diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index d137169d1..8b3edfc71 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -47,22 +47,19 @@ #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control /** - * Thermal Protection parameters + * Thermal Protection protects your printer from damage and fire if a + * thermistor falls out or temperature sensors fail in any way. + * + * The issue: If a thermistor falls out or a temperature sensor fails, + * Marlin can no longer sense the actual temperature. Since a disconnected + * thermistor reads as a low temperature, the firmware will keep the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too long (period), + * the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD */ - /** - * Thermal Protection protects your printer from damage and fire if a - * thermistor falls out or temperature sensors fail in any way. - * - * The issue: If a thermistor falls out or a temperature sensor fails, - * Marlin can no longer sense the actual temperature. Since a disconnected - * thermistor reads as a low temperature, the firmware will keep the heater on. - * - * The solution: Once the temperature reaches the target, start observing. - * If the temperature stays too far below the target (hysteresis) for too long (period), - * the firmware will halt the machine as a safety precaution. - * - * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD - */ #if ENABLED(THERMAL_PROTECTION_HOTENDS) #define THERMAL_PROTECTION_PERIOD 40 // Seconds #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius @@ -80,11 +77,11 @@ #define WATCH_TEMP_INCREASE 4 // Degrees Celsius #endif - /** - * Thermal Protection parameters for the bed - * are like the above for the hotends. - * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. - */ +/** + * Thermal Protection parameters for the bed + * are like the above for the hotends. + * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. + */ #if ENABLED(THERMAL_PROTECTION_BED) #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius diff --git a/Marlin/example_configurations/Felix/Configuration_adv.h b/Marlin/example_configurations/Felix/Configuration_adv.h index 216d16415..54f6421e3 100644 --- a/Marlin/example_configurations/Felix/Configuration_adv.h +++ b/Marlin/example_configurations/Felix/Configuration_adv.h @@ -47,22 +47,19 @@ #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control /** - * Thermal Protection parameters + * Thermal Protection protects your printer from damage and fire if a + * thermistor falls out or temperature sensors fail in any way. + * + * The issue: If a thermistor falls out or a temperature sensor fails, + * Marlin can no longer sense the actual temperature. Since a disconnected + * thermistor reads as a low temperature, the firmware will keep the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too long (period), + * the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD */ - /** - * Thermal Protection protects your printer from damage and fire if a - * thermistor falls out or temperature sensors fail in any way. - * - * The issue: If a thermistor falls out or a temperature sensor fails, - * Marlin can no longer sense the actual temperature. Since a disconnected - * thermistor reads as a low temperature, the firmware will keep the heater on. - * - * The solution: Once the temperature reaches the target, start observing. - * If the temperature stays too far below the target (hysteresis) for too long (period), - * the firmware will halt the machine as a safety precaution. - * - * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD - */ #if ENABLED(THERMAL_PROTECTION_HOTENDS) #define THERMAL_PROTECTION_PERIOD 40 // Seconds #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius @@ -80,11 +77,11 @@ #define WATCH_TEMP_INCREASE 4 // Degrees Celsius #endif - /** - * Thermal Protection parameters for the bed - * are like the above for the hotends. - * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. - */ +/** + * Thermal Protection parameters for the bed + * are like the above for the hotends. + * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. + */ #if ENABLED(THERMAL_PROTECTION_BED) #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius diff --git a/Marlin/example_configurations/Hephestos/Configuration_adv.h b/Marlin/example_configurations/Hephestos/Configuration_adv.h index 2bd84d0b4..603a39a48 100644 --- a/Marlin/example_configurations/Hephestos/Configuration_adv.h +++ b/Marlin/example_configurations/Hephestos/Configuration_adv.h @@ -47,22 +47,19 @@ #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control /** - * Thermal Protection parameters + * Thermal Protection protects your printer from damage and fire if a + * thermistor falls out or temperature sensors fail in any way. + * + * The issue: If a thermistor falls out or a temperature sensor fails, + * Marlin can no longer sense the actual