS] = ARRAY_BY_EXTRUDERS(HEATER_0_TEMPTABLE_LEN, HEATER_1_TEMPTABLE_LEN, HEATER_2_TEMPTABLE_LEN, HEATER_3_TEMPTABLE_LEN); + static void* heater_ttbl_map[HOTENDS] = ARRAY_BY_HOTENDS((void*)HEATER_0_TEMPTABLE, (void*)HEATER_1_TEMPTABLE, (void*)HEATER_2_TEMPTABLE, (void*)HEATER_3_TEMPTABLE); + static uint8_t heater_ttbllen_map[HOTENDS] = ARRAY_BY_HOTENDS(HEATER_0_TEMPTABLE_LEN, HEATER_1_TEMPTABLE_LEN, HEATER_2_TEMPTABLE_LEN, HEATER_3_TEMPTABLE_LEN); #endif Temperature thermalManager; // public: -int Temperature::current_temperature_raw[EXTRUDERS] = { 0 }; -float Temperature::current_temperature[EXTRUDERS] = { 0.0 }; -int Temperature::target_temperature[EXTRUDERS] = { 0 }; +int Temperature::current_temperature_raw[HOTENDS] = { 0 }; +float Temperature::current_temperature[HOTENDS] = { 0.0 }; +int Temperature::target_temperature[HOTENDS] = { 0 }; int Temperature::current_temperature_bed_raw = 0; float Temperature::current_temperature_bed = 0.0; @@ -69,12 +69,12 @@ unsigned char Temperature::soft_pwm_bed; #endif #if ENABLED(PIDTEMP) - #if ENABLED(PID_PARAMS_PER_EXTRUDER) - float Temperature::Kp[EXTRUDERS] = ARRAY_BY_EXTRUDERS1(DEFAULT_Kp), - Temperature::Ki[EXTRUDERS] = ARRAY_BY_EXTRUDERS1((DEFAULT_Ki) * (PID_dT)), - Temperature::Kd[EXTRUDERS] = ARRAY_BY_EXTRUDERS1((DEFAULT_Kd) / (PID_dT)); + #if ENABLED(PID_PARAMS_PER_HOTEND) + float Temperature::Kp[HOTENDS] = ARRAY_BY_HOTENDS1(DEFAULT_Kp), + Temperature::Ki[HOTENDS] = ARRAY_BY_HOTENDS1((DEFAULT_Ki) * (PID_dT)), + Temperature::Kd[HOTENDS] = ARRAY_BY_HOTENDS1((DEFAULT_Kd) / (PID_dT)); #if ENABLED(PID_ADD_EXTRUSION_RATE) - float Temperature::Kc[EXTRUDERS] = ARRAY_BY_EXTRUDERS1(DEFAULT_Kc); + float Temperature::Kc[HOTENDS] = ARRAY_BY_HOTENDS1(DEFAULT_Kc); #endif #else float Temperature::Kp = DEFAULT_Kp, @@ -97,8 +97,8 @@ unsigned char Temperature::soft_pwm_bed; #endif #if ENABLED(THERMAL_PROTECTION_HOTENDS) && WATCH_TEMP_PERIOD > 0 - int Temperature::watch_target_temp[EXTRUDERS] = { 0 }; - millis_t Temperature::watch_heater_next_ms[EXTRUDERS] = { 0 }; + int Temperature::watch_target_temp[HOTENDS] = { 0 }; + millis_t Temperature::watch_heater_next_ms[HOTENDS] = { 0 }; #endif #if ENABLED(THERMAL_PROTECTION_HOTENDS) && WATCH_BED_TEMP_PERIOD > 0 @@ -120,23 +120,23 @@ unsigned char Temperature::soft_pwm_bed; volatile bool Temperature::temp_meas_ready = false; #if ENABLED(PIDTEMP) - float Temperature::temp_iState[EXTRUDERS] = { 0 }; - float Temperature::temp_dState[EXTRUDERS] = { 0 }; - float Temperature::pTerm[EXTRUDERS]; - float Temperature::iTerm[EXTRUDERS]; - float Temperature::dTerm[EXTRUDERS]; + float Temperature::temp_iState[HOTENDS] = { 0 }; + float Temperature::temp_dState[HOTENDS] = { 0 }; + float Temperature::pTerm[HOTENDS]; + float Temperature::iTerm[HOTENDS]; + float Temperature::dTerm[HOTENDS]; #if ENABLED(PID_ADD_EXTRUSION_RATE) - float Temperature::cTerm[EXTRUDERS]; - long Temperature::last_position[EXTRUDERS]; + float Temperature::cTerm[HOTENDS]; + long Temperature::last_position[HOTENDS]; long Temperature::lpq[LPQ_MAX_LEN]; int Temperature::lpq_ptr = 0; #endif - float Temperature::pid_error[EXTRUDERS]; - float Temperature::temp_iState_min[EXTRUDERS]; - float Temperature::temp_iState_max[EXTRUDERS]; - bool Temperature::pid_reset[EXTRUDERS]; + float Temperature::pid_error[HOTENDS]; + float Temperature::temp_iState_min[HOTENDS]; + float Temperature::temp_iState_max[HOTENDS]; + bool Temperature::pid_reset[HOTENDS]; #endif #if ENABLED(PIDTEMPBED) @@ -156,10 +156,10 @@ unsigned long Temperature::raw_temp_value[4] = { 0 }; unsigned long Temperature::raw_temp_bed_value = 0; // Init min and max temp with extreme values to prevent false errors during startup -int Temperature::minttemp_raw[EXTRUDERS] = ARRAY_BY_EXTRUDERS(HEATER_0_RAW_LO_TEMP , HEATER_1_RAW_LO_TEMP , HEATER_2_RAW_LO_TEMP, HEATER_3_RAW_LO_TEMP); -int Temperature::maxttemp_raw[EXTRUDERS] = ARRAY_BY_EXTRUDERS(HEATER_0_RAW_HI_TEMP , HEATER_1_RAW_HI_TEMP , HEATER_2_RAW_HI_TEMP, HEATER_3_RAW_HI_TEMP); -int Temperature::minttemp[EXTRUDERS] = { 0 }; -int Temperature::maxttemp[EXTRUDERS] = ARRAY_BY_EXTRUDERS1(16383); +int Temperature::minttemp_raw[HOTENDS] = ARRAY_BY_HOTENDS(HEATER_0_RAW_LO_TEMP , HEATER_1_RAW_LO_TEMP , HEATER_2_RAW_LO_TEMP, HEATER_3_RAW_LO_TEMP); +int Temperature::maxttemp_raw[HOTENDS] = ARRAY_BY_HOTENDS(HEATER_0_RAW_HI_TEMP , HEATER_1_RAW_HI_TEMP , HEATER_2_RAW_HI_TEMP, HEATER_3_RAW_HI_TEMP); +int Temperature::minttemp[HOTENDS] = { 0 }; +int