6e1bc03d3b
Additional wrapping for #3140
9 years ago
f9ded2a7c4
Wrap macros to prevent bad expansions
9 years ago
614febaaf3
Fix acceleration limits
...
See: https://github.com/Ultimaker/Marlin/pull/7
9 years ago
71718d888a
Fix typos in check_axes_activity
9 years ago
ff13070b59
Use _BV macros, patch up others
9 years ago
209f5f21e0
Use macros where possible
...
Apply `constrain`, `NOMORE`, `NOLESS` and `CRITICAL_SECTION` macros
wherever possible.
9 years ago
34b8b9f0f5
Merge pull request #2995 from thinkyhead/rcbugfix_corexy_corexz
...
Add CORE support to st_get_position_mm (and elsewhere)
9 years ago
772460a7b8
Various minor spelling corrections
...
Redo of #2939 rebased against RCBugFix
9 years ago
373e8a1ad4
Fixes for COREXY and COREXZ coordinates
9 years ago
7a670e3911
Improve planner & stepper PR #263
9 years ago
78a347a01a
change nx, ny, nz and ne from float to long
...
st_set_position takes long
```void st_set_position(const long& x, const long& y, const long& z, const long& e)```
9 years ago
6d691aceee
change dx, dy, dz and de from float to long
...
anything is long, we don't need float there
9 years ago
0fbfb22506
Renaming delta speeds (PR2824)
...
dx -> dsx
dy -> dsy
dz -> dsz
de -> dse
9 years ago
9bdab4f3a8
Clean up "else" and other spacing
9 years ago
0c7f7ebcfb
Styling adjustments (PR#2668 & PR#2670)
...
Keep "astyled" reformatting
9 years ago
7b4bdc0203
DUAL_X_CARRIAGE motor enabling
...
As noted by @darkjavi et.al. in #103 , the E1 motor was not being enabled in planner.cpp when using DUAL_X_CARRIAGE. This patch enables and disables E1 as it should.
9 years ago
f690b82343
Remove extra MAX_FREQ_TIME define (PR#148)
9 years ago
6292d9e815
Rename ENABLE_AUTO_BED_LEVELING
...
With the introduction of the #if ENABLED(…)
reads better than
9 years ago
29b456ae07
Suppress some compiler warnings
9 years ago
46453905d6
Apply remaining ENABLED/DISABLED conditionals
9 years ago
bf6eb93c61
Overridable Options - Part 10 (PR#2562)
...
Apply `ENABLED` / `DISABLED` macros to planner files.
9 years ago
a0ae9e30df
don't pass integer by reference, inefficient. (PR#2547)
9 years ago
a1154d4a20
Enable Y and sanity-check CoreXZ (PR#2509)
9 years ago
9f53e2f0c9
Implement COREXZ in stepper.cpp and planner.cpp
9 years ago
fa00e1d97f
Explode conditions common to corexy and cartesian
9 years ago
54ddc1d417
Simplify DRY RUN (PR#2358)
...
Elsewhere DRYRUN turns off the heating elements
and ignores constraints on them.
Here, whenever motion is entered into the planner,
if DRY RUN is set, we instantly act as if the E_AXIS
is in the desired final position.
9 years ago
788eb6e647
planner.cpp: remove tab
...
planner.cpp: single evil and hidden tab removed ♻️ 😏
10 years ago
e55e65d1e4
planner.cpp: Add FAN_MIN_PWM for slow fan stopping issue …
...
@CONSULitAS
planner.cpp: Add FAN_MIN_PWM for slow fan stopping issue (V2.1 with
macro and linear scaling)
@thinkyhead thanks for idea on linear scaling
10 years ago
e400fce271
Merge pull request #2221 from MagoKimbra/Dryrun
...
Insert Debug DRYRUN Repetier Host compatible
10 years ago
e7e964432b
consistency name for multiplier
...
replace extruder_multiply with extruder_multiplier
like feedrate_multiplier or volumetric_multiplier
10 years ago
76306f9073
Insert Debug DRYRUN Repetier Host compatible
10 years ago
d76a01194d
Slight size reduction by adding idle()
10 years ago
513077c317
Minor change to fan kick
10 years ago
35493e1af9
Tweak to planner.cpp position.debug
10 years ago
0fca084ea6
Make EEPROM reproducible in GCode
...
With these changes the output of `M503 S0` is all you need to restore
the EEPROM. Building on this it is straightforward to save and restore
the EEPROM state using the SD card or external GCode file.
- Added `M145` to set “heatup states” for the LCD menu
- Added `M420` to toggle Mesh Bed Leveling
- Added `M421` to set a single Mesh coordinate
- Extended `Config_PrintSettings` with added M codes
- Cleaned up some comments here and there
10 years ago
3f02da646c
Make sure axis_active is cleared for #1908
10 years ago
ccddc280be
Apply three more commits
10 years ago
8857b9e921
Use the extruder argument in plan_buffer_line
10 years ago
1269c445ab
Catch dangerous extrude before trying several
10 years ago
3162971cd6
current_position not static
10 years ago
1d291be2ba
Fix de after PREVENT_DANGEROUS_EXTRUDE
...
- Set `de` to 0 when `position[E] = target[E]`
- Address regression mention in #1846
10 years ago
c185912c19
Latest upstream commits, mostly
10 years ago
e0d4368cb5
Minor code cleanup, move NUM_AXIS out of config
10 years ago
b98ebd517e
disable / enable_all_steppers functions
10 years ago
0e8182bbf2
Additional pin tests, cleanup
10 years ago
50a732360a
Replace extrudemultiply by extruder_multiply[active_extruder]
...
Fix for #1460 .
Seems to work with only one extruder. Can't test this myself with more.
10 years ago
afff968e88
ARRAY_BY_EXTRUDERS, shorthand to sync planner
...
- Add some documentation to planner and stepper headers
- Patch up RAMBO pins with undefs
- Add `sync_plan_position` inline to set current XYZE
- Swap indices in `extruder_offset` to fix initialization values
10 years ago
19d418cd6a
Fix up the code to eliminate warnings
10 years ago
88e81a4804
Latest upstream commits, plus fixes
...
- Also add Manual Bed Leveling to the rest of the configs
10 years ago
af14c684b5
Minor optimizations to planner code
...
- Prefetch values used more than once
10 years ago
Scott Lahteine