temperature. Since a disconnected + * thermistor reads as a low temperature, the firmware will keep the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too long (period), + * the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD */ - /** - * Thermal Protection protects your printer from damage and fire if a - * thermistor falls out or temperature sensors fail in any way. - * - * The issue: If a thermistor falls out or a temperature sensor fails, - * Marlin can no longer sense the actual temperature. Since a disconnected - * thermistor reads as a low temperature, the firmware will keep the heater on. - * - * The solution: Once the temperature reaches the target, start observing. - * If the temperature stays too far below the target (hysteresis) for too long (period), - * the firmware will halt the machine as a safety precaution. - * - * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD - */ #if ENABLED(THERMAL_PROTECTION_HOTENDS) #define THERMAL_PROTECTION_PERIOD 40 // Seconds #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius @@ -80,11 +77,11 @@ #define WATCH_TEMP_INCREASE 4 // Degrees Celsius #endif - /** - * Thermal Protection parameters for the bed - * are like the above for the hotends. - * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. - */ +/** + * Thermal Protection parameters for the bed + * are like the above for the hotends. + * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. + */ #if ENABLED(THERMAL_PROTECTION_BED) #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius diff --git a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h index c3ac27d7d..b5480ffa0 100644 --- a/Marlin/example_configurations/Hephestos_2/Configuration_adv.h +++ b/Marlin/example_configurations/Hephestos_2/Configuration_adv.h @@ -47,22 +47,19 @@ #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control /** - * Thermal Protection parameters + * Thermal Protection protects your printer from damage and fire if a + * thermistor falls out or temperature sensors fail in any way. + * + * The issue: If a thermistor falls out or a temperature sensor fails, + * Marlin can no longer sense the actual temperature. Since a disconnected + * thermistor reads as a low temperature, the firmware will keep the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too long (period), + * the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD */ - /** - * Thermal Protection protects your printer from damage and fire if a - * thermistor falls out or temperature sensors fail in any way. - * - * The issue: If a thermistor falls out or a temperature sensor fails, - * Marlin can no longer sense the actual temperature. Since a disconnected - * thermistor reads as a low temperature, the firmware will keep the heater on. - * - * The solution: Once the temperature reaches the target, start observing. - * If the temperature stays too far below the target (hysteresis) for too long (period), - * the firmware will halt the machine as a safety precaution. - * - * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD - */ #if ENABLED(THERMAL_PROTECTION_HOTENDS) #define THERMAL_PROTECTION_PERIOD 40 // Seconds #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius @@ -80,11 +77,11 @@ #define WATCH_TEMP_INCREASE 4 // Degrees Celsius #endif - /** - * Thermal Protection parameters for the bed - * are like the above for the hotends. - * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. - */ +/** + * Thermal Protection parameters for the bed + * are like the above for the hotends. + * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. + */ #if ENABLED(THERMAL_PROTECTION_BED) #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius diff --git a/Marlin/example_configurations/K8200/Configuration_adv.h b/Marlin/example_configurations/K8200/Configuration_adv.h index 3a58710a5..6a14bf913 100644 --- a/Marlin/example_configurations/K8200/Configuration_adv.h +++ b/Marlin/example_configurations/K8200/Configuration_adv.h @@ -53,22 +53,19 @@ #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control /** - * Thermal Protection parameters + * Thermal Protection protects your printer from damage and fire if a + * thermistor falls out or temperature sensors fail in any way. + * + * The issue: If a thermistor falls out or a temperature sensor fails, + * Marlin can no longer sense the actual temperature. Since a disconnected + * thermistor reads as a low temperature, the firmware will keep the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too long (period), + * the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD */ - /** - * Thermal Protection protects your printer from damage and fire if a - * thermistor falls out or temperature sensors fail in any way. - * - * The issue: If a thermistor falls out or a temperature sensor fails, - * Marlin can no longer sense the actual temperature. Since a disconnected - * thermistor reads as a low temperature, the