qmk_firmware/Demos/Host/LowLevel/MIDIHost/MIDIHost.c

/*
             LUFA Library
     Copyright (C) Dean Camera, 2009.
              
  dean [at] fourwalledcubicle [dot] com
      www.fourwalledcubicle.com
*/

/*
  Copyright 2009  Dean Camera (dean [at] fourwalledcubicle [dot] com)

  Permission to use, copy, modify, and distribute this software
  and its documentation for any purpose and without fee is hereby
  granted, provided that the above copyright notice appear in all
  copies and that both that the copyright notice and this
  permission notice and warranty disclaimer appear in supporting
  documentation, and that the name of the author not be used in
  advertising or publicity pertaining to distribution of the
  software without specific, written prior permission.

  The author disclaim all warranties with regard to this
  software, including all implied warranties of merchantability
  and fitness.  In no event shall the author be liable for any
  special, indirect or consequential damages or any damages
  whatsoever resulting from loss of use, data or profits, whether
  in an action of contract, negligence or other tortious action,
  arising out of or in connection with the use or performance of
  this software.
*/

/** \file
 *
 *  Main source file for the MIDIHost demo. This file contains the main tasks of
 *  the demo and is responsible for the initial application hardware configuration.
 */
 
#include "MIDIHost.h"

/** Main program entry point. This routine configures the hardware required by the application, then
 *  enters a loop to run the application tasks in sequence.
 */
int main(void)
{
	SetupHardware();

	puts_P(PSTR(ESC_FG_CYAN "MIDI Host Demo running.\r\n" ESC_FG_WHITE));

	LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);

	for (;;)
	{
		MIDI_Host_Task();
		USB_USBTask();
	}
}

/** Configures the board hardware and chip peripherals for the demo's functionality. */
void SetupHardware(void)
{
	/* Disable watchdog if enabled by bootloader/fuses */
	MCUSR &= ~(1 << WDRF);
	wdt_disable();

	/* Disable clock division */
	clock_prescale_set(clock_div_1);

	/* Hardware Initialization */
	SerialStream_Init(9600, false);
	LEDs_Init();
	Buttons_Init();
	Joystick_Init();
	USB_Init();
}

/** Event handler for the USB_DeviceAttached event. This indicates that a device has been attached to the host, and
 *  starts the library USB task to begin the enumeration and USB management process.
 */
void EVENT_USB_Host_DeviceAttached(void)
{
	puts_P(PSTR(ESC_FG_GREEN "Device Attached.\r\n" ESC_FG_WHITE));
	LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
}

/** Event handler for the USB_DeviceUnattached event. This indicates that a device has been removed from the host, and
 *  stops the library USB task management process.
 */
void EVENT_USB_Host_DeviceUnattached(void)
{
	puts_P(PSTR(ESC_FG_GREEN "\r\nDevice Unattached.\r\n" ESC_FG_WHITE));
	LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
}

/** Event handler for the USB_DeviceEnumerationComplete event. This indicates that a device has been successfully
 *  enumerated by the host and is now ready to be used by the application.
 */
void EVENT_USB_Host_DeviceEnumerationComplete(void)
{
	LEDs_SetAllLEDs(LEDMASK_USB_READY);
}

/** Event handler for the USB_HostError event. This indicates that a hardware error occurred while in host mode. */
void EVENT_USB_Host_HostError(const uint8_t ErrorCode)
{
	USB_ShutDown();

	printf_P(PSTR(ESC_FG_RED "Host Mode Error\r\n"
	                         " -- Error Code %d\r\n" ESC_FG_WHITE), ErrorCode);

	LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
	for(;;);
}

/** Event handler for the USB_DeviceEnumerationFailed event. This indicates that a problem occurred while
 *  enumerating an attached USB device.
 */
void EVENT_USB_Host_DeviceEnumerationFailed(const uint8_t ErrorCode, const uint8_t SubErrorCode)
{
	printf_P(PSTR(ESC_FG_RED "Dev Enum Error\r\n"
	                         " -- Error Code %d\r\n"
	                         " -- Sub Error Code %d\r\n"
	                         " -- In State %d\r\n" ESC_FG_WHITE), ErrorCode, SubErrorCode, USB_HostState);
	
	LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
}

/** Task to set the configuration of the attached device after it has been enumerated, and to read in
 *  note on/off messages from the attached MIDI device and print it to the serial port. When the board
 *  joystick or buttons are pressed, note on/off messages are sent to the attached device.
 */
void MIDI_Host_Task(void)
{
	uint8_t ErrorCode;

	switch (USB_HostState)
	{
		case HOST_STATE_Addressed:
			puts_P(PSTR("Getting Config Data.\r\n"));
		
			/* Get and process the configuration descriptor data */
			if ((ErrorCode = ProcessConfigurationDescriptor()) != SuccessfulConfigRead)
			{
				if (ErrorCode == ControlError)
				  puts_P(PSTR(ESC_FG_RED "Control Error (Get Configuration).\r\n"));
				else
				  puts_P(PSTR(ESC_FG_RED "Invalid Device.\r\n"));

				printf_P(PSTR(" -- Error Code: %d\r\n" ESC_FG_WHITE), ErrorCode);
				
