bbc2ee6da1
Don't re-init graphical LCD after boot screen
...
Followup to 13a3fb1acc
7 years ago
b96ceb4256
[1.1.x] tool change bad behaviours
...
This PR will address two issues reported in #8492 . Just one is left because I don't know if it is an issue or not
1) when no home is done ("no_move" is set) tool change should never move X & Y because... I don't know where I am...only Z should be adjusted to avoid bed collision if other nozzle is lower than current.
2) Since no move no bed level matrix should be applied
When SWITCHING_NOZZLE is enabled and system is homed there are two movements to go to destination, but first can move Z to older position and then crash on the bed
7 years ago
b6dbc4c5c1
Merge pull request #8426 from SteveGotthardt/bugfixes
...
[1.1.x]Update Anet A8 default values from my Anet A8 experience
7 years ago
12b018e619
Merge pull request #8487 from Bob-the-Kuhn/M43-compatibility-1.1.x
...
[1.1.x] M43 end pin correction/compatibility
7 years ago
9b80e1e04a
change to L for end pin for M43 Toggle command
7 years ago
bf6a1816b4
Display volumetric ratio in terms of E mm
7 years ago
4f05a66ee1
Fixes #8472
7 years ago
622d100c30
No retroactive changes with M851 Z
7 years ago
74997a5251
Fix comment in planner.h
7 years ago
50148f7185
Update the UBL Probable Area for Delta's
...
This is a non-intuitive change. @oldmcg says in this post https://github.com/MarlinFirmware/Marlin/issues/7572#issuecomment-340641207 that using DELTA_PRINTABLE_RADIUS is better than DELTA_PROBABLE_RADIUS for setting the probe limits. This is because the automatic probe code checks all locations for being reachable by the probe prior to doing the probe.
7 years ago
8f57a3e28a
Apply coding standards to Max7219 code
7 years ago
2511e869e2
Update Configuration.h
7 years ago
aa612124f2
Merge pull request #8452 from tcm0116/1.1.x-pio_deps
...
[1.1.x] Fix PlatformIO dependencies
7 years ago
eb3bdb7550
Fix FILAMENT_LCD_DISPLAY, disabled state, optimize
7 years ago
97c19de8b9
Fix PlatformIO dependencies
7 years ago
4e19c59ab3
Miscellaneous cleanup
7 years ago
9cf5b96971
Fix M503 output for M145
...
Fixes #7978
7 years ago
69a710fef1
Add OV() macro for thermistor tables
7 years ago
d2613ce077
Merge pull request #8432 from thinkyhead/bf1_fix_M32_subroutines
...
[1.1] Fix 'M32 P' subroutines
7 years ago
f2e222b9e8
Merge pull request #8419 from RowanMeara/rm-dithering-1.1.x
...
[1.1.x] Fix Software Fan PWM
7 years ago
a6ee4a0468
Apply SDCARD_SORT_ALPHA changes from 2.0.x
7 years ago
d3b8f30818
Fix M32 P subroutine handling
7 years ago
2390f6d3ab
Cleanup, apply standards to SD lib, cardreader
7 years ago
eacb6b6e8b
Fix parser value handling
7 years ago
7efffc1548
Update Anet A8 default values from my Anet A8 experience
7 years ago
10e366ebd7
Change dithering behavior to intended.
7 years ago
95590adf07
Make sure `leveled[]` is enabled for use
7 years ago
8d06cf7b84
Add M114_DETAIL to Configuration_adv.h
7 years ago
645b586041
Fix warnings for REPRAPWORLD_KEYPAD
7 years ago
069ec3f9a9
Move Filament Width Sensor to Configuration_adv.h
7 years ago
56035e9965
Move mesh test options under G26 option
7 years ago
d65c99f38b
Drop unused LARGE_FLASH option
7 years ago
90c7d28055
Extrudrboard support for Printrboard Rev.F
7 years ago
8b684637bc
Merge pull request #8397 from RowanMeara/rm-M428-1.1.x
...
[1.1.x] Fix M428
7 years ago
d2df00bfca
[1.1.x] Fix compilation warnings ( #8395 )
...
* Fix up Travis CI and compile warnings/errors
* No ULTRA_LCD with REPRAP_DISCOUNT_SMART_CONTROLLER
* No point in setting all the endstop plugs
7 years ago
25ec0fecfa
Apply native workspace fixes to G92, G53-59
7 years ago
227b96b28b
Fix M428
...
This fixes the old implementation of M428 which was broken, did not
match the website, and made no sense.
7 years ago
a2c013c8c7
Fix LCD pins for Printrboard v1
7 years ago
f27196214b
Fix Printrboard pins for parity with 2.0
7 years ago
aa616cd410
No leveling data in M114 without leveling
7 years ago
5926159890
Fix report_current_position
...
Thanks @RowanMeara!
7 years ago
c9f88297b8
Provide more clearance for BL-Touch probe
7 years ago
5cc87abb3a
Merge pull request #8381 from thinkyhead/bf1_native_followup
...
[1.1] Remove offsets from soft endstops, tool change
7 years ago
355dfed437
Coding standard patch of M290
7 years ago
802ae73b13
Turn off laser power pin when PWM goes to 0
7 years ago
549c814e8d
Remove offsets from soft endstops, tool change
7 years ago
564fbc8dec
M290 constrain patch
7 years ago
df44bcc5ae
Use do_blocking_move_to where possible
7 years ago
3293823642
Add pre-calculated planner.e_factor
7 years ago
24b302c001
Fix cold/lengthy extrusion handling
7 years ago
Scott Lahteine