You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

930 lines
30 KiB

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Conditionals_post.h
* Defines that depend on configuration but are not editable.
*/
#ifndef CONDITIONALS_POST_H
#define CONDITIONALS_POST_H
/**
* Axis lengths and center
*/
#define X_MAX_LENGTH (X_MAX_POS - (X_MIN_POS))
#define Y_MAX_LENGTH (Y_MAX_POS - (Y_MIN_POS))
#define Z_MAX_LENGTH (Z_MAX_POS - (Z_MIN_POS))
// Defined only if the sanity-check is bypassed
#ifndef X_BED_SIZE
#define X_BED_SIZE X_MAX_LENGTH
#endif
#ifndef Y_BED_SIZE
#define Y_BED_SIZE Y_MAX_LENGTH
#endif
#if ENABLED(BED_CENTER_AT_0_0)
#define X_CENTER 0
#define Y_CENTER 0
#else
#define X_CENTER ((X_BED_SIZE) / 2)
#define Y_CENTER ((Y_BED_SIZE) / 2)
#endif
#define Z_CENTER ((Z_MIN_POS + Z_MAX_POS) / 2)
#define X_MIN_BED (X_CENTER - (X_BED_SIZE) / 2)
#define X_MAX_BED (X_CENTER + (X_BED_SIZE) / 2)
#define Y_MIN_BED (Y_CENTER - (Y_BED_SIZE) / 2)
#define Y_MAX_BED (Y_CENTER + (Y_BED_SIZE) / 2)
/**
* CoreXY, CoreXZ, and CoreYZ - and their reverse
*/
#define CORE_IS_XY (ENABLED(COREXY) || ENABLED(COREYX))
#define CORE_IS_XZ (ENABLED(COREXZ) || ENABLED(COREZX))
#define CORE_IS_YZ (ENABLED(COREYZ) || ENABLED(COREZY))
#define IS_CORE (CORE_IS_XY || CORE_IS_XZ || CORE_IS_YZ)
#if IS_CORE
#if CORE_IS_XY
#define CORE_AXIS_1 A_AXIS
#define CORE_AXIS_2 B_AXIS
#define NORMAL_AXIS Z_AXIS
#elif CORE_IS_XZ
#define CORE_AXIS_1 A_AXIS
#define NORMAL_AXIS Y_AXIS
#define CORE_AXIS_2 C_AXIS
#elif CORE_IS_YZ
#define NORMAL_AXIS X_AXIS
#define CORE_AXIS_1 B_AXIS
#define CORE_AXIS_2 C_AXIS
#endif
#if (ENABLED(COREYX) || ENABLED(COREZX) || ENABLED(COREZY))
#define CORESIGN(n) (-(n))
#else
#define CORESIGN(n) (n)
#endif
#endif
#define IS_SCARA (ENABLED(MORGAN_SCARA) || ENABLED(MAKERARM_SCARA))
#define IS_KINEMATIC (ENABLED(DELTA) || IS_SCARA)
#define IS_CARTESIAN !IS_KINEMATIC
/**
* No adjustable bed on non-cartesians
*/
#if IS_KINEMATIC
#undef LEVEL_BED_CORNERS
#endif
/**
* SCARA cannot use SLOWDOWN and requires QUICKHOME
*/
#if IS_SCARA
#undef SLOWDOWN
#define QUICK_HOME
#endif
/**
* Set the home position based on settings or manual overrides
*/
#ifdef MANUAL_X_HOME_POS
#define X_HOME_POS MANUAL_X_HOME_POS
#elif ENABLED(BED_CENTER_AT_0_0)
#if ENABLED(DELTA)
#define X_HOME_POS 0
#else
#define X_HOME_POS ((X_BED_SIZE) * (X_HOME_DIR) * 0.5)
#endif
#else
#if ENABLED(DELTA)
#define X_HOME_POS (X_MIN_POS + (X_BED_SIZE) * 0.5)
#else
#define X_HOME_POS (X_HOME_DIR < 0 ? X_MIN_POS : X_MAX_POS)
#endif
#endif
#ifdef MANUAL_Y_HOME_POS
#define Y_HOME_POS MANUAL_Y_HOME_POS
#elif ENABLED(BED_CENTER_AT_0_0)
#if ENABLED(DELTA)
#define Y_HOME_POS 0
#else
#define Y_HOME_POS ((Y_BED_SIZE) * (Y_HOME_DIR) * 0.5)
#endif
#else
#if ENABLED(DELTA)
#define Y_HOME_POS (Y_MIN_POS + (Y_BED_SIZE) * 0.5)
#else
#define Y_HOME_POS (Y_HOME_DIR < 0 ? Y_MIN_POS : Y_MAX_POS)
#endif
#endif
#ifdef MANUAL_Z_HOME_POS
#define Z_HOME_POS MANUAL_Z_HOME_POS
#else
#define Z_HOME_POS (Z_HOME_DIR < 0 ? Z_MIN_POS : Z_MAX_POS)
#endif
/**
* If DELTA_HEIGHT isn't defined use the old setting
*/
#if ENABLED(DELTA) && !defined(DELTA_HEIGHT)
#define DELTA_HEIGHT Z_HOME_POS
#endif
/**
* Auto Bed Leveling and Z Probe Repeatability Test
*/
#define HOMING_Z_WITH_PROBE (HAS_BED_PROBE && Z_HOME_DIR < 0 && ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN))
/**
* Z Sled Probe requires Z_SAFE_HOMING
*/
#if ENABLED(Z_PROBE_SLED)
#define Z_SAFE_HOMING
#endif
/**
* DELTA should ignore Z_SAFE_HOMING and SLOWDOWN
*/
#if ENABLED(DELTA)
#undef Z_SAFE_HOMING
#undef SLOWDOWN
#endif
/**
* Safe Homing Options
*/
#if ENABLED(Z_SAFE_HOMING)
