diff --git a/Marlin/pins_SANGUINOLOLU_11.h b/Marlin/pins_SANGUINOLOLU_11.h index e2e36bc2b..97f2b3c36 100644 --- a/Marlin/pins_SANGUINOLOLU_11.h +++ b/Marlin/pins_SANGUINOLOLU_11.h @@ -14,34 +14,23 @@ #define Y_DIR_PIN 23 #define Y_STOP_PIN 19 -#define Z_STEP_PIN 3 -#define Z_DIR_PIN 2 +#define Z_STEP_PIN 3 +#define Z_DIR_PIN 2 #define Z_STOP_PIN 20 #define E0_STEP_PIN 1 #define E0_DIR_PIN 0 #define LED_PIN -1 - #define FAN_PIN -1 -// #if FAN_PIN == 12 || FAN_PIN ==13 -// #define FAN_SOFT_PWM -// #endif - -#if MB(MELZI) - #define LED_PIN 27 /* On some broken versions of the Sanguino libraries the pin definitions are wrong, which then needs LED_PIN as pin 28. But you better upgrade your Sanguino libraries! See #368. */ - #define FAN_PIN 4 // Works for Panelolu2 too -#endif - -#if MB(STB_11) - #define FAN_PIN 4 - // Uncomment this if you have the first generation (V1.10) of STBs board - #define LCD_PIN_BL 17 // LCD backlight LED -#endif - -#if MB(AZTEEG_X1) - #define FAN_PIN 4 +#if MB(AZTEEG_X1) || MB(STB_11) || MB(MELZI) + #define FAN_PIN 4 // Works for Panelolu2 too + #if MB(MELZI) + #define LED_PIN 27 // On some broken versions of the Sanguino libraries the pin definitions are wrong, so LED_PIN needs to be 28. But you should upgrade your Sanguino libraries! See #368. + #elif MB(STB_11) + #define LCD_PIN_BL 17 // LCD backlight LED + #endif #endif #ifdef Z_PROBE_SLED @@ -49,13 +38,13 @@ #endif #ifdef NUM_SERVOS - #define SERVO0_PIN -1 + #define SERVO0_PIN -1 #if NUM_SERVOS > 1 - #define SERVO1_PIN -1 + #define SERVO1_PIN -1 #if NUM_SERVOS > 2 - #define SERVO2_PIN -1 + #define SERVO2_PIN -1 #if NUM_SERVOS > 3 - #define SERVO3_PIN -1 + #define SERVO3_PIN -1 #endif #endif #endif @@ -70,23 +59,23 @@ #ifdef SANGUINOLOLU_V_1_2 - #define HEATER_BED_PIN 12 // (bed) - #define X_ENABLE_PIN 14 - #define Y_ENABLE_PIN 14 - #define Z_ENABLE_PIN 26 - #define E0_ENABLE_PIN 14 + #define HEATER_BED_PIN 12 // (bed) + #define X_ENABLE_PIN 14 + #define Y_ENABLE_PIN 14 + #define Z_ENABLE_PIN 26 + #define E0_ENABLE_PIN 14 #ifdef LCD_I2C_PANELOLU2 - #define FAN_PIN 4 // Uses Transistor1 (PWM) on Panelolu2's Sanguino Adapter Board to drive the fan + #define FAN_PIN 4 // Uses Transistor1 (PWM) on Panelolu2's Sanguino Adapter Board to drive the fan #endif #else - #define HEATER_BED_PIN 14 // (bed) - #define X_ENABLE_PIN -1 - #define Y_ENABLE_PIN -1 - #define Z_ENABLE_PIN -1 - #define E0_ENABLE_PIN -1 + #define HEATER_BED_PIN 14 // (bed) + #define X_ENABLE_PIN -1 + #define Y_ENABLE_PIN -1 + #define Z_ENABLE_PIN -1 + #define E0_ENABLE_PIN -1 #endif @@ -97,77 +86,101 @@ #define SDPOWER -1 #define SDSS 31 -/* On some broken versions of the Sanguino libraries the pin definitions are wrong, which then needs SDSS as pin 24. But you better upgrade your Sanguino libraries! See #368. */ +/** + * On some broken versions of the Sanguino libraries the pin definitions are wrong, + * which then needs SDSS as pin 24. But you should upgrade your Sanguino libraries! See #368. + */ //#define SDSS 24 -#ifdef ULTRA_LCD - #ifdef NEWPANEL - //we have no buzzer installed - #define BEEPER -1 - //LCD Pins - #ifdef DOGLCD - #ifdef U8GLIB_ST7920 //SPI GLCD 12864 ST7920 ( like [www.digole.com] ) For Melzi V2.0 - #define LCD_PINS_RS 30 //CS chip select /SS chip slave select - #define LCD_PINS_ENABLE 29 //SID (MOSI) - #define LCD_PINS_D4 17 //SCK (CLK) clock - #define BEEPER 27 // Pin 27 is take by LED_Pin, but Melzi LED do nothing with Marlin and I take this pin for BEEPER.... See here > [github.com] , If you want use this pin with Gcode M42 instead BEEPER - #else - // Pins for DOGM SPI LCD Support - #define