Merge pull request #4894 from thinkyhead/rc_mightyboard_rev_e

Mightyboard Revision E preliminary support
master
Scott Lahteine 8 years ago committed by GitHub
commit d567b426d5

@ -33,6 +33,7 @@
#define BOARD_CNCONTROLS_12 112 // Cartesio CN Controls V12
#define BOARD_CHEAPTRONIC 2 // Cheaptronic v1.0
#define BOARD_SETHI 20 // Sethi 3D_1
#define BOARD_MIGHTYBOARD_REVE 200 // Makerbot Mightyboard Revision E
#define BOARD_RAMPS_OLD 3 // MEGA/RAMPS up to 1.2
#define BOARD_RAMPS_13_EFB 33 // RAMPS 1.3 (Power outputs: Hotend, Fan, Bed)
#define BOARD_RAMPS_13_EEB 34 // RAMPS 1.3 (Power outputs: Hotend0, Hotend1, Bed)

@ -1835,18 +1835,6 @@
#define PG5_WPORT PORTG
#define PG5_DDR DDRG
#define PG5_PWM &OCR0B
#undef PG6
#define PG6_PIN PING6
#define PG6_RPORT PING
#define PG6_WPORT PORTG
#define PG6_DDR DDRG
#define PG6_PWM NULL
#undef PG7
#define PG7_PIN PING7
#define PG7_RPORT PING
#define PG7_WPORT PORTG
#define PG7_DDR DDRG
#define PG7_PWM NULL
#undef PH0
#define PH0_PIN PINH0

@ -39,6 +39,8 @@
#include "pins_CHEAPTRONIC.h"
#elif MB(SETHI)
#include "pins_SETHI.h"
#elif MB(MIGHTYBOARD_REVE)
#include "pins_MIGHTYBOARD_REVE.h"
#elif MB(RAMPS_OLD)
#include "pins_RAMPS_OLD.h"
#elif MB(RAMPS_13_EFB)