firmware will keep the heater on. - * - * The solution: Once the temperature reaches the target, start observing. - * If the temperature stays too far below the target (hysteresis) for too long (period), - * the firmware will halt the machine as a safety precaution. - * - * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD - */ #if ENABLED(THERMAL_PROTECTION_HOTENDS) #define THERMAL_PROTECTION_PERIOD 60 // Seconds #define THERMAL_PROTECTION_HYSTERESIS 8 // Degrees Celsius @@ -86,11 +83,11 @@ #define WATCH_TEMP_INCREASE 4 // Degrees Celsius #endif - /** - * Thermal Protection parameters for the bed - * are like the above for the hotends. - * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. - */ +/** + * Thermal Protection parameters for the bed + * are like the above for the hotends. + * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. + */ #if ENABLED(THERMAL_PROTECTION_BED) #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius diff --git a/Marlin/example_configurations/RigidBot/Configuration_adv.h b/Marlin/example_configurations/RigidBot/Configuration_adv.h index 23233e510..79f71c720 100644 --- a/Marlin/example_configurations/RigidBot/Configuration_adv.h +++ b/Marlin/example_configurations/RigidBot/Configuration_adv.h @@ -47,22 +47,19 @@ #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control /** - * Thermal Protection parameters + * Thermal Protection protects your printer from damage and fire if a + * thermistor falls out or temperature sensors fail in any way. + * + * The issue: If a thermistor falls out or a temperature sensor fails, + * Marlin can no longer sense the actual temperature. Since a disconnected + * thermistor reads as a low temperature, the firmware will keep the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too long (period), + * the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD */ - /** - * Thermal Protection protects your printer from damage and fire if a - * thermistor falls out or temperature sensors fail in any way. - * - * The issue: If a thermistor falls out or a temperature sensor fails, - * Marlin can no longer sense the actual temperature. Since a disconnected - * thermistor reads as a low temperature, the firmware will keep the heater on. - * - * The solution: Once the temperature reaches the target, start observing. - * If the temperature stays too far below the target (hysteresis) for too long (period), - * the firmware will halt the machine as a safety precaution. - * - * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD - */ #if ENABLED(THERMAL_PROTECTION_HOTENDS) #define THERMAL_PROTECTION_PERIOD 40 // Seconds #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius @@ -80,11 +77,11 @@ #define WATCH_TEMP_INCREASE 4 // Degrees Celsius #endif - /** - * Thermal Protection parameters for the bed - * are like the above for the hotends. - * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. - */ +/** + * Thermal Protection parameters for the bed + * are like the above for the hotends. + * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. + */ #if ENABLED(THERMAL_PROTECTION_BED) #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius diff --git a/Marlin/example_configurations/SCARA/Configuration_adv.h b/Marlin/example_configurations/SCARA/Configuration_adv.h index a8ee979d2..ab8219fc2 100644 --- a/Marlin/example_configurations/SCARA/Configuration_adv.h +++ b/Marlin/example_configurations/SCARA/Configuration_adv.h @@ -47,22 +47,19 @@ #define BED_CHECK_INTERVAL 3000 //ms between checks in bang-bang control /** - * Thermal Protection parameters + * Thermal Protection protects your printer from damage and fire if a + * thermistor falls out or temperature sensors fail in any way. + * + * The issue: If a thermistor falls out or a temperature sensor fails, + * Marlin can no longer sense the actual temperature. Since a disconnected + * thermistor reads as a low temperature, the firmware will keep the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too long (period), + * the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD */ - /** - * Thermal Protection protects your printer from damage and fire if a - * thermistor falls out or temperature sensors fail in any way. - * - * The issue: If a thermistor falls out or a temperature sensor fails, - * Marlin can no longer sense the actual temperature. Since a disconnected - * thermistor reads as a low temperature, the firmware will keep the heater on. - * - * The solution: Once the temperature reaches the target, start observing. - * If the temperature stays too far below the target (hysteresis) for too long (period), - * the firmware will halt the machine as a safety precaution. - * - * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD - */ #if ENABLED(THERMAL_PROTECTION_HOTENDS) #define THERMAL_PROTECTION_PERIOD 40 // Seconds #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius @@ -80,11 +77,11 @@ #define