You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

114 lines
3.1 KiB

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Teensylu 0.7 pin assignments (AT90USB1286)
* Requires the Teensyduino software with Teensy++ 2.0 selected in Arduino IDE!
* http://www.pjrc.com/teensy/teensyduino.html
* See http://reprap.org/wiki/Printrboard for more info
*/
#ifndef __AVR_AT90USB1286__
#error "Oops! Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu."
#endif
#if ENABLED(AT90USBxx_TEENSYPP_ASSIGNMENTS) // use Teensyduino Teensy++2.0 pin assignments instead of Marlin traditional.
#error "These Teensylu assignments depend on traditional Marlin assignments, not AT90USBxx_TEENSYPP_ASSIGNMENTS in fastio.h"
#endif
#define BOARD_NAME "Teensylu"
#define USBCON 1286 // Disable MarlinSerial etc.
#define LARGE_FLASH true
//
// Limit Switches
//
#define X_STOP_PIN 13
#define Y_STOP_PIN 14
#define Z_STOP_PIN 15
//
// Steppers
//
#define X_STEP_PIN 0
#define X_DIR_PIN 1
#define X_ENABLE_PIN 39
#define Y_STEP_PIN 2
#define Y_DIR_PIN 3
#define Y_ENABLE_PIN 38
#define Z_STEP_PIN 4
#define Z_DIR_PIN 5
#define Z_ENABLE_PIN 23
#define E0_STEP_PIN 6
#define E0_DIR_PIN 7
#define E0_ENABLE_PIN 19
//
// Temperature Sensors
//
#define TEMP_0_PIN 7 // Analog Input (Extruder)
#define TEMP_BED_PIN 6 // Analog Input (Bed)
//
// Heaters / Fans
//
#define HEATER_0_PIN 21 // Extruder
#define HEATER_1_PIN 46
#define HEATER_2_PIN 47
#define HEATER_BED_PIN 20
// If soft or fast PWM is off then use Teensyduino pin numbering, Marlin
// fastio pin numbering otherwise
#if ENABLED(FAN_SOFT_PWM) || ENABLED(FAST_PWM_FAN)
#define FAN_PIN 22
#else
#define FAN_PIN 16
#endif
//
// Misc. Functions
//
#define SDSS 8
//
// LCD / Controller
//
#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
#define BEEPER_PIN -1
#if ENABLED(LCD_I2C_PANELOLU2)
#define BTN_EN1 27 // RX1 - fastio.h pin mapping 27
#define BTN_EN2 26 // TX1 - fastio.h pin mapping 26
#define BTN_ENC 43 // A3 - fastio.h pin mapping 43
#define SDSS 40 // use SD card on Panelolu2 (Teensyduino pin mapping)
#endif // LCD_I2C_PANELOLU2
#define SD_DETECT_PIN -1
#endif // ULTRA_LCD && NEWPANEL