#ifndef Z_SAFE_HOMING_X_POINT
#define Z_SAFE_HOMING_X_POINT X_CENTER
#endif
#ifndef Z_SAFE_HOMING_Y_POINT
#define Z_SAFE_HOMING_Y_POINT Y_CENTER
#endif
#define X_TILT_FULCRUM Z_SAFE_HOMING_X_POINT
#define Y_TILT_FULCRUM Z_SAFE_HOMING_Y_POINT
#else
#define X_TILT_FULCRUM X_HOME_POS
#define Y_TILT_FULCRUM Y_HOME_POS
#endif
/**
* Host keep alive
*/
#ifndef DEFAULT_KEEPALIVE_INTERVAL
#define DEFAULT_KEEPALIVE_INTERVAL 2
#endif
/**
* Provide a MAX_AUTORETRACT for older configs
*/
#if ENABLED(FWRETRACT) && !defined(MAX_AUTORETRACT)
#define MAX_AUTORETRACT 99
#endif
/**
* MAX_STEP_FREQUENCY differs for TOSHIBA
*/
#if ENABLED(CONFIG_STEPPERS_TOSHIBA)
#define MAX_STEP_FREQUENCY 10000 // Max step frequency for Toshiba Stepper Controllers
#else
#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
#endif
// MS1 MS2 Stepper Driver Microstepping mode table
#define MICROSTEP1 LOW,LOW
#define MICROSTEP2 HIGH,LOW
#define MICROSTEP4 LOW,HIGH
#define MICROSTEP8 HIGH,HIGH
#define MICROSTEP16 HIGH,HIGH
/**
* Advance calculated values
*/
#if ENABLED(ADVANCE)
#define EXTRUSION_AREA (0.25 * (D_FILAMENT) * (D_FILAMENT) * M_PI)
#define STEPS_PER_CUBIC_MM_E (axis_steps_per_mm[E_AXIS_N] / (EXTRUSION_AREA))
#endif
#if ENABLED(ULTIPANEL) && DISABLED(ELB_FULL_GRAPHIC_CONTROLLER)
#undef SD_DETECT_INVERTED
#endif
/**
* Set defaults for missing (newer) options
*/
#ifndef DISABLE_INACTIVE_X
#define DISABLE_INACTIVE_X DISABLE_X
#endif
#ifndef DISABLE_INACTIVE_Y
#define DISABLE_INACTIVE_Y DISABLE_Y
#endif
#ifndef DISABLE_INACTIVE_Z
#define DISABLE_INACTIVE_Z DISABLE_Z
#endif
#ifndef DISABLE_INACTIVE_E
#define DISABLE_INACTIVE_E DISABLE_E
#endif
// Power Signal Control Definitions
// By default use ATX definition
#ifndef POWER_SUPPLY
#define POWER_SUPPLY 1
#endif
#if (POWER_SUPPLY == 1) // 1 = ATX
#define PS_ON_AWAKE LOW
#define PS_ON_ASLEEP HIGH
#elif (POWER_SUPPLY == 2) // 2 = X-Box 360 203W
#define PS_ON_AWAKE HIGH
#define PS_ON_ASLEEP LOW
#endif
#define HAS_POWER_SWITCH (POWER_SUPPLY > 0 && PIN_EXISTS(PS_ON))
/**
* Temp Sensor defines
*/
#if TEMP_SENSOR_0 == -3
#define HEATER_0_USES_MAX6675
#define MAX6675_IS_MAX31855
#define MAX6675_TMIN -270
#define MAX6675_TMAX 1800
#elif TEMP_SENSOR_0 == -2
#define HEATER_0_USES_MAX6675
#define MAX6675_TMIN 0
#define MAX6675_TMAX 1024
#elif TEMP_SENSOR_0 == -1
#define HEATER_0_USES_AD595
#elif TEMP_SENSOR_0 == 0
#undef HEATER_0_MINTEMP
#undef HEATER_0_MAXTEMP
#elif TEMP_SENSOR_0 > 0
#define THERMISTORHEATER_0 TEMP_SENSOR_0
#define HEATER_0_USES_THERMISTOR
#endif
#if TEMP_SENSOR_1 <= -2
#error "MAX6675 / MAX31855 Thermocouples not supported for TEMP_SENSOR_1"
#elif TEMP_SENSOR_1 == -1
#define HEATER_1_USES_AD595
#elif TEMP_SENSOR_1 == 0
#undef HEATER_1_MINTEMP
#undef HEATER_1_MAXTEMP
#elif TEMP_SENSOR_1 > 0
#define THERMISTORHEATER_1 TEMP_SENSOR_1
#define HEATER_1_USES_THERMISTOR
#endif
#if TEMP_SENSOR_2 <= -2
#error "MAX6675 / MAX31855 Thermocouples not supported for TEMP_SENSOR_2"
#elif TEMP_SENSOR_2 == -1
#define HEATER_2_USES_AD595
#elif TEMP_SENSOR_2 == 0
#undef HEATER_2_MINTEMP
#undef HEATER_2_MAXTEMP
#elif TEMP_SENSOR_2 > 0
#define THERMISTORHEATER_2 TEMP_SENSOR_2
#define HEATER_2_USES_THERMISTOR
#endif
#if TEMP_SENSOR_3 <= -2
#error "MAX6675 / MAX31855 Thermocouples not supported for TEMP_SENSOR_3"
#elif TEMP_SENSOR_3 == -1
#define HEATER_3_USES_AD595
#elif TEMP_SENSOR_3 == 0
#undef HEATER_3_MINTEMP
#undef HEATER_3_MAXTEMP
#elif TEMP_SENSOR_3 > 0
#define THERMISTORHEATER_3 TEMP_SENSOR_3
#define HEATER_3_USES_THERMISTOR
#endif
#if TEMP_SENSOR_4 <= -2
#error "MAX6675 / MAX31855 Thermocouples not supported for TEMP_SENSOR_4"
