You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
107 lines
3.5 KiB
107 lines
3.5 KiB
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
|
|
#include "MarlinConfig.h"
|
|
|
|
#if ENABLED(DIGIPOT_I2C) && ENABLED(DIGIPOT_MCP4018)
|
|
|
|
#include "enum.h"
|
|
#include "Stream.h"
|
|
#include "utility/twi.h"
|
|
#include <SlowSoftI2CMaster.h> //https://github.com/stawel/SlowSoftI2CMaster
|
|
|
|
// Settings for the I2C based DIGIPOT (MCP4018) based on WT150
|
|
|
|
#define DIGIPOT_I2C_ADDRESS 0x2F
|
|
|
|
#define DIGIPOT_A4988_Rsx 0.250
|
|
#define DIGIPOT_A4988_Vrefmax 1.666
|
|
#define DIGIPOT_A4988_MAX_VALUE 127
|
|
|
|
#define DIGIPOT_A4988_Itripmax(Vref) ((Vref)/(8.0*DIGIPOT_A4988_Rsx))
|
|
|
|
#define DIGIPOT_A4988_FACTOR ((DIGIPOT_A4988_MAX_VALUE)/DIGIPOT_A4988_Itripmax(DIGIPOT_A4988_Vrefmax))
|
|
#define DIGIPOT_A4988_MAX_CURRENT 2.0
|
|
|
|
static byte current_to_wiper(const float current) {
|
|
const int16_t value = ceil(float(DIGIPOT_A4988_FACTOR) * current);
|
|
return byte(constrain(value, 0, DIGIPOT_A4988_MAX_VALUE));
|
|
}
|
|
|
|
const uint8_t sda_pins[DIGIPOT_I2C_NUM_CHANNELS] = {
|
|
DIGIPOTS_I2C_SDA_X
|
|
#if DIGIPOT_I2C_NUM_CHANNELS > 1
|
|
, DIGIPOTS_I2C_SDA_Y
|
|
#if DIGIPOT_I2C_NUM_CHANNELS > 2
|
|
, DIGIPOTS_I2C_SDA_Z
|
|
#if DIGIPOT_I2C_NUM_CHANNELS > 3
|
|
, DIGIPOTS_I2C_SDA_E0
|
|
#if DIGIPOT_I2C_NUM_CHANNELS > 4
|
|
, DIGIPOTS_I2C_SDA_E1
|
|
#endif
|
|
#endif
|
|
#endif
|
|
#endif
|
|
};
|
|
|
|
static SlowSoftI2CMaster pots[DIGIPOT_I2C_NUM_CHANNELS] = {
|
|
SlowSoftI2CMaster { sda_pins[X_AXIS], DIGIPOTS_I2C_SCL }
|
|
#if DIGIPOT_I2C_NUM_CHANNELS > 1
|
|
, SlowSoftI2CMaster { sda_pins[Y_AXIS], DIGIPOTS_I2C_SCL }
|
|
#if DIGIPOT_I2C_NUM_CHANNELS > 2
|
|
, SlowSoftI2CMaster { sda_pins[Z_AXIS], DIGIPOTS_I2C_SCL }
|
|
#if DIGIPOT_I2C_NUM_CHANNELS > 3
|
|
, SlowSoftI2CMaster { sda_pins[E_AXIS], DIGIPOTS_I2C_SCL }
|
|
#if DIGIPOT_I2C_NUM_CHANNELS > 4
|
|
, SlowSoftI2CMaster { sda_pins[E_AXIS + 1], DIGIPOTS_I2C_SCL }
|
|
#endif
|
|
#endif
|
|
#endif
|
|
#endif
|
|
};
|
|
|
|
static void i2c_send(const uint8_t channel, const byte v) {
|
|
if (WITHIN(channel, 0, DIGIPOT_I2C_NUM_CHANNELS - 1)) {
|
|
pots[channel].i2c_start(((DIGIPOT_I2C_ADDRESS) << 1) | I2C_WRITE);
|
|
pots[channel].i2c_write(v);
|
|
pots[channel].i2c_stop();
|
|
}
|
|
}
|
|
|
|
// This is for the MCP4018 I2C based digipot
|
|
void digipot_i2c_set_current(uint8_t channel, float current) {
|
|
i2c_send(channel, current_to_wiper(min(max(current, 0.0f), float(DIGIPOT_A4988_MAX_CURRENT))));
|
|
}
|
|
|
|
void digipot_i2c_init() {
|
|
static const float digipot_motor_current[] PROGMEM = DIGIPOT_I2C_MOTOR_CURRENTS;
|
|
|
|
for (uint8_t i = 0; i < DIGIPOT_I2C_NUM_CHANNELS; i++)
|
|
pots[i].i2c_init();
|
|
|
|
// setup initial currents as defined in Configuration_adv.h
|
|
for (uint8_t i = 0; i < COUNT(digipot_motor_current); i++)
|
|
digipot_i2c_set_current(i, pgm_read_float(&digipot_motor_current[i]));
|
|
}
|
|
|
|
#endif // DIGIPOT_I2C && DIGIPOT_MCP4018
|