@ -0,0 +1,205 @@
/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Mightyboard Rev.E pin assignments
*/
#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
#error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
#endif
#define DEFAULT_MACHINE_NAME "MB Replicator"
#define BOARD_NAME "Mightyboard"
#define LARGE_FLASH true
//
// Servos
//
#define SERVO0_PIN 36 // C1 (1280-EX1)
#define SERVO1_PIN 37 // C0 (1280-EX2)
#define SERVO2_PIN 40 // G1 (1280-EX3)
#define SERVO3_PIN 41 // G0 (1280-EX4)
//
// Limit Switches
//
#define X_MIN_PIN 49 // L0
#define X_MAX_PIN 48 // L1
#define Y_MIN_PIN 47 // L2
#define Y_MAX_PIN 46 // L3
#define Z_MIN_PIN 43 // L6
#define Z_MAX_PIN 42 // L7
//
// Z Probe (when not Z_MIN_PIN)
//
#ifndef Z_MIN_PROBE_PIN
#define Z_MIN_PROBE_PIN 42
#endif
//
// Steppers
//
#define X_STEP_PIN 55 // F1
#define X_DIR_PIN 54 // F0
#define X_ENABLE_PIN 56 // F2
#define Y_STEP_PIN 59 // F5
#define Y_DIR_PIN 58 // F4
#define Y_ENABLE_PIN 60 // F6
#define Z_STEP_PIN 63 // K1
#define Z_DIR_PIN 62 // K0
#define Z_ENABLE_PIN 64 // K2
#define E0_STEP_PIN 25 // A3
#define E0_DIR_PIN 24 // A2
#define E0_ENABLE_PIN 26 // A4
#define E1_STEP_PIN 29 // A7
#define E1_DIR_PIN 28 // A6
#define E1_ENABLE_PIN 39 // G2
//
// I2C Digipots - MCP4018
// Address 5E (2F << 1)
// Set from 0 - 127 with stop bit.
// (Ex. 3F << 1 | 1)
//
#define DIGIPOTS_I2C_SCL 76 // J5
#define DIGIPOTS_I2C_SDA_X 57 // F3
#define DIGIPOTS_I2C_SDA_Y 61 // F7
#define DIGIPOTS_I2C_SDA_Z 65 // K3
#define DIGIPOTS_I2C_SDA_E0 27 // A5
#define DIGIPOTS_I2C_SDA_E1 77 // J6
//
// Temperature Sensors
//
#define TEMP_BED_PIN 69 // K7
// SPI for Max6675 or Max31855 Thermocouple
// Uses a separate SPI bus
//
// 3 E5 DO (SO)
// 5 E3 CS1
// 2 E4 CS2
// 78 E2 SCK
//
#define THERMO_SCK_PIN 78 // E2
#define THERMO_DO_PIN 3 // E5
#define THERMO_CS1 5 // E3
#define THERMO_CS2 2 // E4
//
// Augmentation for auto-assigning plugs
//
// Two thermocouple connectors allows for either
// 2 extruders or 1 extruder and a heated bed.
// With no heated bed, an additional 24V fan is possible.
//
#define MOSFET_A_PIN 6 // H3
#define MOSFET_B_PIN 9 // B5
#define MOSFET_C_PIN 45 // L4
#define MOSFET_D_PIN 44 // L5
#if HOTENDS > 1
#if TEMP_SENSOR_BED
#define IS_EEB
#else
#define IS_EEF
#endif
#elif TEMP_SENSOR_BED
#define IS_EFB
#else
#define IS_EFF
#endif
//
// Heaters / Fans (24V)
//
#define HEATER_0_PIN MOSFET_A_PIN
#if ENABLED(IS_EFB) // Hotend, Fan, Bed
#define FAN_PIN MOSFET_B_PIN
#define HEATER_BED_PIN MOSFET_C_PIN
#elif ENABLED(IS_EEF) // Hotend, Hotend, Fan
#define HEATER_1_PIN MOSFET_B_PIN
#define FAN_PIN MOSFET_C_PIN
#elif ENABLED(IS_EEB) // Hotend, Hotend, Bed
#define HEATER_1_PIN MOSFET_B_PIN
#define HEATER_BED_PIN MOSFET_C_PIN
#elif ENABLED(IS_EFF) // Hotend, Fan, Fan
#define FAN_PIN MOSFET_B_PIN
#define FAN1_PIN MOSFET_C_PIN
#elif ENABLED(IS_SF) // Spindle, Fan
#define FAN_PIN MOSFET_C_PIN
#endif
#ifndef FAN_PIN
#define FAN_PIN MOSFET_D_PIN
#endif
//
// Extruder Auto Fan Pins
//
#define EXTRUDER_0_AUTO_FAN 7 // H4
#define EXTRUDER_1_AUTO_FAN 12 // B6
//
// Misc. Functions
//
#define LED_PIN 13 // B7
#define CUTOFF_RESET_PIN 16 // H1
#define CUTOFF_TEST_PIN 17 // H0
//
// LCD / Controller
//
// Replicator uses a 3-wire SR controller with HD44780
// For now, pretend it's the SAV
//
#define SAV_3DLCD
#define SR_DATA_PIN 34 // C3
#define SR_CLK_PIN 35 // C2
#define SR_STROBE_PIN 33 // C4
#define BTN_UP 75 // J4
#define BTN_DOWN 73 // J3
#define BTN_LEFT 72 // J2
#define BTN_RIGHT 14 // J1
#define BTN_CENTER 15 // J0
#define BTN_ENC BTN_CENTER
#define BEEPER_PIN 4 // G5
#define STAT_LED_RED 32 // C5
#define STAT_LED_BLUE 31 // C6 (Actually green)
//
// SD Card
//
#define SDSS 53 // B0
#define SD_DETECT_PIN 30 // C7

@ -161,7 +161,11 @@ extern volatile uint8_t buttons; //an extended version of the last checked butt
#include <LCD.h>
#include <LiquidCrystal_SR.h>
#define LCD_CLASS LiquidCrystal_SR
LCD_CLASS lcd(SR_DATA_PIN, SR_CLK_PIN);
#if defined(SR_STROBE_PIN)
LCD_CLASS lcd(SR_DATA_PIN, SR_CLK_PIN, SR_STROBE_PIN);
#else
LCD_CLASS lcd(SR_DATA_PIN, SR_CLK_PIN);
#endif
#elif ENABLED(LCM1602)
#include <Wire.h>
#include <LCD.h>

Loading…
Cancel
Save