Temperature::maxttemp[HOTENDS] = ARRAY_BY_HOTENDS1(16383); #ifdef BED_MINTEMP int Temperature::bed_minttemp_raw = HEATER_BED_RAW_LO_TEMP; @@ -177,7 +177,7 @@ int Temperature::maxttemp[EXTRUDERS] = ARRAY_BY_EXTRUDERS1(16383); millis_t Temperature::next_auto_fan_check_ms; #endif -unsigned char Temperature::soft_pwm[EXTRUDERS]; +unsigned char Temperature::soft_pwm[HOTENDS]; #if ENABLED(FAN_SOFT_PWM) unsigned char Temperature::soft_pwm_fan[FAN_COUNT]; @@ -189,7 +189,7 @@ unsigned char Temperature::soft_pwm[EXTRUDERS]; #if HAS_PID_HEATING - void Temperature::PID_autotune(float temp, int extruder, int ncycles, bool set_result/*=false*/) { + void Temperature::PID_autotune(float temp, int hotend, int ncycles, bool set_result/*=false*/) { float input = 0.0; int cycles = 0; bool heating = true; @@ -208,12 +208,12 @@ unsigned char Temperature::soft_pwm[EXTRUDERS]; if (false #if ENABLED(PIDTEMP) - || extruder >= EXTRUDERS + || hotend >= HOTENDS #else - || extruder >= 0 + || hotend >= 0 #endif #if DISABLED(PIDTEMPBED) - || extruder < 0 + || hotend < 0 #endif ) { SERIAL_ECHOLN(MSG_PID_BAD_EXTRUDER_NUM); @@ -225,12 +225,12 @@ unsigned char Temperature::soft_pwm[EXTRUDERS]; disable_all_heaters(); // switch off all heaters. #if HAS_PID_FOR_BOTH - if (extruder < 0) + if (hotend < 0) soft_pwm_bed = bias = d = (MAX_BED_POWER) / 2; else - soft_pwm[extruder] = bias = d = (PID_MAX) / 2; + soft_pwm[hotend] = bias = d = (PID_MAX) / 2; #elif ENABLED(PIDTEMP) - soft_pwm[extruder] = bias = d = (PID_MAX) / 2; + soft_pwm[hotend] = bias = d = (PID_MAX) / 2; #else soft_pwm_bed = bias = d = (MAX_BED_POWER) / 2; #endif @@ -245,9 +245,9 @@ unsigned char Temperature::soft_pwm[EXTRUDERS]; input = #if HAS_PID_FOR_BOTH - extruder < 0 ? current_temperature_bed : current_temperature[extruder] + hotend < 0 ? current_temperature_bed : current_temperature[hotend] #elif ENABLED(PIDTEMP) - current_temperature[extruder] + current_temperature[hotend] #else current_temperature_bed #endif @@ -267,12 +267,12 @@ unsigned char Temperature::soft_pwm[EXTRUDERS]; if (ELAPSED(ms, t2 + 5000UL)) { heating = false; #if HAS_PID_FOR_BOTH - if (extruder < 0) + if (hotend < 0) soft_pwm_bed = (bias - d) >> 1; else - soft_pwm[extruder] = (bias - d) >> 1; + soft_pwm[hotend] = (bias - d) >> 1; #elif ENABLED(PIDTEMP) - soft_pwm[extruder] = (bias - d) >> 1; + soft_pwm[hotend] = (bias - d) >> 1; #elif ENABLED(PIDTEMPBED) soft_pwm_bed = (bias - d) >> 1; #endif @@ -290,7 +290,7 @@ unsigned char Temperature::soft_pwm[EXTRUDERS]; if (cycles > 0) { long max_pow = #if HAS_PID_FOR_BOTH - extruder < 0 ? MAX_BED_POWER : PID_MAX + hotend < 0 ? MAX_BED_POWER : PID_MAX #elif ENABLED(PIDTEMP) PID_MAX #else @@ -336,12 +336,12 @@ unsigned char Temperature::soft_pwm[EXTRUDERS]; } } #if HAS_PID_FOR_BOTH - if (extruder < 0) + if (hotend < 0) soft_pwm_bed = (bias + d) >> 1; else - soft_pwm[extruder] = (bias + d) >> 1; + soft_pwm[hotend] = (bias + d) >> 1; #elif ENABLED(PIDTEMP) - soft_pwm[extruder] = (bias + d) >> 1; + soft_pwm[hotend] = (bias + d) >> 1; #else soft_pwm_bed = (bias + d) >> 1; #endif @@ -373,7 +373,7 @@ unsigned char Temperature::soft_pwm[EXTRUDERS]; SERIAL_PROTOCOLLNPGM(MSG_PID_AUTOTUNE_FINISHED); #if HAS_PID_FOR_BOTH - const char* estring = extruder < 0 ? "bed" : ""; + const char* estring = hotend < 0 ? "bed" : ""; SERIAL_PROTOCOLPGM("#define DEFAULT_"); SERIAL_PROTOCOL(estring); SERIAL_PROTOCOLPGM("Kp "); SERIAL_PROTOCOLLN(workKp); SERIAL_PROTOCOLPGM("#define DEFAULT_"); SERIAL_PROTOCOL(estring); SERIAL_PROTOCOLPGM("Ki "); SERIAL_PROTOCOLLN(workKi); SERIAL_PROTOCOLPGM("#define DEFAULT_"); SERIAL_PROTOCOL(estring); SERIAL_PROTOCOLPGM("Kd "); SERIAL_PROTOCOLLN(workKd); @@ -394,15 +394,15 @@ unsigned char Temperature::soft_pwm[EXTRUDERS]; updatePID() #define _SET_EXTRUDER_PID() \ - PID_PARAM(Kp, extruder) = workKp; \ - PID_PARAM(Ki, extruder) = scalePID_i(workKi); \ - PID_PARAM(Kd, extruder) = scalePID_d(workKd); \ + PID_PARAM(Kp, hotend) = workKp; \ + PID_PARAM(Ki, hotend) = scalePID_i(workKi); \ + PID_PARAM(Kd, hotend) = scalePID_d(workKd); \ updatePID() // Use the result? (As with "M303 U1") if (set_result) { #if HAS_PID_FOR_BOTH - if (extruder < 0) { + if (hotend < 0) { _SET_BED_PID(); } else { @@ -430,7 +430,7 @@ Temperature::Temperature() { } void Temperature::updatePID() { #if ENABLED(PIDTEMP) - for (int e = 0; e < EXTRUDERS; e++) { + for (int e = 0; e < HOTENDS; e++) { temp_iState_max[e] = (PID_INTEGRAL_DRIVE_MAX) / PID_PARAM(Ki, e); #if ENABLED(PID_ADD_EXTRUSION_RATE) last_position[e] = 0; @@ -459,7 +459,7 @@ int Temperature::getHeaterPower(int heater) { EXTRUDER_3_AUTO_FAN_PIN == EXTRUDER_2_AUTO_FAN_PIN ? 