#elif TEMP_SENSOR_4 == -1
#define HEATER_4_USES_AD595
#elif TEMP_SENSOR_4 == 0
#undef HEATER_4_MINTEMP
#undef HEATER_4_MAXTEMP
#elif TEMP_SENSOR_4 > 0
#define THERMISTORHEATER_4 TEMP_SENSOR_4
#define HEATER_4_USES_THERMISTOR
#endif
#if TEMP_SENSOR_BED <= -2
#error "MAX6675 / MAX31855 Thermocouples not supported for TEMP_SENSOR_BED"
#elif TEMP_SENSOR_BED == -1
#define BED_USES_AD595
#elif TEMP_SENSOR_BED == 0
#undef BED_MINTEMP
#undef BED_MAXTEMP
#elif TEMP_SENSOR_BED > 0
#define THERMISTORBED TEMP_SENSOR_BED
#define BED_USES_THERMISTOR
#endif
/**
* Flags for PID handling
*/
#define HAS_PID_HEATING (ENABLED(PIDTEMP) || ENABLED(PIDTEMPBED))
#define HAS_PID_FOR_BOTH (ENABLED(PIDTEMP) && ENABLED(PIDTEMPBED))
/**
* Default hotend offsets, if not defined
*/
#if HOTENDS > 1
#ifndef HOTEND_OFFSET_X
#define HOTEND_OFFSET_X { 0 } // X offsets for each extruder
#endif
#ifndef HOTEND_OFFSET_Y
#define HOTEND_OFFSET_Y { 0 } // Y offsets for each extruder
#endif
#if !defined(HOTEND_OFFSET_Z) && (ENABLED(DUAL_X_CARRIAGE) || ENABLED(SWITCHING_NOZZLE))
#define HOTEND_OFFSET_Z { 0 }
#endif
#endif
/**
* ARRAY_BY_EXTRUDERS based on EXTRUDERS
*/
#define ARRAY_BY_EXTRUDERS(...) ARRAY_N(EXTRUDERS, __VA_ARGS__)
#define ARRAY_BY_EXTRUDERS1(v1) ARRAY_BY_EXTRUDERS(v1, v1, v1, v1, v1, v1)
/**
* ARRAY_BY_HOTENDS based on HOTENDS
*/
#define ARRAY_BY_HOTENDS(...) ARRAY_N(HOTENDS, __VA_ARGS__)
#define ARRAY_BY_HOTENDS1(v1) ARRAY_BY_HOTENDS(v1, v1, v1, v1, v1, v1)
/**
* Z_DUAL_ENDSTOPS endstop reassignment
*/
#if ENABLED(Z_DUAL_ENDSTOPS)
#define _XMIN_ 100
#define _YMIN_ 200
#define _ZMIN_ 300
#define _XMAX_ 101
#define _YMAX_ 201
#define _ZMAX_ 301
#if Z2_USE_ENDSTOP == _XMIN_
#define USE_XMIN_PLUG
#elif Z2_USE_ENDSTOP == _XMAX_
#define USE_XMAX_PLUG
#elif Z2_USE_ENDSTOP == _YMIN_
#define USE_YMIN_PLUG
#elif Z2_USE_ENDSTOP == _YMAX_
#define USE_YMAX_PLUG
#elif Z2_USE_ENDSTOP == _ZMIN_
#define USE_ZMIN_PLUG
#elif Z2_USE_ENDSTOP == _ZMAX_
#define USE_ZMAX_PLUG
#endif
#if Z_HOME_DIR > 0
#if Z2_USE_ENDSTOP == _XMIN_
#define Z2_MAX_ENDSTOP_INVERTING X_MIN_ENDSTOP_INVERTING
#define Z2_MAX_PIN X_MIN_PIN
#elif Z2_USE_ENDSTOP == _XMAX_
#define Z2_MAX_ENDSTOP_INVERTING X_MAX_ENDSTOP_INVERTING
#define Z2_MAX_PIN X_MAX_PIN
#elif Z2_USE_ENDSTOP == _YMIN_
#define Z2_MAX_ENDSTOP_INVERTING Y_MIN_ENDSTOP_INVERTING
#define Z2_MAX_PIN Y_MIN_PIN
#elif Z2_USE_ENDSTOP == _YMAX_
#define Z2_MAX_ENDSTOP_INVERTING Y_MAX_ENDSTOP_INVERTING
#define Z2_MAX_PIN Y_MAX_PIN
#elif Z2_USE_ENDSTOP == _ZMIN_
#define Z2_MAX_ENDSTOP_INVERTING Z_MIN_ENDSTOP_INVERTING
#define Z2_MAX_PIN Z_MIN_PIN
#elif Z2_USE_ENDSTOP == _ZMAX_
#define Z2_MAX_ENDSTOP_INVERTING Z_MAX_ENDSTOP_INVERTING
#define Z2_MAX_PIN Z_MAX_PIN
#else
#define Z2_MAX_ENDSTOP_INVERTING false
#endif
#else
#if Z2_USE_ENDSTOP == _XMIN_
#define Z2_MIN_ENDSTOP_INVERTING X_MIN_ENDSTOP_INVERTING
#define Z2_MIN_PIN X_MIN_PIN
#elif Z2_USE_ENDSTOP == _XMAX_
#define Z2_MIN_ENDSTOP_INVERTING X_MAX_ENDSTOP_INVERTING
#define Z2_MIN_PIN X_MAX_PIN
#elif Z2_USE_ENDSTOP == _YMIN_
#define Z2_MIN_ENDSTOP_INVERTING Y_MIN_ENDSTOP_INVERTING
#define Z2_MIN_PIN Y_MIN_PIN
#elif Z2_USE_ENDSTOP == _YMAX_
#define Z2_MIN_ENDSTOP_INVERTING Y_MAX_ENDSTOP_INVERTING
#define Z2_MIN_PIN Y_MAX_PIN
#elif Z2_USE_ENDSTOP == _ZMIN_
#define Z2_MIN_ENDSTOP_INVERTING Z_MIN_ENDSTOP_INVERTING
#define Z2_MIN_PIN Z_MIN_PIN
#elif Z2_USE_ENDSTOP == _ZMAX_
#define Z2_MIN_ENDSTOP_INVERTING Z_MAX_ENDSTOP_INVERTING
#define Z2_MIN_PIN Z_MAX_PIN
#else
#define Z2_MIN_ENDSTOP_INVERTING false
#endif
#endif
#endif
// Is an endstop plug used for the Z2 endstop or the bed probe?