WATCH_TEMP_INCREASE 4 // Degrees Celsius #endif - /** - * Thermal Protection parameters for the bed - * are like the above for the hotends. - * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. - */ +/** + * Thermal Protection parameters for the bed + * are like the above for the hotends. + * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. + */ #if ENABLED(THERMAL_PROTECTION_BED) #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius diff --git a/Marlin/example_configurations/TAZ4/Configuration_adv.h b/Marlin/example_configurations/TAZ4/Configuration_adv.h index 70d7db610..724b03cda 100644 --- a/Marlin/example_configurations/TAZ4/Configuration_adv.h +++ b/Marlin/example_configurations/TAZ4/Configuration_adv.h @@ -47,22 +47,19 @@ #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control /** - * Thermal Protection parameters + * Thermal Protection protects your printer from damage and fire if a + * thermistor falls out or temperature sensors fail in any way. + * + * The issue: If a thermistor falls out or a temperature sensor fails, + * Marlin can no longer sense the actual temperature. Since a disconnected + * thermistor reads as a low temperature, the firmware will keep the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too long (period), + * the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD */ - /** - * Thermal Protection protects your printer from damage and fire if a - * thermistor falls out or temperature sensors fail in any way. - * - * The issue: If a thermistor falls out or a temperature sensor fails, - * Marlin can no longer sense the actual temperature. Since a disconnected - * thermistor reads as a low temperature, the firmware will keep the heater on. - * - * The solution: Once the temperature reaches the target, start observing. - * If the temperature stays too far below the target (hysteresis) for too long (period), - * the firmware will halt the machine as a safety precaution. - * - * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD - */ #if ENABLED(THERMAL_PROTECTION_HOTENDS) #define THERMAL_PROTECTION_PERIOD 40 // Seconds #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius @@ -80,11 +77,11 @@ #define WATCH_TEMP_INCREASE 4 // Degrees Celsius #endif - /** - * Thermal Protection parameters for the bed - * are like the above for the hotends. - * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. - */ +/** + * Thermal Protection parameters for the bed + * are like the above for the hotends. + * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. + */ #if ENABLED(THERMAL_PROTECTION_BED) #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius diff --git a/Marlin/example_configurations/WITBOX/Configuration_adv.h b/Marlin/example_configurations/WITBOX/Configuration_adv.h index 2bd84d0b4..603a39a48 100644 --- a/Marlin/example_configurations/WITBOX/Configuration_adv.h +++ b/Marlin/example_configurations/WITBOX/Configuration_adv.h @@ -47,22 +47,19 @@ #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control /** - * Thermal Protection parameters + * Thermal Protection protects your printer from damage and fire if a + * thermistor falls out or temperature sensors fail in any way. + * + * The issue: If a thermistor falls out or a temperature sensor fails, + * Marlin can no longer sense the actual temperature. Since a disconnected + * thermistor reads as a low temperature, the firmware will keep the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too long (period), + * the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD */ - /** - * Thermal Protection protects your printer from damage and fire if a - * thermistor falls out or temperature sensors fail in any way. - * - * The issue: If a thermistor falls out or a temperature sensor fails, - * Marlin can no longer sense the actual temperature. Since a disconnected - * thermistor reads as a low temperature, the firmware will keep the heater on. - * - * The solution: Once the temperature reaches the target, start observing. - * If the temperature stays too far below the target (hysteresis) for too long (period), - * the firmware will halt the machine as a safety precaution. - * - * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD - */ #if ENABLED(THERMAL_PROTECTION_HOTENDS) #define THERMAL_PROTECTION_PERIOD 40 // Seconds #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius @@ -80,11 +77,11 @@ #define WATCH_TEMP_INCREASE 4 // Degrees Celsius #endif - /** - * Thermal Protection parameters for the bed - * are like the above for the hotends. - * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. - */ +/** + * Thermal Protection parameters for the bed + * are like the above for the hotends. + * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. + */ #if ENABLED(THERMAL_PROTECTION_BED) #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius diff --git a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h index