2 : 3 }; uint8_t fanState = 0; - for (int f = 0; f <= EXTRUDERS; f++) { + for (int f = 0; f <= HOTENDS; f++) { if (current_temperature[f] > EXTRUDER_AUTO_FAN_TEMPERATURE) SBI(fanState, fanBit[f]); } @@ -665,8 +665,8 @@ void Temperature::manage_heater() { millis_t ms = millis(); #endif - // Loop through all extruders - for (int e = 0; e < EXTRUDERS; e++) { + // Loop through all hotends + for (int e = 0; e < HOTENDS; e++) { #if ENABLED(THERMAL_PROTECTION_HOTENDS) thermal_runaway_protection(&thermal_runaway_state_machine[e], &thermal_runaway_timer[e], current_temperature[e], target_temperature[e], e, THERMAL_PROTECTION_PERIOD, THERMAL_PROTECTION_HYSTERESIS); @@ -719,7 +719,7 @@ void Temperature::manage_heater() { } #endif - } // Extruders Loop + } // Hotends Loop #if HAS_AUTO_FAN if (ELAPSED(ms, next_auto_fan_check_ms)) { // only need to check fan state very infrequently @@ -790,9 +790,9 @@ void Temperature::manage_heater() { // For hot end temperature measurement. float Temperature::analog2temp(int raw, uint8_t e) { #if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT) - if (e > EXTRUDERS) + if (e > HOTENDS) #else - if (e >= EXTRUDERS) + if (e >= HOTENDS) #endif { SERIAL_ERROR_START; @@ -873,7 +873,7 @@ void Temperature::updateTemperaturesFromRawValues() { #if ENABLED(HEATER_0_USES_MAX6675) current_temperature_raw[0] = read_max6675(); #endif - for (uint8_t e = 0; e < EXTRUDERS; e++) { + for (uint8_t e = 0; e < HOTENDS; e++) { current_temperature[e] = Temperature::analog2temp(current_temperature_raw[e], e); } current_temperature_bed = Temperature::analog2tempBed(current_temperature_bed_raw); @@ -926,8 +926,8 @@ void Temperature::init() { MCUCR = _BV(JTD); #endif - // Finish init of mult extruder arrays - for (int e = 0; e < EXTRUDERS; e++) { + // Finish init of mult hotend arrays + for (int e = 0; e < HOTENDS; e++) { // populate with the first value maxttemp[e] = maxttemp[0]; #if ENABLED(PIDTEMP) @@ -1083,30 +1083,30 @@ void Temperature::init() { #ifdef HEATER_0_MAXTEMP TEMP_MAX_ROUTINE(0); #endif - #if EXTRUDERS > 1 + #if HOTENDS > 1 #ifdef HEATER_1_MINTEMP TEMP_MIN_ROUTINE(1); #endif #ifdef HEATER_1_MAXTEMP TEMP_MAX_ROUTINE(1); #endif - #if EXTRUDERS > 2 + #if HOTENDS > 2 #ifdef HEATER_2_MINTEMP TEMP_MIN_ROUTINE(2); #endif #ifdef HEATER_2_MAXTEMP TEMP_MAX_ROUTINE(2); #endif - #if EXTRUDERS > 3 + #if HOTENDS > 3 #ifdef HEATER_3_MINTEMP TEMP_MIN_ROUTINE(3); #endif #ifdef HEATER_3_MAXTEMP TEMP_MAX_ROUTINE(3); #endif - #endif // EXTRUDERS > 3 - #endif // EXTRUDERS > 2 - #endif // EXTRUDERS > 1 + #endif // HOTENDS > 3 + #endif // HOTENDS > 2 + #endif // HOTENDS > 1 #ifdef BED_MINTEMP while(analog2tempBed(bed_minttemp_raw) < BED_MINTEMP) { @@ -1163,8 +1163,8 @@ void Temperature::init() { #if ENABLED(THERMAL_PROTECTION_HOTENDS) || HAS_THERMALLY_PROTECTED_BED #if ENABLED(THERMAL_PROTECTION_HOTENDS) - Temperature::TRState Temperature::thermal_runaway_state_machine[EXTRUDERS] = { TRInactive }; - millis_t Temperature::thermal_runaway_timer[EXTRUDERS] = { 0 }; + Temperature::TRState Temperature::thermal_runaway_state_machine[HOTENDS] = { TRInactive }; + millis_t Temperature::thermal_runaway_timer[HOTENDS] = { 0 }; #endif #if HAS_THERMALLY_PROTECTED_BED @@ -1174,7 +1174,7 @@ void Temperature::init() { void Temperature::thermal_runaway_protection(Temperature::TRState* state, millis_t* timer, float temperature, float target_temperature, int heater_id, int period_seconds, int hysteresis_degc) { - static float tr_target_temperature[EXTRUDERS + 1] = { 0.0 }; + static float tr_target_temperature[HOTENDS + 1] = { 0.0 }; /** SERIAL_ECHO_START; @@ -1187,7 +1187,7 @@ void Temperature::init() { SERIAL_EOL; */ - int heater_index = heater_id >= 0 ? heater_id : EXTRUDERS; + int heater_index = heater_id >= 0 ? heater_id : HOTENDS; // If the target temperature changes, restart if (tr_target_temperature[heater_index] != target_temperature) { @@ -1218,7 +1218,7 @@ void Temperature::init() { #endif // THERMAL_PROTECTION_HOTENDS || THERMAL_PROTECTION_BED void Temperature::disable_all_heaters() { - for (int i = 0; i < EXTRUDERS; i++) setTargetHotend(0, i); + for (int i = 0; i < HOTENDS; i++) setTargetHotend(0, i); setTargetBed(0); // If all heaters go down then for sure our print job has stopped @@ -1236,15 +1236,15 @@ void