#define IS_Z2_OR_PROBE(A,M) ( \
(ENABLED(Z_DUAL_ENDSTOPS) && Z2_USE_ENDSTOP == _##A##M##_) \
|| (ENABLED(Z_MIN_PROBE_ENDSTOP) && Z_MIN_PROBE_PIN == A##_##M##_PIN ) )
/**
* Set ENDSTOPPULLUPS for active endstop switches
*/
#if ENABLED(ENDSTOPPULLUPS)
#if ENABLED(USE_XMAX_PLUG)
#define ENDSTOPPULLUP_XMAX
#endif
#if ENABLED(USE_YMAX_PLUG)
#define ENDSTOPPULLUP_YMAX
#endif
#if ENABLED(USE_ZMAX_PLUG)
#define ENDSTOPPULLUP_ZMAX
#endif
#if ENABLED(USE_XMIN_PLUG)
#define ENDSTOPPULLUP_XMIN
#endif
#if ENABLED(USE_YMIN_PLUG)
#define ENDSTOPPULLUP_YMIN
#endif
#if ENABLED(USE_ZMIN_PLUG)
#define ENDSTOPPULLUP_ZMIN
#endif
#endif
/**
* Shorthand for pin tests, used wherever needed
*/
// Steppers
#define HAS_X_ENABLE (PIN_EXISTS(X_ENABLE))
#define HAS_X_DIR (PIN_EXISTS(X_DIR))
#define HAS_X_STEP (PIN_EXISTS(X_STEP))
#define HAS_X_MICROSTEPS (PIN_EXISTS(X_MS1))
#define HAS_X2_ENABLE (PIN_EXISTS(X2_ENABLE))
#define HAS_X2_DIR (PIN_EXISTS(X2_DIR))
#define HAS_X2_STEP (PIN_EXISTS(X2_STEP))
#define HAS_Y_MICROSTEPS (PIN_EXISTS(Y_MS1))
#define HAS_Y_ENABLE (PIN_EXISTS(Y_ENABLE))
#define HAS_Y_DIR (PIN_EXISTS(Y_DIR))
#define HAS_Y_STEP (PIN_EXISTS(Y_STEP))
#define HAS_Z_MICROSTEPS (PIN_EXISTS(Z_MS1))
#define HAS_Y2_ENABLE (PIN_EXISTS(Y2_ENABLE))
#define HAS_Y2_DIR (PIN_EXISTS(Y2_DIR))
#define HAS_Y2_STEP (PIN_EXISTS(Y2_STEP))
#define HAS_Z_ENABLE (PIN_EXISTS(Z_ENABLE))
#define HAS_Z_DIR (PIN_EXISTS(Z_DIR))
#define HAS_Z_STEP (PIN_EXISTS(Z_STEP))
#define HAS_Z2_ENABLE (PIN_EXISTS(Z2_ENABLE))
#define HAS_Z2_DIR (PIN_EXISTS(Z2_DIR))
#define HAS_Z2_STEP (PIN_EXISTS(Z2_STEP))
// Extruder steppers and solenoids
#define HAS_E0_ENABLE (PIN_EXISTS(E0_ENABLE))
#define HAS_E0_DIR (PIN_EXISTS(E0_DIR))
#define HAS_E0_STEP (PIN_EXISTS(E0_STEP))
#define HAS_E0_MICROSTEPS (PIN_EXISTS(E0_MS1))
#define HAS_SOLENOID_0 (PIN_EXISTS(SOL0))
#define HAS_E1_ENABLE (PIN_EXISTS(E1_ENABLE))
#define HAS_E1_DIR (PIN_EXISTS(E1_DIR))
#define HAS_E1_STEP (PIN_EXISTS(E1_STEP))
#define HAS_E1_MICROSTEPS (PIN_EXISTS(E1_MS1))
#define HAS_SOLENOID_1 (PIN_EXISTS(SOL1))
#define HAS_E2_ENABLE (PIN_EXISTS(E2_ENABLE))
#define HAS_E2_DIR (PIN_EXISTS(E2_DIR))
#define HAS_E2_STEP (PIN_EXISTS(E2_STEP))
#define HAS_E2_MICROSTEPS (PIN_EXISTS(E2_MS1))
#define HAS_SOLENOID_2 (PIN_EXISTS(SOL2))
#define HAS_E3_ENABLE (PIN_EXISTS(E3_ENABLE))
#define HAS_E3_DIR (PIN_EXISTS(E3_DIR))
#define HAS_E3_STEP (PIN_EXISTS(E3_STEP))
#define HAS_E3_MICROSTEPS (PIN_EXISTS(E3_MS1))
#define HAS_SOLENOID_3 (PIN_EXISTS(SOL3))
#define HAS_E4_ENABLE (PIN_EXISTS(E4_ENABLE))
#define HAS_E4_DIR (PIN_EXISTS(E4_DIR))
#define HAS_E4_STEP (PIN_EXISTS(E4_STEP))
#define HAS_E4_MICROSTEPS (PIN_EXISTS(E4_MS1))
#define HAS_SOLENOID_4 (PIN_EXISTS(SOL4))
// Endstops and bed probe
#define HAS_X_MIN (PIN_EXISTS(X_MIN) && !IS_Z2_OR_PROBE(X,MIN))
#define HAS_X_MAX (PIN_EXISTS(X_MAX) && !IS_Z2_OR_PROBE(X,MAX))
#define HAS_Y_MIN (PIN_EXISTS(Y_MIN) && !IS_Z2_OR_PROBE(Y,MIN))
#define HAS_Y_MAX (PIN_EXISTS(Y_MAX) && !IS_Z2_OR_PROBE(Y,MAX))
#define HAS_Z_MIN (PIN_EXISTS(Z_MIN) && !IS_Z2_OR_PROBE(Z,MIN))
#define HAS_Z_MAX (PIN_EXISTS(Z_MAX) && !IS_Z2_OR_PROBE(Z,MAX))
#define HAS_Z2_MIN (PIN_EXISTS(Z2_MIN))
#define HAS_Z2_MAX (PIN_EXISTS(Z2_MAX))
