67c9b1e332
Update M665 comment, fix M665 code_value code.
8 years ago
37399e3cb5
Fix prepare_move_to_destination_cartesian for UBL
8 years ago
e51b5774db
Merge pull request #6699 from mtowara/patch-1
...
Bugfix PRINTER_EVENT_LEDS
8 years ago
056350d9bf
Merge pull request #6656 from FHeilmann/fix_fwretract_pos_z_move
...
Fix FWRetract with positive z-moves during retracted state
8 years ago
0e582bcfb7
Fix #6691 - redundant line in M665
8 years ago
68ae7c8d7a
Bugfix PRINTER_EVENT_LEDS
...
Extra closing curly bracket terminates while loop early if PRINTER_EVENT_LEDS defined
8 years ago
0696dda470
Cleanups to UBL_DELTA
8 years ago
cbfca29522
M421 tweaks, just to use const
8 years ago
233f824dd6
Define GRID_MAX_POINTS
8 years ago
b17e2d3dcd
Apply const in Marlin_main.cpp
8 years ago
92fbea2906
Add some GCodes to the header of Marlin_main.cpp
8 years ago
94e90ca26c
Tweak M80/M81 descriptions
8 years ago
91841d75c9
UBL_DELTA ( #6695 )
...
UBL on Delta's.... Should be close! Should not affect any Cartesian printer.
8 years ago
ae676490c9
M421: Add 'adjust closest point' capability
...
- Split M421 into separate versions for bilinear and ubl
- Fix minor issue in G26
8 years ago
9a688d1456
Merge pull request #6682 from thinkyhead/bf_M80_s_arg
...
"M80 S" to report the state of the PSU pin
8 years ago
b63e82f309
M421 Mesh Point Offset and misc. UBL clean up ( #6685 )
...
* M421 Mesh Point Offset and misc. UBL clean up
Allow M421 to accept an offset as well as absolute value for a specified
mesh point.
And misc. UBL clean up to reduce redundent code.
* Better error checking for M421
* Fix M421 Y index bug
I just noticed.... We've had a Y index bug for who knows how long?
8 years ago
539e0c2f31
"M80 S" to report the state of the PSU pin
8 years ago
081bf1f879
Patch #else / #endif comments
8 years ago
8d961b51cc
Eliminate M100 compiler warnings?
8 years ago
fe96376a73
Fix FWRetract with positive z-moves during retracted state
8 years ago
911a87e006
Disable SCARA feedrate scaling by default
8 years ago
71396f77d3
Cleanups following recent commits
8 years ago
a6dafb058e
Small reduction in error code size
8 years ago
a1e04942a2
Cleanup to software PWM variables
8 years ago
6cb0fa4128
Cleanup previous implementation of new quiet probing
...
Saves a few lines of code.
8 years ago
56ca47ab9d
Patch configuration temp units
8 years ago
d35e2fda10
Merge pull request #6622 from bgort/silentprobing
...
Improve BLTOUCH_HEATERS_OFF functionality
8 years ago
d92fa40c62
misc. UBL fixes ( #6631 )
...
* Restore LSF functionality
Some of the typo's persisted... Hopefully this gets them all fixed.
* Restore user's expectations of how G28 should behave
* Allow Nozzle size control with ornery host programs
8 years ago
faa270071d
Improve BLTOUCH_HEATERS_OFF functionality
...
- rename to PROBING_HEATERS_OFF
- move heater pausing functionality into thermalManager
- add variables, pause(), ispaused(), other functions
- add fan pausing functionality -> PROBING_FANS_OFF
- add probing_pause() wrapper
- move pausing into do_homing_move() and do_probe_move() to minimize quiet time and so other probe types can benefit
- example configs
8 years ago
ce507deb9f
Support temperature units in M503
8 years ago
a59066bca9
Various improvements - mostly UBL-related ( #6607 )
...
UBL Clean up.
8 years ago
6876e79d42
Tweak command index increment
8 years ago
267f3a03d9
Fixed USE_CONTROLLER_FAN #define usage
8 years ago
ae7c602031
fix error in M105 output -- use SERIAL_PROTOCOL for ints instead of SERIAL_PROTOCOL_F ( #6584 )
...
also removed wayward 'address of' ampersand in setTargetHotend and setTargetBed parameters
8 years ago
15268770f5
Fix broken fwretract recovery extruder feedrate
...
When both lowering and recovery are performed using the same "prepare_move_to_destination()" the extruder recovery feedrate ends up being ignored and, instead, is only capped by either the maximum e-speed or the time it takes to perform the z-lowering.
Performing the two moves separately from each other ensures a correct recovery feedrate.
8 years ago
58210c3a19
Merge pull request #6568 from thinkyhead/rc_bilinear_extension
...
Add EXTRAPOLATE_BEYOND_GRID option to bilinear leveling
8 years ago
da08e11acd
Add EXTRAPOLATE_BEYOND_GRID option to bilinear leveling
8 years ago
1196e3ca59
SDCard print completion can use "M0"
8 years ago
6854f08d22
Shut down autotemp in disable_all_heaters
8 years ago
e1b85ff67b
Merge pull request #6559 from thinkyhead/rc_more_optimal
...
Compact smart_fill_mesh slightly
8 years ago
2658cc707a
Treat temperature as integer, when possible
8 years ago
1b2c7ec20a
Make G26 compatible with inches and thermal unit modes
8 years ago
241bdffe65
Dress up Bilinear Leveling code
8 years ago
67ecf06cc4
Patch issue in gcode_M900
...
Noted in #6550
8 years ago
628391304f
Merge pull request #6552 from thinkyhead/rc_more_ubl_cleanup
...
Further cleanup of UBL
8 years ago
902fe76db9
Merge pull request #6556 from thinkyhead/rc_use_controller_fan
...
Implement USE_CONTROLLER_FAN as a feature
8 years ago
7ba7474a73
Drop extra parens from address-of operator
8 years ago
fc857c5b78
Merge pull request #6549 from thinkyhead/rc_bltouch_refix
...
Fix BLTOUCH_HEATERS_OFF bug
8 years ago
2c13922c46
Implement USE_CONTROLLER_FAN as a feature
8 years ago
492bc536bf
Modify debug methods to take PSTR
8 years ago
Scott Lahteine