Temperature::disable_all_heaters() { WRITE_HEATER_0P(LOW); // Should HEATERS_PARALLEL apply here? Then change to DISABLE_HEATER(0) #endif - #if EXTRUDERS > 1 && HAS_TEMP_1 + #if HOTENDS > 1 && HAS_TEMP_1 DISABLE_HEATER(1); #endif - #if EXTRUDERS > 2 && HAS_TEMP_2 + #if HOTENDS > 2 && HAS_TEMP_2 DISABLE_HEATER(2); #endif - #if EXTRUDERS > 3 && HAS_TEMP_3 + #if HOTENDS > 3 && HAS_TEMP_3 DISABLE_HEATER(3); #endif @@ -1390,11 +1390,11 @@ void Temperature::isr() { // Statics per heater ISR_STATICS(0); - #if (EXTRUDERS > 1) || ENABLED(HEATERS_PARALLEL) + #if (HOTENDS > 1) || ENABLED(HEATERS_PARALLEL) ISR_STATICS(1); - #if EXTRUDERS > 2 + #if HOTENDS > 2 ISR_STATICS(2); - #if EXTRUDERS > 3 + #if HOTENDS > 3 ISR_STATICS(3); #endif #endif @@ -1418,13 +1418,13 @@ void Temperature::isr() { } else WRITE_HEATER_0P(0); // If HEATERS_PARALLEL should apply, change to WRITE_HEATER_0 - #if EXTRUDERS > 1 + #if HOTENDS > 1 soft_pwm_1 = soft_pwm[1]; WRITE_HEATER_1(soft_pwm_1 > 0 ? 1 : 0); - #if EXTRUDERS > 2 + #if HOTENDS > 2 soft_pwm_2 = soft_pwm[2]; WRITE_HEATER_2(soft_pwm_2 > 0 ? 1 : 0); - #if EXTRUDERS > 3 + #if HOTENDS > 3 soft_pwm_3 = soft_pwm[3]; WRITE_HEATER_3(soft_pwm_3 > 0 ? 1 : 0); #endif @@ -1453,11 +1453,11 @@ void Temperature::isr() { } if (soft_pwm_0 < pwm_count) WRITE_HEATER_0(0); - #if EXTRUDERS > 1 + #if HOTENDS > 1 if (soft_pwm_1 < pwm_count) WRITE_HEATER_1(0); - #if EXTRUDERS > 2 + #if HOTENDS > 2 if (soft_pwm_2 < pwm_count) WRITE_HEATER_2(0); - #if EXTRUDERS > 3 + #if HOTENDS > 3 if (soft_pwm_3 < pwm_count) WRITE_HEATER_3(0); #endif #endif @@ -1524,11 +1524,11 @@ void Temperature::isr() { if (slow_pwm_count == 0) { SLOW_PWM_ROUTINE(0); // EXTRUDER 0 - #if EXTRUDERS > 1 + #if HOTENDS > 1 SLOW_PWM_ROUTINE(1); // EXTRUDER 1 - #if EXTRUDERS > 2 + #if HOTENDS > 2 SLOW_PWM_ROUTINE(2); // EXTRUDER 2 - #if EXTRUDERS > 3 + #if HOTENDS > 3 SLOW_PWM_ROUTINE(3); // EXTRUDER 3 #endif #endif @@ -1540,11 +1540,11 @@ void Temperature::isr() { } // slow_pwm_count == 0 PWM_OFF_ROUTINE(0); // EXTRUDER 0 - #if EXTRUDERS > 1 + #if HOTENDS > 1 PWM_OFF_ROUTINE(1); // EXTRUDER 1 - #if EXTRUDERS > 2 + #if HOTENDS > 2 PWM_OFF_ROUTINE(2); // EXTRUDER 2 - #if EXTRUDERS > 3 + #if HOTENDS > 3 PWM_OFF_ROUTINE(3); // EXTRUDER 3 #endif #endif @@ -1589,11 +1589,11 @@ void Temperature::isr() { // EXTRUDER 0 if (state_timer_heater_0 > 0) state_timer_heater_0--; - #if EXTRUDERS > 1 // EXTRUDER 1 + #if HOTENDS > 1 // EXTRUDER 1 if (state_timer_heater_1 > 0) state_timer_heater_1--; - #if EXTRUDERS > 2 // EXTRUDER 2 + #if HOTENDS > 2 // EXTRUDER 2 if (state_timer_heater_2 > 0) state_timer_heater_2--; - #if EXTRUDERS > 3 // EXTRUDER 3 + #if HOTENDS > 3 // EXTRUDER 3 if (state_timer_heater_3 > 0) state_timer_heater_3--; #endif #endif @@ -1736,7 +1736,7 @@ void Temperature::isr() { if (minttemp_raw[0] GE0 current_temperature_raw[0]) min_temp_error(0); #endif - #if HAS_TEMP_1 && EXTRUDERS > 1 + #if HAS_TEMP_1 && HOTENDS > 1 #if HEATER_1_RAW_LO_TEMP > HEATER_1_RAW_HI_TEMP #define GE1 <= #else @@ -1746,7 +1746,7 @@ void Temperature::isr() { if (minttemp_raw[1] GE1 current_temperature_raw[1]) min_temp_error(1); #endif // TEMP_SENSOR_1 - #if HAS_TEMP_2 && EXTRUDERS > 2 + #if HAS_TEMP_2 && HOTENDS > 2 #if HEATER_2_RAW_LO_TEMP > HEATER_2_RAW_HI_TEMP #define GE2 <= #else @@ -1756,7 +1756,7 @@ void Temperature::isr() { if (minttemp_raw[2] GE2 current_temperature_raw[2]) min_temp_error(2); #endif // TEMP_SENSOR_2 - #if HAS_TEMP_3 && EXTRUDERS > 3 + #if HAS_TEMP_3 && HOTENDS > 3 #if HEATER_3_RAW_LO_TEMP > HEATER_3_RAW_HI_TEMP #define GE3 <= #else diff --git a/Marlin/temperature.h b/Marlin/temperature.h index cb5710757..9cb990988 100644 --- a/Marlin/temperature.h +++ b/Marlin/temperature.h @@ -42,9 +42,9 @@ class Temperature { public: - static int current_temperature_raw[EXTRUDERS]; - static float current_temperature[EXTRUDERS]; - static int target_temperature[EXTRUDERS]; + static int current_temperature_raw[HOTENDS]; + static float current_temperature[HOTENDS]; + static int target_temperature[HOTENDS]; static int current_temperature_bed_raw; static float current_temperature_bed; @@ -66,11 +66,11 @@ class Temperature { #if ENABLED(PIDTEMP) - #if ENABLED(PID_PARAMS_PER_EXTRUDER) + #if ENABLED(PID_PARAMS_PER_HOTEND) - static float Kp[EXTRUDERS], Ki[EXTRUDERS], Kd[EXTRUDERS]; + static float Kp[HOTENDS], Ki[HOTENDS], Kd[HOTENDS]; #if ENABLED(PID_ADD_EXTRUSION_RATE) - static float Kc[EXTRUDERS]; + static float Kc[HOTENDS]; #endif #define