#define HAS_Z_MIN_PROBE_PIN (PIN_EXISTS(Z_MIN_PROBE))
// Thermistors
#define HAS_TEMP_0 (PIN_EXISTS(TEMP_0) && TEMP_SENSOR_0 != 0 && TEMP_SENSOR_0 > -2)
#define HAS_TEMP_1 (PIN_EXISTS(TEMP_1) && TEMP_SENSOR_1 != 0 && TEMP_SENSOR_1 > -2)
#define HAS_TEMP_2 (PIN_EXISTS(TEMP_2) && TEMP_SENSOR_2 != 0 && TEMP_SENSOR_2 > -2)
#define HAS_TEMP_3 (PIN_EXISTS(TEMP_3) && TEMP_SENSOR_3 != 0 && TEMP_SENSOR_3 > -2)
#define HAS_TEMP_4 (PIN_EXISTS(TEMP_4) && TEMP_SENSOR_4 != 0 && TEMP_SENSOR_4 > -2)
#define HAS_TEMP_HOTEND (HAS_TEMP_0 || ENABLED(HEATER_0_USES_MAX6675))
#define HAS_TEMP_BED (PIN_EXISTS(TEMP_BED) && TEMP_SENSOR_BED != 0 && TEMP_SENSOR_BED > -2)
// Heaters
#define HAS_HEATER_0 (PIN_EXISTS(HEATER_0))
#define HAS_HEATER_1 (PIN_EXISTS(HEATER_1))
#define HAS_HEATER_2 (PIN_EXISTS(HEATER_2))
#define HAS_HEATER_3 (PIN_EXISTS(HEATER_3))
#define HAS_HEATER_4 (PIN_EXISTS(HEATER_4))
#define HAS_HEATER_BED (PIN_EXISTS(HEATER_BED))
// Thermal protection
#define HAS_THERMALLY_PROTECTED_BED (ENABLED(THERMAL_PROTECTION_BED) && HAS_TEMP_BED && HAS_HEATER_BED)
#define WATCH_HOTENDS (ENABLED(THERMAL_PROTECTION_HOTENDS) && WATCH_TEMP_PERIOD > 0)
#define WATCH_THE_BED (HAS_THERMALLY_PROTECTED_BED && WATCH_BED_TEMP_PERIOD > 0)
// Auto fans
#define HAS_AUTO_FAN_0 (PIN_EXISTS(E0_AUTO_FAN))
#define HAS_AUTO_FAN_1 (HOTENDS > 1 && PIN_EXISTS(E1_AUTO_FAN))
#define HAS_AUTO_FAN_2 (HOTENDS > 2 && PIN_EXISTS(E2_AUTO_FAN))
#define HAS_AUTO_FAN_3 (HOTENDS > 3 && PIN_EXISTS(E3_AUTO_FAN))
#define HAS_AUTO_FAN_4 (HOTENDS > 4 && PIN_EXISTS(E4_AUTO_FAN))
#define HAS_AUTO_FAN (HAS_AUTO_FAN_0 || HAS_AUTO_FAN_1 || HAS_AUTO_FAN_2 || HAS_AUTO_FAN_3)
#define AUTO_1_IS_0 (E1_AUTO_FAN_PIN == E0_AUTO_FAN_PIN)
#define AUTO_2_IS_0 (E2_AUTO_FAN_PIN == E0_AUTO_FAN_PIN)
#define AUTO_2_IS_1 (E2_AUTO_FAN_PIN == E1_AUTO_FAN_PIN)
#define AUTO_3_IS_0 (E3_AUTO_FAN_PIN == E0_AUTO_FAN_PIN)
#define AUTO_3_IS_1 (E3_AUTO_FAN_PIN == E1_AUTO_FAN_PIN)
#define AUTO_3_IS_2 (E3_AUTO_FAN_PIN == E2_AUTO_FAN_PIN)
#define AUTO_4_IS_0 (E4_AUTO_FAN_PIN == E0_AUTO_FAN_PIN)
#define AUTO_4_IS_1 (E4_AUTO_FAN_PIN == E1_AUTO_FAN_PIN)
#define AUTO_4_IS_2 (E4_AUTO_FAN_PIN == E2_AUTO_FAN_PIN)
#define AUTO_4_IS_3 (E4_AUTO_FAN_PIN == E3_AUTO_FAN_PIN)
// Other fans
#define HAS_FAN0 (PIN_EXISTS(FAN))
#define HAS_FAN1 (PIN_EXISTS(FAN1) && CONTROLLER_FAN_PIN != FAN1_PIN && E0_AUTO_FAN_PIN != FAN1_PIN && E1_AUTO_FAN_PIN != FAN1_PIN && E2_AUTO_FAN_PIN != FAN1_PIN && E3_AUTO_FAN_PIN != FAN1_PIN)
#define HAS_FAN2 (PIN_EXISTS(FAN2) && CONTROLLER_FAN_PIN != FAN2_PIN && E0_AUTO_FAN_PIN != FAN2_PIN && E1_AUTO_FAN_PIN != FAN2_PIN && E2_AUTO_FAN_PIN != FAN2_PIN && E3_AUTO_FAN_PIN != FAN2_PIN)
#define HAS_CONTROLLER_FAN (PIN_EXISTS(CONTROLLER_FAN))
// Servos
#define HAS_SERVOS (defined(NUM_SERVOS) && NUM_SERVOS > 0)
#define HAS_SERVO_0 (PIN_EXISTS(SERVO0))
#define HAS_SERVO_1 (PIN_EXISTS(SERVO1))
#define HAS_SERVO_2 (PIN_EXISTS(SERVO2))
#define HAS_SERVO_3 (PIN_EXISTS(SERVO3))
// Sensors
#define HAS_FILAMENT_WIDTH_SENSOR (PIN_EXISTS(FILWIDTH))
#define HAS_FIL_RUNOUT (PIN_EXISTS(FIL_RUNOUT))
// User Interface
#define HAS_HOME (PIN_EXISTS(HOME))
#define HAS_KILL (PIN_EXISTS(KILL))
#define HAS_SUICIDE (PIN_EXISTS(SUICIDE))
#define HAS_PHOTOGRAPH (PIN_EXISTS(PHOTOGRAPH))