ea7d782e2..371b7499b 100644 --- a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h +++ b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h @@ -47,22 +47,19 @@ #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control /** - * Thermal Protection parameters + * Thermal Protection protects your printer from damage and fire if a + * thermistor falls out or temperature sensors fail in any way. + * + * The issue: If a thermistor falls out or a temperature sensor fails, + * Marlin can no longer sense the actual temperature. Since a disconnected + * thermistor reads as a low temperature, the firmware will keep the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too long (period), + * the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD */ - /** - * Thermal Protection protects your printer from damage and fire if a - * thermistor falls out or temperature sensors fail in any way. - * - * The issue: If a thermistor falls out or a temperature sensor fails, - * Marlin can no longer sense the actual temperature. Since a disconnected - * thermistor reads as a low temperature, the firmware will keep the heater on. - * - * The solution: Once the temperature reaches the target, start observing. - * If the temperature stays too far below the target (hysteresis) for too long (period), - * the firmware will halt the machine as a safety precaution. - * - * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD - */ #if ENABLED(THERMAL_PROTECTION_HOTENDS) #define THERMAL_PROTECTION_PERIOD 40 // Seconds #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius @@ -80,11 +77,11 @@ #define WATCH_TEMP_INCREASE 4 // Degrees Celsius #endif - /** - * Thermal Protection parameters for the bed - * are like the above for the hotends. - * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. - */ +/** + * Thermal Protection parameters for the bed + * are like the above for the hotends. + * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. + */ #if ENABLED(THERMAL_PROTECTION_BED) #define THERMAL_PROTECTION_BED_PERIOD 120 // Seconds #define THERMAL_PROTECTION_BED_HYSTERESIS 4 // Degrees Celsius diff --git a/Marlin/example_configurations/delta/generic/Configuration_adv.h b/Marlin/example_configurations/delta/generic/Configuration_adv.h index c50f7e8bd..05c62c75c 100644 --- a/Marlin/example_configurations/delta/generic/Configuration_adv.h +++ b/Marlin/example_configurations/delta/generic/Configuration_adv.h @@ -47,22 +47,19 @@ #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control /** - * Thermal Protection parameters + * Thermal Protection protects your printer from damage and fire if a + * thermistor falls out or temperature sensors fail in any way. + * + * The issue: If a thermistor falls out or a temperature sensor fails, + * Marlin can no longer sense the actual temperature. Since a disconnected + * thermistor reads as a low temperature, the firmware will keep the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too long (period), + * the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD */ - /** - * Thermal Protection protects your printer from damage and fire if a - * thermistor falls out or temperature sensors fail in any way. - * - * The issue: If a thermistor falls out or a temperature sensor fails, - * Marlin can no longer sense the actual temperature. Since a disconnected - * thermistor reads as a low temperature, the firmware will keep the heater on. - * - * The solution: Once the temperature reaches the target, start observing. - * If the temperature stays too far below the target (hysteresis) for too long (period), - * the firmware will halt the machine as a safety precaution. - * - * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD - */ #if ENABLED(THERMAL_PROTECTION_HOTENDS) #define THERMAL_PROTECTION_PERIOD 40 // Seconds #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius @@ -80,11 +77,11 @@ #define WATCH_TEMP_INCREASE 4 // Degrees Celsius #endif - /** - * Thermal Protection parameters for the bed - * are like the above for the hotends. - * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. - */ +/** + * Thermal Protection parameters for the bed + * are like the above for the hotends. + * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. + */ #if ENABLED(THERMAL_PROTECTION_BED) #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h index 436d8c228..776efae90 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h @@ -47,22 +47,19 @@ #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control /** - * Thermal Protection parameters + * Thermal Protection protects your printer from damage and fire if a + * thermistor falls out or temperature sensors fail in any way. + * + * The issue: If a thermistor falls out or a temperature sensor fails, + * Marlin can no longer sense the actual temperature. Since a disconnected + * thermistor reads as a low temperature, the firmware will keep