PID_PARAM(param, e) Temperature::param[e] @@ -82,7 +82,7 @@ class Temperature { #endif #define PID_PARAM(param, e) Temperature::param - #endif // PID_PARAMS_PER_EXTRUDER + #endif // PID_PARAMS_PER_HOTEND // Apply the scale factors to the PID values #define scalePID_i(i) ( (i) * PID_dT ) @@ -101,8 +101,8 @@ class Temperature { #endif #if ENABLED(THERMAL_PROTECTION_HOTENDS) && WATCH_TEMP_PERIOD > 0 - static int watch_target_temp[EXTRUDERS]; - static millis_t watch_heater_next_ms[EXTRUDERS]; + static int watch_target_temp[HOTENDS]; + static millis_t watch_heater_next_ms[HOTENDS]; #endif #if ENABLED(THERMAL_PROTECTION_HOTENDS) && WATCH_BED_TEMP_PERIOD > 0 @@ -127,23 +127,23 @@ class Temperature { static volatile bool temp_meas_ready; #if ENABLED(PIDTEMP) - static float temp_iState[EXTRUDERS]; - static float temp_dState[EXTRUDERS]; - static float pTerm[EXTRUDERS]; - static float iTerm[EXTRUDERS]; - static float dTerm[EXTRUDERS]; + static float temp_iState[HOTENDS]; + static float temp_dState[HOTENDS]; + static float pTerm[HOTENDS]; + static float iTerm[HOTENDS]; + static float dTerm[HOTENDS]; #if ENABLED(PID_ADD_EXTRUSION_RATE) - static float cTerm[EXTRUDERS]; - static long last_position[EXTRUDERS]; + static float cTerm[HOTENDS]; + static long last_position[HOTENDS]; static long lpq[LPQ_MAX_LEN]; static int lpq_ptr; #endif - static float pid_error[EXTRUDERS]; - static float temp_iState_min[EXTRUDERS]; - static float temp_iState_max[EXTRUDERS]; - static bool pid_reset[EXTRUDERS]; + static float pid_error[HOTENDS]; + static float temp_iState_min[HOTENDS]; + static float temp_iState_max[HOTENDS]; + static bool pid_reset[HOTENDS]; #endif #if ENABLED(PIDTEMPBED) @@ -163,10 +163,10 @@ class Temperature { static unsigned long raw_temp_bed_value; // Init min and max temp with extreme values to prevent false errors during startup - static int minttemp_raw[EXTRUDERS]; - static int maxttemp_raw[EXTRUDERS]; - static int minttemp[EXTRUDERS]; - static int maxttemp[EXTRUDERS]; + static int minttemp_raw[HOTENDS]; + static int maxttemp_raw[HOTENDS]; + static int minttemp[HOTENDS]; + static int maxttemp[HOTENDS]; #ifdef BED_MINTEMP static int bed_minttemp_raw; @@ -184,7 +184,7 @@ class Temperature { static millis_t next_auto_fan_check_ms; #endif - static unsigned char soft_pwm[EXTRUDERS]; + static unsigned char soft_pwm[HOTENDS]; #if ENABLED(FAN_SOFT_PWM) static unsigned char soft_pwm_fan[FAN_COUNT]; @@ -230,15 +230,36 @@ class Temperature { //inline so that there is no performance decrease. //deg=degreeCelsius - static float degHotend(uint8_t extruder) { return current_temperature[extruder]; } + #if HOTENDS == 1 + #define HOTEND_ARG 0 + #else + #define HOTEND_ARG hotend + #endif + + static float degHotend(uint8_t hotend) { + #if HOTENDS == 1 + UNUSED(hotend); + #endif + return current_temperature[HOTEND_ARG]; + } static float degBed() { return current_temperature_bed; } #if ENABLED(SHOW_TEMP_ADC_VALUES) - static float rawHotendTemp(uint8_t extruder) { return current_temperature_raw[extruder]; } + static float rawHotendTemp(uint8_t hotend) { + #if HOTENDS == 1 + UNUSED(hotend); + #endif + return current_temperature_raw[HOTEND_ARG]; + } static float rawBedTemp() { return current_temperature_bed_raw; } #endif - static float degTargetHotend(uint8_t extruder) { return target_temperature[extruder]; } + static float degTargetHotend(uint8_t hotend) { + #if HOTENDS == 1 + UNUSED(hotend); + #endif + return target_temperature[HOTEND_ARG]; + } static float degTargetBed() { return target_temperature_bed; } #if ENABLED(THERMAL_PROTECTION_HOTENDS) && WATCH_TEMP_PERIOD > 0 @@ -249,10 +270,13 @@ class Temperature { static void start_watching_bed(); #endif - static void setTargetHotend(const float& celsius, uint8_t extruder) { - target_temperature[extruder] = celsius; + static void setTargetHotend(const float& celsius, uint8_t hotend) { + #if HOTENDS == 1 + UNUSED(hotend); + #endif + target_temperature[HOTEND_ARG] = celsius; #if ENABLED(THERMAL_PROTECTION_HOTENDS) && WATCH_TEMP_PERIOD > 0 - start_watching_heater(extruder); + start_watching_heater(HOTEND_ARG); #endif } @@ -263,10 +287,20 @@ class Temperature { #endif } - static bool isHeatingHotend(uint8_t extruder) { return target_temperature[extruder] > current_temperature[extruder]; } + static bool isHeatingHotend(uint8_t hotend) { + #if HOTENDS == 1 + UNUSED(hotend); + #endif + return target_temperature[HOTEND_ARG] > current_temperature[HOTEND_ARG]; + } static bool isHeatingBed() { return