You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
qmk_firmware/Projects/AVRISP-MKII/Lib/XPROG/XPROGTarget.c

206 lines
5.8 KiB

/*
LUFA Library
Copyright (C) Dean Camera, 2010.
dean [at] fourwalledcubicle [dot] com
www.lufa-lib.org
*/
/*
Copyright 2010 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, distribute, and sell this
software and its documentation for any purpose is hereby granted
without fee, provided that the above copyright notice appear in
all copies and that both that the copyright notice and this
permission notice and warranty disclaimer appear in supporting
documentation, and that the name of the author not be used in
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
The author disclaim all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
whatsoever resulting from loss of use, data or profits, whether
in an action of contract, negligence or other tortious action,
arising out of or in connection with the use or performance of
this software.
*/
/** \file
*
* Target-related functions for the PDI Protocol decoder.
*/
#define INCLUDE_FROM_XPROGTARGET_C
#include "XPROGTarget.h"
#if defined(ENABLE_XPROG_PROTOCOL) || defined(__DOXYGEN__)
/** Flag to indicate if the USART is currently in Tx or Rx mode. */
volatile bool IsSending;
/** Enables the target's PDI interface, holding the target in reset until PDI mode is exited. */
void XPROGTarget_EnableTargetPDI(void)
{
IsSending = false;
/* Set Tx and XCK as outputs, Rx as input */
DDRD |= (1 << 5) | (1 << 3);
DDRD &= ~(1 << 2);
/* Set DATA line high for at least 90ns to disable /RESET functionality */
PORTD |= (1 << 3);
_delay_us(1);
/* Set up the synchronous USART for XMEGA communications - 8 data bits, even parity, 2 stop bits */
UBRR1 = (F_CPU / XPROG_HARDWARE_SPEED);
UCSR1B = (1 << TXEN1);
UCSR1C = (1 << UMSEL10) | (1 << UPM11) | (1 << USBS1) | (1 << UCSZ11) | (1 << UCSZ10) | (1 << UCPOL1);
/* Send two BREAKs of 12 bits each to enable PDI interface (need at least 16 idle bits) */
XPROGTarget_SendBreak();
XPROGTarget_SendBreak();
}
/** Enables the target's TPI interface, holding the target in reset until TPI mode is exited. */
void XPROGTarget_EnableTargetTPI(void)
{
IsSending = false;
/* Set /RESET line low for at least 400ns to enable TPI functionality */
AUX_LINE_DDR |= AUX_LINE_MASK;
AUX_LINE_PORT &= ~AUX_LINE_MASK;
_delay_us(1);
/* Set Tx and XCK as outputs, Rx as input */
DDRD |= (1 << 5) | (1 << 3);
DDRD &= ~(1 << 2);
/* Set up the synchronous USART for TINY communications - 8 data bits, even parity, 2 stop bits */
UBRR1 = (F_CPU / XPROG_HARDWARE_SPEED);
UCSR1B = (1 << TXEN1);
UCSR1C = (1 << UMSEL10) | (1 << UPM11) | (1 << USBS1) | (1 << UCSZ11) | (1 << UCSZ10) | (1 << UCPOL1);
/* Send two BREAKs of 12 bits each to enable TPI interface (need at least 16 idle bits) */
XPROGTarget_SendBreak();
XPROGTarget_SendBreak();
}
/** Disables the target's PDI interface, exits programming mode and starts the target's application. */
void XPROGTarget_DisableTargetPDI(void)
{
/* Switch to Rx mode to ensure that all pending transmissions are complete */
XPROGTarget_SetRxMode();
/* Turn off receiver and transmitter of the USART, clear settings */
UCSR1A = ((1 << TXC1) | (1 << RXC1));
UCSR1B = 0;
UCSR1C = 0;
/* Tristate all pins */
DDRD &= ~((1 << 5) | (1 << 3));
PORTD &= ~((1 << 5) | (1 << 3) | (1 << 2));
}
/** Disables the target's TPI interface, exits programming mode and starts the target's application. */
void XPROGTarget_DisableTargetTPI(void)
{
/* Switch to Rx mode to ensure that all pending transmissions are complete */
XPROGTarget_SetRxMode();
/* Turn off receiver and transmitter of the USART, clear settings */
UCSR1A |= (1 << TXC1) | (1 << RXC1);
UCSR1B = 0;
UCSR1C = 0;
/* Set all USART lines as input, tristate */
DDRD &= ~((1 << 5) | (1 << 3));
PORTD &= ~((1 << 5) | (1 << 3) | (1 << 2));
/* Tristate target /RESET line */
AUX_LINE_DDR &= ~AUX_LINE_MASK;
AUX_LINE_PORT &= ~AUX_LINE_MASK;
}
/** Sends a byte via the USART.
*
* \param[in] Byte Byte to send through the USART
*/
void XPROGTarget_SendByte(const uint8_t Byte)
{
/* Switch to Tx mode if currently in Rx mode */
if (!(IsSending))
XPROGTarget_SetTxMode();
/* Wait until there is space in the hardware Tx buffer before writing */
while (!(UCSR1A & (1 << UDRE1)));
UCSR1A |= (1 << TXC1);
UDR1 = Byte;
}
/** Receives a byte via the software USART, blocking until data is received.
*
* \return Received byte from the USART
*/
uint8_t XPROGTarget_ReceiveByte(void)
{
/* Switch to Rx mode if currently in Tx mode */
if (IsSending)
XPROGTarget_SetRxMode();
/* Wait until a byte has been received before reading */
while (!(UCSR1A & (1 << RXC1)) && TimeoutTicksRemaining);
return UDR1;
}
/** Sends a BREAK via the USART to the attached target, consisting of a full frame of idle bits. */
void XPROGTarget_SendBreak(void)
{
/* Switch to Tx mode if currently in Rx mode */
if (!(IsSending))
XPROGTarget_SetTxMode();
/* Need to do nothing for a full frame to send a BREAK */
for (uint8_t i = 0; i < BITS_IN_USART_FRAME; i++)
{
/* Wait for a full cycle of the clock */
while (PIND & (1 << 5));
while (!(PIND & (1 << 5)));
}
}
static void XPROGTarget_SetTxMode(void)
{
/* Wait for a full cycle of the clock */
while (PIND & (1 << 5));
while (!(PIND & (1 << 5)));
PORTD |= (1 << 3);
DDRD |= (1 << 3);
UCSR1B &= ~(1 << RXEN1);
UCSR1B |= (1 << TXEN1);
IsSending = true;
}
static void XPROGTarget_SetRxMode(void)
{
while (!(UCSR1A & (1 << TXC1)));
UCSR1A |= (1 << TXC1);
UCSR1B &= ~(1 << TXEN1);
UCSR1B |= (1 << RXEN1);
DDRD &= ~(1 << 3);
PORTD &= ~(1 << 3);
IsSending = false;
}
#endif