You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
qmk_firmware/Projects/AVRISP_Programmer/Sample_Programming_Session.txt

105 lines
4.3 KiB

ubuntu@ubuntu:~/LUFA/Bootloaders/LUFA_DFU_Bootloader_AT90USB162$ sudo avrdude -vv -F -P /dev/ttyACM0 -c avr910 -p usb162 -U flash:w:BootloaderDFU.hex
avrdude: Version 5.5, compiled on May 9 2008 at 13:04:46
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
System wide configuration file is "/etc/avrdude.conf"
User configuration file is "/home/ubuntu/.avrduderc"
User configuration file does not exist or is not a regular file, skipping
Using Port : /dev/ttyACM0
Using Programmer : avr910
AVR Part : AT90USB162
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PA0
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 10 8 0 no 512 4 0 9000 9000 0x00 0x00
flash 65 6 128 0 yes 16384 128 128 4500 4500 0x00 0x00
lfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
efuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
lock 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : avr910
Description : Atmel Low Cost Serial Programmer
Found programmer: Id = "AVR ISP"; type = S
Software Version = 2.3; Hardware Version = 1.0
Programmer supports auto addr increment.
Programmer supports the following devices:
Device code: 0x55 = ATtiny12
Device code: 0x56 = ATtiny15
Device code: 0x5e = ATtiny2313
Device code: 0x76 = ATMEGA8
Device code: 0x74 = ATMEGA6450
Device code: 0x72 = ATMEGA32
Device code: 0x45 = ATMEGA64
Device code: 0x74 = ATMEGA6450
Device code: 0x43 = ATMEGA128
Device code: 0x63 = ATMEGA162
Device code: 0x78 = ATMEGA169
Device code: 0x6c = AT90S4434
Device code: 0x38 = AT90S8515
Device code: 0x65 = (unknown)
avrdude: warning: selected device is not supported by programmer: usb162
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.00s
avrdude: Device signature = 0x1e9482
avrdude: safemode: lfuse reads as 5E
avrdude: safemode: hfuse reads as D9
avrdude: safemode: efuse reads as F4
avrdude: NOTE: FLASH memory has been specified, an erase cycle will be performed
To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file "BootloaderDFU.hex"
avrdude: input file BootloaderDFU.hex auto detected as Intel Hex
avrdude: writing flash (16066 bytes):
Writing | ################################################## | 100% 33.39s
avrdude: 16066 bytes of flash written
avrdude: verifying flash memory against BootloaderDFU.hex:
avrdude: load data flash data from input file BootloaderDFU.hex:
avrdude: input file BootloaderDFU.hex auto detected as Intel Hex
avrdude: input file BootloaderDFU.hex contains 16066 bytes
avrdude: reading on-chip flash data:
Reading | ################################################## | 100% 16.07s
avrdude: verifying ...
avrdude: 16066 bytes of flash verified
avrdude: safemode: lfuse reads as 5E
avrdude: safemode: hfuse reads as D9
avrdude: safemode: efuse reads as F4
avrdude: safemode: Fuses OK
avrdude done. Thank you.