target_temperature_bed > current_temperature_bed; } - static bool isCoolingHotend(uint8_t extruder) { return target_temperature[extruder] < current_temperature[extruder]; } + static bool isCoolingHotend(uint8_t hotend) { + #if HOTENDS == 1 + UNUSED(hotend); + #endif + return target_temperature[HOTEND_ARG] < current_temperature[HOTEND_ARG]; + } static bool isCoolingBed() { return target_temperature_bed < current_temperature_bed; } /** @@ -283,7 +317,7 @@ class Temperature { * Perform auto-tuning for hotend or bed in response to M303 */ #if HAS_PID_HEATING - static void PID_autotune(float temp, int extruder, int ncycles, bool set_result=false); + static void PID_autotune(float temp, int hotend, int ncycles, bool set_result=false); #endif /** @@ -362,8 +396,8 @@ class Temperature { static void thermal_runaway_protection(TRState* state, millis_t* timer, float temperature, float target_temperature, int heater_id, int period_seconds, int hysteresis_degc); #if ENABLED(THERMAL_PROTECTION_HOTENDS) - static TRState thermal_runaway_state_machine[EXTRUDERS]; - static millis_t thermal_runaway_timer[EXTRUDERS]; + static TRState thermal_runaway_state_machine[HOTENDS]; + static millis_t thermal_runaway_timer[HOTENDS]; #endif #if HAS_THERMALLY_PROTECTED_BED diff --git a/Marlin/ultralcd.cpp b/Marlin/ultralcd.cpp index 94a1e3f75..cb5f6d68a 100644 --- a/Marlin/ultralcd.cpp +++ b/Marlin/ultralcd.cpp @@ -593,28 +593,28 @@ void lcd_set_home_offsets() { #if TEMP_SENSOR_0 != 0 void watch_temp_callback_E0() { thermalManager.start_watching_heater(0); } #endif - #if EXTRUDERS > 1 && TEMP_SENSOR_1 != 0 + #if HOTENDS > 1 && TEMP_SENSOR_1 != 0 void watch_temp_callback_E1() { thermalManager.start_watching_heater(1); } - #endif // EXTRUDERS > 1 - #if EXTRUDERS > 2 && TEMP_SENSOR_2 != 0 + #endif // HOTENDS > 1 + #if HOTENDS > 2 && TEMP_SENSOR_2 != 0 void watch_temp_callback_E2() { thermalManager.start_watching_heater(2); } - #endif // EXTRUDERS > 2 - #if EXTRUDERS > 3 && TEMP_SENSOR_3 != 0 + #endif // HOTENDS > 2 + #if HOTENDS > 3 && TEMP_SENSOR_3 != 0 void watch_temp_callback_E3() { thermalManager.start_watching_heater(3); } - #endif // EXTRUDERS > 3 + #endif // HOTENDS > 3 #else #if TEMP_SENSOR_0 != 0 void watch_temp_callback_E0() {} #endif - #if EXTRUDERS > 1 && TEMP_SENSOR_1 != 0 + #if HOTENDS > 1 && TEMP_SENSOR_1 != 0 void watch_temp_callback_E1() {} - #endif // EXTRUDERS > 1 - #if EXTRUDERS > 2 && TEMP_SENSOR_2 != 0 + #endif // HOTENDS > 1 + #if HOTENDS > 2 && TEMP_SENSOR_2 != 0 void watch_temp_callback_E2() {} - #endif // EXTRUDERS > 2 - #if EXTRUDERS > 3 && TEMP_SENSOR_3 != 0 + #endif // HOTENDS > 2 + #if HOTENDS > 3 && TEMP_SENSOR_3 != 0 void watch_temp_callback_E3() {} - #endif // EXTRUDERS > 3 + #endif // HOTENDS > 3 #endif #if ENABLED(THERMAL_PROTECTION_BED) && WATCH_BED_TEMP_PERIOD > 0 @@ -654,28 +654,28 @@ static void lcd_tune_menu() { // Nozzle: // Nozzle [1-4]: // - #if EXTRUDERS == 1 + #if HOTENDS == 1 #if TEMP_SENSOR_0 != 0 MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE, &thermalManager.target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0); #endif - #else //EXTRUDERS > 1 + #else //HOTENDS > 1 #if TEMP_SENSOR_0 != 0 MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N1, &thermalManager.target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0); #endif #if TEMP_SENSOR_1 != 0 MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N2, &thermalManager.target_temperature[1], 0, HEATER_1_MAXTEMP - 15, watch_temp_callback_E1); #endif - #if EXTRUDERS > 2 + #if HOTENDS > 2 #if TEMP_SENSOR_2 != 0 MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N3, &thermalManager.target_temperature[2], 0, HEATER_2_MAXTEMP - 15, watch_temp_callback_E2); #endif - #if EXTRUDERS > 3 + #if HOTENDS > 3 #if TEMP_SENSOR_3 != 0 MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N4, &thermalManager.target_temperature[3], 0, HEATER_3_MAXTEMP - 15, watch_temp_callback_E3); #endif - #endif // EXTRUDERS > 3 - #endif // EXTRUDERS > 2 - #endif // EXTRUDERS > 1 + #endif // HOTENDS > 3 + #endif // HOTENDS > 2 + #endif // HOTENDS > 1 // // Bed: @@ -777,24 +777,24 @@ void _lcd_preheat(int endnum, const float temph, const float tempb, const int fa void lcd_preheat_abs0() { _lcd_preheat(0, absPreheatHotendTemp, absPreheatHPBTemp, absPreheatFanSpeed); } #endif -#if EXTRUDERS > 1 +#if HOTENDS > 1 void lcd_preheat_pla1() { _lcd_preheat(1, plaPreheatHotendTemp, plaPreheatHPBTemp, plaPreheatFanSpeed); } void