diff --git a/Marlin/configurator/config/Configuration.h b/Marlin/configurator/config/Configuration.h index e4028295b..9ecbdb8f3 100644 --- a/Marlin/configurator/config/Configuration.h +++ b/Marlin/configurator/config/Configuration.h @@ -205,21 +205,22 @@ Here are some standard links for getting your machine calibrated: #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term #define K1 0.95 //smoothing factor within the PID -// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it -// Ultimaker - #define DEFAULT_Kp 22.2 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114 - -// MakerGear -// #define DEFAULT_Kp 7.0 -// #define DEFAULT_Ki 0.1 -// #define DEFAULT_Kd 12 - -// Mendel Parts V9 on 12V -// #define DEFAULT_Kp 63.0 -// #define DEFAULT_Ki 2.25 -// #define DEFAULT_Kd 440 + // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it + // Ultimaker + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 + + // MakerGear + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 + + // Mendel Parts V9 on 12V + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 + #endif // PIDTEMP //=========================================================================== diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h index d1d68b29a..791e5b0e1 100644 --- a/Marlin/example_configurations/Hephestos/Configuration.h +++ b/Marlin/example_configurations/Hephestos/Configuration.h @@ -208,23 +208,7 @@ Here are some standard links for getting your machine calibrated: #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term #define K1 0.95 //smoothing factor within the PID - // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it - // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 - - // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 - - // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 - - // Hephestos (i3) + // Hephestos i3 #define DEFAULT_Kp 23.05 #define DEFAULT_Ki 2.00 #define DEFAULT_Kd 66.47 diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h index 935b2b412..48b67d9ab 100644 --- a/Marlin/example_configurations/K8200/Configuration.h +++ b/Marlin/example_configurations/K8200/Configuration.h @@ -210,22 +210,6 @@ Here are some standard links for getting your machine calibrated: #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term #define K1 0.95 //smoothing factor within the PID - // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it - // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 - - // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 - - // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 - // Vellemann K8200 Extruder - calculated with PID Autotune and tested #define DEFAULT_Kp 24.29 #define DEFAULT_Ki 1.58 @@ -261,18 +245,6 @@ Here are some standard links for getting your machine calibrated: #define PID_BED_INTEGRAL_DRIVE_MAX MAX_BED_POWER //limit for the integral term - //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) - //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - //#define DEFAULT_bedKp 10.00 - //#define DEFAULT_bedKi .023 - //#define DEFAULT_bedKd 305.4 - - //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) - //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 - //Vellemann K8200 PCB heatbed with standard PCU at 60 degreesC - calculated with PID Autotune and tested //from pidautotune #define DEFAULT_bedKp 341.88 diff --git a/Marlin/example_configurations/RigidBot/Configuration.h b/Marlin/example_configurations/RigidBot/Configuration.h index d2aa4cb2c..7c2d7f25b 100644 --- a/Marlin/example_configurations/RigidBot/Configuration.h +++ b/Marlin/example_configurations/RigidBot/Configuration.h @@ -211,16 +211,6 @@ Here are some standard links for getting your machine calibrated: #define DEFAULT_Ki 4.21 //Base DGlass3D/E3Dv6 = 0.85 ; RigidBot redesigned = 0.85 #define DEFAULT_Kd 88.41 //Base DGlass3D/E3Dv6 = 245 ; RigidBot redesigned = 76.55 - // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 - - // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 - #endif // PIDTEMP //=========================================================================== @@ -256,12 +246,6 @@ Here are some standard links for getting your machine calibrated: #define DEFAULT_bedKi 66.5 #define DEFAULT_bedKd 480 - //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) - //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 - // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h index 9996a7120..552540cf1 100644 --- a/Marlin/example_configurations/SCARA/Configuration.h +++ b/Marlin/example_configurations/SCARA/Configuration.h @@ -230,27 +230,6 @@ Here are some standard links for getting your machine calibrated: #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term #define K1 0.95 //smoothing factor within the PID - // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it - // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 - - // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 - - // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 - - // Jhead MK5: From Autotune - //#define DEFAULT_Kp 20.92 - //#define DEFAULT_Ki 1.51 - //#define DEFAULT_Kd 72.34 - // Merlin Hotend: From Autotune #define DEFAULT_Kp 24.5 #define DEFAULT_Ki 1.72 @@ -286,18 +265,6 @@ Here are some standard links for getting your machine calibrated: #define PID_BED_INTEGRAL_DRIVE_MAX MAX_BED_POWER //limit for the integral term - //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) - //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - //#define DEFAULT_bedKp 10.00 - //#define DEFAULT_bedKi .023 - //#define DEFAULT_bedKd 305.4 - - //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) - //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 - //12v Heatbed Mk3 12V in parallel //from pidautotune #define DEFAULT_bedKp 630.14 diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h index c59a6276b..c9ddf8410 100644 --- a/Marlin/example_configurations/WITBOX/Configuration.h +++ b/Marlin/example_configurations/WITBOX/Configuration.h @@ -208,22 +208,6 @@ Here are some standard links for getting your machine calibrated: #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term #define K1 0.95 //smoothing factor within the PID - // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it - // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 - - // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 - - // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 - // Witbox #define DEFAULT_Kp 22.2 #define DEFAULT_Ki 1.08 diff --git a/Marlin/example_configurations/adafruit/ST7565/Configuration.h b/Marlin/example_configurations/adafruit/ST7565/Configuration.h index 165a6bd10..c7ef630e6 100644 --- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h +++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h @@ -205,21 +205,22 @@ Here are some standard links for getting your machine calibrated: #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term #define K1 0.95 //smoothing factor within the PID -// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it -// Ultimaker - #define DEFAULT_Kp 22.2 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114 - -// MakerGear -// #define DEFAULT_Kp 7.0 -// #define DEFAULT_Ki 0.1 -// #define DEFAULT_Kd 12 - -// Mendel Parts V9 on 12V -// #define DEFAULT_Kp 63.0 -// #define DEFAULT_Ki 2.25 -// #define DEFAULT_Kd 440 + // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it + // Ultimaker + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 + + // MakerGear + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 + + // Mendel Parts V9 on 12V + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 + #endif // PIDTEMP //=========================================================================== diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration.h b/Marlin/example_configurations/delta/kossel_pro/Configuration.h index b3d9bf180..302d234e0 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h @@ -209,27 +209,11 @@ Here are some standard links for getting your machine calibrated: #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term #define K1 0.95 //smoothing factor within the PID - // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it - // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 - // Kossel Pro #define DEFAULT_Kp 19.30 #define DEFAULT_Ki 3.51 #define DEFAULT_Kd 26.56 - // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 - - // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 - #endif // PIDTEMP //=========================================================================== @@ -266,18 +250,6 @@ Here are some standard links for getting your machine calibrated: #define DEFAULT_bedKi 62.77 #define DEFAULT_bedKd 545.98 - //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) - //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - //#define DEFAULT_bedKp 10.00 - //#define DEFAULT_bedKi .023 - //#define DEFAULT_bedKd 305.4 - - //120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) - //from pidautotune - //#define DEFAULT_bedKp 97.1 - //#define DEFAULT_bedKi 1.41 - //#define DEFAULT_bedKd 1675.16 - // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h index c266d0abf..4bfc6e284 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h @@ -211,21 +211,6 @@ Here are some standard links for getting your machine calibrated: #define DEFAULT_Ki 2.30 #define DEFAULT_Kd 68.15 - // Ultimaker - //#define DEFAULT_Kp 22.2 - //#define DEFAULT_Ki 1.08 - //#define DEFAULT_Kd 114 - - // MakerGear - //#define DEFAULT_Kp 7.0 - //#define DEFAULT_Ki 0.1 - //#define DEFAULT_Kd 12 - - // Mendel Parts V9 on 12V - //#define DEFAULT_Kp 63.0 - //#define DEFAULT_Ki 2.25 - //#define DEFAULT_Kd 440 - #endif // PIDTEMP //===========================================================================