Let's Split
======
This readme and most of the code are from https://github.com/ahtn/tmk_keyboard/
Split keyboard firmware for Arduino Pro Micro or other ATmega32u4
based boards.
## First Time Setup
Download or clone the whole firmware and navigate to the keyboards/lets_split directory. Once your dev env is setup, you'll be able to generate the default .hex using:
```
$ make rev2
```
You will see a lot of output and if everything worked correctly you will see the built hex files:
```
lets_split_rev2_serial.hex
lets_split_rev2_i2c.hex
```
If you would like to use one of the alternative keymaps, or create your own, copy one of the existing [keymaps ](keymaps/ ) and run make like so:
```
$ make rev2-YOUR_KEYMAP_NAME
```
If everything worked correctly you will see a file:
```
lets_split_rev2_YOUR_KEYMAP_NAME.hex
```
For more information on customizing keymaps, take a look at the primary documentation for [Customizing Your Keymap ](/readme.md##customizing-your-keymap ) in the main readme.md.
### Let's split 1.0
If you have a first generation Let's Split you will need to use the revision 1 code. To do so, use `rev1` in all your commands instead.
Features
--------
For the full Quantum Mechanical Keyboard feature list, see [the parent readme.md ](/readme.md ).
Some features supported by the firmware:
* Either half can connect to the computer via USB, or both halves can be used
independently.
* You only need 3 wires to connect the two halves. Two for VCC and GND and one
for serial communication.
* Optional support for I2C connection between the two halves if for some
reason you require a faster connection between the two halves. Note this
requires an extra wire between halves and pull-up resistors on the data lines.
Required Hardware
-----------------
Apart from diodes and key switches for the keyboard matrix in each half, you
will need:
* 2 Arduino Pro Micro's. You can find theses on aliexpress for ≈3.50USD each.
* 2 TRS sockets
* 1 TRS cable.
Alternatively, you can use any sort of cable and socket that has at least 3
wires. If you want to use I2C to communicate between halves, you will need a
cable with at least 4 wires and 2x 4.7kΩ pull-up resistors
Optional Hardware
-----------------
A speaker can be hooked-up to either side to the `5` (`C6`) pin and `GND` , and turned on via `AUDIO_ENABLE` .
Wiring
------
The 3 wires of the TRS cable need to connect GND, VCC, and digital pin 3 (i.e.
PD0 on the ATmega32u4) between the two Pro Micros.
Then wire your key matrix to any of the remaining 17 IO pins of the pro micro
and modify the `matrix.c` accordingly.
The wiring for serial:
The wiring for i2c:
The pull-up resistors may be placed on either half. It is also possible
to use 4 resistors and have the pull-ups in both halves, but this is
unnecessary in simple use cases.
Notes on Software Configuration
-------------------------------
Configuring the firmware is similar to any other QMK project. One thing
to note is that `MATIX_ROWS` in `config.h` is the total number of rows between
the two halves, i.e. if your split keyboard has 4 rows in each half, then
`MATRIX_ROWS=8` .
Also the current implementation assumes a maximum of 8 columns, but it would
not be very difficult to adapt it to support more if required.
Flashing
-------
From the keymap directory run `make SUBPROJECT-KEYMAP-avrdude` for automatic serial port resolution and flashing.
Example: `make rev2-serial-avrdude`
Choosing which board to plug the USB cable into (choosing Master)
--------
Because the two boards are identical, the firmware has logic to differentiate the left and right board.
It uses two strategies to figure things out: look at the EEPROM (memory on the chip) or looks if the current board has the usb cable.
The EEPROM approach requires additional setup (flashing the eeeprom) but allows you to swap the usb cable to either side.
The USB cable approach is easier to setup and if you just want the usb cable on the left board, you do not need to do anything extra.
### Setting the left hand as master
If you always plug the usb cable into the left board, nothing extra is needed as this is the default. Comment out `EE_HANDS` and comment out `I2C_MASTER_RIGHT` if for some reason it was set.
### Setting the right hand as master
If you always plug the usb cable into the right board, add an extra flag to your `config.h`
```
#define I2C_MASTER_RIGHT
```
### Setting EE_hands to use either hands as master
If you define `EE_HANDS` in your `config.h` , you will need to set the
EEPROM for the left and right halves.
The EEPROM is used to store whether the
half is left handed or right handed. This makes it so that the same firmware
file will run on both hands instead of having to flash left and right handed
versions of the firmware to each half. To flash the EEPROM file for the left
half run:
```
avrdude -p atmega32u4 -P $(COM_PORT) -c avr109 -U eeprom:w:eeprom-lefthand.eep
// or the equivalent in dfu-programmer
```
and similarly for right half
```
avrdude -p atmega32u4 -P $(COM_PORT) -c avr109 -U eeprom:w:eeprom-righhand.eep
// or the equivalent in dfu-programmer
```
NOTE: replace `$(COM_PORT)` with the port of your device (e.g. `/dev/ttyACM0` )
After you have flashed the EEPROM, you then need to set `EE_HANDS` in your config.h, rebuild the hex files and reflash.
Note that you need to program both halves, but you have the option of using
different keymaps for each half. You could program the left half with a QWERTY
layout and the right half with a Colemak layout using bootmagic's default layout option.
Then if you connect the left half to a computer by USB the keyboard will use QWERTY and Colemak when the
right half is connected.
Notes on Using Pro Micro 3.3V
-----------------------------
Do update the `F_CPU` parameter in `rules.mk` to `8000000` which reflects
the frequency on the 3.3V board.
Also, if the slave board is producing weird characters in certain columns,
update the following line in `matrix.c` to the following:
```
// _delay_us(30); // without this wait read unstable value.
_delay_us(300); // without this wait read unstable value.
```