lcd_preheat_abs1() { _lcd_preheat(1, absPreheatHotendTemp, absPreheatHPBTemp, absPreheatFanSpeed); } - #if EXTRUDERS > 2 + #if HOTENDS > 2 void lcd_preheat_pla2() { _lcd_preheat(2, plaPreheatHotendTemp, plaPreheatHPBTemp, plaPreheatFanSpeed); } void lcd_preheat_abs2() { _lcd_preheat(2, absPreheatHotendTemp, absPreheatHPBTemp, absPreheatFanSpeed); } - #if EXTRUDERS > 3 + #if HOTENDS > 3 void lcd_preheat_pla3() { _lcd_preheat(3, plaPreheatHotendTemp, plaPreheatHPBTemp, plaPreheatFanSpeed); } void lcd_preheat_abs3() { _lcd_preheat(3, absPreheatHotendTemp, absPreheatHPBTemp, absPreheatFanSpeed); } #endif #endif void lcd_preheat_pla0123() { - #if EXTRUDERS > 1 + #if HOTENDS > 1 thermalManager.setTargetHotend(plaPreheatHotendTemp, 1); - #if EXTRUDERS > 2 + #if HOTENDS > 2 thermalManager.setTargetHotend(plaPreheatHotendTemp, 2); - #if EXTRUDERS > 3 + #if HOTENDS > 3 thermalManager.setTargetHotend(plaPreheatHotendTemp, 3); #endif #endif @@ -802,11 +802,11 @@ void _lcd_preheat(int endnum, const float temph, const float tempb, const int fa lcd_preheat_pla0(); } void lcd_preheat_abs0123() { - #if EXTRUDERS > 1 + #if HOTENDS > 1 thermalManager.setTargetHotend(absPreheatHotendTemp, 1); - #if EXTRUDERS > 2 + #if HOTENDS > 2 thermalManager.setTargetHotend(absPreheatHotendTemp, 2); - #if EXTRUDERS > 3 + #if HOTENDS > 3 thermalManager.setTargetHotend(absPreheatHotendTemp, 3); #endif #endif @@ -814,7 +814,7 @@ void _lcd_preheat(int endnum, const float temph, const float tempb, const int fa lcd_preheat_abs0(); } -#endif // EXTRUDERS > 1 +#endif // HOTENDS > 1 #if TEMP_SENSOR_BED != 0 void lcd_preheat_pla_bedonly() { _lcd_preheat(0, 0, plaPreheatHPBTemp, plaPreheatFanSpeed); } @@ -826,14 +826,14 @@ void _lcd_preheat(int endnum, const float temph, const float tempb, const int fa static void lcd_preheat_pla_menu() { START_MENU(); MENU_ITEM(back, MSG_PREPARE); - #if EXTRUDERS == 1 + #if HOTENDS == 1 MENU_ITEM(function, MSG_PREHEAT_PLA, lcd_preheat_pla0); #else MENU_ITEM(function, MSG_PREHEAT_PLA_N MSG_H1, lcd_preheat_pla0); MENU_ITEM(function, MSG_PREHEAT_PLA_N MSG_H2, lcd_preheat_pla1); - #if EXTRUDERS > 2 + #if HOTENDS > 2 MENU_ITEM(function, MSG_PREHEAT_PLA_N MSG_H3, lcd_preheat_pla2); - #if EXTRUDERS > 3 + #if HOTENDS > 3 MENU_ITEM(function, MSG_PREHEAT_PLA_N MSG_H4, lcd_preheat_pla3); #endif #endif @@ -848,14 +848,14 @@ void _lcd_preheat(int endnum, const float temph, const float tempb, const int fa static void lcd_preheat_abs_menu() { START_MENU(); MENU_ITEM(back, MSG_PREPARE); - #if EXTRUDERS == 1 + #if HOTENDS == 1 MENU_ITEM(function, MSG_PREHEAT_ABS, lcd_preheat_abs0); #else MENU_ITEM(function, MSG_PREHEAT_ABS_N MSG_H1, lcd_preheat_abs0); MENU_ITEM(function, MSG_PREHEAT_ABS_N MSG_H2, lcd_preheat_abs1); - #if EXTRUDERS > 2 + #if HOTENDS > 2 MENU_ITEM(function, MSG_PREHEAT_ABS_N MSG_H3, lcd_preheat_abs2); - #if EXTRUDERS > 3 + #if HOTENDS > 3 MENU_ITEM(function, MSG_PREHEAT_ABS_N MSG_H4, lcd_preheat_abs3); #endif #endif @@ -1380,8 +1380,8 @@ static void lcd_control_menu() { #if ENABLED(PID_AUTOTUNE_MENU) #if ENABLED(PIDTEMP) - int autotune_temp[EXTRUDERS] = ARRAY_BY_EXTRUDERS1(150); - const int heater_maxtemp[EXTRUDERS] = ARRAY_BY_EXTRUDERS(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP); + int autotune_temp[HOTENDS] = ARRAY_BY_HOTENDS1(150); + const int heater_maxtemp[HOTENDS] = ARRAY_BY_HOTENDS(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP); #endif #if ENABLED(PIDTEMPBED) @@ -1409,14 +1409,14 @@ static void lcd_control_menu() { // Helpers for editing PID Ki & Kd values // grab the PID value out of the temp variable; scale it; then update the PID driver void copy_and_scalePID_i(int e) { - #if DISABLED(PID_PARAMS_PER_EXTRUDER) + #if DISABLED(PID_PARAMS_PER_HOTEND) UNUSED(e); #endif PID_PARAM(Ki, e) = scalePID_i(raw_Ki); thermalManager.updatePID(); } void copy_and_scalePID_d(int e) { - #if DISABLED(PID_PARAMS_PER_EXTRUDER) + #if DISABLED(PID_PARAMS_PER_HOTEND) UNUSED(e); #endif PID_PARAM(Kd, e) = scalePID_d(raw_Kd); @@ -1435,17 +1435,17 @@ static void lcd_control_menu() { #endif _PIDTEMP_FUNCTIONS(0); - #if ENABLED(PID_PARAMS_PER_EXTRUDER) - #if EXTRUDERS > 1 + #if ENABLED(PID_PARAMS_PER_HOTEND) + #if HOTENDS > 1 _PIDTEMP_FUNCTIONS(1); - #if EXTRUDERS > 2 + #if HOTENDS > 2 _PIDTEMP_FUNCTIONS(2); - #if EXTRUDERS > 3 + #if HOTENDS > 3 _PIDTEMP_FUNCTIONS(3); - #endif //EXTRUDERS > 3 - #endif //EXTRUDERS > 2 - #endif //EXTRUDERS > 1 - #endif //PID_PARAMS_PER_EXTRUDER + #endif //HOTENDS > 3 + #endif //HOTENDS > 2 + #endif //HOTENDS > 1 + #endif //PID_PARAMS_PER_HOTEND #endif //PIDTEMP @@ -1466,28 +1466,28 @@ static void lcd_control_temperature_menu() { // Nozzle: // Nozzle [1-4]: // - #if EXTRUDERS == 1 + #if HOTENDS == 1 #if TEMP_SENSOR_0 != 0 MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE, &thermalManager.target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0); #endif - #else //EXTRUDERS > 1 + #else //HOTENDS > 1 #if TEMP_SENSOR_0 != 0 MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N1, &thermalManager.target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0); #endif #if TEMP_SENSOR_1 != 0 MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N2, &thermalManager.target_temperature[1], 0, HEATER_1_MAXTEMP - 15, watch_temp_callback_E1); #endif - #if EXTRUDERS > 2 + #if HOTENDS > 2 #if TEMP_SENSOR_2 != 0 MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N3, &thermalManager.target_temperature[2], 0, HEATER_2_MAXTEMP - 15, watch_temp_callback_E2); #endif - #if EXTRUDERS > 3 + #if HOTENDS > 3 #if TEMP_SENSOR_3 != 0 MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_N4, &thermalManager.target_temperature[3], 0, HEATER_3_MAXTEMP - 15, watch_temp_callback_E3); #endif - #endif // EXTRUDERS > 3 - #endif // EXTRUDERS > 2 - #endif // EXTRUDERS > 1 + #endif // HOTENDS > 3 + #endif // HOTENDS > 2 + #endif // HOTENDS > 1 // // Bed: @@ -1558,18 +1558,18 @@ static void lcd_control_temperature_menu() { #define PID_MENU_ITEMS(ELABEL, eindex) _PID_MENU_ITEMS(ELABEL, eindex) #endif - #if ENABLED(PID_PARAMS_PER_EXTRUDER) && EXTRUDERS > 1 + #if ENABLED(PID_PARAMS_PER_HOTEND) && HOTENDS > 1 PID_MENU_ITEMS(MSG_E1, 0); PID_MENU_ITEMS(MSG_E2, 1); - #if EXTRUDERS > 2 + #if HOTENDS > 2 PID_MENU_ITEMS(MSG_E3, 2); - #if EXTRUDERS > 3 + #if HOTENDS > 3 PID_MENU_ITEMS(MSG_E4, 3); - #endif //EXTRUDERS > 3 - #endif //EXTRUDERS > 2 - #else //!PID_PARAMS_PER_EXTRUDER || EXTRUDERS == 1 + #endif //HOTENDS > 3 + #endif //HOTENDS > 2 + #else //!PID_PARAMS_PER_HOTEND || HOTENDS == 1 PID_MENU_ITEMS("", 0); - #endif //!PID_PARAMS_PER_EXTRUDER || EXTRUDERS == 1 + #endif //!PID_PARAMS_PER_HOTEND || HOTENDS == 1 #endif //PIDTEMP diff --git a/Marlin/ultralcd_implementation_hitachi_HD44780.h b/Marlin/ultralcd_implementation_hitachi_HD44780.h index 05afe59a3..61e9a62ee 100644 --- a/Marlin/ultralcd_implementation_hitachi_HD44780.h +++ b/Marlin/ultralcd_implementation_hitachi_HD44780.h @@ -638,10 +638,10 @@ static void lcd_implementation_status_screen() { // // Hotend 1 or Bed Temperature // - #if EXTRUDERS > 1 || TEMP_SENSOR_BED != 0 + #if HOTENDS > 1 || TEMP_SENSOR_BED != 0 lcd.setCursor(8, 0); - #if EXTRUDERS > 1 + #if HOTENDS > 1 lcd.print(LCD_STR_THERMOMETER[0]); LCD_TEMP_ONLY(thermalManager.degHotend(1), thermalManager.degTargetHotend(1)); #else @@ -649,7 +649,7 @@ static void lcd_implementation_status_screen() { LCD_TEMP_ONLY(thermalManager.degBed(), thermalManager.degTargetBed()); #endif - #endif // EXTRUDERS > 1 || TEMP_SENSOR_BED != 0 + #endif // HOTENDS > 1 || TEMP_SENSOR_BED != 0 #else // LCD_WIDTH >= 20 @@ -661,15 +661,15 @@ static void lcd_implementation_status_screen() { // // Hotend 1 or Bed Temperature // - #if EXTRUDERS > 1 || TEMP_SENSOR_BED != 0 + #if HOTENDS > 1 || TEMP_SENSOR_BED != 0 lcd.setCursor(10, 0); - #if EXTRUDERS > 1 + #if HOTENDS > 1 LCD_TEMP(thermalManager.degHotend(1), thermalManager.degTargetHotend(1), LCD_STR_THERMOMETER[0]); #else LCD_TEMP(thermalManager.degBed(), thermalManager.degTargetBed(), LCD_STR_BEDTEMP[0]); #endif - #endif // EXTRUDERS > 1 || TEMP_SENSOR_BED != 0 + #endif // HOTENDS > 1 || TEMP_SENSOR_BED != 0 #endif // LCD_WIDTH >= 20 @@ -697,7 +697,7 @@ static void lcd_implementation_status_screen() { lcd.setCursor(0, 1); - #if EXTRUDERS > 1 && TEMP_SENSOR_BED != 0 + #if HOTENDS > 1 && TEMP_SENSOR_BED != 0 // If we both have a 2nd extruder and a heated bed, // show the heated bed temp on the left, @@ -717,7 +717,7 @@ static void lcd_implementation_status_screen() { _draw_axis_label(Y_AXIS, PSTR(MSG_Y), blink); lcd.print(ftostr4sign(current_position[Y_AXIS])); - #endif // EXTRUDERS > 1 || TEMP_SENSOR_BED != 0 + #endif // HOTENDS > 1 || TEMP_SENSOR_BED != 0 #endif // LCD_WIDTH >= 20 @@ -943,7 +943,7 @@ void lcd_implementation_drawedit(const char* pstr, const char* value=NULL) { ) leds |= LED_C; #endif // FAN_COUNT > 0 - #if EXTRUDERS > 1 + #if HOTENDS > 1 if (thermalManager.degTargetHotend(1) > 0) leds |= LED_C; #endif