the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too long (period), + * the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD */ - /** - * Thermal Protection protects your printer from damage and fire if a - * thermistor falls out or temperature sensors fail in any way. - * - * The issue: If a thermistor falls out or a temperature sensor fails, - * Marlin can no longer sense the actual temperature. Since a disconnected - * thermistor reads as a low temperature, the firmware will keep the heater on. - * - * The solution: Once the temperature reaches the target, start observing. - * If the temperature stays too far below the target (hysteresis) for too long (period), - * the firmware will halt the machine as a safety precaution. - * - * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD - */ #if ENABLED(THERMAL_PROTECTION_HOTENDS) #define THERMAL_PROTECTION_PERIOD 40 // Seconds #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius @@ -80,11 +77,11 @@ #define WATCH_TEMP_INCREASE 4 // Degrees Celsius #endif - /** - * Thermal Protection parameters for the bed - * are like the above for the hotends. - * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. - */ +/** + * Thermal Protection parameters for the bed + * are like the above for the hotends. + * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. + */ #if ENABLED(THERMAL_PROTECTION_BED) #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius diff --git a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h index f7cb980b4..ff226d076 100644 --- a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h @@ -52,22 +52,19 @@ #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control /** - * Thermal Protection parameters + * Thermal Protection protects your printer from damage and fire if a + * thermistor falls out or temperature sensors fail in any way. + * + * The issue: If a thermistor falls out or a temperature sensor fails, + * Marlin can no longer sense the actual temperature. Since a disconnected + * thermistor reads as a low temperature, the firmware will keep the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too long (period), + * the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD */ - /** - * Thermal Protection protects your printer from damage and fire if a - * thermistor falls out or temperature sensors fail in any way. - * - * The issue: If a thermistor falls out or a temperature sensor fails, - * Marlin can no longer sense the actual temperature. Since a disconnected - * thermistor reads as a low temperature, the firmware will keep the heater on. - * - * The solution: Once the temperature reaches the target, start observing. - * If the temperature stays too far below the target (hysteresis) for too long (period), - * the firmware will halt the machine as a safety precaution. - * - * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD - */ #if ENABLED(THERMAL_PROTECTION_HOTENDS) #define THERMAL_PROTECTION_PERIOD 40 // Seconds #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius @@ -85,11 +82,11 @@ #define WATCH_TEMP_INCREASE 4 // Degrees Celsius #endif - /** - * Thermal Protection parameters for the bed - * are like the above for the hotends. - * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. - */ +/** + * Thermal Protection parameters for the bed + * are like the above for the hotends. + * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. + */ #if ENABLED(THERMAL_PROTECTION_BED) #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius diff --git a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h index 8fd808419..3c6ce07c4 100644 --- a/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h @@ -47,22 +47,19 @@ #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control /** - * Thermal Protection parameters + * Thermal Protection protects your printer from damage and fire if a + * thermistor falls out or temperature sensors fail in any way. + * + * The issue: If a thermistor falls out or a temperature sensor fails, + * Marlin can no longer sense the actual temperature. Since a disconnected + * thermistor reads as a low temperature, the firmware will keep the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too long (period), + * the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD */ - /** - * Thermal Protection protects your printer from damage and fire if a - * thermistor falls out or temperature sensors fail in any way. - * - * The issue: If a thermistor falls out or a temperature sensor fails, - * Marlin can no longer sense the actual temperature. Since a disconnected - * thermistor reads as a low temperature, the firmware will keep the heater on. - * - * The solution: Once the temperature reaches the target, start observing. - * If the temperature stays too far below the target (hysteresis) for too long (period), - * the firmware will halt the machine as a safety precaution. - * - * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD - */ #if ENABLED(THERMAL_PROTECTION_HOTENDS) #define THERMAL_PROTECTION_PERIOD 40 // Seconds #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius @@ -80,11 +77,11 @@ #define WATCH_TEMP_INCREASE 4 // Degrees Celsius #endif - /** - * Thermal Protection parameters for the bed - * are like the above for the hotends. - * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. - */ +/** + * Thermal Protection parameters for the bed + * are like the above for the hotends. + * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. + */ #if ENABLED(THERMAL_PROTECTION_BED) #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds #define THERMAL_PROTECTION_BED_HYSTERESIS 4 // Degrees Celsius diff --git a/Marlin/example_configurations/makibox/Configuration_adv.h b/Marlin/example_configurations/makibox/Configuration_adv.h index 8ec4d870a..c2e5550a7 100644 --- a/Marlin/example_configurations/makibox/Configuration_adv.h +++ b/Marlin/example_configurations/makibox/Configuration_adv.h @@ -47,22 +47,19 @@ #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control /** - * Thermal Protection parameters + * Thermal Protection protects your printer from damage and fire if a + * thermistor falls out or temperature sensors fail in any way. + * + * The issue: If a thermistor falls out or a temperature sensor fails, + * Marlin can no longer sense the actual temperature. Since a disconnected + * thermistor reads as a low temperature, the firmware will keep the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too long (period), + * the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD */ - /** - * Thermal Protection protects your printer from damage and fire if a - * thermistor falls out or temperature sensors fail in any way. - * - * The issue: If a thermistor falls out or a temperature sensor fails, - * Marlin can no longer sense the actual temperature. Since a disconnected - * thermistor reads as a low temperature, the firmware will keep the heater on. - * - * The solution: Once the temperature reaches the target, start observing. - * If the temperature stays too far below the target (hysteresis) for too long (period), - * the firmware will halt the machine as a safety precaution. - * - * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD - */ #if ENABLED(THERMAL_PROTECTION_HOTENDS) #define THERMAL_PROTECTION_PERIOD 40 // Seconds #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius @@ -80,11 +77,11 @@ #define WATCH_TEMP_INCREASE 4 // Degrees Celsius #endif - /** - * Thermal Protection parameters for the bed - * are like the above for the hotends. - * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. - */ +/** + * Thermal Protection parameters for the bed + * are like the above for the hotends. + * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. + */ #if ENABLED(THERMAL_PROTECTION_BED) #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h index f8630f0ae..d513cdfa6 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h @@ -47,22 +47,19 @@ #define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control /** - * Thermal Protection parameters + * Thermal Protection protects your printer from damage and fire if a + * thermistor falls out or temperature sensors fail in any way. + * + * The issue: If a thermistor falls out or a temperature sensor fails, + * Marlin can no longer sense the actual temperature. Since a disconnected + * thermistor reads as a low temperature, the firmware will keep the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too long (period), + * the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD */ - /** - * Thermal Protection protects your printer from damage and fire if a - * thermistor falls out or temperature sensors fail in any way. - * - * The issue: If a thermistor falls out or a temperature sensor fails, - * Marlin can no longer sense the actual temperature. Since a disconnected - * thermistor reads as a low temperature, the firmware will keep the heater on. - * - * The solution: Once the temperature reaches the target, start observing. - * If the temperature stays too far below the target (hysteresis) for too long (period), - * the firmware will halt the machine as a safety precaution. - * - * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD - */ #if ENABLED(THERMAL_PROTECTION_HOTENDS) #define THERMAL_PROTECTION_PERIOD 40 // Seconds #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius @@ -80,11 +77,11 @@ #define WATCH_TEMP_INCREASE 4 // Degrees Celsius #endif - /** - * Thermal Protection parameters for the bed - * are like the above for the hotends. - * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. - */ +/** + * Thermal Protection parameters for the bed + * are like the above for the hotends. + * WATCH_TEMP_BED_PERIOD and WATCH_TEMP_BED_INCREASE are not imlemented now. + */ #if ENABLED(THERMAL_PROTECTION_BED) #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius