Merge pull request #5762 from Bob-the-Kuhn/Z_DUAL_ENDSTOP-make-offset-a-configuration-item

Z_DUAL_ENDSTOPS -  make offset a configuration item
master
Bob-the-Kuhn 8 years ago committed by GitHub
commit f87012a063

@ -285,6 +285,7 @@
#if ENABLED(Z_DUAL_ENDSTOPS)
#define Z2_USE_ENDSTOP _XMAX_
#define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine/test this value
#endif
#endif // Z_DUAL_STEPPER_DRIVERS

@ -963,7 +963,11 @@ void Config_ResetDefault() {
COPY(delta_diagonal_rod_trim, drt);
COPY(delta_tower_angle_trim, dta);
#elif ENABLED(Z_DUAL_ENDSTOPS)
z_endstop_adj = 0;
#if defined(Z_DUAL_ENDSTOPS_ADJUSTMENT)
float z_endstop_adj = Z_DUAL_ENDSTOPS_ADJUSTMENT;
#else
float z_endstop_adj = 0;
#endif
#endif
#if ENABLED(ULTIPANEL)

@ -285,6 +285,7 @@
#if ENABLED(Z_DUAL_ENDSTOPS)
#define Z2_USE_ENDSTOP _XMAX_
#define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine this value
#endif
#endif // Z_DUAL_STEPPER_DRIVERS

@ -285,6 +285,7 @@
#if ENABLED(Z_DUAL_ENDSTOPS)
#define Z2_USE_ENDSTOP _XMAX_
#define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine this value
#endif
#endif // Z_DUAL_STEPPER_DRIVERS

@ -285,6 +285,7 @@
#if ENABLED(Z_DUAL_ENDSTOPS)
#define Z2_USE_ENDSTOP _XMAX_
#define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine this value
#endif
#endif // Z_DUAL_STEPPER_DRIVERS

@ -285,6 +285,7 @@
#if ENABLED(Z_DUAL_ENDSTOPS)
#define Z2_USE_ENDSTOP _XMAX_
#define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine this value
#endif
#endif // Z_DUAL_STEPPER_DRIVERS

@ -298,6 +298,7 @@
#if ENABLED(Z_DUAL_ENDSTOPS)
#define Z2_USE_ENDSTOP _XMAX_
#define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine this value
#endif
#endif // Z_DUAL_STEPPER_DRIVERS

@ -285,6 +285,7 @@
#if ENABLED(Z_DUAL_ENDSTOPS)
#define Z2_USE_ENDSTOP _XMAX_
#define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine this value
#endif
#endif // Z_DUAL_STEPPER_DRIVERS

@ -285,6 +285,7 @@
#if ENABLED(Z_DUAL_ENDSTOPS)
#define Z2_USE_ENDSTOP _XMAX_
#define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine this value
#endif
#endif // Z_DUAL_STEPPER_DRIVERS

@ -285,6 +285,7 @@
#if ENABLED(Z_DUAL_ENDSTOPS)
#define Z2_USE_ENDSTOP _XMAX_
#define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine this value
#endif
#endif // Z_DUAL_STEPPER_DRIVERS

@ -293,6 +293,7 @@
#if ENABLED(Z_DUAL_ENDSTOPS)
#define Z2_USE_ENDSTOP _XMAX_
#define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine this value
#endif
#endif // Z_DUAL_STEPPER_DRIVERS

@ -285,6 +285,7 @@
#if ENABLED(Z_DUAL_ENDSTOPS)
#define Z2_USE_ENDSTOP _XMAX_
#define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine this value
#endif
#endif // Z_DUAL_STEPPER_DRIVERS

@ -285,6 +285,7 @@
#if ENABLED(Z_DUAL_ENDSTOPS)
#define Z2_USE_ENDSTOP _XMAX_
#define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine this value
#endif
#endif // Z_DUAL_STEPPER_DRIVERS

@ -285,6 +285,7 @@
#if ENABLED(Z_DUAL_ENDSTOPS)
#define Z2_USE_ENDSTOP _XMAX_
#define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine this value
#endif
#endif // Z_DUAL_STEPPER_DRIVERS

@ -285,6 +285,7 @@
#if ENABLED(Z_DUAL_ENDSTOPS)
#define Z2_USE_ENDSTOP _XMAX_
#define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine this value
#endif
#endif // Z_DUAL_STEPPER_DRIVERS

@ -290,6 +290,7 @@
#if ENABLED(Z_DUAL_ENDSTOPS)
#define Z2_USE_ENDSTOP _XMAX_
#define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine this value
#endif
#endif // Z_DUAL_STEPPER_DRIVERS

@ -285,6 +285,7 @@
#if ENABLED(Z_DUAL_ENDSTOPS)
#define Z2_USE_ENDSTOP _XMAX_
#define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine this value
#endif
#endif // Z_DUAL_STEPPER_DRIVERS

@ -285,6 +285,7 @@
#if ENABLED(Z_DUAL_ENDSTOPS)
#define Z2_USE_ENDSTOP _XMAX_
#define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine this value
#endif
#endif // Z_DUAL_STEPPER_DRIVERS

@ -285,6 +285,7 @@
#if ENABLED(Z_DUAL_ENDSTOPS)
#define Z2_USE_ENDSTOP _XMAX_
#define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // use M666 command to determine this value
#endif
#endif // Z_DUAL_STEPPER_DRIVERS

Loading…
Cancel
Save