				/* Indicate error via status LEDs */
				LEDs_SetAllLEDs(LEDMASK_USB_ERROR);

				/* Wait until USB device disconnected */
				USB_HostState = HOST_STATE_WaitForDeviceRemoval;
				break;
			}
			
			/* Set the device configuration to the first configuration (rarely do devices use multiple configurations) */
			if ((ErrorCode = USB_Host_SetDeviceConfiguration(1)) != HOST_SENDCONTROL_Successful)
			{
				printf_P(PSTR(ESC_FG_RED "Control Error (Set Configuration).\r\n"
				                         " -- Error Code: %d\r\n" ESC_FG_WHITE), ErrorCode);

				/* Indicate error via status LEDs */
				LEDs_SetAllLEDs(LEDMASK_USB_ERROR);

				/* Wait until USB device disconnected */
				USB_HostState = HOST_STATE_WaitForDeviceRemoval;
				break;
			}

			puts_P(PSTR("MIDI Device Enumerated.\r\n"));

			USB_HostState = HOST_STATE_Configured;
			break;
		case HOST_STATE_Configured:
			Pipe_SelectPipe(MIDI_DATAPIPE_IN);
			
			if (Pipe_IsINReceived())
			{
				USB_MIDI_EventPacket_t MIDIEvent;
				
				Pipe_Read_Stream_LE(&MIDIEvent, sizeof(MIDIEvent));
				
				bool NoteOnEvent  = ((MIDIEvent.Command & 0x0F) == (MIDI_COMMAND_NOTE_ON  >> 4));
				bool NoteOffEvent = ((MIDIEvent.Command & 0x0F) == (MIDI_COMMAND_NOTE_OFF >> 4));
				
				if (NoteOnEvent || NoteOffEvent)
				{
					printf_P(PSTR("MIDI Note %s - Channel %d, Pitch %d, Velocity %d"), NoteOnEvent ? "On" : "Off",
				                                                                       ((MIDIEvent.Data1 & 0x0F) + 1),
				                                                                       MIDIEvent.Data2, MIDIEvent.Data3);
				}

				Pipe_ClearIN();
			}
			
			Pipe_SelectPipe(MIDI_DATAPIPE_OUT);
			
			static uint8_t PrevJoystickStatus;

			if (Pipe_IsOUTReady())
			{
				uint8_t MIDICommand = 0;
				uint8_t MIDIPitch;
			
				uint8_t JoystickStatus  = Joystick_GetStatus();
				uint8_t JoystickChanges = (JoystickStatus ^ PrevJoystickStatus);
				
				/* Get board button status - if pressed use channel 10 (percussion), otherwise use channel 1 */
				uint8_t Channel = ((Buttons_GetStatus() & BUTTONS_BUTTON1) ? MIDI_CHANNEL(10) : MIDI_CHANNEL(1));

				if (JoystickChanges & JOY_LEFT)
				{
					MIDICommand = ((JoystickStatus & JOY_LEFT)? MIDI_COMMAND_NOTE_ON : MIDI_COMMAND_NOTE_OFF);
					MIDIPitch   = 0x3C;
				}

				if (JoystickChanges & JOY_UP)
				{
					MIDICommand = ((JoystickStatus & JOY_UP)? MIDI_COMMAND_NOTE_ON : MIDI_COMMAND_NOTE_OFF);
					MIDIPitch   = 0x3D;
				}

				if (JoystickChanges & JOY_RIGHT)
				{
					MIDICommand = ((JoystickStatus & JOY_RIGHT)? MIDI_COMMAND_NOTE_ON : MIDI_COMMAND_NOTE_OFF);
					MIDIPitch   = 0x3E;
				}
				
				if (JoystickChanges & JOY_DOWN)
				{
					MIDICommand = ((JoystickStatus & JOY_DOWN)? MIDI_COMMAND_NOTE_ON : MIDI_COMMAND_NOTE_OFF);
					MIDIPitch   = 0x3F;
				}

				if (JoystickChanges & JOY_PRESS)
				{
					MIDICommand = ((JoystickStatus & JOY_PRESS)? MIDI_COMMAND_NOTE_ON : MIDI_COMMAND_NOTE_OFF);
					MIDIPitch   = 0x3B;
				}

				/* Check if a MIDI command is to be sent */
				if (MIDICommand)
				{
					USB_MIDI_EventPacket_t MIDIEvent = (USB_MIDI_EventPacket_t)
						{
							.CableNumber = 0,
							.Command     = (MIDICommand >> 4),
							
							.Data1       = MIDICommand | Channel,
							.Data2       = MIDIPitch,
							.Data3       = MIDI_STANDARD_VELOCITY,			
						};
						
					/* Write the MIDI event packet to the pipe */
					Pipe_Write_Stream_LE(&MIDIEvent, sizeof(MIDIEvent));
				
					/* Send the data in the pipe to the device */
					Pipe_ClearOUT();
				}
				
				/* Save previous joystick value for next joystick change detection */
				PrevJoystickStatus = JoystickStatus;
			}

			break;
	}
}