0b310ab6c5
Merge pull request #1153 from xinfab/negative_values_in_menu
...
Negative values in menu
10 years ago
91d740e128
Merge pull request #1141 from filipmu/Filament-Sensor
...
Display filament sensor data on a 20x4 LCD or Graphical LCD
10 years ago
d088b5f30f
Remove debug echo
10 years ago
1fad8e6a81
Proper long file name var
10 years ago
29e854c535
Disable SDCARD_SORT_ALPHA by default
...
For legacy boards it’s better if this option is disabled.
10 years ago
6599adc184
Polish up a little...
10 years ago
a12eec33e2
Completed SORT_USES_MORE_RAM implementation
...
For the MORE_RAM option we need to buffer both the short and long
names, even though long names are sometimes redundant. Worst case, all
the names are max length. We can save some RAM by not storing these. We
could save more RAM by only storing the visible part of the long name.
10 years ago
c9486ebb85
Improvements, more SORT_USES_MORE_RAM
...
With this option, always keeps the dir in RAM, doubling as a cache for
getfilename. A board with only 8K of SRAM is cutting it very close.
10 years ago
b6ffea612a
Expand on More RAM concept, address minor bugs
10 years ago
8196b36ad9
SD Card Alpha Sorting
...
First iteration of alphabetical sorting for SD cards, both
slow+efficient and fast+rammy. Option for folders to sort first, last,
or not at all.
10 years ago
cf749dbeda
Completed SORT_USES_MORE_RAM implementation
...
For the MORE_RAM option we need to buffer both the short and long
names, even though long names are sometimes redundant. Worst case, all
the names are max length. We can save some RAM by not storing these. We
could save more RAM by only storing the visible part of the long name.
10 years ago
ae081d0fe0
Improvements, more SORT_USES_MORE_RAM
...
With this option, always keeps the dir in RAM, doubling as a cache for
getfilename. A board with only 8K of SRAM is cutting it very close.
10 years ago
785143a013
Expand on More RAM concept, address minor bugs
10 years ago
0cbbba08bd
SD Card Alpha Sorting
...
First iteration of alphabetical sorting for SD cards, both
slow+efficient and fast+rammy. Option for folders to sort first, last,
or not at all.
10 years ago
edfcf3b527
Toshiba Stepper Driver support
...
Tosh stepper drivers need to be driven slower, so the stepper code
was interleaved to separate the pin HIGH from the pin LOW. This adds
enough instructions to make it work, without needing nops.
10 years ago
c429a4b3ec
Toshiba Stepper Driver support
...
Tosh stepper drivers need to be driven slower, so the stepper code
was interleaved to separate the pin HIGH from the pin LOW. This adds
enough instructions to make it work, without needing nops.
10 years ago
1977b4490f
Merge pull request #1159 from thinkyhead/lcd_wait_better
...
M0/M1 Message Fix
10 years ago
7562183efc
Skip over spaces first
10 years ago
5a8b3a84ae
Merge pull request #1155 from thinkyhead/lcd_wait_better
...
M0-M1 Enhancements
10 years ago
433ac29d31
Updated a bit of spanish language
10 years ago
12b51d6060
Ignore S and P if no value >0 is included.
10 years ago
d12b24758a
Clear LCD to welcome_msg if not printing
...
The welcome message is more appropriate than “resuming print” if
nothing is printing.
10 years ago
3f54c9ba33
Relocate click ignore code into info screen
10 years ago
92e21d3ee2
M0-M1 Enhancements
...
Allow M0 and M1 to include a message string. Ignore clicks on “Wait for
user” so that the Info Screen stays up.
10 years ago
0d35b1d0b8
Allow negative values in menus
10 years ago
0d97dec434
Adaption of LCD info screen
...
Here comes a compile-time operation to match the extruder symbols on the
info screen to the set number of extruders in configuration.h.
When only one extruder is selected, the "1" on the symbol will not be
displayed.
10 years ago
3b1ab84536
Display Filament Sensor data on graphic LCD
...
Added support to show the filament width on the status line of the
graphic LCD. The status will show for 5 sec and then switch over to
data. Status can be seen by clicking the button.
10 years ago
d84934d8c5
Display Filament Sensor data on 20x4 LCD
...
Changes to support displaying the real-time filament width and the
volume factor on a 20x4 LCD. The data is displayed on the 4th line.
First the status message is displayed for 5 seconds, and then the
filament data is displayed. The status message can be seen by
re-selecting the info screen in the menu.
10 years ago
5c8107bcdd
Commented out FILAMENT_SENSOR #define
...
Commented out the FILAMENT_SENSOR define so that it is not enabled by
default. Code does not work on all hardware variants.
10 years ago
377dfb182f
Updated example configurations for Delta printers
10 years ago
724197454c
Merge pull request #1104 from ch100/Marlin_v1
...
Fixed typo.
10 years ago
058e446531
Merge pull request #1037 from filipmu/Filament-Sensor
...
Support for a filament diameter sensor
10 years ago
110c5dcf23
Fixed typo.
...
Signed-off-by: Christian Inci <chris.pcguy.inci@gmail.com>
10 years ago
ca30aee903
Fix "add_homeing" to "add_homing" to match changes
10 years ago
0733825fb1
Merge pull request #1099 from Fourmi/Marlin_v1
...
Update line 627 ,wrong number on thermistortables
10 years ago
af3e4d7510
Update line 627 ,wrong number on thermistortables
...
Wrong number on line 627 > i change number "12" by the correct number "13"
Soory
10 years ago
aaaf8fe8dd
Merge pull request #1068 from darkjavi/Marlin_v1
...
Added profile for RAMPS with 2 extruders and 1 fan, no heated bed
10 years ago
b360306881
Merge pull request #1073 from WingTangWong/wing-fix-float-delta
...
Wing fix float delta
10 years ago
ce85515428
Merge pull request #1082 from Fourmi/Marlin_v1
...
Add thermistor table
10 years ago
764921bdbf
Merge pull request #1091 from Aldert/patch-1
...
Update motion_control.cpp
10 years ago
c40c7b589b
Merge pull request #1095 from thinkyhead/codeclean
...
Simple code cleanup. Rename "homeing" to homing.
10 years ago
0f2e0525df
Merge pull request #1096 from thinkyhead/set-home
...
Proposed feature: Set Home Offsets
10 years ago
5ae02a361b
Merge pull request #1097 from thinkyhead/round-up-xyz
...
Adjust the Z display to hide float rounding errors
10 years ago
fb34265d75
Make hotend optional when compiling with lcd support
...
Signed-off-by: Matthew Schick <matthew.schick@gmail.com>
10 years ago
6e343ef2f0
Adjust the Z display to hide float rounding errors
10 years ago
2f6c57eadc
Proposed feature: Set Home Offsets
...
Add an item to the LCD menu that applies the current axis position to
the “add_homeing” offset.
10 years ago
f989bd5435
Simple code cleanup. Rename "homeing" to homing.
10 years ago
d1e4237e1d
Update motion_control.cpp
...
G03 Full circle did not work (G02 is working correct)
10 years ago
a664763e6f
Update thermistortables.h
...
Add another thermistor table (13),it's a cartridge thermistor up to +300°C,use with Hotend "Simple ONE" & "All In ONE"
Thx
10 years ago
b5dc228a7a
Update configuration.h
...
Add another comment for thermistor 13 ,use with Hotend "Simple ONE & All In ONE"
10 years ago
Bo Herrmannsen