#define HAS_BUZZER (PIN_EXISTS(BEEPER) || ENABLED(LCD_USE_I2C_BUZZER))
#define HAS_CASE_LIGHT (PIN_EXISTS(CASE_LIGHT) && ENABLED(CASE_LIGHT_ENABLE))
// Digital control
#define HAS_MICROSTEPS (HAS_X_MICROSTEPS || HAS_Y_MICROSTEPS || HAS_Z_MICROSTEPS || HAS_E0_MICROSTEPS || HAS_E1_MICROSTEPS || HAS_E2_MICROSTEPS || HAS_E3_MICROSTEPS || HAS_E4_MICROSTEPS)
#define HAS_STEPPER_RESET (PIN_EXISTS(STEPPER_RESET))
#define HAS_DIGIPOTSS (PIN_EXISTS(DIGIPOTSS))
#define HAS_MOTOR_CURRENT_PWM (PIN_EXISTS(MOTOR_CURRENT_PWM_XY) || PIN_EXISTS(MOTOR_CURRENT_PWM_Z) || PIN_EXISTS(MOTOR_CURRENT_PWM_E))
/**
* This setting is also used by M109 when trying to calculate
* a ballpark safe margin to prevent wait-forever situation.
*/
#ifndef EXTRUDE_MINTEMP
#define EXTRUDE_MINTEMP 170
#endif
/**
* Helper Macros for heaters and extruder fan
*/
#define WRITE_HEATER_0P(v) WRITE(HEATER_0_PIN, v)
#if HOTENDS > 1 || ENABLED(HEATERS_PARALLEL)
#define WRITE_HEATER_1(v) WRITE(HEATER_1_PIN, v)
#if HOTENDS > 2
#define WRITE_HEATER_2(v) WRITE(HEATER_2_PIN, v)
#if HOTENDS > 3
#define WRITE_HEATER_3(v) WRITE(HEATER_3_PIN, v)
#if HOTENDS > 4
#define WRITE_HEATER_4(v) WRITE(HEATER_4_PIN, v)
#endif // HOTENDS > 4
#endif // HOTENDS > 3
#endif // HOTENDS > 2
#endif // HOTENDS > 1
#if ENABLED(HEATERS_PARALLEL)
#define WRITE_HEATER_0(v) { WRITE_HEATER_0P(v); WRITE_HEATER_1(v); }
#else
#define WRITE_HEATER_0(v) WRITE_HEATER_0P(v)
#endif
/**
* Heated bed requires settings
*/
#if HAS_HEATER_BED
#ifndef MAX_BED_POWER
#define MAX_BED_POWER 255
#endif
#ifndef HEATER_BED_INVERTING
#define HEATER_BED_INVERTING false
#endif
#define WRITE_HEATER_BED(v) WRITE(HEATER_BED_PIN, (v) ^ HEATER_BED_INVERTING)
#endif
/**
* Up to 3 PWM fans
*/
#if HAS_FAN2
#define FAN_COUNT 3
#elif HAS_FAN1
#define FAN_COUNT 2
#elif HAS_FAN0
#define FAN_COUNT 1
#else
#define FAN_COUNT 0
#endif
#if HAS_FAN0
#define WRITE_FAN(v) WRITE(FAN_PIN, v)
#define WRITE_FAN0(v) WRITE_FAN(v)
#endif
#if HAS_FAN1
#define WRITE_FAN1(v) WRITE(FAN1_PIN, v)
#endif
#if HAS_FAN2
#define WRITE_FAN2(v) WRITE(FAN2_PIN, v)
#endif
#define WRITE_FAN_N(n, v) WRITE_FAN##n(v)
/**
* Part Cooling fan multipliexer
*/
#define HAS_FANMUX PIN_EXISTS(FANMUX0)
/**
* Servos and probes
*/
#if HAS_SERVOS
#ifndef Z_ENDSTOP_SERVO_NR
#define Z_ENDSTOP_SERVO_NR -1
#endif
#endif
#define PROBE_PIN_CONFIGURED (HAS_Z_MIN_PROBE_PIN || (HAS_Z_MIN && ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)))
#define HAS_BED_PROBE (PROBE_SELECTED && PROBE_PIN_CONFIGURED && DISABLED(PROBE_MANUALLY))
#if ENABLED(Z_PROBE_ALLEN_KEY)
#define PROBE_IS_TRIGGERED_WHEN_STOWED_TEST
#endif
/**
* Bed Probe dependencies
*/
#if HAS_BED_PROBE
#if ENABLED(ENDSTOPPULLUPS) && HAS_Z_MIN_PROBE_PIN
#define ENDSTOPPULLUP_ZMIN_PROBE
#endif
#ifndef Z_PROBE_OFFSET_RANGE_MIN
#define Z_PROBE_OFFSET_RANGE_MIN -20
#endif
#ifndef Z_PROBE_OFFSET_RANGE_MAX
#define Z_PROBE_OFFSET_RANGE_MAX 20
#endif
#ifndef XY_PROBE_SPEED
#ifdef HOMING_FEEDRATE_XY
#define XY_PROBE_SPEED HOMING_FEEDRATE_XY
#else
#define XY_PROBE_SPEED 4000
#endif
#endif
#if Z_CLEARANCE_BETWEEN_PROBES > Z_CLEARANCE_DEPLOY_PROBE
#define _Z_CLEARANCE_DEPLOY_PROBE Z_CLEARANCE_BETWEEN_PROBES
#else
#define _Z_CLEARANCE_DEPLOY_PROBE Z_CLEARANCE_DEPLOY_PROBE
