Increase BABYSTEP_MULTIPLICATOR to 100

Ideally, it should be calculated based on Z steps per unit so that each
babystep corresponds to around 0.025mm. Smaller than this is largely
insignificant for typical layer heights.

Marlin/Configuration_adv.h

@@ -601,10 +601,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/AlephObjects/TAZ4/Configuration_adv.h

@@ -601,10 +601,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/Anet/A6/Configuration_adv.h

@@ -602,9 +602,9 @@
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
   //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/Anet/A8/Configuration_adv.h

@@ -601,10 +601,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/BQ/Hephestos/Configuration_adv.h

@@ -601,10 +601,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/BQ/Hephestos_2/Configuration_adv.h

@@ -601,10 +601,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/BQ/WITBOX/Configuration_adv.h

@@ -601,10 +601,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/Cartesio/Configuration_adv.h

@@ -601,10 +601,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/Felix/Configuration_adv.h

@@ -601,10 +601,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/Infitary/i3-M508/Configuration_adv.h

@@ -601,10 +601,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/Malyan/M150/Configuration_adv.h

@@ -601,10 +601,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/RigidBot/Configuration_adv.h

@@ -601,10 +601,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/SCARA/Configuration_adv.h

@@ -601,10 +601,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/Sanguinololu/Configuration_adv.h

@@ -590,10 +590,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/TinyBoy2/Configuration_adv.h

@@ -601,10 +601,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/Velleman/K8200/Configuration_adv.h

@@ -614,10 +614,10 @@
  */
 #define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/Velleman/K8400/Configuration_adv.h

@@ -601,10 +601,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h

@@ -603,10 +603,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/delta/generic/Configuration_adv.h

@@ -603,10 +603,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h

@@ -603,10 +603,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h

@@ -608,10 +608,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h

@@ -603,10 +603,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/makibox/Configuration_adv.h

@@ -601,10 +601,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h

@@ -601,10 +601,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.

Marlin/example_configurations/wt150/Configuration_adv.h

@@ -601,10 +601,10 @@
  */
 //#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define BABYSTEP_XY            // Also enable X/Y Babystepping. Not supported on DELTA!
-  #define BABYSTEP_INVERT_Z false  // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
+  //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
+  #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
+  #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
+  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
   //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.