DOGLCD_A0 30 - #define DOGLCD_CS 29 - #define LCD_CONTRAST 1 - #endif - // Uncomment screen orientation - #define LCD_SCREEN_ROT_0 - // #define LCD_SCREEN_ROT_90 - // #define LCD_SCREEN_ROT_180 - // #define LCD_SCREEN_ROT_270 - #else // standard Hitachi LCD controller - #define LCD_PINS_RS 4 - #define LCD_PINS_ENABLE 17 - #define LCD_PINS_D4 30 - #define LCD_PINS_D5 29 - #define LCD_PINS_D6 28 - #define LCD_PINS_D7 27 - #endif - //The encoder and click button - #define BTN_EN1 11 - #define BTN_EN2 10 - #ifdef LCD_I2C_PANELOLU2 - #if MB(MELZI) - #define BTN_ENC 29 //the click switch - #define LCD_SDSS 30 //to use the SD card reader on the Panelolu2 rather than the melzi board - #else - #define BTN_ENC 30 //the click switch - #endif - #else - #define BTN_ENC 16 //the click switch - #define LCD_SDSS 28 //to use the SD card reader on the smart controller rather than the melzi board - #endif //Panelolu2 - //not connected to a pin - #define SDCARDDETECT -1 - - #endif //NEWPANEL -#endif //ULTRA_LCD - -#ifdef MAKRPANEL - #define BEEPER 29 +#if defined(ULTRA_LCD) && defined(NEWPANEL) + + // No buzzer installed + #define BEEPER -1 + + // LCD Pins + #ifdef DOGLCD + + #ifdef U8GLIB_ST7920 //SPI GLCD 12864 ST7920 ( like [www.digole.com] ) For Melzi V2.0 + + #if MB(MELZI) // Melzi board + #define LCD_PINS_RS 30 //CS chip select /SS chip slave select + #define LCD_PINS_ENABLE 29 //SID (MOSI) + #define LCD_PINS_D4 17 //SCK (CLK) clock + #define BEEPER 27 // Pin 27 is take by LED_Pin, but Melzi LED do nothing with Marlin and I take this pin for BEEPER.... See here > [github.com] , If you want use this pin with Gcode M42 instead BEEPER + #else // Sanguinololu 1.3 + #define LCD_PINS_RS 4 + #define LCD_PINS_ENABLE 17 + #define LCD_PINS_D4 30 + #define LCD_PINS_D5 29 + #define LCD_PINS_D6 28 + #define LCD_PINS_D7 27 + #endif + + #else // DOGM SPI LCD Support + + #define DOGLCD_A0 30 + #define DOGLCD_CS 29 + #define LCD_CONTRAST 1 + + #endif + + // Uncomment screen orientation + #define LCD_SCREEN_ROT_0 + // #define LCD_SCREEN_ROT_90 + // #define LCD_SCREEN_ROT_180 + // #define LCD_SCREEN_ROT_270 + + #else // !DOGLCD - Standard Hitachi LCD controller + + #define LCD_PINS_RS 4 + #define LCD_PINS_ENABLE 17 + #define LCD_PINS_D4 30 + #define LCD_PINS_D5 29 + #define LCD_PINS_D6 28 + #define LCD_PINS_D7 27 + + #endif // !DOGLCD + + //The encoder and click button + #define BTN_EN1 11 + #define BTN_EN2 10 + #ifdef LCD_I2C_PANELOLU2 + #if MB(MELZI) + #define BTN_ENC 29 + #define LCD_SDSS 30 // Panelolu2 SD card reader rather than the Melzi + #else + #define BTN_ENC 30 + #endif + #else + #define BTN_ENC 16 + #define LCD_SDSS 28 // Smart Controller SD card reader rather than the Melzi + #endif //Panelolu2 + + #define SDCARDDETECT -1 + +#elif defined(MAKRPANEL) + + #define BEEPER 29 // Pins for DOGM SPI LCD Support - #define DOGLCD_A0 30 - #define DOGLCD_CS 17 - #define LCD_PIN_BL 28 // backlight LED on PA3 + #define DOGLCD_A0 30 + #define DOGLCD_CS 17 + #define LCD_PIN_BL 28 // backlight LED on PA3 // GLCD features - #define LCD_CONTRAST 1 + #define LCD_CONTRAST 1 // Uncomment screen orientation #define LCD_SCREEN_ROT_0 // #define LCD_SCREEN_ROT_90 // #define LCD_SCREEN_ROT_180 // #define LCD_SCREEN_ROT_270 //The encoder and click button - #define BTN_EN1 11 - #define BTN_EN2 10 - #define BTN_ENC 16 //the click switch - //not connected to a pin - #define SDCARDDETECT -1 -#endif //Makrpanel + #define BTN_EN1 11 + #define BTN_EN2 10 + #define BTN_ENC 16 + + #define SDCARDDETECT -1 +#endif // MAKRPANEL + +// #if FAN_PIN == 12 || FAN_PIN ==13 +// #define FAN_SOFT_PWM +// #endif