#endif
#else
#undef X_PROBE_OFFSET_FROM_EXTRUDER
#undef Y_PROBE_OFFSET_FROM_EXTRUDER
#undef Z_PROBE_OFFSET_FROM_EXTRUDER
#define X_PROBE_OFFSET_FROM_EXTRUDER 0
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0
#endif
/**
* Heater & Fan Pausing
*/
#if FAN_COUNT == 0
#undef PROBING_FANS_OFF
#endif
#define QUIET_PROBING (HAS_BED_PROBE && (ENABLED(PROBING_HEATERS_OFF) || ENABLED(PROBING_FANS_OFF) || DELAY_BEFORE_PROBING > 0))
#define HEATER_IDLE_HANDLER (ENABLED(ADVANCED_PAUSE_FEATURE) || ENABLED(PROBING_HEATERS_OFF))
/**
* Delta radius/rod trimmers/angle trimmers
*/
#if ENABLED(DELTA)
#ifndef DELTA_CALIBRATION_RADIUS
#define DELTA_CALIBRATION_RADIUS DELTA_PRINTABLE_RADIUS - 10
#endif
#ifndef DELTA_ENDSTOP_ADJ
#define DELTA_ENDSTOP_ADJ { 0, 0, 0 }
#endif
#ifndef DELTA_TOWER_ANGLE_TRIM
#define DELTA_TOWER_ANGLE_TRIM {0, 0, 0}
#endif
#ifndef DELTA_RADIUS_TRIM_TOWER
#define DELTA_RADIUS_TRIM_TOWER {0, 0, 0}
#endif
#ifndef DELTA_DIAGONAL_ROD_TRIM_TOWER
#define DELTA_DIAGONAL_ROD_TRIM_TOWER {0, 0, 0}
#endif
#endif
/**
* Set granular options based on the specific type of leveling
*/
#define UBL_DELTA (ENABLED(AUTO_BED_LEVELING_UBL) && (ENABLED(DELTA) || ENABLED(UBL_GRANULAR_SEGMENTATION_FOR_CARTESIAN)))
#define ABL_PLANAR (ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_3POINT))
#define ABL_GRID (ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR))
#define HAS_ABL (ABL_PLANAR || ABL_GRID || ENABLED(AUTO_BED_LEVELING_UBL))
#define HAS_LEVELING (HAS_ABL || ENABLED(MESH_BED_LEVELING))
#define PLANNER_LEVELING (ABL_PLANAR || ABL_GRID || ENABLED(MESH_BED_LEVELING) || UBL_DELTA)
#define HAS_PROBING_PROCEDURE (HAS_ABL || ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST))
#if HAS_PROBING_PROCEDURE
#define PROBE_BED_WIDTH abs(RIGHT_PROBE_BED_POSITION - (LEFT_PROBE_BED_POSITION))
#define PROBE_BED_HEIGHT abs(BACK_PROBE_BED_POSITION - (FRONT_PROBE_BED_POSITION))
#endif
/**
* Buzzer/Speaker
*/
#if ENABLED(LCD_USE_I2C_BUZZER)
#ifndef LCD_FEEDBACK_FREQUENCY_HZ
#define LCD_FEEDBACK_FREQUENCY_HZ 1000
#endif
#ifndef LCD_FEEDBACK_FREQUENCY_DURATION_MS
#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
#endif
#else
#ifndef LCD_FEEDBACK_FREQUENCY_HZ
#define LCD_FEEDBACK_FREQUENCY_HZ 5000
#endif
#ifndef LCD_FEEDBACK_FREQUENCY_DURATION_MS
#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
#endif
#endif
/**
* Z_HOMING_HEIGHT / Z_CLEARANCE_BETWEEN_PROBES
*/
#ifndef Z_HOMING_HEIGHT
#ifndef Z_CLEARANCE_BETWEEN_PROBES
#define Z_HOMING_HEIGHT 0
#else
#define Z_HOMING_HEIGHT Z_CLEARANCE_BETWEEN_PROBES
#endif
#endif
#ifndef Z_CLEARANCE_BETWEEN_PROBES
#define Z_CLEARANCE_BETWEEN_PROBES Z_HOMING_HEIGHT
#endif
#if Z_CLEARANCE_BETWEEN_PROBES > Z_HOMING_HEIGHT
#define MANUAL_PROBE_HEIGHT Z_CLEARANCE_BETWEEN_PROBES
#else
#define MANUAL_PROBE_HEIGHT Z_HOMING_HEIGHT
#endif
/**
* Bed Probing rectangular bounds
* These can be further constrained in code for Delta and SCARA
*/
#if ENABLED(DELTA)
#ifndef DELTA_PROBEABLE_RADIUS
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
#endif
// Probing points may be verified at compile time within the radius
// using static_assert(HYPOT2(X2-X1,Y2-Y1)<=sq(DELTA_PRINTABLE_RADIUS),"bad probe point!")
