You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
205 lines
8.4 KiB
205 lines
8.4 KiB
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
|
|
/**
|
|
* \file
|
|
* \brief Sd2Card class for V2 SD/SDHC cards
|
|
*/
|
|
|
|
/**
|
|
* Arduino Sd2Card Library
|
|
* Copyright (C) 2009 by William Greiman
|
|
*
|
|
* This file is part of the Arduino Sd2Card Library
|
|
*/
|
|
#ifndef _SD2CARD_H_
|
|
#define _SD2CARD_H_
|
|
|
|
#include "SdFatConfig.h"
|
|
#include "SdInfo.h"
|
|
|
|
// SPI speed is F_CPU/2^(1 + index), 0 <= index <= 6
|
|
uint8_t const SPI_FULL_SPEED = 0, // Set SCK to max rate of F_CPU/2. See Sd2Card::setSckRate().
|
|
SPI_HALF_SPEED = 1, // Set SCK rate to F_CPU/4. See Sd2Card::setSckRate().
|
|
SPI_QUARTER_SPEED = 2, // Set SCK rate to F_CPU/8. See Sd2Card::setSckRate().
|
|
SPI_EIGHTH_SPEED = 3, // Set SCK rate to F_CPU/16. See Sd2Card::setSckRate().
|
|
SPI_SIXTEENTH_SPEED = 4; // Set SCK rate to F_CPU/32. See Sd2Card::setSckRate().
|
|
|
|
uint16_t const SD_INIT_TIMEOUT = 2000, // init timeout ms
|
|
SD_ERASE_TIMEOUT = 10000, // erase timeout ms
|
|
SD_READ_TIMEOUT = 300, // read timeout ms
|
|
SD_WRITE_TIMEOUT = 600; // write time out ms
|
|
|
|
// SD card errors
|
|
uint8_t const SD_CARD_ERROR_CMD0 = 0X1, // timeout error for command CMD0 (initialize card in SPI mode)
|
|
SD_CARD_ERROR_CMD8 = 0X2, // CMD8 was not accepted - not a valid SD card
|
|
SD_CARD_ERROR_CMD12 = 0X3, // card returned an error response for CMD12 (write stop)
|
|
SD_CARD_ERROR_CMD17 = 0X4, // card returned an error response for CMD17 (read block)
|
|
SD_CARD_ERROR_CMD18 = 0X5, // card returned an error response for CMD18 (read multiple block)
|
|
SD_CARD_ERROR_CMD24 = 0X6, // card returned an error response for CMD24 (write block)
|
|
SD_CARD_ERROR_CMD25 = 0X7, // WRITE_MULTIPLE_BLOCKS command failed
|
|
SD_CARD_ERROR_CMD58 = 0X8, // card returned an error response for CMD58 (read OCR)
|
|
SD_CARD_ERROR_ACMD23 = 0X9, // SET_WR_BLK_ERASE_COUNT failed
|
|
SD_CARD_ERROR_ACMD41 = 0XA, // ACMD41 initialization process timeout
|
|
SD_CARD_ERROR_BAD_CSD = 0XB, // card returned a bad CSR version field
|
|
SD_CARD_ERROR_ERASE = 0XC, // erase block group command failed
|
|
SD_CARD_ERROR_ERASE_SINGLE_BLOCK = 0XD, // card not capable of single block erase
|
|
SD_CARD_ERROR_ERASE_TIMEOUT = 0XE, // Erase sequence timed out
|
|
SD_CARD_ERROR_READ = 0XF, // card returned an error token instead of read data
|
|
SD_CARD_ERROR_READ_REG = 0x10, // read CID or CSD failed
|
|
SD_CARD_ERROR_READ_TIMEOUT = 0x11, // timeout while waiting for start of read data
|
|
SD_CARD_ERROR_STOP_TRAN = 0x12, // card did not accept STOP_TRAN_TOKEN
|
|
SD_CARD_ERROR_WRITE = 0x13, // card returned an error token as a response to a write operation
|
|
SD_CARD_ERROR_WRITE_BLOCK_ZERO = 0x14, // REMOVE - not used ... attempt to write protected block zero
|
|
SD_CARD_ERROR_WRITE_MULTIPLE = 0x15, // card did not go ready for a multiple block write
|
|
SD_CARD_ERROR_WRITE_PROGRAMMING = 0x16, // card returned an error to a CMD13 status check after a write
|
|
SD_CARD_ERROR_WRITE_TIMEOUT = 0x17, // timeout occurred during write programming
|
|
SD_CARD_ERROR_SCK_RATE = 0x18, // incorrect rate selected
|
|
SD_CARD_ERROR_INIT_NOT_CALLED = 0x19, // init() not called
|
|
SD_CARD_ERROR_CRC = 0x20; // crc check error
|
|
|
|
// card types
|
|
uint8_t const SD_CARD_TYPE_SD1 = 1, // Standard capacity V1 SD card
|
|
SD_CARD_TYPE_SD2 = 2, // Standard capacity V2 SD card
|
|
SD_CARD_TYPE_SDHC = 3; // High Capacity SD card
|
|
|
|
/**
|
|
* define SOFTWARE_SPI to use bit-bang SPI
|
|
*/
|
|
#if MEGA_SOFT_SPI
|
|
#define SOFTWARE_SPI
|
|
#elif USE_SOFTWARE_SPI
|
|
#define SOFTWARE_SPI
|
|
#endif
|
|
|
|
// SPI pin definitions - do not edit here - change in SdFatConfig.h
|
|
#if DISABLED(SOFTWARE_SPI)
|
|
// hardware pin defs
|
|
#define SD_CHIP_SELECT_PIN SS_PIN // The default chip select pin for the SD card is SS.
