ab6f1fdf8b
Move & document ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED (PR#2528)
...
As suggested in #2521
- Move `ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED` because `SDSUPPORT` is
also required.
- Add a note that endstops must be enabled for the feature to have any
effect
9 years ago
fd0e81b0c7
Distinguish between BUZZER and SPEAKER (PR#2513)
...
A speaker needs a AC or a pulsed DC to make a sound, a buzzer only needs a DC.
A buzzer has it's own resonator. It works in most cases to feed the buzzer with a pulsed DC, but the sound will not be as loud as with pure DC.
There seem to be boards where the BEEPER-pin is not able to handle a PWM. Obviously intended for a buzzer.
To make these board able to handle a speaker
* replace the PWM based tone()-function again with a on-delay-off-delay loop.
Hopefully the last time I touch the beeper code.
9 years ago
8b876241bd
Some more servo code tweaks
...
Just set up the pin. Don't move to a random position.
Simplify servo::move()
* servo::move() does not need the pin parameter - The pin is set during servo_init() with attach().
* servo::move() does not need a return value.
SERVO_LEVELING is the wrong condition to deactivate the servos.
Remove some temporary (Servo *) variables.
SanityCheck for the servo indexes.
9 years ago
90f8ddfc1e
Apply MINIPANEL to other configs
9 years ago
d85861d296
Move macros, add ENABLED/DISABLED, add includes
10 years ago
129f986ccf
Add COREXZ option to configurations
10 years ago
de25a48dec
Remove PID examples from preconfigured configs
10 years ago
7456710a1f
Update configs formatting
10 years ago
391386dd94
Update configs for new servo deactivation
10 years ago
c3c605c658
Move note about LiquidTWI2 to Configuration.h (PR#2406)
10 years ago
d78ebbc0e9
Remove unused MSG_OK_B and MSG_OK_T
10 years ago
4ce9ddbb74
Check the temperature before filament change
10 years ago
c461975140
Rename and repair MELZI_1284 (PR#2301)
...
to MELZI_MAKR3D.
Fix for #2288
As the normal MELZI also can have a 1284.
10 years ago
dc40a5f6e0
Patch up more outdated config lines
10 years ago
a274769f4f
Clean up spacing and comments
...
Also clean up some trailing spaces in a few other sources
10 years ago
d3bce05d54
Fix up spacing for filament sensor values
10 years ago
b4b10a57fe
Fix configurator section directives and values lists
10 years ago
bba14dcbe6
Move Z Safe Homing point to the middle of the movement range
10 years ago
c85a486445
make the dual z-endstop optional (PR#2277)
...
it's disabled by default
10 years ago
d1f4471000
Merge pull request #2146 from Wackerbarth/Versioning
...
Versioning
10 years ago
06f401e7e5
Redo "invalid extruder" to save 264 bytes
...
- Use `setTargetedHotend` in `M200`, as with other commands that use
`T` for the extruder
- Synthesize the "invalid extruder" message, obviating several long
strings
10 years ago
b5743d6927
Use SOURCE_CODE_URL rather than FIRMWARE_URL
10 years ago
5ea139fd79
Revised Versioning mechanism
10 years ago
38cc0b93c6
Merge pull request #1874 from AnHardt/Bulgarian
...
Introduction of Bulgarian - language_bg.h
10 years ago
81c2ca3e10
Merge pull request #2131 from thinkyhead/bq_is_ramps_13_efb
...
Witbox and Hephestos are RAMPS EFB
10 years ago
50bd7493cc
Merge pull request #2108 from thinkyhead/m33_long_filename_host_support
...
M33 LONG_FILENAME_HOST_SUPPORT
10 years ago
6eb4f90ce7
Also synchronize configurator copies of configs
10 years ago
9b8c6ed254
Merge pull request #2120 from chris-bo/dogm_config
...
move dogm font selection to configuration_adv.h
10 years ago
06513565e9
Merge pull request #2105 from eboston/Development
...
Add ELB_FULL_GRAPHIC_CONTROLLER with ADAFRUIT_ST7565 display.
10 years ago
082ed3beed
Propagate Configuration.h changes
...
Updated all the example Configuration.h files for the new display type.
10 years ago
7bc5fd8193
Merge pull request #2123 from AnHardt/Duemilanove
...
Remove Duemilanove
10 years ago
4d4fa3607b
Remove Duemilanove
...
No way to fit Marlin into 32K.
10 years ago
e353d27430
Merge branch 'Development' of https://github.com/MarlinFirmware/Marlin into Bulgarian
10 years ago
258bcdefe0
move dogm font selection to configuration_adv.h
10 years ago
7750180c93
transpire -> expire
...
Minor wording correction.
10 years ago
0f2c9bacfd
M33 LONG_FILENAME_HOST_SUPPORT
10 years ago
76438195f0
NO_TIMEOUTS and ADVANCED_OK off by default
10 years ago
78beef2d73
Use Mendel default for INVERT_Y_DIR
10 years ago
d693e0f378
Use WATCH_TEMP_INCREASE + TEMP_HYSTERESIS + 1 as difference limit
10 years ago
747fd5801c
Merge pull request #2055 from thinkyhead/thermal_unified
...
Combine thermal runaway and watch-period
10 years ago
429c6ccad2
Neaten config formatting
10 years ago
8a0dc4d54a
Merge pull request #1922 from Wurstnase/serial_wait
...
Serial wait
10 years ago
526ad82d20
activate advanced_ok and no_timeout
10 years ago
2445ae3d3a
Combine thermal runaway and watch-period
...
- Make thermal protection for all hotends and/or bed into simple
switches
- Now enable `WATCH_TEMP_PERIOD` when `THERMAL_PROTECTION_HOTENDS` is
enabled
- Move detailed thermal parameters to `Configuration_adv.h`
- Add sanity checks to warn about old configurations
- Change `WATCH_TEMP_PERIOD` to seconds instead of milliseconds
10 years ago
79106638a8
Fix documentation of heating sanity check
10 years ago
6110494a56
Change default to 4°C in 16s
10 years ago
54deb9eea3
Enable WATCH_TEMP_PERIOD by default
10 years ago
deedb00c18
Document WATCH_TEMP_PERIOD
10 years ago
7f3252eea9
Merge pull request #1999 from paclema/Filrunout_configurable_script
...
Added configurable script for filrunout from configuration.h
10 years ago
181ccc884c
Edit thermal runaway description
10 years ago
Scott Lahteine