// so that may be added to SanityCheck.h in the future.
#define MIN_PROBE_X (X_CENTER - (DELTA_PROBEABLE_RADIUS))
#define MIN_PROBE_Y (Y_CENTER - (DELTA_PROBEABLE_RADIUS))
#define MAX_PROBE_X (X_CENTER + DELTA_PROBEABLE_RADIUS)
#define MAX_PROBE_Y (Y_CENTER + DELTA_PROBEABLE_RADIUS)
#elif IS_SCARA
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#define MIN_PROBE_X (X_CENTER - (SCARA_PRINTABLE_RADIUS))
#define MIN_PROBE_Y (Y_CENTER - (SCARA_PRINTABLE_RADIUS))
#define MAX_PROBE_X (X_CENTER + SCARA_PRINTABLE_RADIUS)
#define MAX_PROBE_Y (Y_CENTER + SCARA_PRINTABLE_RADIUS)
#else
// Boundaries for Cartesian probing based on set limits
#if ENABLED(LULZBOT_PROBE_POINTS_OUTSIDE_OF_BED)
#define MIN_PROBE_X (X_MIN_POS)
#define MIN_PROBE_Y (Y_MIN_POS)
#define MAX_PROBE_X (X_MAX_POS)
#define MAX_PROBE_Y (Y_MAX_POS)
#elif ENABLED(BED_CENTER_AT_0_0)
#define MIN_PROBE_X (max(X_PROBE_OFFSET_FROM_EXTRUDER, 0) - (X_BED_SIZE) / 2)
#define MIN_PROBE_Y (max(Y_PROBE_OFFSET_FROM_EXTRUDER, 0) - (Y_BED_SIZE) / 2)
#define MAX_PROBE_X (min(X_BED_SIZE + X_PROBE_OFFSET_FROM_EXTRUDER, X_BED_SIZE) - (X_BED_SIZE) / 2)
#define MAX_PROBE_Y (min(Y_BED_SIZE + Y_PROBE_OFFSET_FROM_EXTRUDER, Y_BED_SIZE) - (Y_BED_SIZE) / 2)
#else
#define MIN_PROBE_X (max(X_MIN_POS + X_PROBE_OFFSET_FROM_EXTRUDER, 0))
#define MIN_PROBE_Y (max(Y_MIN_POS + Y_PROBE_OFFSET_FROM_EXTRUDER, 0))
#define MAX_PROBE_X (min(X_MAX_POS + X_PROBE_OFFSET_FROM_EXTRUDER, X_BED_SIZE))
#define MAX_PROBE_Y (min(Y_MAX_POS + Y_PROBE_OFFSET_FROM_EXTRUDER, Y_BED_SIZE))
#endif
#endif
// Stepper pulse duration, in cycles
#define STEP_PULSE_CYCLES ((MINIMUM_STEPPER_PULSE) * CYCLES_PER_MICROSECOND)
#if ENABLED(SDCARD_SORT_ALPHA)
#define HAS_FOLDER_SORTING (FOLDER_SORTING || ENABLED(SDSORT_GCODE))
#endif
// Updated G92 behavior shifts the workspace
#define HAS_POSITION_SHIFT DISABLED(NO_WORKSPACE_OFFSETS)
// The home offset also shifts the coordinate space
#define HAS_HOME_OFFSET (DISABLED(NO_WORKSPACE_OFFSETS) || ENABLED(DELTA))
// Either offset yields extra calculations on all moves
#define HAS_WORKSPACE_OFFSET (HAS_POSITION_SHIFT || HAS_HOME_OFFSET)
// M206 doesn't apply to DELTA
#define HAS_M206_COMMAND (HAS_HOME_OFFSET && DISABLED(DELTA))
// LCD timeout to status screen default is 15s
#ifndef LCD_TIMEOUT_TO_STATUS
#define LCD_TIMEOUT_TO_STATUS 15000
#endif
/**
* DELTA_SEGMENT_MIN_LENGTH for UBL_DELTA
*/
#if UBL_DELTA
#ifndef DELTA_SEGMENT_MIN_LENGTH
#if IS_SCARA
#define DELTA_SEGMENT_MIN_LENGTH 0.25 // SCARA minimum segment size is 0.25mm
#elif ENABLED(DELTA)
#define DELTA_SEGMENT_MIN_LENGTH 0.10 // mm (still subject to DELTA_SEGMENTS_PER_SECOND)
#else // CARTESIAN
#define DELTA_SEGMENT_MIN_LENGTH 1.00 // mm (similar to G2/G3 arc segmentation)
#endif
#endif
#endif
// Shorthand
#define GRID_MAX_POINTS ((GRID_MAX_POINTS_X) * (GRID_MAX_POINTS_Y))
// Add commands that need sub-codes to this list
#define USE_GCODE_SUBCODES ENABLED(G38_PROBE_TARGET)
// MESH_BED_LEVELING overrides PROBE_MANUALLY
#if ENABLED(MESH_BED_LEVELING)
#undef PROBE_MANUALLY
#endif
// Parking Extruder
#if ENABLED(PARKING_EXTRUDER)
#ifndef PARKING_EXTRUDER_GRAB_DISTANCE
#define PARKING_EXTRUDER_GRAB_DISTANCE 0
#endif
#ifndef PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE HIGH
#endif
#endif
#endif // CONDITIONALS_POST_H