|
|
// The following three pins must not be redefined for hardware SPI.
|
|
#define SPI_MOSI_PIN MOSI_PIN // SPI Master Out Slave In pin
|
|
#define SPI_MISO_PIN MISO_PIN // SPI Master In Slave Out pin
|
|
#define SPI_SCK_PIN SCK_PIN // SPI Clock pin
|
|
#else // SOFTWARE_SPI
|
|
#define SD_CHIP_SELECT_PIN SOFT_SPI_CS_PIN // SPI chip select pin
|
|
#define SPI_MOSI_PIN SOFT_SPI_MOSI_PIN // SPI Master Out Slave In pin
|
|
#define SPI_MISO_PIN SOFT_SPI_MISO_PIN // SPI Master In Slave Out pin
|
|
#define SPI_SCK_PIN SOFT_SPI_SCK_PIN // SPI Clock pin
|
|
#endif // SOFTWARE_SPI
|
|
|
|
/**
|
|
* \class Sd2Card
|
|
* \brief Raw access to SD and SDHC flash memory cards.
|
|
*/
|
|
class Sd2Card {
|
|
public:
|
|
|
|
Sd2Card() : errorCode_(SD_CARD_ERROR_INIT_NOT_CALLED), type_(0) {}
|
|
|
|
uint32_t cardSize();
|
|
bool erase(uint32_t firstBlock, uint32_t lastBlock);
|
|
bool eraseSingleBlockEnable();
|
|
|
|
/**
|
|
* Set SD error code.
|
|
* \param[in] code value for error code.
|
|
*/
|
|
void error(uint8_t code) {errorCode_ = code;}
|
|
|
|
/**
|
|
* \return error code for last error. See Sd2Card.h for a list of error codes.
|
|
*/
|
|
int errorCode() const {return errorCode_;}
|
|
|
|
/** \return error data for last error. */
|
|
int errorData() const {return status_;}
|
|
|
|
/**
|
|
* Initialize an SD flash memory card with default clock rate and chip
|
|
* select pin. See sd2Card::init(uint8_t sckRateID, uint8_t chipSelectPin).
|
|
*
|
|
* \return true for success or false for failure.
|
|
*/
|
|
bool init(uint8_t sckRateID = SPI_FULL_SPEED,
|
|
uint8_t chipSelectPin = SD_CHIP_SELECT_PIN);
|
|
bool readBlock(uint32_t block, uint8_t* dst);
|
|
|
|
/**
|
|
* Read a card's CID register. The CID contains card identification
|
|
* information such as Manufacturer ID, Product name, Product serial
|
|
* number and Manufacturing date.
|
|
*
|
|
* \param[out] cid pointer to area for returned data.
|
|
*
|
|
* \return true for success or false for failure.
|
|
*/
|
|
bool readCID(cid_t* cid) { return readRegister(CMD10, cid); }
|
|
|
|
/**
|
|
* Read a card's CSD register. The CSD contains Card-Specific Data that
|
|
* provides information regarding access to the card's contents.
|
|
*
|
|
* \param[out] csd pointer to area for returned data.
|
|
*
|
|
* \return true for success or false for failure.
|
|
*/
|
|
bool readCSD(csd_t* csd) { return readRegister(CMD9, csd); }
|
|
|
|
bool readData(uint8_t* dst);
|
|
bool readStart(uint32_t blockNumber);
|
|
bool readStop();
|
|
bool setSckRate(uint8_t sckRateID);
|
|
/**
|
|
* Return the card type: SD V1, SD V2 or SDHC
|
|
* \return 0 - SD V1, 1 - SD V2, or 3 - SDHC.
|
|
*/
|
|
int type() const {return type_;}
|
|
bool writeBlock(uint32_t blockNumber, const uint8_t* src);
|
|
bool writeData(const uint8_t* src);
|
|
bool writeStart(uint32_t blockNumber, uint32_t eraseCount);
|
|
bool writeStop();
|
|
|
|
private:
|
|
uint8_t chipSelectPin_,
|
|
errorCode_,
|
|
spiRate_,
|
|
status_,
|
|
type_;
|
|
|
|
// private functions
|
|
uint8_t cardAcmd(uint8_t cmd, uint32_t arg) {
|
|
cardCommand(CMD55, 0);
|
|
return cardCommand(cmd, arg);
|
|
}
|
|
uint8_t cardCommand(uint8_t cmd, uint32_t arg);
|
|
|
|
bool readData(uint8_t* dst, uint16_t count);
|
|
bool readRegister(uint8_t cmd, void* buf);
|
|
void chipSelectHigh();
|
|
void chipSelectLow();
|
|
void type(uint8_t value) { type_ = value; }
|
|
bool waitNotBusy(uint16_t timeoutMillis);
|
|
bool writeData(uint8_t token, const uint8_t* src);
|
|
};
|
|
|
|
#endif // _SD2CARD_H_
|