Alexey Shvetsov
a8670b66a7
Update ru translation
...
Signed-off-by: Alexey Shvetsov <alexxy@gentoo.org>
9 years ago
Wurstnase
9c09967803
Merge pull request #2149 from Wurstnase/enstop_bits
...
faster compare
9 years ago
wurstnase
0f3f7d6835
clean up double endstops
9 years ago
AnHardt
9d2a980bcf
Merge pull request #2170 from thinkyhead/beep_M600_elsewise
...
Slight size reduction by adding idle()
9 years ago
AnHardt
2728dc0606
Merge pull request #2194 from thinkyhead/reduce_strings
...
Redo "invalid extruder" to save 304 bytes
9 years ago
Scott Lahteine
be5236e839
Reduce setTargetedHotend by removing the switch
9 years ago
Scott Lahteine
06f401e7e5
Redo "invalid extruder" to save 264 bytes
...
- Use `setTargetedHotend` in `M200`, as with other commands that use
`T` for the extruder
- Synthesize the "invalid extruder" message, obviating several long
strings
9 years ago
Scott Lahteine
1a882bcc2e
Merge pull request #2193 from thinkyhead/ignore_unrecognized_commands
...
Ignore unknown commands if they start with G, M, or T
9 years ago
Scott Lahteine
a672872717
Merge pull request #2187 from AnHardt/MAX6675M105
...
Print active extruder with M105 for MAX6675
9 years ago
Scott Lahteine
9beed830eb
Drop commented code_is_good lines
9 years ago
Scott Lahteine
068d4a1eb2
Ignore unknown commands if they start with G, M, or T
9 years ago
Scott Lahteine
5824f613ff
Merge pull request #2185 from jothan/bed_integral
...
Separate the maximum integral power for the bed from PID_INTEGRAL_DRI…
9 years ago
Scott Lahteine
c5c9d12630
Merge pull request #2183 from AnHardt/displayinit
...
Initialize the display earlier
9 years ago
Scott Lahteine
ef4becc413
Merge pull request #2188 from AnHardt/FtoN
...
Replace MSG_F? with MSG_N?
9 years ago
Scott Lahteine
0564625757
Update M33 for new gcode parser
9 years ago
AnHardt
f18f689c01
Replace MSG_F? with MSG_N?
...
To avoid double definitions.
I prefer to read N for Number not for Nozzle.
9 years ago
AnHardt
af7e3f5076
Print active extruder with M105 for MAX6675
...
Was omitted when T0 is a MAX6675.
9 years ago
Jonathan Bastien-Filiatrault
d46d9d998e
Add maximum bed integral term in example configurations.
9 years ago
Jonathan Bastien-Filiatrault
e86f2342c0
Separate the maximum integral power for the bed from PID_INTEGRAL_DRIVE_MAX / PID_MAX.
...
My PID_INTEGRAL_DRIVE_MAX was at 96, which was insufficient for my bed
to reach its intended temperature. The head requires a low maximum power since
I run on 24 volts and it has a somewhat low thermal mass.
9 years ago
AnHardt
f0523b5816
Initialize the display earlier
...
to have it ready to display errors during (temperature)-setup.
9 years ago
Scott Lahteine
790c697c19
Fix DEGREES macro
9 years ago
Scott Lahteine
76b4678f99
Merge pull request #2171 from thinkyhead/gcode_110_is_good
...
M110 is a known command
9 years ago
Scott Lahteine
03d5709b09
M110 is a known command
...
- The command parser now displays “unknown command” in more cases.
Known commands must be added to the `switch` inside `process_commands`
to suppress the error.
9 years ago
Scott Lahteine
d76a01194d
Slight size reduction by adding idle()
9 years ago
AnHardt
da246f5cb1
Activate BED_MINTEMP error.
...
And call _temp_error() directly for ERR_MAXTEMP_BED to avoid the only one time use of bed_max_temp_error().
Includes #2156 .
9 years ago
AnHardt
959da98d8e
Call kill() only once when triggered by a temperature error
...
to avoid stack overflow when called from interrupt.
Some clean up for calls of disable_all_heaters().
'disable_all_heaters()' is called in kill() and again when 'killed' is already set inside _temp_error().
9 years ago
Scott Lahteine
68f6f149d0
Reduce code size with out_of_range_error function
...
- Affects code size when automatic bed leveling is enabled
9 years ago
wurstnase
94120740d8
faster compare
...
!(~(ab)&0x3) and ab == 0x3 are equal
9 years ago
Scott Lahteine
c9141e604a
Merge pull request #2145 from thinkyhead/gcode_folding
...
Indentation in process_commands
9 years ago
Scott Lahteine
b55f8718c3
Indent G90/G91, G92
9 years ago
Scott Lahteine
b0d520b109
Indent G30, G31/G32
9 years ago
Scott Lahteine
ffe27a6225
Indent G29
9 years ago
Scott Lahteine
86083badc2
Indent G4, G10/G11, G28
9 years ago
Scott Lahteine
47d7a9cb5e
Indent G2/G3
9 years ago
Scott Lahteine
350f239d84
Indent G0/G1
9 years ago
Scott Lahteine
672b0c1fd3
Cleanup pins in RAMPS_13_EFB boards
9 years ago
Scott Lahteine
15a2351675
No need for +1 on initial seen_pointer
9 years ago
Scott Lahteine
550dd87b2a
Set seen_pointer before calling code_value
9 years ago
Scott Lahteine
38cc0b93c6
Merge pull request #1874 from AnHardt/Bulgarian
...
Introduction of Bulgarian - language_bg.h
9 years ago
Scott Lahteine
04a1622172
Merge pull request #2127 from Wackerbarth/Kossel_Pro
...
Kossel Pro
9 years ago
Scott Lahteine
81c2ca3e10
Merge pull request #2131 from thinkyhead/bq_is_ramps_13_efb
...
Witbox and Hephestos are RAMPS EFB
9 years ago
Scott Lahteine
f919a2fed1
Merge pull request #2134 from AnHardt/preheat-all
...
Shift call of start_watching_heater() into setTargetHotend()
9 years ago
Scott Lahteine
063881b5bd
Fix a couple of doubled semicolons
9 years ago
AnHardt
94dff5b36a
Merge pull request #2137 from thinkyhead/tweak_swh
...
Move millis call in start_watching_heater
9 years ago
Scott Lahteine
70d2f48d4e
Merge pull request #2136 from thinkyhead/M303_suppress_error
...
Suppress the line mismatch error after M303
9 years ago
AnHardt
0c0ace2a04
Remove start_watching_heater() fom M104 and M109
9 years ago
Scott Lahteine
00716d0ca0
Small start_watching_heater adjustment
9 years ago
Scott Lahteine
834747deb7
Merge pull request #2135 from Wurstnase/new_endstop_bits
...
new endstop bits
9 years ago
Scott Lahteine
bde9c70d42
Suppress the line mismatch error after M303
9 years ago
Scott Lahteine
50bd7493cc
Merge pull request #2108 from thinkyhead/m33_long_filename_host_support
...
M33 LONG_FILENAME_HOST_SUPPORT
9 years ago